Dielectric anisotropy in the nematic phase of 8PCH as a function of temperature and pressure

The dielectric permittivity components, ε_∥ and ε_⊥, in the nematic phase of 8PCH (trans-4-n-octyl(4-cyanophenyl)cyclohexane) were measured at 1 atm as a function of temperature (T), and at two temperatures as a function of pressure (p). A close similarity of the temperature and pressure behaviours of the dielectric anisotropy, δε = ε_∥ - ε_⊥, was established. It is argued that p and T are equivalent quantities in the formation of the nematic state. The well known Maier and Meier equations describe the dielectric parameters under both p = constant and T = constant conditions fairly well.     

Electrical conductivity and dielectric constant measurements of liquid crystal–gold nanoparticle composites

The behaviour of the anisotropic electrical conductivity of liquid crystal–gold nanoparticle (LC‐GNP) composites consisting of a commercially available room temperature nematic compound doped with alkylthiol‐capped GNPs has been investigated. The nematic–isotropic transition of the composite decreases nearly linearly with increasing X, the concentration of GNP (in weight %) at a rate of about 1°C /weight %. The inclusion of GNPs increases the electrical conductivity of the system with the value increasing by more than two orders of magnitude for X = 5%. However, the anisotropy in conductivity, defined as the ratio of the conductivity along (σ_∥) and orthogonal (σ_⊥) to the director shows a much smaller but definite decrease as X increases.     

Dielectric studies and critical behaviour in the vicinity of nematic–isotropic phase transition of a smectogenic binary mixture showing induced nematic phase

The phase diagram of a binary mixture composed of compounds, one having NCS terminal group (4DBT, showing smectic A₁ phase) and the other with CN terminal group (11OCB, showing smectic A_d phase), exhibiting induced nematic phase in a certain concentration range (0.100 < x_4DBT < 0.951) is reported here. Results of the static dielectric parameters measurement on this binary system within the entire mesomorphic range are presented. Evidence of strong pretransitional behaviour near the nematic–isotropic (N–I) phase transition, indicating the influence of tricritical behaviour, is observed. Precise determination of discontinuity (ΔT) and the critical exponent (α) of N–I phase transition have been carried out. Moreover, the order parameter critical exponent β is correctly predicted by the tricritical hypothesis through the dielectric anisotropy data for all the investigated mixtures.     

Conformational effects on mesophase stability: numerical comparison of carborane diester homologous series with their bicyclo[2.2.2]octane,cyclohexane and benzene analogues

Three series of diesters of 4‐alkoxyphenols containing 12‐vertex p‐carborane (1A[n], n = 1–22), 10‐vertex p‐carborane (1B[n], n = 1–12) or bicyclo[2.2.2]octane (1C[n], n = 1–12) as the central structural element were prepared and investigated by optical and calorimetric methods. All carborane diesters exhibited exclusively nematic behaviour, whereas the carbocyclic analogues 1C[n] and also cyclohexane (1D[n]) and benzene (1E[n]) derivatives, showed early onset of SmA phase and complete disappearance of nematic behaviour. The isotropic transition temperatures, T _MI, for the five series of mesogens were analysed numerically using a three‐parameter exponential function. The resulting limiting values, T _MI(∞), provided a quantitative assessment of the central element ability to support the mesogenic state. They demonstrated that, whereas the T _MI(∞) values for the carbocycles, C, D, and E, are around 125°C, for carboranes A and B this value is 70±2°C and 49±19°C, respectively. Two types of comparative analysis of trends in T _MI relative to those of the terephthalate series 1E[n] demonstrated abnormal behaviour of both carborane series (1A[n] and 1B[n]) and also the cyclohexane series (1D[n]). The former showed progressive destabilisation of the mesophase, whereas the series 1D[n] exhibited increasing mesophase stability relative to 1E[n] with increasing chain length. Both of these effects were explained using conformational analysis of theoretical models and experimental molecular structures for 1A[3], 1B[4] and 1C[4]. The increasing relative destabilisation of the mesophase in the carborane derivatives was rationalised by the high order rotational axes in A and B and D _4d symmetry for B. The trend of the ΔT _MI values for series 1D[n] was explained with the existence of the equatorial‐axial conformational equilibrium for the cyclohexane derivatives. The clearing temperatures for the hypothetical pure diequatorial conformers 1D[n]‐ee were estimated.     

Synthesis and liquid crystalline properties of substituted 2,5‐diaryl 1,3,4‐oxadiazole derivatives without flexible chains

A series of new compounds based on aromatically 2,5‐disubstituted 1,3,4‐oxadiazoles without flexible chains, formulated as p‐R–C₆H₄–(OC₂N₂)–(p‐C₆H₄)₂–R′ with (i) R = CH₃O, R′ = CH₃O, CH₃S, F, H (Ia–Id), (ii) R = CH₃S, R′ = CH₃O, CH₃S, F, H (IIa–IId) and (iii) R = F, R′ = CH₃O, CH₃S, F, H (IIIa–IIId) (p‐C₆H₄ and OC₂N₂ represent a p‐phenylene spacer and a 1,3,4‐oxadiazole ring, respectively), were synthesised and characterised by ¹H and ¹³C NMR, MS and HRMS techniques. Mesomorphic properties were investigated using differential scanning calorimetry and polarizing optical microscopy. All of the target compounds (except Id, IId, IIIc and IIId) exhibited an enantiotropic nematic mesophase with high melting temperatures. The liquid crystalline properties of these compounds were influenced greatly by polarity, steric factors and positions of the terminal groups. The effect of the terminal groups on the liquid crystal properties is discussed.     

Chain orientation and anisotropies in optical and dielectric properties in thin films of stiff polyimides

Thin films of poly(p-phenylene biphenyltetracarboximide) (BPDA-PDA), prepared by thermal imidization of the precursor poly(amic acid) on substrates, have been investigated by optical waveguide, ultraviolet-visible (UV-VIS), infrared (IR), and dielectric spectroscopies. The polyimide films exhibit an extraordinarily large anisotropy in the refractive indices with the in-plane index n_∥ = 1.806 and the out-of-plane index n_⊥ = 1.589 at 1064 nm wavelength. No discernible effect of the film thickness on this optical anisotropy is found between films of ca. 2.1 and ca. 7.8 μm thickness. This large birefringence is attributed to the preferential orientation of the biphenyltetracarboximide moieties with their planes parallel to the film surface, coupled with the strong preference of BPDA-PDA chains to align along the film plane. The frequency dispersion of the in-plane refractive index n_∥ is consistent with the results calculated by the Lorentz–Lorenz equation from the UV-visible spectrum exhibiting several absorption bands in the 170–500 nm region. The contribution from the IR absorption in the range 7000–400 cm,^?1 computed by the Spitzer-Kleinmann dispersion relations from the measured spectra, adds ca. 0.046 to the in-plane refractive index n_∥. Tilt-angle–dependent polarized IR results indicate nearly the same increase for the out-of-plane index n_⊥. Application of the Maxwell relation then leads to the out-of-plane dielectric constant ε^⊥ ? 2.7 at 1.2 × 10¹³ Hz, as compared with the measured value of ca. 3.0 at 10⁶ Hz. Assuming this small difference to remain the same for the in-plane dielectric constants ε_∥, we obtain a very large anisotropy in the dielectric properties of these polyimide films with the estimated in-plane dielectric constant ε_∥ ? 3.4 at 1.2 × 10¹³ Hz, and ε_∥ ? 3.7 at 10⁶ Hz. © 1992 John Wiley & Sons, Inc.     

Molecular structure and the twist-bend nematic phase: the role of terminal chains

ABSTRACT

The synthesis and characterisation of two homologous series of non-symmetric dimers are reported, the 1-(4-methoxybiphenyl-4?-yl)-6-(4-alkylanilinebenzylidene-4?-oxy)hexanes (MeOB6O.m, m = 1–10) and 1-(4-methoxybiphenyl-4?-yl)-6-(4-alkyloxyanilinebenzylidene-4?-oxy)hexanes (MeOB6O.Om, m = 1–9). All 10 members of the MeOB6O.m series exhibit the conventional nematic phase. At lower temperatures, the members with m = 1–7 formed the twist-bend nematic phase, N_TB, whereas for m = 8–10 smectic behaviour replaced the N_TB phase. All nine members of the MeOB6O.Om series also show the conventional nematic phase and for m = 1–3, a strongly monotropic N_TB phase is also observed. The alkyloxy terminated dimers show the higher values of T_NI and T_{NTB N} . For both series, the values of T_NI and T_{NTB N} show a modest alternation and in the same sense as m is increased. These observations suggest that the spatial uniformity of molecular curvature is important in driving the formation of the N_TB phase. The observation of smectic behaviour is attributed to the molecular inhomogeneity arising from the long terminal alkyl chain driving microphase separation. The transitional behaviour of these series is compared to those of the corresponding cyanobiphenyl-based series and overarching observations discussed.     

Accurate measurement of the twist elastic constant of liquid crystal by using capacitance method

In this study, the twist elastic constant (k₂₂) of liquid crystals (LCs) was accurately measured using capacitance method. The constant can be obtained on the basis of accurate measurement of other LC parameters, such as parallel and vertical dielectric constants (ε_// and ε_⊥), splay and bend elastic constants (k₁₁ and k₃₃), and rotational viscosity coefficient (γ₁). First, by using dual-cell capacitance method and an LC cell capacitance model to measure ε_// and ε_⊥, k₁₁ and k₃₃ can be obtained from the threshold voltage determined from the voltage–capacitance curve of the parallel-aligned nematic LC layer and the comparison between the experimental and theoretical results based on the Frank elastic theory, respectively. In addition, γ₁ can be obtained from the measurement of the dynamic response in the parallel-aligned nematic cell. Finally, k₂₂ can be accurately determined using the threshold voltage of the twisted nematic LC cell. By adopting the above method, the measured k₂₂ for LC E7 was 6.7 × 10^?12 N. The proposed method is more rigorous and yields a more accurate measurement result than the other methods reported in the literature.     

Textural,thermal, optical and electrical properties of Iron nanoparticles dispersed 4′-(Hexyloxy)-4-biphenylcarbonitrile liquid crystal mixture

In this work, the effect of Iron nanoparticles (Fe NPs) dispersion in 4′-(Hexyloxy)-4-biphenylcarbonitrile (6OCB) nematic liquid crystal properties has been studied. Inclusion of Fe NPs (0.25 wt. %) in 6OCB liquid crystal (LC) on textures, isotropic–nematic transition temperature (T_I–N), electro-optical and dielectric properties have been investigated in planar aligned cell. The threshold voltage (V_th) and T_I–N decrease after dispersion of Fe NPs. Dielectric spectroscopy in nematic phase show that relaxation frequency (f_r) also decreases after dispersion of Fe NPs in 6OCB. The observed relaxation mode is due to the flip-flop motion of LC molecules about their short axis. The band gap and AC conductivity in case of 6OCB-Fe sample increase over pure 6OCB sample. A decrease in activation energy is also noticed.     

Equations of state for polyamide‐6 and its nanocomposites. 1. Fundamentals and the matrix

The pressure‐volume‐temperature (PVT) surface of polyamide‐6 (PA‐6) was determined in the range of temperature T = 300–600 K and pressure P = 0.1–190 MPa. The data were analyzed separately for the molten and the noncrystalline phase using the Simha‐Somcynsky (S‐S) equation of state (eos) based on the cell‐hole theory. At T_g(P) ≤ T ≤ T_m(P), the “solid” state comprises liquid phase with crystals dispersed in it. The PVT behavior of the latter phase was described using Midha‐Nanda‐Simha‐Jain (MNSJ) eos based on the cell theory. The data fitting to these two theories yielded two sets of the Lennard‐Jones interaction parameters: ε*(S‐S) = 34.0 ± 0.3 and ε*(MNSJ) = 22.8 ± 0.3 kJ/mol, whereas v*(S‐S) = 32.00 ± 0.1 and v*(MNSJ) = 27.9 ± 0.2 mL/mol. The raw PVT data were numerically differentiated to obtain the thermal expansion and compressibility coefficients, α and κ, respectively. At constant P, κ followed the same dependence on both sides of the melting zone near T_m. By contrast, α = α(T) dependencies were dramatically different for the solid and molten phase; at T < T_m, α linearly increased with increasing T, then within the melting zone, its value step‐wise decreased, to slowly increase at higher temperatures. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 299–313, 2009     

Experimental Study of the Reactions of OH Radicals with Propane,n‐Pentane,and n‐Heptane over a Wide Temperature Range

The kinetics of the reactions of propane, n‐pentane, and n‐heptane with OH radicals has been studied using a low‐pressure flow tube reactor (P = 1 Torr) coupled with a quadrupole mass spectrometer. The rate constants of the title reactions were determined under pseudo–first‐order conditions, monitoring the kinetics of OH radical consumption in excess of the alkanes. A newly developed high‐temperature flow reactor was validated by the study of the OH + propane reaction, where the reaction rate constant, k₁ = 5.1 × 10^?17T^1.85exp(–160/T) cm³ molecule^?1 s^?1 (uncertainty of 20%), measured in a wide temperature range, 230–898 K, was found to be in excellent agreement with previous studies and current recommendations. The experimental data for the rate constants of the reactions of OH with n‐pentane and n‐heptane can be represented as three parameter expressions (in cm³ molecule^?1 s^?1, uncertainty of 20%): k₂ = 5.8 × 10^?18T^2.2exp(260/T) at T= 248–900 K and k₃ = 2.7 × 10^?16T^1.7exp(138/T) at T= 248–896 K, respectively. A combination of the present data with those from previous studies leads to the following expressions: k₁ = 2.64 × 10^?17T^1.93exp(–114/T), k₂ = 9.0 × 10^?17T^1.8 exp(120/T), and k₃ = 3.75 × 10^?16 T^1.65 exp(101/T) cm³ molecule^?1 s^?1, which can be recommended for k₁, k₂, and k₃ (with uncertainty of 20%) in the temperature ranges 190–1300, 240–1300, and 220–1300 K, respectively.     

Liquid density,viscosity and spectroscopic studies of binary mixture of tetraethylene glycol + 1,2-ethanediamine for CO2 capture

Thermophysical properties for binary mixture of tetraethylene glycol (T₄EG) (1) + 1,2-ethanediamine (EDA) (2), a potential scrubbing solution for the absorption of CO₂, are very important as well as lacking in the literatures. This work reports densities and viscosities over the entire concentration range for the binary mixture at T = (293.15-318.15) K under atmospheric pressure. According to the experimental density and viscosity values, the mixtures’ excess molar volume (V_m^E), absolute viscosity deviation (?η), excess free energies of activation (?G*^E), apparent molar volumes, partial molar volumes and isobaric thermal expansion coefficient were calculated, respectively. Meanwhile, the V_m^E, ?η and ?G*^E values were fitted by a Redlich–Kister equation to obtain coefficients. To further study, the Fourier transform infrared, UV-Vis and fluorescence spectra of T₄EG + EDA mixtures with various concentrations were measured, and the intermolecular interaction of T₄EG with EDA was also discussed as the formation of –OCH₂CH₂O–H···N(H₂)CH₂CH₂(H₂)N···.     

Ab initio study of the OH + CH2O reaction: The effect of the OH··OCH2 complex on the H‐abstraction kinetics

Kinetics for the reaction of OH radical with CH₂O has been studied by single‐point calculations at the CCSD(T)/6‐311+G(3df, 2p) level based on the geometries optimized at the B3LYP/6‐311+G(3df, 2p) and CCSD/6‐311++G(d,p) levels. The rate constant for the reaction has been computed in the temperature range 200–3000 K by variational transition state theory including the significant effect of the multiple reflections above the OH··OCH₂ complex. The predicted results can be represented by the expressions k₁ = 2.45 × 10^‐21 T^2.98 exp (1750/T) cm³ mol^?1 s^?1 (200–400 K) and 3.22 × 10^‐18 T^2.11 exp(849/T) cm³ mol^?1 s^?1 (400–3000 K) for the H‐abstraction process and k₂ = 1.05 × 10^‐17 T^1.63 exp(?2156/T) cm³ mol^?1 s^?1 in the temperature range of 200–3000 K for the HO‐addition process producing the OCH₂OH radical. The predicted total rate constants (k₁ + k₂) can reproduce closely the recommended kinetic data for OH + CH₂O over the entire range of temperature studied. © 2006 Wiley Periodicals, Inc. Int J Chem Kinet 38: 322–326, 2006     

Elastic,dielectric and optical constants of the nematic mixture E49

The Merck nematic mixture E49 exhibits a large nematic interval (0–100 °C) and a large dielectric anisotropy. Both of these features make E49 interesting for applications and basic physics. Unfortunately, no systematic measurements of the material constants of this mixture and their temperature dependence have been reported in the literature. In this paper we report experimental measurements of the splay and bend elastic constants (K ₁₁ and K ₃₃) of the ordinary and the extraordinary refractive indices (n _ort and n _par) at the wavelength λ?=?632.8 nm and of the two elastic constants parallel and orthogonal to the director (ε_par and ε_ort) at the frequency ν?=?5?kHz. The temperature dependence of all of these parameters is found in the temperature range 25–99 °C. The measurements of the elastic constants are performed using both a dielectric and an optical method simultaneously on the same nematic sample. The results obtained using the two methods are in a satisfactory agreement between them within the estimated experimental uncertainty. The ordinary and the extraordinary indices are measured using the prism method.     

Non‐monotonic temperature dependence of the alignment of a nematic mixture on a ferroelectric substrate

Polarization optic techniques have been applied to study specific features of the anisotropic interaction between a dye‐doped eutectic mixture of nematic liquid crystals p‐methoxybenzylidene‐p‐n‐butylaniline and p‐ethoxybenzylidene‐p‐n‐butylaniline and a polar surface of a ferroelectric triglycine sulphate crystal over the temperature range including the substrate Curie point T _c. It has been found that the temperature‐induced structural changes in the nematic layer in the vicinity of T _c are related to the changes in the orientational part of the tensor order parameter Q_ik . The temperature dependence of the director angle θ¯, averaged over the nematic layer, has been obtained from the effective dichroism values of solute absorption. The experimental data were interpreted using the model, in which the anisotropic part of the surface energy has two terms with orthogonal easy axes.     

Synthesis, crystal structures and magnetic properties of M(II)Cu(II) chains (M = Mn and Co) with sterically hindered alkyl-substituted phenyloxamate bridging ligands

A series of neutral oxamato‐bridged heterobimetallic chains of general formula [MCu(L^x)₂(S)₂] ? p S ? q H₂O [p=0–1, q=0–2.5; L¹=N‐2,6‐dimethylphenyloxamate, S=DMF with M=Mn ( 1 a ) and Co ( 1 b ); L²=N‐2,6‐diethylphenyloxamate, S=DMF with M=Mn ( 2 a ) and Co ( 2 b ) or S=DMSO with M=Mn ( 2 c ) and Co ( 2 d ); L³=N‐2,6‐diisopropylphenyloxamate, S=DMF with M=Mn ( 3 a ) and Co ( 3 b ) or S=DMSO with M=Mn ( 3 c ) and Co ( 3 d )] were prepared by treating the corresponding anionic oxamatocopper(II) complexes [Cu(L^x)₂]^2? (x=1–3) with M²⁺ cations (M=Mn and Co) in DMF or DMSO as the solvent. The single‐crystal X‐ray structures of 2 a and 3 a reveal the occurrence of well‐isolated, zigzag, oxamato‐bridged manganese(II)–copper(II) chains. The intrachain Cu ??? Mn distances across the oxamato bridge are 5.3761(7) and 5.4002(17) Å for 2 a and 3 a , respectively, whereas the shortest interchain Mn ??? Mn distances are 9.4475(16) and 8.1649(14) Å for 2 a and 3 a , respectively. All of these M^IICu^II chains (M=Mn and Co) exhibit 1D ferrimagnetic behaviour with moderately strong intrachain antiferromagnetic coupling between the square‐planar Cu^II and octahedral high‐spin M^II ions across the oxamato bridge [?J=31.4–35.2 and 33.4–44.8 cm^?1, respectively; H =∑_i?J S _M,i( S _Cu,i+ S _Cu,i?1)]. Only the Co^IICu^II chains show slow magnetic relaxation effects characteristic of single‐chain magnets (SCMs). Analysis of the magnetic relaxation dynamics of 3 d shows a thermally activated mechanism (Arrhenius law dependence) with values of the pre‐exponential factor (τ₀=2.6×10^?9 s) and activation energy (E_a=7.7 cm^?1) that are typical of SCMs. In contrast, two relaxation regimes are observed for 2 d in different temperature regions (τ₀=3.2×10^?10 s and E_a=24.7 cm^?1 for T<4.5 K and τ₀=3.2×10^?14 s and E_a=37.5 cm^?1 for T>4.5 K).     

Synthesis,Structures, and Properties of Crystalline Salts with Radical Anions of Metal‐Containing and Metal‐Free Phthalocyanines

Radical anion salts of metal‐containing and metal‐free phthalocyanines [MPc(3?)]^.?, where M=Cu^II, Ni^II, H₂, Sn^II, Pb^II, Ti^IVO, and V^IVO ( 1 – 10 ) with tetraalkylammonium cations have been obtained as single crystals by phthalocyanine reduction with sodium fluorenone ketyl. Their formation is accompanied by the Pc ligand reduction and affects the molecular structure of metal phthalocyanine radical anions as well as their optical and magnetic properties. Radical anions are characterized by the alternation of short and long C?N_imine bonds in the Pc ligand owing to the disruption of its aromaticity. Salts 1 – 10 show new bands at 833–1041 nm in the NIR range, whereas the Q‐ and Soret bands are blue‐shifted by 0.13–0.25 eV (38‐92 nm) and 0.04–0.07 eV (4–13 nm), respectively. Radical anions with Ni^II, Sn^II, Pb^II, and Ti^IVO have S=1/2 spin state, whereas [Cu^IIPc(3?)]^.? and [V^IVOPc(3?)]^.? containing paramagnetic Cu^II and V^IVO have two S=1/2 spins per radical anion. Central metal atoms strongly affect EPR spectra of phthalocyanine radical anions. Instead of narrow EPR signals characteristic of metal‐free phthalocyanine radical anions [H₂Pc(3?)]^.? (linewidth of 0.08–0.24 mT), broad EPR signals are manifested (linewidth of 2–70 mT) with g‐factors and linewidths that are strongly temperature‐dependent. Salt 11 containing the [Na^IPc(2?)]^? anions as well as previously studied [Fe^IPc(2?)]^? and [Co^IPc(2?)]^? anions that are formed without reduction of the Pc ligand do not show changes in molecular structure or optical and magnetic properties characteristic of [MPc(3?)]^.? in 1 – 10 .     

Thermotropic liquid crystals based on ferrocenylbiphenyl and ferrocenylterphenyl

4′‐Ferrocenyl‐1,1′‐biphenyl‐4‐yl 4‐alkoxybenzoates Fc–(C₆H₄)₂–OC(O)–C₆H₄–O–C _n H_2n+1 (n = 8, 10, 12) (3a–c), representing a new class of ferrocene‐containing thermotropic mesogens with nematogenic properties, were prepared. Two approaches were used for the construction of these mesogens: (i) reaction of 4′‐ferrocenyl‐1,1′‐biphenyl‐4‐ol with 4‐alkoxybenzoylchlorides, and (ii) crosscoupling of tris(4‐ferrocenylphenyl)boroxine with the corresponding halobenzenes. Crosscoupling was also applied for the synthesis of terphenyl‐containing mesogens Fc–(C₆H₄)₃–OC(O)–C₆H₄–O–C _n H_2n+1 (n = 10, 12) (6a,b) and (RC₅H₄)Fe‐[C₅H₄–(C₆H₄)₃–OC(O)–C₆H₄–O–C₁₀H₂₁] (11a, R = Et; 11b, R = n?Bu). The latter compounds also form nematic phases. Mesogens 6a,b form mesophases with wider temperature ranges than their biphenyl‐containing counterparts 3b,c. The most pronounced mesomorphism was displayed by compounds 11a and 11b, which have mesophases in the ranges 141–253°C and 120–238°C, respectively. The purity of compounds was established by ¹H NMR spectra and elemental analysis. Mesophases were identified by polarizing optical microscopy and differential scanning calorimetry.