Temperature Dependence in the Synthesis of SBA-16-Type Mesoporous Silica with Pluronic F68 Block Copolymer

By adjusting the local effective surfactant packing parameter through synthesis temperature, highly ordered SBA-16-type mesoporous silica materials have been synthesized by templating with a nonionic triblock copolymer Pluronic F68 in strongly acidic conditions at temperature 30～40°C with the addition of K₂SO₄. The prepared SBA-16-type mesoporous silica materials having Im3m cubic mesostructure were proved by the well-defined x-ray diffraction patterns combined with transmission electron microscopy. Scanning electron microscopy indicated that a transformation from faced-sphere to faced-polyhedron shape morphologies could be induced with increasing of the synthesis temperature. The nitrogen adsorption–desorption analysis revealed that the mean pore size (5.50～6.13 nm) of the prepared materials increased with increasing synthesis temperature. However, when the synthesis temperature exceeded 46°C, only disordered mesoporous silca was obtained. Our synthesis strategies by adjusting the local effective surfactant packing parameter through synthesis condition, even in a narrow range, would be used not only to optimize the synthesis conditions of reported mesoporous silca, but also to fabricate new mesoporous silica materials with well-ordered channel and anticipated morphologies.     

pH对两步法非离子模板合成MSU-X类硅基介孔结构的影响

采用两步法以非离子型表面活性剂Tween 20为模板剂合成硅基介孔材料, 研究了pH对介孔材料结构的影响. 结果表明, 没有氟离子存在且模板剂浓度较低(约为2%(w))的条件下, 在弱酸性环境中(pH=3.32-4.26)可以制备有序的MSU-X类硅基介孔材料, 本研究中的简单合成体系有助于查明MSU-X合成机理. 对所得介孔材料测试表明, 在同样的合成体系中, 随着体系pH的变化, 所得硅基介孔材料的形貌和孔壁结构都发生了变化.     

酸诱导介观相转变硅基介孔材料的合成机理及其改性

采用两步法以三嵌段共聚物P104(PEO27-PPO61-PEO27)为模板剂合成介孔材料, 研究了介孔材料结构随体系pH 值的变化, 探讨了体系中介观相转变的机理. 研究表明,随着pH 的升高, 发现体系中无机物种和模板剂所组成的介观相发生了转变,由P6mm 的SBA-15(pH=1.51-2.67)2D六角孔道结构转变为3D 蠕虫状孔道的MSU-X(pH=3.93-4.56)结构. 对所得的两种不同种类的硅基材料以γ-胺丙基三乙氧基硅烷(APTES: NH2(CH2)3Si(C2H5O)3)进行表面烷基化改性结果表明, 在同样的条件下, 经过改性后MSU-X类介孔材料孔壁上接枝的烷基数目要远超过SBA-15 类介孔材料.     

Preparation of ordered mesoporous SiC from preceramic polymer templated by nanoporous silica

Highly ordered mesoporous SiC materials were prepared by infiltrating viscous liquid preceramic polymer, allylhydridopolycarbosilane, into two types of surface modified nanoporous silica templates: mesoporous silica SBA-15 and mesocellular siliceous foam. The silica templates were subsequently etched off after pyrolysis at 1000 degrees C under nitrogen atmosphere with the resultant formation of ordered mesoporous structures. The mesoporous SiC materials, synthesized from both types of templates possessed high Brunauer-Emmett-Teller (BET) surface areas in the range of 250-260 m(2)/g with pore sizes of 3.4-3.6 nm. The ordered structures of mesoporous SiC were exact inverse replicas of their respective silica templates, as characterized by small angle X-ray diffraction (XRD), transmission electron microscope (TEM) images, and the adsorption-desorption isotherm of nitrogen.     

由纳米晶前驱体组装有序介孔silicalite-1分子筛

采用两步法将不同尺寸的silicalite-1分子筛纳米晶种通过自组装合成了一系列有序介孔silicalite-1分子筛。首先将强碱性的silicalite-1前驱体分别加热不同时间得到纳米晶种,然后在类似合成SBA-15的强酸性条件下组装成有序的介孔材料。合成条件的剧烈变化阻止了分子筛晶种的继续长大,并在三嵌段共聚物模板的诱导下组装成有序介孔材料。这种“自下而上”的方法制备有序介孔分子筛同时包含微孔和介孔。氮气吸脱附结果表明所制备的介孔分子筛材料均表现了很大的比表面积(730 m2/g以上)。     

SBA-15负载CeO2纳米晶的溶胶-凝胶一步合成

以P123为模板剂, 正硅酸乙酯和硝酸铈为前驱体, 通过溶胶-凝胶路线在酸性条件下合成了SBA-15负载氧化铈(CeO2与SiO2质量比为28.7%)有序介孔材料. 采用热重/差热分析(TGA/DTA)、X射线衍射(XRD)、透射电镜(TEM)和氮气吸附等手段对所合成材料进行了表征. 结果表明, 合成的材料具有类似于SBA-15的结构, 孔径、孔容和比表面积分别为38.7 Å, 0.46 cm3/g和570 m2/g. X射线衍射(XRD)、透射电镜(TEM)、X射线能谱(EDS)和选区电子衍射花样联合表征证实了铈物种以高分散的CeO2纳米晶的形式分布在介孔基体中.     

Synthesis and characterization of surface modified SBA-15 silica materials and their application in chromatography

Hexagonally ordered SBA-15 mesoporous silica spheres with large uniform pore diameters are obtained using the triblock copolymer, Pluronic P123, as template with a cosurfactant cetyltrimethylammonium bromide (CTAB) and the cosolvent ethanol in acidic media. A series of surface modified SBA-15 silica materials is prepared in the present work using mono- and trifunctional alkyl chains of various lengths which improves the hydrothermal and mechanical stability. Several techniques, such as element analysis, nitrogen sorption analysis, small angle X-ray diffraction, scanning electron microscopy (SEM), FTIR, solid-state (29)Si and (13)C NMR spectroscopy are employed to characterize the SBA-15 materials before and after surface modification with the organic components. Nitrogen sorption analysis is performed to calculate specific surface area, pore volume and pore size distribution. By surface modification with organic groups, the mesoporous SBA-15 silica spheres are potential materials for stationary phases in HPLC separation of small aromatic molecules and biomolecules. The HPLC performance of the present SBA-15 samples is therefore tested by means of a suitable test mixture.     

Facile method to synthesize platelet SBA-15 silica with highly ordered large mesopores

Highly ordered mesoporous SBA-15 silica with large pore diameter of 18 nm (nominal BJH pore diameter ~22 nm) and short pore length (~500 nm) was synthesized using a micelle expander 1,3,5-triisopropylbenzene in the absence of ammonium fluoride by employing short initial stirring time at 17 °C followed by static aging at low temperature. Scanning and transmission electron microscopies revealed that the material comprised of platelet particles in which large mesopores were nearly flawlessly arranged within uniform domains up to 3 μm in size. The platelet SBA-15 had the (100) interplanar spacing of 17 nm, high surface area (~470 m(2) g(-1)) and large pore volume (~1.6 cm(3) g(-1)). The hydrothermal treatment at 130 °C for 2 days was employed to eliminate constrictions from the pore channels. The control experiment showed that a sample prepared with prolonged stirring had very similar mesoporous properties, but the particle size was smaller and the domains were irregular, proving that the static conditions facilitate the formation of SBA-15 with platelet particle morphology. The absence of ammonium fluoride was also critical in attaining the platelet particle shape.     

介孔分子筛SBA-15作为高效液相色谱固定相分离维生素E

以三嵌段共聚物P123聚环氧乙烷-聚环氧丙烷-聚环氧乙烷(PEO-PPO-PEO)为模板,在强酸性(1.6mol/L HCl)条件下,水热合成了棒状二维六方有序介孔材料SBA-15.粒径棒长约1～1.5μm,直径为400～500nm,平均孔径5.8nm,BET比表面积799㎡/g.并用合成的SBA-15作为正相高效液相...     

Effects of Morphology and Structural Characteristics of Ordered SBA-15 Mesoporous Silica on Release of Ibuprofen

Three kinds of highly ordered SBA-15 mesoporous materials with different pore sizes and morphologies denoted as LPS-SBA-15 (stick-like with pore size 7.28 nm), CPS-SBA-15 (stick-like with pore size 5.96 nm) and T-SBA-15 (tablet-like with pore size 4.64 nm) have been prepared, characterized and employed as carrier materials. The release behaviors of the ibuprofen in a simulated body fluid from these mesoporous silica materials were studied. The influences of pore size and exterior morphologies of mesoporous silica on the release behaviors of ibuprofen have been investigated. It has been found that the release becomes fast with increasing of pore size and slow with extending of transport pathway, and that the release rate of ibuprofen from the three kinds of SBA-15 is LPS-SBA-15 > T-SBA-15 > CPS-SBA-15. The results show that the inner structure as well as the exterior morphologies of SBA-15 mesoporous silica can seriously affect the release behaviors of ibuprofen.     

Synthesis of chiral mesoporous silicas with oligo(saccharide) surfaces and their use in separation of stereoisomers

Novel chiral mesoporous silicas (SBA-15 motif) with chemically bonded oligo(saccharides) (1, 3, and 7 glucose units) were obtained through the cocondensation of organosilicon derivatives of the oligo(saccharides) and silica precursors in the presence of polymer surfactant template under mild acidic conditions. The pore order and structure of the materials prepared were characterized by transmission electron microscopy and nitrogen adsorption. The direct application of the oligo(saccharide)-grafted SBA-15 stationary phases in the HPLC separations of stereoisomers was demonstrated for the first time.     

Controlled growth of mesostructured crystalline iron oxide nanowires and Fe-filled carbon nanotube arrays templated by mesoporous silica SBA-16 film

The three-dimensional (3D) accessible pore structures (Imm space groups) of continuous mesoporous silica SBA-16 thin films have been prepared by a dip-coating technique in nonaqueous media under acidic conditions on indium-tin oxide glass (ITO). The films are oriented with the (111) crystal plane perpendicular to the surface of the film. On one hand, deposition of iron metal into the mesopores of SBA-16 films was achieved by using an electrochemical method. The Fe2O3 nanowire arrays were synthesized. The crystalline structures of porous Fe2O3 nanowires and nanorods were studied via TEM, SEM, and XRD. On the other hand, a small amount of Fe was deposited into the pores of the SBA-16 thin film as a catalyst, and carbon nanotube arrays formed inside the pores of SBA-16 film were fabricated by catalytic decomposition of acetylene at 700 degrees C. The second-order template synthesis method for preparing the ordered array of carbon nanotubes filled with Fe has been used. The carbon nanotubes are very uniform in diameter and length and are aligned vertically with respect to the SBA-16 film.     

Thermal stability of high surface area silicon carbide materials

The synthesis of mesoporous silicon carbide by chemical vapor infiltration of dimethyl dichlorosilane into mesoporous silica SBA-15 and subsequent dissolution of the silica matrix with HF was investigated. The influence of the synthesis parameters of the composite material (SiC/SBA-15) on the final product (mesoporous SiC) was determined. Depending on the preparation conditions, materials with specific surface areas from 410 to 830 m² g⁻¹ and pore sizes between 2 and 10 nm with high mesopore volume (0.31-0.96 cm³ g⁻¹) were prepared. Additionally, the thermal stability of mesoporous silicon carbide at 1573 K in an inert atmosphere (argon) was investigated, and compared to that of SBA-15 and ordered mesoporous carbon (CMK-1). Mesoporous SiC has a much higher thermal textural stability as compared to SBA-15, but a lower stability than ordered mesoporous carbon CMK-1.     

Preparation and catalytic performances of ultralarge-pore TiSBA-15 mesoporous molecular sieves with very high Ti content

Highly ordered TiSBA-15 mesoporous molecular sieves with different nSi/nTi ratios and tunable pore diameters have been prepared through direct synthesis under various hydrochloric acid concentrations and synthetic temperatures. The structure and the textural parameters of the materials were investigated by powder X-ray diffraction and nitrogen adsorption/desorption measurements. Decrease of the acid concentration and nSi/nTi ratio in the synthetic gel enhanced the amount of Ti incorporation in SBA-15 materials without affecting their structural order and textural parameters. Highly ordered mesoporous TiSBA-15 with a very high Ti content up to a nSi/nTi ratio of 1.9 was prepared for the first time under the optimized synthesis conditions. Control of synthetic temperature resulted in tuning of pore geometries without structural deterioration and Ti content. Ultralarge-pore TiSBA-15 with a pore size of 12.6 nm and a pore volume of 1.3 cm3 g-1 was also synthesized. The nature and the coordination of the Ti atoms in SBA-15 prepared under various synthesis conditions were investigated by UV-vis spectroscopy. It has been found that the Ti atoms are well-dispersed and mostly occupy the tetrahedral coordination under the optimized synthesis conditions. Catalytic performance of the obtained TiSBA-15 materials was also investigated through oxidation of styrene by hydrogen peroxide and tert-butylhydroperoxide as oxidants.     

Effect of synthesis conditions on the mesoscopical order of mesoporous silica SBA-15 functionalized by amino groups

Mesoporous amine-functionalized SBA-15 silica has been synthesized directly by the co-condensation of tetraethyl orthosilicate (TEOS) and aminopropyl-trimethoxysilane (APTMS) under acidic conditions with an APTMS/(APTMS + TEOS) molar ratio of 10%. The effect of synthesis conditions, including TEOS pre-hydrolysis, as well as the heating temperature and time, on the mesoscopical order and pore structure of the functionalized SBA-15 have been studied in detail by means of powder X-ray diffraction, nitrogen sorption, transmission electron microscopy, infrared spectra and solid state ²⁹Si nuclear magnetic resonance. A functionalized SBA-15 silica with a highly ordered two-dimensional P6 mm hexagonal symmetry and a narrow pore size distribution centered at 6 nm can be obtained if TEOS is allowed to pre-hydrolyze for 2 h. For the sample with TEOS pre-hydrolysis time of 4 h, aging at 50°C or 150°C leads to a more ordered pore arrangement compared to 100°C and also a narrower pore size distribution with larger pore volume. Increasing aging time is in favor of the formation of mesoscopically ordered structure, but fails to obtain a superior pore structure.     

改性中孔分子筛SBA-16薄膜的合成及表征

在酸性条件下, 以导电玻璃(ITO)为基底合成了SBA-16分子筛膜. 所制备的SBA-16膜孔径均匀, 具有体心立方结构(属于Im3m空间群), SBA-16膜的晶胞参数为18.6 nm. TEM, SEM和XRD等技术研究表明, 加入少量的AlCl₃盐于形成膜的母液并且采用RSiX₃对导电玻璃基底进行处理, 能够明显改善SBA-16膜的连续性而不影响孔结构. 红外(FTIR)研究结果表明, SBA-16膜的表面硅羟基和结晶水很少, 膜很稳定. XPS研究表明, 加入少量MnCl₂对SBA-16膜进行改性, 可以提高膜的导电性.     

Synthesis of mesoporous carbons using ordered and disordered mesoporous silica templates and polyacrylonitrile as carbon precursor

Mesoporous carbons were synthesized from polyacrylonitrile (PAN) using ordered and disordered mesoporous silica templates and were characterized using transmission electron microscopy (TEM), powder X-ray diffraction, nitrogen adsorption, and thermogravimetry. The pores of the silica templates were infiltrated with carbon precursor (PAN) via polymerization of acrylonitrile from initiation sites chemically bonded to the silica surface. This polymerization method is expected to allow for a uniform filling of the template with PAN and to minimize the introduction of nontemplated PAN, thus mitigating the formation of nontemplated carbon. PAN was stabilized by heating to 573 K under air and carbonized under N2 at 1073 K. The resulting carbons exhibited high total pore volumes (1.5-1.8 cm3 g(-1)), with a primary contribution of the mesopore volume and with relatively low microporosity. The carbons synthesized using mesoporous templates with a 2-dimensional hexagonal structure (SBA-15 silica) and a face-centered cubic structure (FDU-1 silica) exhibited narrow pore size distributions (PSDs), whereas the carbon synthesized using disordered silica gel template had broader PSD. TEM showed that the SBA-15-templated carbon was composed of arrays of long, straight, or curved nanorods aligned in 2-D hexagonal arrays. The carbon replica of FDU-1 silica appeared to be composed of ordered arrays of spheres. XRD provided evidence of some degree of ordering of graphene sheets in the carbon frameworks. Elemental analysis showed that the carbons contain an appreciable amount of nitrogen. The use of our novel infiltration method and PAN as a carbon precursor allowed us to obtain ordered mesoporous carbons (OMCs) with (i) very high mesopore volume, (ii) low microporosity, (iii) low secondary mesoporosity, (iv) large pore diameter (8-12 nm), and (v) semi-graphitic framework, which represent a desirable combination of features that has not been realized before for OMCs.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

以离子液体为结构导向剂合成有序超微孔二氧化硅

在酸性条件下, 以1-十六烷基-3-甲基溴化咪唑为表面活性剂合成了具有有序超微孔结构的二氧化硅材料, 所合成的材料具有较高的比表面积和二维六方有序的孔结构, 样品的孔径尺寸为1.8 nm.     

Preparation,characterization, and luminescence of (SBA-15) immobilized pepsin

SBA-15 mesoporous silica was synthesized by hydrothermal method and its surface was methylated by treatment with methyltrimethoxysilane. Pepsin was immobilized on the obtained materials giving host-guest composite materials (SBA-15)-pepsin and (methylated SBA-15)-pepsin. The optimum conditions for preparation of these materials were established. Methylated SBA-15 (M-SBA-15) has improved immobilization efficiency of enzyme compared to initial SBA-15 silica. It was shown that with the gradual increase of NaCl solution ionic strength the immobilized amount of enzyme was reduced. Powder X-ray diffraction and Fourier transform infrared spectroscopy showed that the host frameworks in the prepared host-guest composite materials are intact and the ordered structure was retained. Scanning electron microscopic studies revealed fibrous morphologic characteristics of the SBA-15 and the immobilized pepsin composite materials. The average particle diameter of (SBA-15)-pepsin composite was 338 ± 10 and 343 ± 10 nm for (M-SBA-15)-pepsin. The low temperature N₂ adsorption-desorption study at 77 K showed that the pore sizes and specific surface areas of the host-guest composite materials were smaller than those before the introduction of the enzyme, suggesting that the immobilized enzyme occupied a definite position in the host material pore channels. The UV-vis solid diffuse reflectance and luminescence studies showed that the enzyme was successfully immobilized on to the host material and that after the immobilization of enzyme on SBA-15 the conformation of pepsin macromolecule has not been changed.