Modelling of the phase transition of nanoscale confined liquid crystal

By dividing the bulk melting entropy, a simple thermodynamic model without any adjustable parameter for the size-dependent melting transition temperature has been extended to interpret the melting and freezing transitions of liquid crystals (LCs) confined in nanopores. The results show that as the size of the nanopore decreases, the melting, clearing and freezing transition temperatures of LCs drop. The transition temperatures directly depend on the density of hydrogen bond at the interface between inner pore wall and LC molecules. The model predictions agree well with the corresponding experimental results of LCs p-azoxyanisole and 4-pentyl-4′-cyanobiphenyl confined in nanopores.     

Effects of the fluorinated liquid crystal molecules on the electro-optical properties of polymer dispersed liquid crystal films

The different fluorinated liquid crystal (LC) molecules doped to E8 were used as LC component to prepare polymer dispersed liquid crystal (PDLC) films. The mass fraction of the LC mixture is fixed 50.0 wt%. Results indicate that doping 8.0 wt% fluorinated LC molecule ME3CP to E8 significantly reduced the driving voltage of the PDLC films, and the driving voltage reduced with the rise of mass fraction of ME3CP. Besides, the terminal flexible chain length of the fluorinated LC molecule influenced the LC mixture properties based on E8, such as the dielectric anisotropy, birefringence and viscosity of the LC mixture, and the morphology and the electro-optical properties of PDLC films were controlled not only by the physical properties of the LC mixture, but also by the terminal flexible chain length of the fluorinated LC molecule .     

Effect of terminal aryl rings of liquid crystal trimers on liquid crystalline properties

Liquid crystalline properties of five series of biphenyl derivatives connected with p-nitrophenyl, phenyl, 2-naphthyl, 9-phenathryl and bromo as the terminal groups via flexible spacers were studied. All the compounds exhibited nematic phase. The nematic–isotropic or isotropic–nematic transition properties resulted in an odd–even effect as the length of the spacers was varied, in which the even members exhibited higher values, for the compounds with p-nitrophenyl, phenyl, 2-naphthyl and 9-phenanthryl groups, while the transitional properties of the compounds substituted with bromo atom as the terminal group instead of the aryl groups did not show such odd–even effect. These results suggest that the aryl rings, such as p-nitrophenyl, phenyl, 2-naphthyl and 9-phenanthryl groups, play a role of mesogen while the terminal bromo atom does not. The effect of the terminal aryl rings on the liquid crystalline properties will be reported.     

Sol/gel transition and liquid crystal transition of HPC in ionic liquid

This work uses an ionic liquid (IL), 1-butyl-3-methylimidazolium acetate, as a solvent to study the sol/gel transition (SGT) and liquid crystal transition (LCT) of hydroxypropylcellulose (HPC) solution. The LCT concentration of HPC at room temperature is 7 wt%, which is slightly higher than its SGT concentration of 6 wt%. For HPC concentrations of over 7 wt%, three rheological approaches were utilized, and the parameters relaxation time, hysteresis ratio and loss modulus (G″) are measured to determine the LCT temperature. The relaxation study concludes that the LC-critical concentration of HPC is 7 wt%. When HPC exceeds 7 wt%, the LC transition temperatures, ranging from 45 to 51 °C, can be measured and are proportional to the HPC concentration. The rheological results are then confirmed by making observations under a polarized optical microscope. All results are highly mutually consistent. Most significantly, the rheological parameters adopted herein can be used as good indicators of the LC transition. Of those indicators, G″ changes distinctly at the LCT point, and can thus be suggested to be the most helpful indicator in determining the LCT temperature.     

Effects of functionality of thiol monomer on electro-optical properties of polymer-dispersed liquid crystal films

In this paper, polymer-dispersed liquid crystal (PDLC) films which based on the acrylate and the thiol monomers were first prepared by ultraviolet-initiated polymerisation. The electro-optical properties and morphologies of the PDLC films were systematically investigated. The functionality of thiol monomers and their feed ratio showed great influence on the properties of the fabricated PDLC films because of the existence of competition between thiol–acrylate reaction and acrylate monomer polymerisation reaction. This made the polymer network and electro-optical properties of the PDLC films easily tunable by the introduction of the thiol monomers. When added four-functional thiol monomer PETMP with appropriate concentration into the PDLC system, lower driven voltage and higher contrast ratio were achieved.     

Bipolar to toroidal configuration transition in liquid crystal droplets

Liquid crystal (LC) droplets dispersed in isotropic media are of significant interest for scientific community and great importance for industries. The confinement can generate many fascinating LC director configurations and enable important practical applications. With tangential anchoring condition at the droplet surface, theoretically there are several possible configurations: bipolar, twisted bipolar, escaped toroidal, toroidal and so on. Bipolar configuration is usually observed in droplets made from common LCs while the toroidal configuration is rarely observed and it is hard to create especially in thermotropic LCs. Their realisations depend on the splay, bend and twist elastic constants ratio, and anchoring condition of the LC and polymer interface. We constructed thermotropic LCs with abnormally small bend elastic constants, with which stable toroidal configuration were successfully created. We provide a brand new method to create toroidal droplet by simply varying the bend elastic constant. We observed the transition from bipolar configuration to toroidal configuration. We performed a detailed study of the texture of toroidal droplets.     

Study on the electro-optical properties of polyimide-based polymer-dispersed liquid crystal films

The reflectivity control device, initially developed for attitude control, is utilised to control the solar sail orbit by switching the states between absorption and specular reflection. Actually, the major parts of the device are the polymer-dispersed liquid crystal (PDLC) films. Here, PDLC films based on polyimide (PI) as polymer matrix and a low molecular weight LC can be prepared by the thermally induced phase separation (TIPS) method. The influences of cooling rate and the content of LC on the size and uniformity of LC droplets dispersed in a polymer matrix by a TIPS process were investigated. It was found that a fast cooling rate gave smaller droplet sizes and hence a more uniform distribution as compared to the ones produced under a slow cooling rate. If the LC content was increased, the droplet size would be increased. Furthermore, the effect of LC droplet size on the electro-optical properties of the PI-based PDLC films was discussed, such as transmittance, threshold voltage, driving voltage and contrast ratio (CR).     

The physical properties of alkene-terminated liquid crystal molecules/E8 mixture and the electro-optical properties as they doped in polymer-dispersed liquid crystal systems

Effects of the content of fluorinated alkene-terminated liquid crystal (LC) molecules on the physical properties of the fluorinated alkene-terminated LC/E8 mixture were studied. The morphology and electro-optical properties as they doped in polymer-dispersed liquid crystal (PDLC) films were investigated. The detailed discussion of the obtained results is given. As a result, comparing with the physical properties of the series of LC mixtures with the same content of the analogous fully saturated compounds doped with E8, we find that the birefringence is significantly larger for the LC mixture with the alkene-terminated materials. Both fluorinated alkene-terminated LC molecules and the analogous fully saturated compounds doped with E8 reduce the driving voltage of PDLC films. Moreover, PDLC films with the fluorinated alkene-terminated LC molecules possessed higher contrast ratio and faster response time than that of the PDLC films prepared by adding the same mass fraction of the analogous fully saturated compounds. Thus, the ability to manipulate physical properties of LC mixture and electro-optical properties of PDLC films by changing the LC molecular structures may have future relevance for new LC structures design and applications of PDLC films.     

Effects of silver nanoparticle doping on the electro-optical properties of polymer stabilized liquid crystal devices

ABSTRACT

Polymer stabilised liquid crystal (PSLC) devices are widely used in various smart light modulation occasions. Their electro-optical properties can still be improved to address future challenges. It is well known that doping liquid crystal (LC) materials with nanoparticles can change the material’s electro-optical performance. In this study, silver nanoparticles (AgNPs) with size about 15–20 nm and surfactant were doped into PSLC devices. The effects of AgNPs doping on the PSLC electro-optical performances were studied. The result shows that AgNPs and surfactant doping can increase the dielectric anisotropy of LC mixture. PSLC devices with AgNPs doping have lower driving voltage and response time than un-doped PSLC devices. Therefore, doping of a specific concentration of AgNPs resulted in PSLC devices with improved electro-optical performance.     

Crosslinked liquid crystal polymers from liquid crystal monomers: Synthesis and mechanical properties

Difunctional acrylates and methacrylate monomers have been made which are high order smectic liquid crystal (or crystalline) at room temperature. This report discusses materials with the following structure: F–S–M–S–F, where F is a functional group, acrylate or methacrylate (A or M); S is a spacer (CH₂)_n(n), and M is a mesogen—in this case 4,4′-dioxybiphenyl (B). They are codified as BnA or BnM where n is the number of methylenes in the spacer. High conversion with high T_g can be obtained when polymerizing in the smectic state because the reactive end groups are concentrated in a small volume and can react well with little or no diffusion. B2A, B3A, B6A, B11A, and B3M were polymerized in the smectic state and compared to polymers made at temperatures where the monomers were isotropic. High conversion was obtained below final T_g—even then, probably because the polymers were ordered. All the polymers were studied by WAXD and dynamic mechanical spectroscopy. Solid-state NMR on B3A showed that there was very high conversion of the double bonds at all temperatures. B3A photopolymerized in the smectic state (60–76°C) produced a crystalline polymer with T_g = 185°C (1 Hz). When photopolymerized at 85°C, above the isotropization temperature (T_i), a poorly organized polymer was obtained with a T_g of 155°C (1 Hz). Monomers with an odd number of methylene groups as spacers were crystalline after polymerization. With an even number of methylene groups, they lost most of their crystallinity on polymerization below T_i, but retained a low order smectic structure. Similar structures were obtained with all the monomers when they were polymerized above T_i. There was little effect of polymerization temperature on T_g when the spacers had an even number of methylene groups. © 1993 John Wiley & Sons, Inc.     

Synthesis and properties of reactive liquid crystal monomers and side-chain liquid crystalline polymers

Two nematic liquid crystal (LC) monomers containing double bonds in the side chain were designed and synthesised. Length of the side groups varied from 1 to 2 methylene units. The side-chain polymers were synthesised by hydrosilylation reaction. The molecular structures of the intermediates and the LC monomers were characterised by Fourier transform infrared, elemental analysis and nuclear magnetic resonance spectroscopy. The thermal phase behaviour of the monomers and polymers were investigated by differential scanning calorimetry and polar optical microscopy coupled with hot stage. The LC monomers showed only one nematic mesophase in the cooling process. And, the two polymers exhibit an enantiotroppic nematic mesophase either in the heating or in the cooling process.     

Preparation and electro‐optical properties of polymer dispersed liquid crystal films with relatively low liquid crystal content

In this paper, polymer dispersed liquid crystals (PDLC) films with LC content as low as 40 wt% were prepared, and the electro‐optical properties were carefully investigated. To accomplish this, different (meth)acrylate copolymerizaiton monomers have been used. The electro‐optical properties and morphologies of the PDLC films were strongly influenced by the chemical structure of copolymerization monomers (hydroxypropyl methacrylate (HPMA), glycidyl methacrylate, hydroxypropyl acrylate) and their feed ratio. Lower driven voltage and higher contrast ratio were achieved when the PDLC films showed a morphology with suitably LC domain size. At high HPMA content, a thin polymer film was formed on the surface of PDLC samples, which is beneficial to decrease the total LC content in PDLC devices. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of pressure on the B2I phase transition of a banana-shaped liquid crystal

Employing a phenomenological mean field theory, we analyse the effect of high pressure on the B₂I phase transition properties of a bent-core liquid crystal. The basic idea of the work is to explain the phase transition behaviour of system by assuming that certain Landau coefficients associated with the order parameters coupling terms of the free-energy density expansion are pressure dependent. We observe excellent agreement between the theoretical and experimental results of mesogen PHDBB and that the B₂I transition remains first order even at the elevated pressures.     

The effect of mono-sized liquid crystal domains on electro-optical properties in a polymer dispersed liquid crystal prepared by using monodisperse poly(methylmethacrylate)/liquid crystal microcapsules

Highly mono-sized poly(methyl methacrylate) (PMMA)/liquid crystal (LC) microcapsules having a mono-sized single LC domain were prepared by the solute codiffusion method and solvent evaporation. The size of the LC domain in the microcapsules could be controlled by the amount of LC introduced during the swelling stage. The electro-optical properties of the polymer dispersed liquid crystal (PDLC) prepared by using the microcapsules was highly improved. In particular, the threshold voltage was lowered and the switching behaviour with an applied electric field was sharpened drastically compared with PDLC prepared simply by solvent evaporation-induced phase separation.     

A greener electrochromic liquid crystal based on ionic liquid electrolytes

An electrochromic liquid crystal (ECLC) material composed of only liquid crystal (LC) and ionic liquid (IL) was developed. The LC containing the substituted diphenylacetylene serves as electrochromic (EC) material to realise transmittance and colour change under the direct current (DC) field, while the IL with the designable cation and anion served as electrolyte. Herein, a series of IL electrolytes was screened to investigate how IL tunes the electro-optic performance of the ECLC cell. By testing the electrochemistry window of ILs in EC cells, IL with the [NTf₂]^? anion shows adequate electrochemical stability when the EC material undergoes oxidation and reduction. The electro-optic performance of ECLC containing 1-ethoxy-4-[2-(4-pentylphenyl) ethynyl]-benzene (PEB) and IL was then evaluated by UV-vis spectrometry under the control of an electrochemical work station. Compared with other PEB-IL, PEB-[Bmim][NTf₂] with [Bmim][NTf₂] electrolyte shows a satisfactory transmittance at low operating voltage. Furthermore, Pd NPs in situ formed in [Bmim][NTf₂] reduced the EC potential and improved the light scattering of the ECLC cell. In this work, we also designed a bifunctional device based on polymer dispersed liquid crystal (PDLC) that hosts electrochromic guest molecules, and analysed the electro-optical and electrochromic properties of LC electrolyte mixtures, in order to gain control of the incident daylight and glare in building and automotive applications.     

Effects of the structures of epoxy monomers on the electro-optical properties of heat-cured polymer-dispersed liquid crystal films

Polymer-dispersed liquid crystal (PDLC) films were prepared from thermal polymerisation-induced phase separation in heat-curable monomers/nematic liquid crystal (LC) mixtures. For PDLCs with a certain amount of LCs, the microstructure and the refractive index of polymer networks could be influenced by the relative content of epoxy monomers, owing to their different chemical structures. The effect of these factors on the electro-optic properties of films was also investigated.     

Synthesis of thermotropic liquid crystal polyimide and its properties

Thermotropic liquid crystal polyimide which has neither an ester linkage nor a carbonate linkage was prepared by the polymerization of 1,2,4,5-benzenetetracarboxylic dianhydride (PMDA) and 1,3-bis[4-(4′-aminophenoxy)cumyl)]benzene (BACB). This polyimide shows the liquid crystal phase at 549-593 K. Mixing this liquid crystal polyimide or copolymerizing BACB decreases the melt viscosity of the thermoplastic polyimide (Aurum). © 1994 John Wiley & Sons, Inc.     

Crystallisation of nematic liquid crystal mixtures

In this paper, we propose a method to accelerate the crystallisation of nematic liquid crystal mixtures based on crystallisation theory. This method is to hold a nematic liquid crystal sample at a temperature suitable for crystal growth after aging it at a temperature suitable for nucleation. After we specified these temperatures of a nematic liquid crystal mixture using differential scanning calorimetry, we demonstrate that the two-temperature aging method is effective for the crystallisation of other nematic liquid crystal mixtures in which the crystal-liquid crystal transition temperature has so far been undetectable.     

点击化学合成盘-棒-盘状液晶三聚体

本文设计并合成了一系列盘-棒-盘状液晶三聚体.此类三聚体由两个相同的苯并菲盘状介晶基元和一个联苯棒状介晶基元通过CuI-NEt3体系催化端基炔和端基叠氮化合物的点击反应连接形成.该三聚体结构通过核磁、红外和高分辨质谱表征;介晶性通过偏光显微镜(POM)、差示扫描量热法(DSC)和X射线衍射(XRD)进行了研究.结果显示:此类液晶三聚体均为室温液晶,呈现四方柱状相(Colr).连接3个介晶基元的柔性间隔基的长度对化合物的相转变温度具有明显影响.     

Effects of crosslinking agent/diluents/thiol on morphology of the polymer matrix and electro-optical properties of polymer-dispersed liquid crystal

To study effects of the crosslinking agent/diluents/thiol on morphology of the polymer matrix and the electro-optical properties of polymer-dispersed liquid crystal (PDLC) films, samples were prepared by ultraviolet (UV)-initiated polymerisation. Due to the interaction between thiol–acrylate reaction and acrylate monomers polymerisation, the sample compositions were the foremost determinant to the microstructures which in turn played an essential role on the electro-optical properties of the PDLC films. With the increasing content of the crosslinking agent, the LC droplet size decreased, while the thiol had a contrary effect on the LC droplet size. It was demonstrated that the superior properties of the low-driven voltage (37.2 V), the high contrast ratio (148.2), the short response time (14.9 ms) and the high saturation transmittance (86.6%) could benefit from a novel microstructure which had a dense surface and meshes with microspheres attached. It was of great significance for the optimisation and the potential applications of the PDLC films.