山东省主栽果树生殖器官中稀土与微量营养元素的相关性研究

通过对山东省5大类主栽果树20余个树种的花粉、种子和果实稀土与微量元素自然含量进行分析比较, 认为稀土(RE)与微量元素在各树种花粉中平均含量顺序为Fe＞Zn＞B＞Cu＞Mn＞RE, 种子中B＞Fe＞Zn＞Mn＞Cu＞RE, 果实中Fe＞B＞Zn＞Cu＞Mn＞RE. 各元素在各生殖器官中的自然分布因树种而有很大差异. 但基本规律类同, 即花粉＞种子＞果实. 花粉富集各种微量营养元素的能力都很强. 花粉和果实稀土与微量元素之间绝大多数呈正相关, 种子大多呈负相关, 但相关性均不显著.     

冶金炉料中二氧化硅和碳化硅的联合测定

提出冶金炉料中二氧化硅及碳化硅的联合测定方法，硝酸－氢氟酸－盐酸溶解二氧化硅，用硅氟酸钾容量法测定，残渣经焦硫酸钾溶解杂质，不溶碳化硅以重量法测定，经试样全分析及精密度考证，方法简便、可靠．     

N,O-羧甲基壳聚糖的合成和性质研究

采用多段升温法将壳聚糖改性,合成了取代度为1.84、平均分子量为3.08×105、等电点为7.28的N,O-羧甲基壳聚糖(CMC),分别用紫外光谱、红外光谱、荧光光谱对其结构进行了表征,并对其水溶液的Zeta电位、电导率、表面张力以及水分散体系中羧甲基壳聚糖微粒的粒径分布进行了研究.结果表明, N,O-羧甲基壳聚糖具有表面活性;介质的pH值和浓度对羧甲基壳聚糖溶液的稳定性有很大的影响.     

哒螨灵在苹果和土壤上残留以及降解行为研究

本研究建立了基于高效液相色谱为基础的哒螨灵分析方法,并对哒螨灵在安徽淮北和陕西咸阳两地苹果上的消解和残留行为进行了研究,同时还考察了哒螨灵在两地土壤中的降解和残留行为．哒螨灵在苹果中的消解动态方程：陕西咸阳为C=0．4007e^-0.1535t,半衰期T1/2=4．5天;安徽淮北=0．1096e^-0.1464t,半衰期T1/2=4．7天;在土壤中的消解动态方程：陕西咸阳为C=0．7978e^0.1218t,半衰期T1/2=5．7天;安徽淮北C=1．4024e^-0.0912t,半衰期T1/2=7．6天．在推荐使用高剂量和推荐高剂量1．5倍情况下,施药1-2次,末次药后7天,哒螨灵在苹果中的残留为0．02～0．14mg／kg;药后14天为0．01—0．12mg／kg．试验结果表明,药后7天,苹果中哒螨灵的残留量低于2mg／kg,用药次数1-2次,每次间隔7天的情况下,在苹果上的安全间隔期可定为7天．     

蟹,虾壳微观形貌与结构研究

用Ｘ射线衍射与扫描电镜研究了蟹壳，虾壳的形貌与微观结构，蟹壳中以方解石晶型存在的碳酸钙分布在网状结构的有机质中，网孔的尺寸约５～２５μｍ有机基质脱去蛋白后留下的甲壳质呈片层状结构，它的重复距离为０．９６ｎｍ。     

Physico-chemical aspects of polyethylene processing in an open mixer. Part 17. Effect of oxygen availability

The gas in contact with polyethylene has considerable impact on its oxidation. The rate of oxidation product formation is mostly larger with oxygen blanketing than in air. Similarly, the rate in air is larger than that under nitrogen blanketing. Moreover, the relative effect of the surrounding gas is depending heavily on the particular oxidation product considered. The effect on the alcohol concentration on passing from air to pure oxygen is the same as that on the hydroperoxide concentration. It is only under pure nitrogen that alcohol formation is relatively more affected than hydroperoxide formation. The overall carbonyl groups as well as the ketones show the expected ranking, i.e. faster rate in pure oxygen than in air and faster rate in air than under pure nitrogen. However, carboxylic acids are formed much faster in oxygen than in air. For the acids the results in air and under nitrogen are significantly closer in the initial stages of processing than the results obtained under pure oxygen. This is different for γ-lactones for which formation is faster in oxygen than in air where it is faster than under nitrogen. With trans-vinylene groups the situation is opposite to that observed for carboxylic acids: the rate of formation is close for the experiments performed under air and under oxygen and significantly faster than under nitrogen. The results for hydroperoxides, alcohols and ketones are easily interpreted taking into account the kinetics developed in previous work. Fitting the data to the heterogeneous kinetics shows the effect of the oxygen concentration on this kinetics. It is especially unexpected with respect to its impact on the initiation rate. It is discussed taking into account various possibilities. The only one that is compatible with all the data envisages chain initiation resulting from interaction of oxygen with strained polymer molecules.     

五羰基合铁分子化学键特性的研究

We have found from experimental data that, in the iron pentacarbonyl molecule, the length of Fe-C bond in axial is shorter than that in planar, but the bond is weaker; the bond distances of C-O of both planar and axial are equal, while the bond strengths are different. This is against the traditional view of “the shorter the bond is, the stronger the bond will be”. We have got through calculation and research, that the main cause of such difference is that the effects of the backdonor of Fe atom′s electrons to C-O bonds in axial and planar are different. The shorter the Fe-C bond is, the more effective the backdonor (or transfer) of electrons is. So that the population between Fe and C in axial are less than those in planar, so the bond is weaker, and the C-O bonds have gained more backdonor electrons than those in planar, thus the bond is stronger.     

Generalized doubly symbolic formulation for integral-driven direct configuration interaction method

Summary A direct configuration interaction (CI) scheme using the generalized double symbolism both for the external space and for the internal space is proposed in an integral-driven context. The reason why the double symbolism is used in the present formulation is that the main target is in investigating large molecular systems. The integrals, configuration state functions, and energy expressions are systematically classified in terms of the orbital labels and their mutual relations. Various types of CI wavefunctions can be set up flexibly. The resulting structure of integral processings in the sigma vector construction is complicated. The number of unique loop types for two-electron integrals is 1325. Because the parallel architecture is gaining importance in the recent computational platforms, the parallelism is also addressed.     

铅锡合金准二维电沉积的微结构研究

铅锡合金的准二维电沉积物具有伪共晶-固溶体双层结构.研究表明,这种奇特的结构是由生长界面上电流密度自发变化引起的.当生长界面处于整个沉积物前端时,电流密度大,铅和锡共同沉积形成伪共晶组织;当生长界面处于整个沉积物后端时,电流密度小,铅沉积成为主要反应,此时沉积物是含铅较多的固溶体组织.     

含钪铝镁合金微生物腐蚀行为的研究

采用电化学、微生物学和表面分析的方法，研究了厌氧环境硫酸盐还原菌（subtere ducing bacteria，SRB）溶液中Al-6Mg-Zr添加Sc元素前后的腐蚀行为。结果表明，添加Sc元素后，合金的氧化膜更加致密，具有更好的保护作用，使电极开路电位正移100mV左右，同时Sc元素的加入降低了材料在SRB菌液中的点蚀敏感性，使材料耐微生物腐蚀性能得到提高，但是添加Sc后的合金对SRB更加敏感。显微观察表明添加Sc前后两种铝镁合金的腐蚀特征均为点蚀，能谱分析表明随浸泡时间增加，腐蚀越来越严重，腐蚀产物堆积和阳极金属溶解造成进一步腐蚀。     

Fe-Al-α,α′-联吡啶催化体系催化马来酸酐与环氧丙烷开环共聚

马来酸酐与环氧丙烷开环共聚,所得聚酯具有功能团（C＝C）,可以通过接技、交联待方法改变其性能,马来酸杆与环氧化物开环共聚合成聚酯,所用催化剂通用有有机金属化合物和稀土 事物等,我们在铁系催化丁二聚合和马来酸酐与苯乙烯共聚的基础上,首次将Fe(acac)3-Al(i-Bu)3-α,α′－联吡啶催化剂用于马来酸酐与环氧化物开环共聚,发现该催化剂催化共聚反应具有时间短、收率高、共聚物交替度高等优点,并测定了共聚合反应动力学的参数。     

钾盐矿床中含石膏盐分析方法的研究

由于现行标准《岩石矿物分析规程》(DZG93-08)对含石膏钾盐样品分析方法的叙述较为粗略,同时没有国家一级有证标准物质进行质量监控,因此在测定含石膏钾盐样品时较为困难。本文讨论了溶矿温度、称样量、以及放置时间对含石膏钾盐样品溶解的影响。得出在称样量为0.5000g,水温80℃,放置时间为24小时,用电感耦合等离子体发射光谱法测定,以样品中各组分百分数加和、溶液中元素阴阳离子平衡以及加标回收实验进行数据质量监控。测试数据符合《地质矿产实验室测试质量管理规范》对钾盐样品分析质量的要求。     

原子吸收光谱法间接测定萤石中的全硫

基于SO42-和BaCrO4溶液反应生成BaSO4沉淀, 置换出定量的CrO42-, 通过原子吸收法测定Cr, 建立了间接测定萤石中硫的原子吸收光谱法. 方法的工作曲线范围0.05～20 μg/mL SO42-, 检出限为0.017 μg/mL S, 适用于硫质量分数在0.01%～3%范围内萤石样品的测定.     

Solar Light Active Graphitic Carbon Nitride/Biochar Nanocomposite for RhB Dye Degradation

In this work, nanocomposite graphitic carbon nitride/biochar is successfully prepared by physical mixing method to achieve efficient charge separation and photodegradation of RhB dye under sunlight. The biochar is synthesized by heating biomass in muffle furnace in an inert atmosphere. The graphitic carbon nitride is prepared using melamine as a precursor and heating it in a muffle furnace in air atmosphere. The structural characterizations FTIR and X-ray diffraction are done to confirm the functional groups and crystallography of prepared samples. The photodegradation of RhB dye by nanocomposite is analyzed using a UV–visible spectrophotometer under solar irradiation. It is found that the RhB dye is completely reduced by the nanocomposite in less than 6 min in the presence of sunlight. The kinetic study confirms the photodegradation of RhB dye is first order reaction and rate constant is found to be 0.31 min⁻¹.     

用于煤制天然气的气化-热解耦合系统模拟研究及能量分析

大规模煤制天然气系统中气流床气化是一种重要且富吸引力的技术。对一种气流床气化-热解耦合系统进行了研究。该系统中气化炉分为两段:主要进行煤焦气化的气化段以及主要发生煤热解的热解段。采用流程模拟方法建立了耦合系统模型并与煤气化废锅系统进行了比较。同时,考察了操作条件对耦合系统气化性能的影响,提出了优化的操作条件。结果显示,气化温度1400 ℃时,耦合系统优化的蒸汽煤比为250~300 kg(steam)·t^-1(dry coal)。耦合系统的冷煤气效率为88.18%,高于气化废锅系统(84.14%),且其消耗指标均有所降低。但耦合系统的气化性能受到热解段焦油和CH₄产率很大的影响。耦合系统总体能量利用效率为92.26%,略低于气化废锅系统(93.39%),但其火用效率比气化废锅系统高2.2%。这说明通过热解-气化的耦合方式能够有效回收气化高温合成气中的显热并提高其能量品位。     

肝癌与肝硬化腹水微量元素Cu、Zn测定的临床诊断价值

腹水是一种病理性腹腔渗出液或漏出波．肝癌、肝硬化晚期，腹膜炎等多种疾病可致病人出现腹水，由于引起腹水病因不同，腹水中各物质含量亦有所不同．关于腹水中微量元素含量的研究尚少见报道。为此作者分三组测定了４８份腹水中的Ｃｕ、Ｚｎ含量，进行了分析比较，结果如下：１．Ｃｕ含量．其它组高于肝癌组，肝癌组高于肝硬化组，各组间差异非常显著，Ｐ＜０．０１。２．Ｚｎ含量，肝癌组高于肝硬化组，肝硬化组高于其它组，各组间差异显著，Ｐ＜０．０５．３．以上结果说明，测定腹水中Ｃｕ、Ｚｎ含量是一项了解腹水性质较敏感指标，尤其是肝硬化癌变时，Ｃｕ、Ｚｎ含量有明显的变化．     

煤中微量元素的酸脱除率与元素周期律 |-以渭北晚古生代5号煤层为例

对比了渭北晚古生代5号煤样品酸处理前后微量元素含量的变化。结果表明,按其量化表征的煤中微量元素酸脱除率划分,44个微量元素可分为五类,它们在元素周期表中有着明显的分布规律：Ⅰ型,为煤中典型的易酸脱除微量元素,主要占据于元素周期表中第Ⅰ、Ⅱ主族元素位置,按电子构型,属s区;Ⅱ型,为煤中较易酸脱除微量元素;Ⅲ型,为煤中较难酸脱除微量元素,主要占据在第Ⅲ、Ⅴ、Ⅵ、Ⅷ副族元素位置上,按电子构型,属d区和f区左半部;Ⅳ型,是难酸脱除的微量元素,主要占据在第Ⅳ、Ⅴ主族元素位置,（稀土元素部分在第Ⅲ副族）按电子构型,属p区和f区中部;Ⅴ型,为典型的最难酸脱除微量元素,主要占据在第Ⅱ、Ⅲ、Ⅳ副族位置,按电子构型,属d区的前半部、ds区和f区的右半部。煤中微量元素的酸脱除难易的大小,在元素周期表的横向、纵向和对角线方向,亦有一定的变化规律。     

Shrinkability of ethylene vinyl acetate/polyurethane blends and their characterization

Heat shrinkability of the polymer, which depends on the elastic memory, is being utilized in various applications, mainly in the field of encapsulation. The elastic memory is introduced into the system in the form of an elastomeric phase. Here the blends of ethylene vinyl acetate and polyurethane were studied with reference to their shrinkability, introducing crosslinking in both the phases. It is found that with increase in elastomer content the shrinkage increased to a certain level and then decreased. With increase in cure time shrinkage is decreased. It is seen that high‐temperature (HT) stretched samples showed higher shrinkage than room temperature (RT) stretched one. Generally, the crystallinity of the HT stretched sample is higher than that of low‐temperature stretched sample, which is again higher than that of original sample. From high temperature differential scanning calorimetry it is found that with increase in PU content stability towards oxygen is increased and further high temperature processing decreases the initial degradation temperature but enhances the rate of degradation. From scanning electron microscopy it is seen that an HT stretched sample is more elongated than an RT stretched one. Copyright © 2000 John Wiley & Sons, Ltd.     

Electrohydrodynamic transport of non‐symmetric electrolyte through porous wall of a microtube

Transport of salt through the wall of porous microtube is relevant in various physiological microcirculation systems. Transport phenomena based modeling of such system is undertaken in the present study considering a combined driving force consisting of pressure gradient and external electric field. Transport of salt is modeled in two domains, in the flow conduit and in the pores of porous wall of the microtube. The solute transport in the microtube is presented by convective‐diffusive mass balance and it is solved using integral method under the framework of boundary layer analysis. The wall of the microtube is considered to be consisting of series of straight parallel cylindrical pores with charged inner surface. The solute transport through the pores is considered to be composed of diffusive, convective and electric potential gradient governed by Nernst‐Planck equation. Transport in the microtube and pores is coupled through the osmotic pressure model for the solvent and Donnan equilibrium distribution for the solute. The simulated results agree remarkably well with the experimental data conducted by in‐house experimental set up. The charge density of the porous wall is estimated through the minimization of errors involved between the experimental and simulated data for different operating conditions.     

钢铁及合金中钨测定的高氯酸氧化法

在磷酸介质中,冒烟高氯酸氧化钨成高价,并消除溶液中存在的还原物质的影响,用氯化亚锡及三氯化钛还原铁和钨,约3．6mol／L盐酸介质中,硫氰酸铵与钨（V）生成黄色络合物,通过测其吸光义可定量测定钨含量。由于较多量冒烟高氯酸的氧化作用,还原不需铁作催化剂,消除了基体铁的影响。测定质量分数范围为0．05％－10％。