Single-lobed Near Diffraction-limited Beam from 1W Laser Diode Array with an External Cavity

Abstract　An external cavity for the laser diode array with a conventional mirror in what we call two-time self-injection operation is presented. The external cavity consists of two lenses, a flat external mirror(EM) in the image plane of the array and a prism that is used as an output coupler. The single-lobed near diffraction-limited far field beam of a 1 W 10-stripe gain-guided LD array lies at 6.4°～9° with the external cavity operation in two-time self-injection mode, whereas at 2.5°～3.0° for its normal feedback operation. The width of the far field beam (FWHM) is 0.43° and 0.63° at driving current of 2 and 3.2 ×Ithr, respectively, much narrower than that in normal feedback operation, but at the expense of lower output power. The output of the system is very stable and insensitive to the tilt and position of the EM.     

808 nm激光二极管阵列波长光束组合20 W输出

 基于多波长光束组合技术,利用光栅的衍射和外腔的反馈,将激光二极管阵列(LDA)发光单元锁定在不同的波长上,以近似平行光束沿光栅的-1级衍射方向组合输出,改善LDA输出光束质量。实验采用发光单元宽度为100 μm、周期为500 μm,由19个单元构成的1 cm普通商用LDA,在连续运行最大注入电流60.6 A时,自由运转输出功率49.8 W时,获得功率为20.1 W的组合光束稳定输出,其光谱宽度为15 nm,对应的远场发散角由约70 mrad变为1.66 mrad,改善后光束质量因子约为32,其值与单个发光单元的光束质量相当。     

Beam Profile Improvement of a LD Array by an External Cavity with Photorefractive Phase Conjugate Mirror

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｓｅｍｉｃｏｎｄｕｃｔｏｒｌａｓｅｒ ｄｉｏｄｅａｒｒａｙｓａｒｅｖｅｒｙａｔｔｒａｃｔｉｖｅｆｏｒｔｈｅｉｒｃｏｍｐａｃｔｎｅｓｓ,ｓｉｍｐｌｅｏｐｅｒａｔｉｏｎ,ｌｏｎｇｌｉｆｅｔｉｍｅ,ａｎｄｈｉｇｈｅｌｅｃｔｒｉｃａｌｔｏｏｐｔｉｃａｌｃｏｎｖｅｒｓｉｏｎｅｆｆｉｃｉｅｎｃｙ.Ｈｏｗｅｖｅｒｔｈｅｓｅｈｉｇｈｐｏｗｅｒｓｏｕｒｃｅｓｈａｖｅａｎｏｎ ｄｉｆｆｒａｃｔｉｏｎ ｌｉｍｉｔｅｄｒａｄｉａｔｉｏｎｐａｔｔｅｒｎｗｉｔｈｖｅｒｙｌｏｗｃｏｈｅｒｅｎｃｅｌｅｎ…     

半导体激光器列阵在外腔下的光谱特性

使用普通高反镜作为19个单元的半导体激光器列阵(LDA)的外腔,通过调节高反镜的位置和角度,使LDA发出的光反馈回有源层,从而压窄了输出光谱并降低了LDA的阈值电流.实验中,运行于外腔下的LDA在不同的驱动电流下的输出光谱均被压窄到了原来的1/10左右,阈值电流从7 A降到了5.5 A,并且在9 A的偏置电流下输出功率提高了2倍.     

Coherent beam combination of broad-area laser diode array using off-axis external cavity with double feedback

In this letter, we demonstrate coherent beam combination of laser diode array using the external Talbot cavity with double feedback. The double feedback elements consist of grating and high-reflection plane mirror. Compared with single high-reflection plane mirror feedback, the external Talbot cavity with double feedback reduce the number of interference strips in the far-field pattern and narrow spectral line-width of the laser diode array. The results indicate that the application of the external Talbot cavity with double feedback produces a clear far-field interference pattern. In addition, line-width is reduced to 0.15 nm full-width at half-maximum (FWHM).     

采用多波长光束组合改善二极管激光阵列的光束质量

 基于多波长光束组合技术，利用光栅的衍射和外腔的反馈，将二极管阵列的发光单元锁定在不同的波长上，相邻单元的出射光波长有微小的差异。从外腔耦合镜输出近似平行的光束，其光束质量等同于单个发光单元的光束质量,而组合光束亮度随着组合光束个数定标放大。实验中采用发光单元宽度为100 μm、填充因子为0.5、由49个单元构成的1 cm 阵列获得功率为2.39 W的输出光束，其光谱宽度为27 nm，远场光斑的直径为0.08 mm，对应的远场发散角为1.2 mrad，其光束质量因子约为28，与单个发光单元的光束质量相当。     

利用外腔改善半导体激光器列阵的远场特性

采用一个由快轴准直透镜和一个高反射率平面镜组成的简单外腔,在腔长为几个cm时实现了半导体激光器列阵中部分单元的锁相运行;DLA远场出现了3个瓣,每瓣发散角为10 mrad左右,对比度为50%;通过控制部分单元的输出,可以抑制旁瓣的能量.     

Achieving single-lobed far-field patterns of broad area laser diode with external cavity feedback

We demonstrate a technique for single transverse mode operation of high-power broad area laser diode (BAL). In the experiment, the HR mirror is used as an external cavity mirror and the grating is used as a wavelength selective component. By tiling the HR mirror and the grating, the number of transverse modes oscillating in the cavity can be limited and the spectral bandwidth of the laser diode can be reduced. A single-lobed near diffraction-limited laser beam with the beam divergence (FWHM) of 0.43°, the spectral line-width of 0.7 nm and the output power of 350 mW are obtained. With the feedback, the power density of the output laser beam is increased 6 times in comparison with the free running.     

窄线宽、高光束质量的外腔双反馈激光二极管阵列(英文)

设计了一种离轴双反馈外腔能够有效地改善激光二极管阵列的线宽和光束质量。闪耀光栅和高反镜之间形成了一个共振腔。通过调整光栅和高反镜之间的倾角可以选定一个空间模在共振腔中放大。将一个半波片插入外腔中的光栅反馈支路,来控制反馈光的数量,激光从光栅反馈支路输出。运用这项技术,在工作电流16 A,可以把激光二极管阵列的输出线宽压缩到0.15 nm,光束束宽积减小到283 mm.mrad。由于光栅的锁定作用,中心波长几乎不随温度的变化而改变。在工作电流17A时,输出激光的功率为2.44 W,斜率效率为0.5 W/A。     

Talbot外腔压窄线阵大功率半导体激光器输出谱宽

线阵半导体激光器（LDA）内部发光元周期排列,基于Talbot效应,改进传统Littrow外腔窄线宽系统,在Littrow外腔中置入反射率为20%平平镜构成Talbot外腔以进一步窄化激光器输出谱宽,并将外腔窄线宽输出通过铷池进行吸收实验。实验结果表明:铷池对Tablot外腔输出吸收系数比Littrow外腔吸收系数相对提高42.9%,说明Talbot外腔能有效提高外腔输出谱宽的均匀性,提高半导体激光器泵浦效率。     

三种半导体阵列光谱组束结构的输出特性

基于光谱光束组合技术,利用光栅的衍射和外腔的反馈,并通过加入光束整形系统,将标准的半导体激光阵列的发光单元锁定在窄线宽的不同波长上,以近似平行光束沿组合方向输出,以实现半导体激光阵列输出光束质量的改善和线宽的压窄。实验中采用发光单元宽度100μm,周期500μm,由19个单元构成的标准阵列,分别对快、慢轴准直后光谱组束、光束整形后光谱组束和线宽压窄外腔组束进行了实验验证,实现了组合光束与单个发光单元近似的光束质量,同时得到了较窄的线宽输出,并对实验结果进行了分析。     

体布拉格光栅外腔实现激光二极管阵列同相模输出

 采用体布拉格光栅作为商用二极管激光阵列外腔,通过将每个单元发出的光反馈回相邻单元实现了外腔锁相。采用这种方法对发光单元宽度为100 μm、周期为200 μm,由49个单元构成的二极管阵列进行了外腔锁相实验,在远场获得了高光束质量、窄带宽的稳定输出。二极管激光阵列自由运转下功率为15 W,经外腔锁相后输出功率为3.67 W,对应光束远场发散角1.47 mrad, 光谱的峰值半宽由1.7 nm压窄到0.17 nm。     

Observation of multi-path interference in broad-area semiconductor lasers with optical feedback

Multi-path interference effects induced by optical feedback in broad-area semiconductor lasers is experimentally studied. An external mirror and an internal laser cavity form a closed composite optical feedback loop. For a very small tilt of the external mirror for the exit facet along the stripe width of the active layer, the light emitted from the laser undergoes multi-path reflections in the composite cavity, and we therefore observe multi-path interference effects of the laser oscillations for a small mirror tilt. The laser output power always shows the fundamental mode of the single feedback loop together with an oscillation of a certain higher multi-path loop. The laser oscillation and the beam profile are strongly dependent on the tilt. We observed up to a nine-fold multi-path interference in the experiment.     

切削用量对铝靶表面质量的影响

采用单点金刚石切削技术，完成了对ICF实验用铝靶的切削加工，重点研究了切削用量对加工表面质量的影响。实验结果表明:采用较小的进给速度，较大的主轴转速能够获得较低的表面粗糙度，切削深度对表面质量影响较小。通过Form Talysurf 表面轮廓仪测量，结果表明表面粗糙度小于50 nm。     

分布反馈光纤激光器阵列中外腔反馈特性研究

以半导体激光器中的复合腔模型和实测的分布反馈光纤激光器的外腔端面反射率为基础,对不同反射率条件下分布反馈光纤激光器的输出功率进行了仿真,同时搭建了二基元分布反馈光纤激光器阵列实验平台,对仿真结果进行了验证.仿真与实验结果表明:外腔反馈光重新注入分布反馈光纤激光器会增加激光器的输出功率,降低了阵列的输出功率平坦性.并且外腔端面反射率越大,这种平坦性降低的效果越明显.在构建分布反馈光纤激光器阵列时,应考虑外腔反馈对阵列输出功率平坦性造成的影响,尽量选择外腔端面反射率较小的激光器进行组阵.     

基于组合模理论设计的激光二极管阵列外腔

针对激光二极管阵列提出了"组合模"概念,计算了组合模的远场分布.每个组合模在远场的空间分布呈双瓣结构.基于激光二极管阵列组合模的远场分布特征,设计了离轴外腔反馈的激光二极管阵列.运用此装置所获得激光二极管阵列的远场分布有了明显变化.与自由运转的激光二极管阵列相比,离轴外腔反馈的激光二极管阵列远场宽度减少了4.3倍.在抽运电流为16 A时,测得输出激光的功率1.82 W,这相当于相同电流下自由运转激光器输出功率的79%.组合模理论不仅可以用来指导设计一维离轴外腔反馈激光二极管阵列,而且也可以用于设计二维离轴外腔反馈激光二极管阵列.二维离轴外腔反馈激光二极管阵列可以产生高功率,高光束质量输出的激光.     

Modeling of vertical external cavity semiconductor laser with MQW resonant structure

Numerical model is developed for modeling pulsed operation of a vertical external cavity semiconductor laser (VECSEL) with a resonant gain structure. Properties of optical modes for compound resonator formed by Bragg reflector, chip boundary and external spherical mirror were studied. For above threshold operation carrier density in each of quantum wells (QW) obeys non-linear diffusion equation with a source supplied by electron-hole pairs generated in barrier layers by pump radiation or fast electron beam. A new iteration procedure for round-trip operator evaluation was developed, which provides linear growth of computation time with the number of QWs. Results of numerical simulations are reported for a VECSEL comprising 25 QW in resonant configuration and the output spherical mirror with curvature radius 3 cm. Variation of distance to the external mirror is found to result in notable changes in power and optical quality of the output beam. The decisive role of gain and index non-linearity in these changes is identified. A range of values of distance to external mirror is found where iterative procedure does not converge. In another range, the resulting solution depends on the initial conditions for the iteration procedure.     

腔外位相共轭镜对氩离子激光器输出特性的影响

以掺铜的钾钠铌酸锶钡晶体作为猫式自泵浦位相共轭镜，研究了位相共轭光的反馈对氩了激光器的输出功率，阈值工作电流，纵模及横模特性的影响，并对其机理进行了分析和讨论。     

A simple method for automatic cavity alignment of a solid-state laser

Misalignment of a laser cavity would result in the displacement of beam location on the cavity mirrors. We present a simple method for automatic cavity alignment of a solid-state laser through detecting the location of the laser beam on the rear mirror, with which neither external alignment beams nor modifications to the cavity are required. The rear mirror of the laser cavity is replaced by a tip/tilt mirror to compensate for the misalignment. Experiments show that this method could effectively correct the misalignment of the laser cavity and restore the output power to almost the original value when the resonator is well aligned.     

基于空间滤波的光纤激光被动相位锁定技术研究

基于空间滤波的被动相位锁定,对掺Yb光纤激光阵列的相干组束进行了理论和实验研究.分析了基于空间滤波光反馈相位锁定的原理,研究了远场相干光斑Strehl比与激光波长及光谱带宽的关系.建立了二维四路掺Yb光纤放大器阵列的被动相位锁定实验系统,实现了稳定的相干耦合激光输出,远场光斑Strehl比为0.77.测得输出激光光谱中单个纵模的带宽约为9.1 GHz,与理论计算符合较好. 关键词： 光纤激光 相干合成 环形腔