Determination of 1-hydroxypyrene in human urine by high-performance liquid chromatography with fluorescence detection using a deuterated internal standard

A high-performance liquid chromatographic method has been developed for the quantification of 1-hydroxypyrene (1-OHP) in human urine using deuterated 1-hydroxypyrene ([2H9]1-OHP) as an internal standard with fluorescence detection. [2H9]1-OHP was prepared enzymatically from deuterated pyrene ([2H10]Pyr) with cytochrome P450 1A1. It eluted immediately prior to non-deuterated 1-OHP on alkylamide-type reversed-phase columns and had nearly the same fluorescence characteristics as non-deuterated 1-OHP. The detection limit was 0.1 microg/L and the calibration range was from 1 to 100 nmol/L. Urine sample treatment involved enzymatic hydrolysis followed by solid-phase extraction using Sep-Pak C18 cartridges. The proposed method was used to determine urinary 1-OHP in smokers and non-smokers.     

High-throughput on-line solid-phase extraction-liquid chromatography-tandem mass spectrometry method for the simultaneous analysis of 14 antidepressants and their metabolites in plasma

A rapid, sensitive and fully automated on-line solid-phase extraction-liquid chromatography-tandem mass spectrometry (SPE-LC-MS/MS) method was developed and validated for the direct analysis of 14 antidepressants and their metabolites in plasma. Integration of the sample extraction and LC separation into a single system permitted direct injection of the plasma without prior sample pre-treatment. The applied gradient ensured the elution of all the examined drugs within 14 min and produced chromatographic peaks of acceptable symmetry. The total process time was 20 min and only 50 microL of plasma was required. Selectivity of the method was achieved by a combination of retention time and two precursor-product ion transitions for the non-deuterated compounds. The use of SPE was demonstrated to be highly effective and led to significant decreases in the interferences present in the matrix. Extraction was found to be both reproducible and efficient with recoveries >99% for all the analytes. The method showed excellent intra-assay and inter-assay precision (relative standard deviation (RSD) and bias <20%) for quality control (QC) samples spiked at a concentration of 40, 200 and 800 microg/L and the r2>0.99 over the range investigated (10-1000 microg/L). Limits of quantification (LOQs) were estimated to be 10 microg/L. Furthermore, the processed samples were demonstrated to be stable for at least 48 h, except for clomipramine and norclomipramine, where a slight negative trend was observed, but did not compromise the quantification. The method was subsequently applied to authentic samples previously screened by a routine HPLC method with diode array detection (DAD).     

Determination of pesticides in water samples by solid phase extraction and gas chromatography tandem mass spectrometry

A multiresidue method for the determination of more than 80 pesticides in water has been developed and validated. The proposed method is based on SPE followed by GC coupled to MS/MS. Different variables affecting SPE procedure, such as cartridges, sample volume and solvents were studied, and mass spectrometric conditions were optimised in order to increase selectivity and sensitivity. Calibration curves were linear over the range of 0.03-0.5 microg/L. Recoveries were in the range of 70-110% and repeatability was below 20% for the lowest calibration point. LODs ranged from 0.001 to 0.025 microg/L and LOQs from 0.003 to 0.076 microg/L. Finally, the method was successfully applied to the analysis of water samples from southeast of Spain.     

On-line solid phase extraction LC-MS/MS analysis of pharmaceutical indicators in water: A green alternative to conventional methods

A method using automated on-line solid phase extraction (SPE) directly coupled to liquid chromatography/tandem mass spectrometry (LC-MS/MS) has been developed for the analysis of six pharmaceuticals by isotope dilution. These selected pharmaceuticals were chosen as representative indicator compounds and were used to evaluate the performance of the on-line SPE method in four distinct water matrices. Method reporting limits (MRLs) ranged from 10 to 25 ng/L, based on a 1 mL extraction volume. Matrix spike recoveries ranged from 88 to 118% for all matrices investigated, including finished drinking water, surface water, wastewater effluent and septic tank influent. Precision tests were performed at 50 and 1000 ng/L with relative standard deviations (RSDs) between 1.3 and 5.7%. A variety of samples were also extracted using a traditional off-line automated SPE method for comparison. Results for both extraction methods were in good agreement; however, on-line SPE used approximately 98% less solvent and less time. On-line SPE coupled to LC-MS/MS analysis for selected indicators offers an alternative, more environmentally friendly, method for pharmaceutical analysis in water by saving time and costs while reducing hazardous waste and potential environmental pollution as compared with off-line SPE methods.     

Determination of alkylphenol and alkylphenolethoxylates in biota by liquid chromatography with detection by tandem mass spectrometry and fluorescence spectroscopy

A quantitative method for the simultaneous determination of octylphenol, nonylphenol and the corresponding ethoxylates (1 to 5) in biota is presented. Extraction methods were developed for egg and fish matrices based on accelerated solvent extraction followed by a solid-phase extraction cleanup, using octadecylsilica or aminopropyl cartridges. Identification and quantitation were accomplished by liquid chromatography-electrospray tandem mass spectrometry (LC-MS-MS) and compared to the traditional liquid chromatography with fluorescence spectroscopy detection. LC-MS-MS provides high sensitivity and specificity required for these complex matrices and an accurate quantitation with the use of 13C-labeled internal standards. Quantitation limits by LC-MS-MS ranged from 4 to 12 ng/g in eggs, and from 6 to 22 ng/g in fish samples. These methods were successfully applied to osprey eggs from the Chesapeake Bay and fish from the Great Lakes area. Total levels found in osprey egg samples were up to 18 ng/g wet mass and as high as 8.2 microg/g wet mass in the fish samples.     

Analysis of linear alkylbenzene sulfonate homologues in environmental water samples by mixed admicelle-based extraction and liquid chromatography/mass spectrometry

Hemimicelles and admicelles of cetyltrimethylammonium bromide (CTAB) and cetylpyridinium chloride (CPC), adsorbed onto silica, were tested as sorbents for the solid phase extraction (SPE) of linear alkylbenzene sulfonate (LAS) homologues from environmental water samples. LASs were quantitatively retained on both surfactants due to high hydrophobic and ionic interactions, which led to the formation of analyte-extractant mixed aggregates. Parameters affecting the SPE of LASs were optimised. Recoveries of analytes from wastewater influent and effluent and river water samples ranged between 86 and 110%. Combination of SPE with liquid chromatography/mass spectrometry provided detection limits for the different LAS homologues of about 4 ng L(-1). The precision of the method, expressed as relative standard deviation, ranged from 5 to 9%. The method was applied to the analysis of LASs in wastewater and river samples using sample volumes between 10 and 25 mL. The LAS concentrations found ranged from 9 to 503 microg L(-1). No cleaning step was required to get accurate results.     

Sensitive determination of acidic drugs and triclosan in surface and wastewater by ion-pair reverse-phase liquid chromatography/tandem mass spectrometry

A new method is presented for the determination of 12 acidic pharmaceuticals (non-steroidal anti-inflammatory drugs and bezafibrate), including two metabolites from aqueous samples, together with triclosan as a personal care product. Ion-pair liquid chromatography (IP-LC) with electrospray ionisation tandem mass spectrometry (ESI-MS) in the negative ion mode was employed. The ion-pairing agent (tri-n-butylamine) increased the signal intensity for all acidic analytes and detection limits of 6-200 ng/L were obtained by multiple reaction monitoring. This allows analysis of wastewater samples by direct injection into the LC/MS system without the need for a preceding enrichment step. When combined with a solid-phase extraction (SPE) step, limits of quantification between 0.15 and 11 ng/L were obtained from 100-mL sample volumes, which is adequate for most applications. The occurrence of matrix effects was studied and standard addition was required for reliable quantification after SPE from wastewater. The method was finally applied to surface and wastewaters, with analyte concentrations ranging from below the detection limit up to 5.5 microg/L.     

Cigarette filter as sorbent for on-line coupling of solid-phase extraction to high-performance liquid chromatography for determination of polycyclic aromatic hydrocarbons in water

An on-line solid-phase extraction (SPE) protocol using the cigarette filter as sorbent coupled with high-performance liquid chromatography (HPLC) was developed for simultaneous determination of trace naphthalene (NAPH), phenanthrene (PHEN), anthracene (ANT), fluoranthene (FLU), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), and benzo(ghi)perylene (BghiP) in water samples. To on-line interface solid-phase extraction to HPLC, a preconcentration column packed with the cigarette filter was used to replace a conventional sample loop on the injector valve of the HPLC for on-line solid-phase extraction. The sample solution was loaded and the analytes were then preconcentrated onto the preconcentration column. The collected analytes were subsequently eluted with a mobile phase of methanol-water (95:5). HPLC with a photodiode array detector was used for their separation and detection. The detection limits (S/N = 3) for preconcentrating 42 mL of sample solution ranged from 0.9 to 58.6 ng L(-1) at a sample throughput of 2 samples h(-1). The enhancement factors were in the range of 409-1710. The developed method was applied to the determination of trace NAPH, PHEN, ANT, FLU, BbF, BkF, BaP and BghiP in local river water samples. The recoveries of PAHs spiked in real water samples ranged from 87 to 115%. The precisions for nine replicate measurements of a standard mixture (NAPH: 4.0 microg L(-1), PHEN: 0.40 microg L(-1), ANT: 0.40 microg L(-1), FLU: 2.0 microg L(-1), BbF: 1.6 microg L(-1), BkF: 2.0 microg L(-1), BaP: 2.0 microg L(-1), BghiP: 1.7 microg L(-1)) were in the range of 1.2-5.1%.     

Determination of propiverine and its metabolites in rat samples by liquid chromatography-tandem mass spectrometry

A liquid chromatography-tandem mass spectrometric (LC-MS-MS) method was developed and validated for the determination of the anticholinergic and antimuscarinc drug propiverine and eight of its metabolites in serum, urine, faeces and different tissue samples of rats. Samples containing propiverine and its metabolites in serum and urine and in the supernatants of faeces and tissue homogenates were extracted and cleaned up using an automated solid phase extraction (SPE) method. An external calibration was used. The analytes were measured employing the multiple reaction monitoring mode (MRM). A sufficient response over the range of 10-1000 ng/ml was demonstrated. The lower limit of quantification of the nine substances was 10 ng/ml. The presented method is suitable for pharmacokinetic or toxicokinetic studies. To look for additional unknown metabolites, the LC-MS-MS system operated in the precursor ion mode using typical product ions of propiverine and of its metabolites. With the help of the chromatographic behaviour and typical fragment ions of the unknown metabolites, it was possible to elucidate their structure. Five until now unknown metabolites were found in the urine and faeces samples. However, without reference substances, a quantification of these analytes was not possible.     

Determination of oxygenated polycyclic aromatic hydrocarbons in atmospheric aerosol samples by liquid chromatography-tandem mass spectrometry

In this paper, the development of an analytical method using liquid chromatography-tandem mass spectrometry (LC-MS-MS) with atmospheric pressure chemical ionization (APCI) for the determination of 17 oxygenated polycyclic aromatic hydrocarbons (OPAH) is described. These OPAH include ketones, pyrones and diketones. The APCI interface parameters have been optimized for maximum sensitivity. Positive ion mode was proved to be most sensitive for ketones and pyrones while negative ion mode gave better detection limits for target diketones. The detection limits of the method ranged from less than 1.20microg L(-1) for several OPAH solutions (between 0.10 and 0.70microg L(-1) for positive mode and between of 0.19 and 1.20microg L(-1) for negative mode). The analytical method was applied particulate matter (PM(2.5)) samples collected over 24-48h periods between March 2005 and June 2005 in Tempe (Arizona, USA). Before analysis aerosol samples were solvent extracted and concentrated to a final volume of 1mL of methanol. OPAH concentrations observed for this urban site ranged from 0.22 to 3.60ngm(-3).     

Simultaneous determination of t,t-muconic, S-phenylmercapturic and S-benzylmercapturic acids in urine by a rapid and sensitive liquid chromatography/electrospray tandem mass spectrometry method

We describe a rapid and sensitive high-performance liquid chromatography/electrospray tandem mass spectrometry (HPLC/ESI-MS/MS) method for simultaneous determination of the most relevant metabolites of benzene and toluene, t,t-muconic acid (t,t-MA), S-phenylmercapturic acid (S-PMA), and S-benzylmercapturic acid (S-BMA). Urine samples were purified before analysis by solid-phase microextraction (SPE) on SAX cartridges with 50 mg sorbent mass. The developed method fulfils all the standard requirements of precision and accuracy. Calibration curves were linear within the concentration range of the standards (0-80 microg/L(urine) for t,t-MA, and 0-25 microg/L(urine) for S-PMA and S-BMA), and had correlation coefficients > or =0.997. Limits of detection were 6.0 microg/L for t,t-MA, 0.3 microg/L for S-PMA, and 0.4 microg/L for S-BMA. The method was used to determine t,t-MA, S-PMA and S-BMA levels in urine of 31 gasoline-station workers, with personal monitoring data obtained from radial symmetry passive diffusive samplers. In the context of mean work-shift exposures of 75.9 microg/m(3) (range 9.4-220.2) for benzene and 331.9 microg/m(3) (78.2-932.1) for toluene, metabolite concentrations in end-of-shift urine samples ranged from 23.5-275.3 microg/g(creatinine) for t,t-MA, non-detectable to 0.9 microg/g(creatinine) for S-PMA, and 3.8-74.8 microg/g(creatinine) for S-BMA. No significant correlation was found between the environmental concentrations and urinary metabolites (p > 0.05 for all cases); the ratios of benzene metabolites could be influenced by exposure levels and co-exposure to xylenes and toluene. The high throughput of this procedure should facilitate exploration of the metabolic effects of benzene-related co-exposure to toluene and alkylbenzenes in large populations of subjects exposed to gasoline.     

Simultaneous determination of isoflavones and lignans at trace levels in natural waters and wastewater samples using liquid chromatography/electrospray ionization ion trap mass spectrometry

A high-performance liquid chromatography/electrospray ionization ion trap mass spectrometry (HPLC/ESI-MSn) method has been developed for the trace determination of phytoestrogens in aquatic environmental samples. The method includes solid-phase extraction (SPE) and analysis using liquid chromatography/electrospray ionization ion trap mass spectrometry. The aquatic environmental samples, influent of a wastewater treatment plant (WWTP) and creek water, were adjusted to pH approximately 5 before extraction. The analyzed phytoestrogens were identified by an MSn method and quantified against a deuterated internal standard (genistein-3',5',6,8-D4). In negative ion mode, 0.1% formic acid was employed in acetonitrile/water mobile phase. The method detection limits ranged from 0.5 to 10 ng/L in WWTP influent and from 0.1 to 5 ng/L in creek water. Average SPE recoveries for the analyzed phytoestrogens ranged from 85 to 95%, with a relative standard deviation (RSD) (%) ranging from 3.9 to 6.5. The concentrations of the six analyzed phytoestrogens varied from 0.2 to 600 ng/L with high levels of enterolignans (enterolactone and enterodiol) found in the collected wastewater. The method is shown to be suitable for the determination of phytoestrogens in aquatic environmental samples at nano- and sub-nanogram per liter levels.     

Simultaneous extraction of tetracycline, macrolide and sulfonamide antibiotics from agricultural soils using pressurised liquid extraction, followed by solid-phase extraction and liquid chromatography-tandem mass spectrometry

The veterinary antibacterial agents chlortetracycline (CTC), oxytetracycline (OTC), sulfadiazine (SDZ), erythromycin (ERY) and tylosin (TYL A, B, C and D) were extracted from soil using pressurized liquid extraction (PLE). Citric acid (pH 4.7) and methanol was used as extraction buffer, followed by tandem-solid-phase extraction (SPE) clean-up (SAX + HLB) for all compounds. For quantification two slightly different methods were employed using LC-MS-MS with MRM detection. The soil extraction method was validated using a loamy sand soil and a sandy soil, representing two typical Danish agricultural soils. Recoveries were 50-80% for the tetracyclines (CTC and OTC) and sulfadiazine (SDZ) and 60-100% for the macrolides (TYL and ERY). Limits of detection for the soil extraction method (LOD(soil)) were 0.6-5.6 microg kg(-1) soil for CTC and OTC, 0.9-2.9 microg kg(-1) soil for SDZ and 2.4-5.5 microg kg(-1) soil for TYL A and ERY. Furthermore, the method was applied to field samples taken from two agricultural fields fertilised with liquid manure containing CTC and TYL A. These results showed a decline in the content of antibacterial agents throughout the sampling period of 155 days from 10 to 15 microg CTC kg(-1) soil and 20-55 microg TYL A kg(-1) soil to below or near the LOD(soil) listed above. Finally, the method was applied to barley grains harvested from the fields. None of the antibacterial agents were measured in grain samples, but recoveries for spiked grain samples were similar to soil recoveries.     

Detection and identification of phenazone-type drugs and their microbial metabolites in ground and drinking water applying solid-phase extraction and gas chromatography with mass spectrometric detection

A new analytical method applying in situ derivatization was developed to enable the extraction of polar drug metabolites from water samples by solid-phase extraction (SPE). An additional derivatization by silylation was used to enhance the sensitivity of analyte detection by gas chromatography-mass spectrometry (GC-MS). Thus, the two metabolites 1,5-di-methyl-1,2-dehydro-3-pyrazolone (DP) and 4-(2-methylethyl)-1,5-dimethyl-1,2-dehydro-3-pyrazolone (PDP), postulated for the degradation of phenazone and propyphenazone, were identified and detected up to the microg/L level in raw and drinking water samples from public water supply.     

Comparison of a non-aqueous capillary electrophoresis method with high performance liquid chromatography for the determination of herbicides and metabolites in water samples

A method of capillary electrophoresis (CE) for the determination of triazine herbicides and some of their main metabolites in water samples has been developed. The proposed CE method includes an off-line solid-phase extraction (SPE) procedure with LiChrolut EN sorbent coupled to a non-aqueous capillary electrophoresis (NACE) separation with UV detection. The target compounds were the chloro-s-triazines simazine, atrazine, propazine; the methyltio-s-triazines ametryn and prometryn and three main derivatives from the atrazine degradation products; namely, deethylatrazine, deethylhydroxyatrazine and deisopropylhydroxyatrazine. The analytical characteristics of the CE method are reported. The repeatability of the method was studied considering the different steps of the method separately in order to determine the contributions of each step to the total variability of the method. The NACE-UV results are compared with those obtained with a high performance liquid chromatography with UV detection (HPLC-UV) method. The same off-line SPE procedure was applied to both techniques. The results obtained show that both methods afford the same results in the analysis of surface and drinking water samples, with a level of significance regarding the F- and t-tests greater than 0.05 in all the cases. The detection limits in surface water samples were in the 0.04-0.32 microg l(-1) and 0.11-1.2 microg l(-1) ranges for the NACE-UV and HPLC-UV methods, respectively. The recoveries (spiked/found) were significantly 100% in all cases.     

Polycyclic aromatic hydrocarbon analysis in different matrices of the marine environment

Polycyclic aromatic hydrocarbons (PAHs) were determined in marine samples of various types, i.e. seawater, sediment and mussel homogenate samples. The samples were spiked with standard PAH mixtures in both polar (acetonitrile) and non-polar (i-octane) solvents, then extracted. Extraction from seawater was performed by liquid/liquid extraction to hexane (LLE) and with solid phase extraction (SPE) discs. The water samples were filtered and unfiltered seawater, and redistilled water for comparison. The discs with PAHs adsorbed from water samples, and also the sediment and mussel homogenate samples, were extracted with acetonitrile by sonication. PAHs in the disc extracts and from the LLE were cleaned-up using TLC and next determined by GC/MS/IT (with ion-trap) and HPLC-DAD/UV. The analytical procedures were verified with deuterated PAH standard mixtures. The large differences in PAH recoveries (from 12 to 86% for sum, and from 3 to 135% for particular PAHs) do not depend solely on the type of matrix and analytical procedure applied (e.g. standard solvent, volume of evaporated sample), but also on the concentration and molecular structure of the analyte. Usually, only a fraction of each PAH content in the matrix is determined, depending on the particulate matter in seawater and the sorption properties of the solid matrix. The recoveries of deuterated PAHs are higher than those of non-deuterated compounds.     

Simultaneous determination of 20 beta-agonists in pig muscle and liver by high-performance liquid chromatography/tandem mass spectrometry

A method was developed to determine 20 illegal residual beta-agonists in pork tissues, including muscle and liver simultaneously. The samples were hydrolyzed by beta-glucuronidase, purified by PCX SPE cartridges, and detected by HPLC coupled with electrospray ionization MS/MS operating in the positive ion mode. Matrix-fortified calibration was performed to compensate for the matrix effect and loss in sample preparation. Decision limit ranged from 0.05 to 0.23 microg/kg in muscle and 0.05 to 0.57 microg/kg in liver. Decision capacity ranged from 0.11 to 0.4 microg/kg in muscle and 0.16 to 0.79 microg/kg in liver. In Food Analysis Performance Assessment Scheme proficiency test 0287, a pig liver test material containing 13 beta-agonists was analyzed using the method developed, and clenbuterol and ractopamine were confirmed as being present. Z-scores for clenbuterol and ractopamine were 0.2 and 0.6, respectively.     

Coupled-column liquid chromatography combined with postcolumn photochemical derivatization and fluorescence detection for the determination of herbicides in groundwater

This study examines the application of coupled-column LC-photochemically induced fluorimetry-fluorescence detection (LC-LC-PIF-FD), demonstrating its potential for the quantitative and selective detection of six herbicides, including propanil and the phenylureas monuron, monolinuron, chlorotoluron, diuron and neburon in groundwater samples. An AQUASIL C18 50 x 4.6 mm(2) id column coupled to an AQUASIL C18 150 x 4.6 mm(2) id column for analyte clean-up and determination were used, respectively. A simple SPE with Cl8 cartridges was carried out, yielding average recoveries between 80 and 112% (n = 6) with RSDs between 0.5 and 9%. The LODs ranged from 0.0083 to 0.0833 microg/L in the groundwater samples.     

固相微萃取-气相色谱法和气相色谱-质谱法测定茶叶中氟虫腈及其代谢物残留

基于固相微萃取-气相色谱(SPME-GC)建立了检测茶叶中氟虫腈及其代谢物(脱亚硫酰基氟虫腈、硫化氟虫腈、氟虫腈砜、酰胺氟虫腈)残留的分析方法。实验中采用85 μm聚丙烯酸酯(PA)萃取头,萃取温度为60 ℃,萃取缓冲体系的pH值为9。当添加水平为2～10 μg/kg时,回收率在71.2%～109.3%之间,相对标准偏差(RSD)在1.2%～7.1%之间。方法的检出限(LOD)和定量限(LOQ)分别在0.3～1.2 μg/kg和1.0～4.0 μg/kg之间。对所建立的方法采用气相色谱-质谱(GC-MS)进行确证,结果令人满意。本方法灵敏度、精密度和LOD均符合残留分析要求,具有快速、灵敏度高的特点,适合于茶叶中氟虫腈及其代谢物残留的痕量分析。     

Sensitive determination of deuterated and non-deuterated indole-3-acetic acid and 5-hydroxyindole-3-acetic acid by combined capillary gas chromatography-negative-ion chemical ionization mass spectrometry

Sensitive methods for the determination of deuterated and non-deuterated indole-3-acetic acid and 5-hydroxyindole-3-acetic acid by combined capillary gas chromatography-negative-ion chemical ionization mass spectrometry were developed. Indole-3-acetic and 5-hydroxyindole-3-acetic acids were converted into pentafluorobenzyl and trifluoroacetylmethyl derivatives, respectively, after pre-purification by high-performance liquid chromatography. These derivatives were separated by gas chromatography and determined by selected ion monitoring. In the determinations, indole-3-acetic-2,2,2',4',5',6',7'-d7 acid and 5-hydroxyindole-3-acetic-3,3-d2 acid were used as internal standards. The methods developed in this work were used for the determination of deuterated and non-deuterated indole-3-acetic acid and 5-hydroxyindole-3-acetic acid in human urine samples collected before and after administration of L-tryptophan-3,3-d2.