Synthesis of nanocrystalline ZnO nanobelts via pyrolytic decomposition of zinc acetate nanobelts and their gas sensing behavior

The pyrolytic decomposition of layered basic zinc acetate (LBZA) nanobelts (NBs) into nanocrystalline ZnO NBs is investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). We also report on the gas sensing response of the resulting ZnO nanomaterial to CO. The LBZA NBs are grown at 65 °C in an aqueous solution of zinc acetate dihydrate. AFM and SEM results show as-grown products possess the characteristic layered structure of the LBZA crystals. XRD and XPS results show that annealing as-grown products at 210 °C in air causes a transformation from zinc acetate to nanocrystalline ZnO NBs via thermal decomposition. The ZnO crystalline domain size increases with temperature from 9.2 nm at 200 °C to 94 nm at 1000 °C, as measured from XRD. SEM shows evidence of sintering at 600 °C. The thickness of the NBs, determined via AFM, ranges from 10 to 50 nm and remains approximately constant with annealing temperature. XPS confirmed the chemical transformation from zinc acetate to ZnO and showed a significant remaining zinc hydroxide component for the ZnO NBs consistent with published results. PL measurements at room temperature show a blue shift in peak emission as the nanobelts change from LBZA to ZnO at 200 °C. Above this transition temperature, the ZnO nanobelts possess strong band edge emission at 390 nm and little broad band emission in the visible region. The AFM and SEM images reveal that the crystallites within the nanobelts orientate in rows along the long axis during annealing. This structure provides a high surface area to volume ratio of aligned nanoparticles which is beneficial for gas sensing applications. Gas sensors fabricated from 400 °C annealed nanobelts showed a response of 1.62 when exposed to 200 ppm of CO in dry air at 400 °C, as defined by the ratio of resistance before and during exposure. This indicates that ZnO nanostructures obtained by thermal decomposition of LBZA NBs could provide a cost effective route to high sensitivity gas sensors.     

Numerical study of the hydrodynamic drag force in atomic force microscopy measurements undertaken in fluids

When atomic force microscopy (AFM) is employed for in vivo study of immersed biological samples, the fluid medium presents additional complexities, not least of which is the hydrodynamic drag force due to viscous friction of the cantilever with the liquid. This force should be considered when interpreting experimental results and any calculated material properties. In this paper, a numerical model is presented to study the influence of the drag force on experimental data obtained from AFM measurements using computational fluid dynamics (CFD) simulation. The model provides quantification of the drag force in AFM measurements of soft specimens in fluids.The numerical predictions were compared with experimental data obtained using AFM with a V-shaped cantilever fitted with a pyramidal tip. Tip velocities ranging from 1.05 to 105 μm/s were employed in water, polyethylene glycol and glycerol with the platform approaching from a distance of 6000 nm. The model was also compared with an existing analytical model. Good agreement was observed between numerical results, experiments and analytical predictions. Accurate predictions were obtained without the need for extrapolation of experimental data. In addition, the model can be employed over the range of tip geometries and velocities typically utilized in AFM measurements.     

Characterization of the channel walls roughness in photonic crystal fibers

We present electron microscope (FEI NanoSEM) and atomic force microscopy measurements of surface roughness in nanochannels in photonic crystal fibers (PCF). A method was invented to cleave the PCF along the axis without damaging the surface structure in the nanochannels allowing us to characterize the morphology of the nanochannels in the PCF. A multi-wall carbon nanotube mounted onto commercial AFM probes and super sharp silicon non-contact mode AFM probes were used to characterize the wall roughness in the nanochannels. The roughness is shown to have a Gaussian distribution, and has an amplitude smaller than 0.5 nm. The height–height correlation function is an exponential correlation function with an autocorrelation length of 13 nm, and 27 nm corresponding with scan sizes of 200×100 nm², and 1600×200 nm², respectively.     

Temperature coefficient of resistance and thermal conductivity of Vanadium oxide ‘Big Mac’ sandwich structure

In this paper, we synthesize and characterize a thin film thermometer structure for infrared microbolometers. The structure is composed of alternating multilayers of Vanadium pentoxide (V₂O₅), 25 nm, and Vanadium (V), 5 nm, thin films deposited by rf magnetron and dc magnetron sputtering respectively and annealed for 20, 30 and 40 min at 300 °C in Nitrogen (N₂) atmosphere. The best achieved temperature coefficient of resistance (TCR) was found to be −2.57%/K for 40 min annealed samples. Moreover, we apply, for the first time, the photo-thermal deflection (PTD) technique for measuring the thermal conductivity of the synthesized thin films. The thermal conductivity of the developed thin films reveals an increase in thermal conductivity from 2 W/m K to 5.8 W/m K for as grown and 40 min annealed samples respectively.     

Using Zn as target to fabricate ZnO coating by thermal oxidation in air on quartz substrate

In this work, ZnO coatings were fabricated by the RF-sputtering method on quartz substrates in an inert gas ambient of Ar followed by a thermal oxidation process in air at different temperatures. The effect of thermal oxidation temperatures on the structures and photoluminescence (PL) properties of the coatings were studied. The structural characteristics of the samples were analyzed by X-ray diffraction (XRD) and atomic force microscope (AFM). The PL spectra were obtained by using a Xe laser as a light source with an excitation wavelength of 325 nm at room temperature. The force-curves were obtained by AFM. The results show that all the prepared ZnO coatings have a compact hexagonal wurtzite structure. With the increasing annealing temperature from 400 °C to 600 °C, the particle size, surface RMS roughness, photoluminescence intensity and adhesion force of the prepared ZnO coatings were increased as well.     

Mechano-chemical AFM nanolithography of metallic thin films: A statistical analysis

A mechano-chemical atomic force microscope (AFM) nanolithography on a metallic thin film (50 nm in thickness) covered by a spin-coated soft polymeric mask layer (50–60 nm in thickness) has been introduced. The surface stochastic properties of initial grooves mechanically patterned on the mask layer (grooves before chemical wet-etching) and the lithographed patterns on the metallic thin film (the grooves after chemical wet-etching) have been investigated and compared by using the structure factor, power spectral density, and AFM tip deconvolution analyses. The effective shape of cross section of the before and after etching grooves have been determined by using the tip deconvolution surface analysis. The wet-etching process improved the shape of the grooves and also smoothed the surface within them. We have indicated that relaxation of the surface tension of the deposited mask layer after the AFM scribing is independent from surface density of the grooves and also their length scale. Based on the statistical analysis, it was found that increase of the width of the grooves after the wet-etching and also relaxation of surface tension of the mask layer resulted in a down limit in the size of the metallic nanowires made by the combined nanolithography method. An extrapolation of the analyzed statistical data has indicated that, in this method, the minimum obtainable width and length of the metallic nanowires are about 55 nm and 2 μm, respectively.     

Ablation depth control with 40 nm resolution on ITO thin films using a square,flat top beam shaped femtosecond NIR laser

We reported on the ablation depth control with a resolution of 40 nm on indium tin oxide (ITO) thin film using a square beam shaped femtosecond (190 fs) laser (λ_p=1030 nm). A slit is used to make the square, flat top beam shaped from the Gaussian spatial profile of the femtosecond laser. An ablation depth of 40 nm was obtained using the single pulse irradiation at a peak intensity of 2.8 TW/cm². The morphologies of the ablated area were characterized using an optical microscope, atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDS). Ablations with square and rectangular types with various sizes were demonstrated on ITO thin film using slits with varying x–y axes. The stereo structure of the ablation with the depth resolution of approximately 40 nm was also fabricated successfully using the irradiation of single pulses with different shaped sizes of femtosecond laser.     

Design and experiment of spectrometer based on scanning micro-grating integrating with angle sensor

A compact, low cost, high speed, non-destructive testing NIR (near infrared) spectrometer optical system based on MOEMS grating device is developed. The MOEMS grating works as the prismatic element and wavelength scanning element in our optical system. The MOEMS grating enables the design of compact grating spectrometers capable of acquiring full spectra using a single detector element. This MOEMS grating is driven by electromagnetic force and integrated with angle sensor which used to monitored deflection angle while the grating working. Comparing with the traditional spectral system, there is a new structure with a single detector and worked at high frequency. With the characteristics of MOEMS grating, the structure of the spectrometer system is proposed. After calculating the parameters of the optical path, ZEMAX optical software is used to simulate the system. According the ZEMAX output file of the 3D model, the prototype is designed by SolidWorks rapidly, fabricated. Designed for a wavelength range between 800 nm and 1500 nm, the spectrometer optical system features a spectral resolution of 16 nm with the volume of 97 mm × 81.7 mm × 81 mm. For the purpose of reduce modulated effect of sinusoidal rotation, spectral intensity of the different wavelength should be compensated by software method in the further. The system satisfies the demand of NIR micro-spectrometer with a single detector.     

Submicron gold structures formed by atomic force microscopy lithography on thin films of poly(methyl methacrylate)

Thin films of poly(methyl methacrylate) (PMMA) (25 nm) deposited on gold coated glass substrates have been locally modified by exposure to biased atomic force microscopy (AFM) tips. Constant exposure currents in the range of 0.5–0.65 nA leads to removal of PMMA both by direct ablation and enhanced solubility in a developer solution. Possible mechanisms causing such modifications have been discussed. Submicron Au structures were formed by combining AFM lithography, involving localized removal of PMMA, with sputter deposition of gold and a lift-off process.     

Study on the interactions between anti-cancer drug oxaliplatin and DNA by atomic force microscopy

Oxaliplatin is one of the most important anticancer drugs at present. However, the mechanism of action of oxaliplatin is still controversial. In this study, the interactions between oxaliplatin and a plasmid DNA have been studied so as to reveal the structural basis of its activity. The structural characteristic of pUC19 DNA (2 ng/μL) incubated with 100 μmol/L and 1000 μmol/L of oxaliplatin for the different time on a freshly cleaved highly ordered pyrolytic graphite (HOPG) surface was investigated by atomic force microscopy (AFM). High resolution AFM observation indicated that oxaliplatin can induce pUC19 DNA molecules change from the extended conformation to the entangled structures with many nodes, and finally to the compact particles. The present AFM results provide structural evidence about the interactions between oxaliplatin and circular duplex DNA containing multiple targets.     

Physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing

This paper presents the physical properties of vacuum evaporated CdTe thin films with post-deposition thermal annealing. The thin films of thickness 500 nm were grown on glass and indium tin oxide (ITO) coated glass substrates employing thermal vacuum evaporation technique followed by post-deposition thermal annealing at temperature 450 °C. These films were subjected to the X-ray diffraction (XRD),UV-Vis spectrophotometer, source meter and atomic force microscopy (AFM) for structural, optical, electrical and surface morphological analysis respectively. The X-ray diffraction patterns reveal that the films have zinc-blende structure of single cubic phase with preferred orientation (111) and polycrystalline in nature. The crystallographic and optical parameters are calculated and discussed in brief. The optical band gap is found to be 1.62 eV and 1.52 eV for as-grown and annealed films respectively. The I–V characteristics show that the conductivity is decreased for annealed thin films. The AFM studies reveal that the surface roughness is observed to be increased for thermally annealed films.     

A comparison of the surface nanostructure from two different types of gram-negative cells: Escherichia coli and Rhodobacter sphaeroides

Bacteria have been studied using different microscopy methods for many years. Recently, the developments of high-speed atomic force microscopy have opened the doors to study bacteria in new ways due to the fact that it uses much less force on the sample while imaging. This makes the high-speed atomic force microscope an indispensable technique for imaging the surface of living bacterial cells because it allows for the high-resolution visualization of surface proteins in their natural condition without disrupting the cell or the activity of the proteins. Previous work examining living cells of Magnetospirillum magneticum AMB-1 demonstrated that the surface of these bacteria was covered with a net-like structure that is mainly composed of porin molecules. However, it was unclear whether or not this feature was unique to other living bacteria. In this study we used the high-speed atomic force microscope to examine the surface of living cells of Escherichia coli and Rhodobacter sphaeroides to compare their structure with that of M. magneticum. Our research clearly demonstrated that both of these types of cells have an outer surface that is covered in a network of nanometer-sized holes similar to M. magneticum. The diameter of the holes was 8.0 ± 1.5 nm for E. coli and 6.6 ± 1.1 nm for R. sphaeroides. The results in this paper confirm that this type of outer surface structure exists in other types of bacteria and it is not unique to Magnetospirillum.     

Influence of growth parameters on the properties of InGaN/GaN multiple quantum well grown by metalorganic chemical vapor deposition

The effects of growth parameters such as barrier growth time, growth pressure and indium flow rate on the properties of InGaN/GaN multiple quantum wells (MQWs) were investigated by using photoluminescence (PL), high resolution X-ray diffraction (HRXRD), and atomic force microscope (AFM). The InGaN/GaN MQW structures were grown on c-plane sapphire substrate by using metalorganic chemical vapor deposition. With increasing barrier growth time, the PL peak energy is blue-shifted by 18 nm. For InGaN/GaN MQW structures grown at different growth pressures, the PL intensity is maximized in the 300 Torr – grown structure, which could be attributed to the improved structural quality confirmed by HRXRD and AFM results. Also, the optical properties of InGaN/GaN MQW are strongly affected by the indium flow rate.     

Nonlinear optical properties of CdxZn1 − xO films deposited with PLD technique

In this paper, the structural and optical properties of Cd_xZn_1 ? xO films were studied. The films were deposited with pulse laser deposition (PLD) technique. The Cd concentration changed in the range from x = 0 to 0.2. The structure of the films was characterized by atom force microscope (AFM) and X-ray diffraction (XRD). The nonlinear optical properties were investigated by Z-scan methods. The two-photon absorption (TPA) coefficient β_eff was measured. The β_eff value changes from 49.2 cm/GW to 116.5 cm/GW with the Cd concentration from 0 to 15%.     

Synthesis of Ag-deionized water nanofluids using multi-beam laser ablation in liquids

Multi-pulse laser ablation of silver in deionized water was studied. The laser beams were arranged in a cross-beam configuration. In our experiments, two single-mode, Q-switched Nd-Yag lasers operating at 1064 nm, pulse duration of 5.5 ns and 10 Hz rep rate were used. The laser fluence of the second beam was 0.265 J/cm² for all tests. Two levels of the laser fluences were used for the ablating beam: 0.09 and 0.265 J/cm² (11,014 and 33,042 J/cm² at the focal point, respectively). The silver target was at 50 mm from the cell window and 10 mm deep. The second beam was aligned parallelly with the silver target and focused at 2 mm in front of the focal point of the ablating beam. For all cases, the delay time between the ablating beam and the cross-beam was 40 μs. In general, the ablated particles were almost all spherical. For fluence of 0.09 J/cm ² and single-beam approach, the mean particle size was about 29 nm. The majority of the particles, however, were in 19–35 nm range and there were some big ones as large as 50–60 nm in size. For double-beam approach, the particles were smaller with the average size of about 18 nm and the majority of the particles were in 9–21 nm range with few big one as large as 40 nm. For the beam fluence of 0.265 J/cm² and single-beam configuration, the particle sizes were smaller, the mean particles size was about 18 nm and the majority of the particles were in the range of 10–22 nm with some big one as large as 40 nm. For double-beam approach, the mean particle size was larger (24.2 nm) and the majority of the particle were distributed from 14 to 35 nm with some big particles can be found with sizes as big as 70 nm. Preliminary measurements of the thermal conductivity and viscosity of the produced samples showed that the thermal conductivity increased about 3–5% and the viscosity increased 3.7% above the base fluid viscosity even with the particle volume concentration as low as 0.01%.     

Surface topographic study of chalcogenide thin films of GexSb(As)40−xS50Te10 glasses

The surface topography and fractal properties of Ge_xSb(As)_40−xS₅₀Te₁₀ (x = 10, 20, 27 at.%) films, evaporated onto glass substrates, have been studied by atomic force microscopic imaging at different scales. The surface of the chalcogenide films is smooth (<5 nm roughness), isotropic and having some particular differences in texture. All films are self-similar with Mean Fractal Dimension in the range of 2.25–2.63. The films with Ge_xSb_40−xS₅₀Te₁₀ composition are more uniform in terms of surface morphology (grains structure) than those with Ge_xAs_40−xS₅₀Te₁₀ composition for which the film surface exhibits a superimposed structure of large particles at x = 10 and 20 at.%.     

Morphology of synthetic DOPA-eumelanin deposited on glass and mica substrates: An atomic force microscopy investigation

Bright field microscopy and atomic force microscopy techniques are used to investigate morphological properties of synthetic eumelanin, obtained by oxidation of l-DOPA solution, deposited on glass and mica substrates. Deposits of eumelanin are characterized by aggregates with different shape and size. On a micrometric scale, filamentous as well as granular structures are present on glass and mica substrates, with a larger density on the former than on the latter. On a nanometric scale, filamentous aggregates, several microns long and about 100 nm wide and high, and granular aggregates, ∼50 nm high and 100 nm wide, are found on both substrates, whereas point-like deposits less than 10 nm high and less than 50 nm wide are found on mica substrate. Dynamic light scattering measurements and atomic force microscopy images support the evidence that eumelanin presents only nanometric point-like aggregates in aqueous solution, whereas such nanoaggregates organize themselves according to granular and filamentous structures when deposition occurs, as a consequence of interactions with the substrate surface.     

Simultaneous measurement of refractive index and temperature using thinned fiber based Mach–Zehnder interferometer

A novel method for simultaneous measurement of refractive index and temperature based on a small core and cladding diameters thinned fiber Mach–Zehnder interferometer (MZI) using singlemode-multimode-thinned-multimode-singlemode (SMTMS) fiber structure is proposed. Experiments indicate that the selected two interference orders have sensitivities of ?16.1936 nm/RIU and 0.0534 nm/°C, and ?23.0473 nm/RIU and 0.0575 nm/°C, respectively, among RI range from 1.3325–1.3720 and temperature range from 22 °C–82 °C. We can thus use the coefficient matrix of these two peaks to simultaneously determine the surrounding refractive index and temperature. The fabrication is easy, safe and cost effective, includes only the fusion splicing, making the device properly attractive for practical sensor applications.     

Growth and electrical characterization of type II InAs/GaSb superlattices for midwave infrared detection

Herein, we report a type II InAs/GaSb superlattice structure (SLS) grown on GaSb(1 0 0) substrates by molecular beam epitaxy (MBE) and its electrical characterization for mid-wavelength infrared detection. A GaSb buffer layer was grown under optimized SLS growth conditions, which can decrease the occurrence of defects for similar pyramidal structures. The complications associated with these conditions include oxide desorption of the substrate, growth temperature of the SLS, the V/III ratio during superlattice growth and the shutter sequence. High-resolution X-ray diffraction (HRXRD) shows the sixth satellite peak, and the period of the SLS was 52.9 Å. The atomic force microscopy (AFM) images indicated that the roughness was less than 2.8 nm. High-resolution transmission electron microscopy (HRTEM) images indicated that the SLS contains few structural defects related to interface dislocations or strain relaxation during the growth of the superlattice layer. The photoresponse spectra indicated that the cutoff wavelength was 4.8 μm at 300 K. The SLS photodiode surface was passivated by a zinc sulfide (ZnS) coating after anodic sulfide.     

Gain flattening technique for optical wireless front-end receiver considering various large window photodetectors

A novel gain flattening technique for an optical wireless front-end receiver structure involving a bootstrap transimpedance amplifier (BTA) integrated with a MEMS variable feedback capacitor has been demonstrated. The MEMS varicap replaces a fixed capacitance as the feedback element in the front end system to optimize the performance of the BTA in terms of its frequency response. The implementation of the MEMS device with a BTA optical front-end receiver was verified using CoventorWare ARCHITECT. The simulation results showed that the approach can significantly flatten the peaking gain by up to 14 dB, when considering a system with various photodetector capacitances, ranging in value from 100 pF to 1 nF.