Improved methodology for the microwave digestion of carbonate-rich environmental samples

Microwave-assisted digestion permits a rapid and total dissolution of sediments and various other sample types, allowing easier and more accurate multi-element determinations. In this study, we present an optimised microwave digestion method for the complete digestion of 200 mg of carbonate-rich sediments. The optimised method prevents the formation of precipitates and assures a complete dissolution of the material. The optimised method involves treatment with concentrated hydrochloric acid (HCl) prior to microwave digestion, which prevents the formation of an insoluble calcium fluoride precipitate associated with the use of hydrofluoric acid (HF). Three different certified reference samples along with a pure calcium carbonate standard and a carbonate-rich in-house marine sediment sample were considered. Sediments were found to only be partially digested if insufficient HF was present, while a noticeable fluoride-based precipitate was found if excess HF was present. Twenty elements were analysed using sector field inductively coupled plasma mass spectrometry (ICP-MS) (Al, Ag, Ba, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Na, Ni, Sr, Th, Ti, U, V and Zn). A total sample digestion with average elemental recoveries above 90% was obtained by reacting carbonate-rich samples with HCl on a hotplate at 150°C for 2 h (time for the total release of generated CO₂), prior to any microwave digestion step. This extra step prevented the accumulation of gas in the sealed vessels during digestion, which would otherwise influence the carbonate chemical equilibria and make insoluble calcium available for precipitation. After this initial treatment, the improved digestion method consisted of microwave attack employing a mix of concentrated HCl, nitric acid (HNO₃) and HF (4 mL/10 mL/2 mL), followed by evaporation on a hotplate. The limits of detection (LOD) obtained using the optimised microwave protocol and ICP-MS measurements were below 0.1 µg/kg for the trace elements and below 0.2 mg/kg for major elements.     

Determination of thirteen common elements in food samples by inductively coupled plasma atomic emission spectrometry: comparison of five digestion methods

Five sample digestion procedures were evaluated for the determination of Al, B, Ca, Cu, Fe, K, Mg, Mn, Na, P, S, Sr, and Zn in food samples by inductively coupled plasma atomic emission spectrometry. The 5 procedures include dry ashing at 500 degrees C, wet digestion with HNO3-HClO4, microwave digestion with HNO3, microwave digestion with HNO3-H2O2, and microwave digestion with HNO3-H2O2-HF. For microwave digestion with HNO3-H2O2-HF, silicon (IV) oxide was used to eliminate the excess HF, making it possible to determine total Al, B, and other common elements accurately and simultaneously. Seven National Institute of Standards and Technology standard reference materials (SRMs) were analyzed to compare the recovery of 13 elements with above digestion procedures. The results demonstrated that the microwave digestion procedure with HNO3-H2O2-HF yielded the best recoveries for all 13 elements in the selected SRMs. The determined concentrations of most elements were close for all 3 microwave digestion procedures with the exception of Al in oyster tissue, bovine liver, and spinach. Notably, the wet digestion with HNO3-HClO4 is the simplest and the most effective procedure for the selected elements except Al and B. Although there are several concerns with the dry ashing procedure, it might be a preferable procedure for those analyses where only nonvolatile elements are to be determined and the concentrations of the elements are low.     

Determination of <Superscript>226</Superscript>Ra in sediments by ICP-MS: A comparative study of three sample preparation approaches

Three protocols (Method I: ion chromatography (IC) and extraction chromatography (EC), Method II: precipitation followed by IC, and Method III: adsorption onto MnO₂ followed by IC-EC) were investigated to determine their applicability for the separation and pre-concentration of ²²⁶Ra in sediments. ²²⁶Ra recoveries, measured using the isotope dilution method with ²²⁸Ra as yield tracer, and the removal of spectral and non-spectral interferences were evaluated. The formation of polyatomic interferences at m/z = 226 from elements found in the matrix of sediments was also investigated to assess the level of separation required. Methods I and III were found to be the most effective with respect to recoveries and interference removal. The efficiency of a rapid microwave based protocol for the complete digestion of 1 g of sediment is also described. The method was tested and ²²⁶Ra concentrations in the millibecquerel range (fg) were determined in a standard reference material and sediment cores collected from Lake Baikal.     

Characteristics of a novel UV-TiO2-microwave integrated irradiation device in decomposition processes

The efficiency of oxidation in wet decomposition procedures for organic materials can be of great importance to the quality of the analytical data from various measurement techniques. A novel, microwave-assisted, high-temperature/high-pressure UV-TiO₂ digestion procedure was developed for the accelerated decomposition of various biological samples. The technique is based on a closed, pressurized, microwave digestion apparatus (MW). UV irradiation is generated by immersed electrodeless Cd discharge lamp operated by the focused microwave field in the single polymer vessel. To enhance oxidation efficiency, a photocatalyst TiO₂ was added to the microwave heated Teflon bomb. Measures of digestion completeness were provided by the appearance of carbon content and determination of trace and minor elements, enabling a comparison of different digestion procedures and sample types. Compared with other digestion systems, unusually low residual carbon contents were obtained. For the organic compounds and biological samples digested, the residual carbon content was 1-2%, corresponding to a decomposition efficiency of 98-99%. The potential of the MW-UV-TiO₂ system was illustrated by the decomposition of four certified reference materials (serum, urine, milk, arsenobetaine solution) and subsequent determination of trace and minor elements. Recoveries between 92% and 107% were found.     

Comparative study of different digestion procedures using supplementary analytical methods for multielement-screening of more than 50 elements in sediments of the river Elbe

The suitability of four different digestion procedures, i.e. i.) an aqua regia digestion according to DIN 38 414-S7, ii.) a pressure digestion using HNO₃/HF in PTFE-vessels, iii.) a HNO₃/HF + HCl-pressure digestion in PTFE-vessels and iv.) a HNO₃/HF + HCl-pressure digestion using microwave induction, has been evaluated with regard to the quantitative determination of about 50 elements in environmental samples. Three sediments of the river Elbe and two standard reference materials (MESS-1 and NIST 1645) have been employed. The analytical results from the dissolved samples, obtained using inductively coupled plasma mass- and optical emission spectrometry as well as total reflection X-ray fluorescence spectrometry, have been compared with those obtained by instrumental neutron activation analysis. Only digestion procedures using HNO₃/HF with a subsequent evaporation to dryness and dissolution in HCl have led to appropriate results for a wide range of elements (more than 50 elements in total). Because of its low contamination risk and its time saving, the microwave digestion is preferred. For this digestion procedure the accordance among the different instrumental methods used is high (better than 15% deviation) in general. A few elements (16) could be determined quantitatively only by a single method.     

Closed-vessel microwave digestion technique for lichens and leaves prior to determination of trace elements (Pb,Zn, Cu) and stable Pb isotope ratios

A reliable and robust procedure using closed-vessel microwave digestion of lichens and leaves for precise and accurate determination of trace elements (Pb, Zn and Cu) and stable Pb isotope ratios is presented. The method was developed using certified reference material CRM 482 Pseudovernia furfurea (Lichens), NIST 1515 (Apple Leaves) and NIST 1547 (Peach Leaves) and tested on lichens from a mining site in Russia. A mixture of 3?mL of HNO₃, 3?mL of H₂O₂, 2?mL of H₂O and 0.8?mL of HF ensured complete sample dissolution with 100?±?5% recovery for Pb, Zn and Cu at a maximum temperature of 210°C and pressure of 350?psi. The amount of HF and microwave pressure significantly influenced Pb, Zn and Cu recovery. Comparison between EMMA-XRF and ICP-AES showed a good correlation between Pb, Zn and Cu concentrations. Using the newly developed digestion method, Pb isotopes in lichens from the mining site were determined with an internal precision better than 0.02%.     

Determination of oxygen in certain gases : Improved winkler method

An improved method is described for the determination of micro-amounts of oxygen gas in argon, carbon dioxide, helium, hydrogen and nitrogen by the Winkler. procedure. The technique is such that a mean standard deviation of ± 0.33 ppm oxygen with a reproducibility of ± 0.67 is obtained for gases varying in oxygen content from 1 to 30 ppm. The results are reproducible on a day-to-day basis. The reagent blank is equivalent to about 2.5 ppm with a deviation of 0.2 ppm. The method can be used for oxygen gas determination from 1 to 1.50 ppm. The accuracy of the method is ± 0.1 ppm for the lower range of oxygen concentrations.The method may also be extended to higher oxygen-containing gases, except that the oxygen determination is made by titration and smaller gas samples are used.     

Optimized microwave preparation procedure for the elemental analysis of aquatic sediment

 This paper summarizes several key points in applying the microwave preparation technique to the elemental analysis of aquatic sediments and reports systematic experiments in searching for an optimal microwave preparation procedure for element analysis in sediment samples. The determination of the elements Cu, Pb and Cd in a standard reference aquatic sediment sample (CRM 280, COMEUR) was achieved by first digesting the samples in a microwave oven equipped with PFA advanced composite vessels, followed by AAS measurement. The influence of microwave power, digestion time, various dissolution reagents and the HF removing conditions was studied. It has been shown that for a 0.1 g sediment sample the optimal microwave preparation conditions are: 4–5ml HNO₃/HF/H₂O₂ as solvent, digesting time 30 min with 100% microwave power and evaporating the residual acid within 8 min in an open vessel at 80 °C. The element recovery rates with AAS measurement can reach up to 92.4–100.6%. Received: 23 July 1996/Revised: 23 September 1996/Accepted: 25 September 1996     

Determination of Elemental Sulfur in Bottom Sediments Using High-Performance Liquid Chromatography

A procedure for determining elemental sulfur in bottom sediments by microcolumn reversed-phase high-performance liquid chromatography was developed. The analytical range was 4–1200 g/g (in terms of the dry weight of a sediment). The procedure is based on the direct injection of acetone extracts of sediments into a chromatographic column. The detection limit was 5 ng/peak (signal-to-noise ratio of 3 : 1); the relative standard deviation was 5.6%. Errors introduced at particular stages of analysis and the total errors were evaluated for different sampling techniques. The results of determining elemental sulfur in the core samples of bottom sediments from Lake Baikal are presented.     

Determination of elements in paints and paint scrapings by inductively coupled plasma atomic emission spectrometry using microwave assisted digestion

Summary Inductively coupled plasma atomic emission spectrometry (ICPAES) is applied to the determination of elements in paints and paint scrapings to evaluate potential occupational and environmental exposure to metals in paints. A microwave assisted digestion procedure of these materials using nitric and hydrofluoric acid mixtures under controlled pressure has been developed. The accuracy and repeatability of the recommended procedure for lead are documented and evaluated by analysing NIST SRM 1579 Powdered Lead Based Paint. Neutron activation analysis was applied as a reference method for other elements. A variety of industrial and domestic paints of different chemical composition were analysed. The advantages and limitations of microwave digestion of paints are discussed.     

Studies on the use of XeF2 as digestion reagent

A digestion procedure was developed for the determination of selected elements (Al, Ba, Ca, Ce, Cd, Co, Cr, Cu, Fe, La, Mg, Ni, Sr, Pb, Zn) in sediments using XeF₂. The use of XeF₂ has some interesting features but this reagent should be handled only under dry gas which is a severe limitation of the methodology. In a first step the sediment sample (0.1 g) is dried (120 °C) and digested by XeF₂ (1.5 g) in the vapor phase (190 °C; 9 × 10⁶ Pa). Then the dry residue is dissolved in aqua regia and the solution digested at high pressure once again (aqua regia digestion). Subsequently the digested solution is diluted with sub-boiling distilled water and is ready for the analysis by ICP-MS. The sediment standard CRM 320 was analyzed to verify the procedure. A comparison of the results with those obtained by the normally used fluoric acid digestion showed that the recovery rates of each investigated element agreed within a confidence interval of 95%, except Cr. The recovery rate of Cr was lower for the XeF₂ digestion than for the fluoric acid digestion by more than 5%. Further studies were focussed on the possible digestion of SiC by XeF₂ as first step for the trace element determination. In the gaseous reaction products Si could be detected by ICP-MS which gives evidence to a decomposition of SiC. A digestion procedure for small Si samples (0.010 g) was developed. Detection limits (DL) determined for selected elements of analytical interest (Al, Ca, Cd, Cr, Co, Cu, Fe, Mg, Ni, Pb) were between 1 to 12 ng/g. For most of the elements this is an improvement in comparison to the HF vapor phase digestion. The verification of the method was carried out with GFAAS. Received: 17 February 1999 / Revised: 15 June 1999 / Accepted: 17 June 1999     

A Comparison of Sample Preparation Procedures for the Determination of Iron and Zinc in Bulgur Wheat by Graphite Furnace Atomic Absorption Spectrometry

ABSTRACT

A comparison was made of different digestion methods for the determination of iron and zinc in two types of bulgur wheat prior to their analysis in graphite furnace atomic absorption spectrometry. Samples were digested by means of acid treatment in room temperature, acid treatment at 60°C in a water bath and in a microwave oven and by dry ashing in open ah system. Except for microwave digestion, the samples proved to be unclear. The concentrations of the elements studied in the bulgur samples obtained by the four digestion methods are inconsistent in limits of standard deviations. It was found that aluminum sulfate (4μg/10μl sample) added to the samples acted as a modifier, improving the signal shape and increasing the stability of slurries obtained from digestion procedures.     

Microwave digestion of "residual fuel oil" (NIST SRM 1634b) for the determination of trace elements by inductively coupled plasma-mass spectrometry

A microwave procedure for the digestion of the NIST 1634b reference material "residual fuel oil" in closed pressurized vessels was developed in an attempt to facilitate routine analysis and obtain reproducible conditions or comparable results. The influence of sample size, reagent composition and volume, microwave power, and duration of heating on the digestion procedure was studied. Pressure and temperature inside the reaction vessels were monitored to determine the progression of the reaction and to develop optimal conditions. A nine-step heating program requiring 36.5 min with microwave power not exceeding 450 W in the pulsed mode was found suitable for the digestion of approximately 250 mg fuel oil with a mixture of nitric acid (5.0 mL) and hydrogen peroxide (2.0 mL). The reproducibility of microwave power was determined in terms of the relative standard deviations (n = 3) for temperature (2.7%) and pressure (4.9%) data. The vapor pressures obtained with 5.0 mL Milli-Q water (heated) in an 80-mL digestion vessel showed good agreement with literature data. The excess acid in the resulting digests was removed by evaporation and the concentrations of 24 elements (Ag, Al, As, Ba, Bi, Ca, Cd, Co, Cr, Cu, Fe, Hg, Mg, Mo, Ni, Pb, Sb, Sn, Sr, Ti, Tl, V, U, and Zn) were determined in the diluted digests by inductively coupled plasma mass spectrometry (ICP-MS). The experimental results were in good agreement with the certified and recommended concentrations for eight elements (Al, As, Co, Cr, Ni, Pb, V, Zn) in solutions obtained after one digestion step. An additional digestion step, consisting of intermediate cooling and venting stages, was required for the accurate determination of Fe. No agreement was reached for Ca and Ba even after two-step digestion. The proposed method of digestion provided precise results with relative standard deviations generally less than 5% for most of the elements determined.     

Application of Leaching Tests for the Assessment of Available Heavy Metals from Domestic and Industrial Sludges

Various sludge samples from different domestic and industrial wastewater treatment plants were analyzed by Flame Atomic Absorption Spectrometry to evaluate their total and available contents of heavy metals (Cu, Cr, Ni, Pb, Zn and Fe). The EDTA and acetic acid single extraction procedures were applied to these samples with the aim to study the leaching behaviour of the metals in the different sludges and also to predict their possible mobility when these wastes are disposed on the environment and landfills. In acidic medium, a higher extraction efficiency was observed for the major part of the elements studied in the industrial sludges, except for Ni and Zn, which were also considerably released from domestic sludges. In contrast, in the presence of the EDTA complexing ligand, a more elevated mobility of metals was found in the domestic sludges and little or no metals were released from the industrial sludges. Moreover, the results of the microwave total digestions were compared, for all metals, with those obtained using a more simplified pseudototal digestion procedure (based on the EPA Method 3051, named microwave assisted acid digestion of sediments, sludges, soils and oils) and a good agreement was found between them, except for Cr and Ni in some particular samples. The between-batch precision (expressed as RSD) of both compared digestion methods was very similar and values lower than 7.7% were obtained in both cases. A certified domestic sludge material (SRM 2781) was employed to validate the two digestion procedures and no significant differences were found between the certified and experimental values for all the elements studied.     

Determination of uranium and selected elements in Polish dictyonema shales and sandstones by ICP-MS

Inductively coupled plasma mass spectrometry was used for characterization of Polish dictyonema shales and sandstones as a potential source of uranium and other technologically important elements. Influence of sample digestion of these materials for the determinations: U, Th, Cu, Co, Mn, Zn, La, V, Yb, Mo, Ni, Sb and Fe has been tested. The method involved two-step microwave acid digestion, followed by direct determination by ICP-MS. The instrument used for all determinations was ELAN DRC II (Perkin Elmer) with crossflow nebulizer with Scott double-pass spray chamber and Ni cones. Certified Reference Materials were used as a quality control standard to validate the applied analytical procedure. The expanded measurement uncertainty U (k = 2) ranged from 5 to 15 %, in dependence on the element. The obtained results provided information on the contents of minor and trace elements in shales and sandstones depending on their origin. At this moment, these geological deposits can be treated as a potential source of raw elements.     

超级微波消解-电感耦合等离子体发射光谱（ICP-OES）法测定土壤中18种元素

为提高土壤多元素同时检测的效率,采用超级微波消解-电感耦合等离子体发射光谱法测定土壤中钾、钠、钙、镁、铜、铁、锰、锌、磷、硫、硼、砷、镉、铬、铅、钴、镓、锂等18种元素含量。比较了超级微波消解、常规微波消解和电热板消解的处理效果,采用超级微波消解法对样品进行前处理,并优化了消解条件。在最优条件下,各元素的检出限在0.05~20 mg/kg,加标回收率在86.2%~107.5%,RSD在0.1%~3.0%,方法准确度及精密度可以满足多元素同时测定的需求,且该方法具有简单、快速、成本低、用酸量少、重现性好等特点。     

Focused microwave-assisted digestion of vegetal materials for the determination of essential mineral nutrients

An open focused microwave-assisted digestion procedure has been developed to decompose and dissolve vegetal matrices for subsequent macro- and micronutrients analysis. The parameters of the microwave oven were evaluated using an experimental design. Sulfuric acid (5 mL) and hydrogen peroxide (3 mL) were found to be suitable for quantitative determination of Ca, Cu, Fe, K, Mg, Mn, N, P, and Zn in 0.100-0.500 g of vegetal sample. The precision was better than 6% for all elements at different concentrations. Results for reference and laboratory control materials are in agreement with certified and indicative values. In addition, the sample digest could be used for ICP-OES of all the elements mentioned. The proposed microwave-assisted digestion procedure offers the ability to determine the most important essential plant nutrients in one unique solution by means of analytical techniques usually found in most laboratories.     

Microwave digestion of “residual fuel oil” (NIST SRM 1634b) for the determination of trace elements by inductively coupled plasma-mass spectrometry

A microwave procedure for the digestion of the NIST 1634b reference material “residual fuel oil” in closed pressurized vessels was developed in an attempt to facilitate routine analysis and obtain reproducible conditions or comparable results. The influence of sample size, reagent composition and volume, microwave power, and duration of heating on the digestion procedure was studied. Pressure and temperature inside the reaction vessels were monitored to determine the progression of the reaction and to develop optimal conditions. A nine-step heating program requiring 36.5 min with microwave power not exceeding 450 W in the pulsed mode was found suitable for the digestion of ～ 250 mg fuel oil with a mixture of nitric acid (5.0 mL) and hydrogen peroxide (2.0 mL). The reproducibility of microwave power was determined in terms of the relative standard deviations (n = 3) for temperature (2.7%) and pressure (4.9%) data. The vapor pressures obtained with 5.0 mL Milli-Q water (heated) in an 80-mL digestion vessel showed good agreement with literature data. The excess acid in the resulting digests was removed by evaporation and the concentrations of 24 elements (Ag, Al, As, Ba, Bi, Ca, Cd, Co, Cr, Cu, Fe, Hg, Mg, Mo, Ni, Pb, Sb, Sn, Sr, Ti, Tl, V, U, and Zn) were determined in the diluted digests by inductively coupled plasma mass spectrometry (ICP-MS). The experimental results were in good agreement with the certified and recommended concentrations for eight elements (Al, As, Co, Cr, Ni, Pb, V, Zn) in solutions obtained after one digestion step. An additional digestion step, consisting of intermediate cooling and venting stages, was required for the accurate determination of Fe. No agreement was reached for Ca and Ba even after two-step digestion. The proposed method of digestion provided precise results with relative standard deviations generally less than 5% for most of the elements determined.     

Automated microwave digestion of certifiable color additives for determination of mercury by cold vapor atomic absorption spectrometry

A procedure using an automated microwave flow digestion technique was developed and validated for the digestion of samples of certifiable color additives before mercury determination by cold vapor atomic absorption spectrometry. Recovery studies were performed by spiking most of the color additives subject to batch certification by the U.S. Food and Drug Administration with inorganic mercury (HgNO3) and with organic mercury (CH3HgCl). Successful recoveries of 72-113% Hg added at the 1 microg/g level were obtained. A method detection limit of 0.2 microg Hg/g was estimated from a Hg-spiked FD&C Yellow No. 6 sample. At the specification level of 1 ppm Hg (1 microg Hg/g), the 95% confidence interval was +/- 0.2 ppm (0.2 microg Hg/g).     

Extraction Preconcentration of Uranium and Thorium Traces in the Analysis of Bottom Sediments by Inductively Coupled Plasma Mass Spectrometry

A procedure was developed for determining trace amounts of uranium and thorium isotopes in bottom sediments from Lake Baikal. This procedure involves sample decomposition, the coextraction of uranium and thorium with trioctylphosphine oxide, the quantitative back extraction after diluting the extract with caprylic acid, and the ICP MS analysis of the back extract. The procedure was verified by analyzing a BIL-1 Lake Baikal bottom silt standard reference material using the developed procedure and independent methods. The detection limits of abundant uranium and thorium isotopes are restricted by blank measures and equal to 1 × 10^–7 mass %. The detection limits for²³⁴U and ²³⁰Th are 4 × 10^–10 and 6 × 10^–10 mass %, respectively.