Determination of Polycyclic Aromatic Hydrocarbons and Their Methylated Derivatives in Sewage Sludge from Northeastern China: Occurrence,Profiles and Toxicity Evaluation

This paper assesses the occurrence, distribution, source, and toxicity of polycyclic aromatic hydrocarbons (PAHs), and their methylated form (Me-PAHs) in sewage sludge from 10 WWTPs in Northeastern China was noted. The concentrations of ∑PAHs, ∑Me-PAHs ranged from 567 to 5040 and 48.1 to 479ng.g−1dw, which is greater than the safety limit for sludge in agriculture in China. High and low molecular weight 4 and 2-ring PAHs and Me-PAHs in sludge were prevalent. The flux of sludge PAHs and Me-PAHs released from ten WWTPs, in Heilongjiang province, was calculated to be over 100 kg/year. Principal component analysis (PCA), diagnostic ratios and positive matrix factorization (PMF) determined a similar mixed pyrogenic and petrogenic source of sewage sludge. The average values of Benzo[a]pyrene was below the safe value of 600ng.g−1 dependent on an incremental lifetime cancer risk ILCR of 10⁻⁶. Sludge is an important source for the transfer of pollutants into the environment, such as PAHs and Me-PAHs. Consequently, greater consideration should be given to its widespread occurrence.     

Analytical Performance of Clay Paste Electrode and Graphene Paste Electrode-Comparative Study

The analytical performance of the clay paste electrode and graphene paste electrode was compared using square wave voltammetry (SWV) and cyclic voltammetry (CV). The comparison was made on the basis of a paracetamol (PA) determination on both working electrodes. The influence of pH and SWV parameters was investigated. The linear concentration ranges were found to be 6.0 × 10⁻⁷–3.0 × 10⁻⁵ and 2.0 × 10⁻⁶–8.0 × 10⁻⁵ mol L⁻¹ for clay paste electrode (ClPE) and graphene paste electrode (GrPE), respectively. The detection and quantification limits were calculated as 1.4 × 10⁻⁷ and 4.7 ×10⁻⁷ mol L⁻¹ for ClPE and 3.7 × 10⁻⁷ and 1.2 × 10⁻⁶ mol L⁻¹ for GrPE, respectively. Developed methods were successfully applied to pharmaceutical formulations analyses. Scanning electron microscopy and energy-dispersive X-ray spectroscopy were used to characterize ClPE and GrPE surfaces. Clay composition was examined with wavelength dispersive X-ray (WDXRF).     

Solubility and Thermodynamic Data of Febuxostat in Various Mono Solvents at Different Temperatures

This study examines the solubility and thermodynamics of febuxostat (FBX) in a variety of mono solvents, including “water, methanol (MeOH), ethanol (EtOH), isopropanol (IPA), 1-butanol (1-BuOH), 2-butanol (2-BuOH), ethylene glycol (EG), propylene glycol (PG), polyethylene glycol-400 (PEG-400), ethyl acetate (EA), Transcutol-HP (THP), and dimethyl sulfoxide (DMSO)” at 298.2–318.2 K and 101.1 kPa. The solubility of FBX was determined using a shake flask method and correlated with “van’t Hoff, Buchowski-Ksiazczak λh, and Apelblat models”. The overall error values for van’t Hoff, Buchowski-Ksiazczak λh, and Apelblat models was recorded to be 1.60, 2.86, and 1.14%, respectively. The maximum mole fraction solubility of FBX was 3.06 × 10⁻² in PEG-400 at 318.2 K, however the least one was 1.97 × 10⁻⁷ in water at 298.2 K. The FBX solubility increased with temperature and the order followed in different mono solvents was PEG-400 (3.06 × 10⁻²) > THP (1.70 × 10⁻²) > 2-BuOH (1.38 × 10⁻²) > 1-BuOH (1.37 × 10⁻²) > IPA (1.10 × 10⁻²) > EtOH (8.37 × 10⁻³) > EA (8.31 × 10⁻³) > DMSO (7.35 × 10⁻³) > MeOH (3.26 × 10⁻³) > PG (1.88 × 10⁻³) > EG (1.31 × 10⁻³) > water (1.14 × 10⁻⁶) at 318.2 K. Compared to the other combinations of FBX and mono solvents, FBX-PEG-400 had the strongest solute-solvent interactions. The apparent thermodynamic analysis revealed that FBX dissolution was “endothermic and entropy-driven” in all mono solvents investigated. Based on these findings, PEG-400 appears to be the optimal co-solvent for FBX solubility.     

Thermodynamic Solubility Profile of Temozolomide in Different Commonly Used Pharmaceutical Solvents

The solubility parameters, and solution thermodynamics of temozolomide (TMZ) in 10 frequently used solvents were examined at five different temperatures. The maximum mole fraction solubility of TMZ was ascertained in dimethyl sulfoxide (1.35 × 10⁻²), followed by that in polyethylene glycol-400 (3.32 × 10⁻³) > Transcutol^® (2.89 × 10⁻³) > ethylene glycol (1.64 × 10⁻³) > propylene glycol (1.47 × 10⁻³) > H₂O (7.70 × 10⁻⁴) > ethyl acetate (5.44 × 10⁻⁴) > ethanol (1.80 × 10⁻⁴) > isopropyl alcohol (1.32 × 10⁻⁴) > 1-butanol (1.07 × 10⁻⁴) at 323.2 K. An analogous pattern was also observed for the other investigated temperatures. The quantitated TMZ solubility values were regressed using Apelblat and Van’t Hoff models and showed overall deviances of 0.96% and 1.33%, respectively. Apparent thermodynamic analysis indicated endothermic, spontaneous, and entropy-driven dissolution of TMZ in all solvents. TMZ solubility data may help to formulate dosage forms, recrystallize, purify, and extract/separate TMZ.     

Fast Atom Bombardment Combined with Mass Spectrometry or Characterization of Polycyclic Aromatic Hydrocarbons

A new approach using fast atom bombardment combined with mass spectrometry to characterize polycyclic aromatic hydrocarbons (PAHs) in the range of 128–252 u molecular weight is described. Sulfolane was employed as a liquid matrix for these π-conjugated hydrocarbons. Bombardment of sulfolane solution of certain PAHs with an atom beam produces both radical cation (M⁺) and protonated molecule [(M + H)⁺], with no evidence of fragmentation. Collisional activation of the fast atom bombardment-desorbed M⁺ ions, however, results in several structure-specific fragment ions. Structural differences in a few isomeric hydrocarbons can be detected using the [(M + H)⁺]/[M⁺] abundance ratio and in the pyrene-fluoranthene pair by the B/E linked-field-collision-activated dissociation data. The [(M + H)⁺]/[M⁺] was found to be compound-specific and correlated well with certain properties (resonance energy, proton affinity, and ionizing energy) of PAHs.     

Agaricus bisporus Crude Extract: Characterization and Analytical Application

In the present work crude Agaricus bisporus extract (ABE) has been prepared and characterized by its tyrosinase activity, protein composition and substrate specificity. The presence of mushroom tyrosinase (PPO3) in ABE has been confirmed using two-dimensional electrophoresis, followed by MALDI TOF/TOF MS-based analysis. GH27 alpha-glucosidases, GH47 alpha-mannosidases, GH20 hexosaminidases, and alkaline phosphatases have been also detected in ABE. ABE substrate specificity has been studied using 19 phenolic compounds: polyphenols (catechol, gallic, caffeic, chlorogenic, and ferulic acids, quercetin, rutin, dihydroquercetin, l-dihydroxyphenylalanine, resorcinol, propyl gallate) and monophenols (l-tyrosine, phenol, p-nitrophenol, o-nitrophenol, guaiacol, o-cresol, m-cresol, p-cresol). The comparison of ABE substrate specificity and affinity to the corresponding parameters of purified A. bisporus tyrosinase has revealed no major differences. The conditions for spectrophotometric determination have been chosen and the analytical procedures for determination of 1.4 × 10⁻⁴–1.0 × 10⁻³ M l-tyrosine, 3.1 × 10⁻⁶–1.0 × 10⁻⁴ M phenol, 5.4 × 10⁻⁵–1.0 × 10⁻³ M catechol, 8.5 × 10⁻⁵–1.0 × 10⁻³ M caffeic acid, 1.5 × 10⁻⁴–7.5 × 10⁻⁴ M chlorogenic acid, 6.8 × 10⁻⁵–1.0 × 10⁻³ M l-DOPA have been proposed. The procedures have been applied for the determination of l-tyrosine in food supplements, l-DOPA in synthetic serum, and phenol in waste water from the food manufacturing plant. Thus, we have demonstrated the possibility of using ABE as a substitute for tyrosinase in such analytical applications, as food supplements, medical and environmental analysis.     

Determination of N-Acetyl-l-cysteine Ethyl Ester (NACET) by Flow Injection Analysis and Spectrophotometric Detection Using Different Thiol-Sensitive Ligands

A new flow injection spectrophotometric method for the determination of N-acetyl-l-cysteine ethyl ester (NACET) was developed and validated. The method is based on the reduction of Cu(II)-ligand complexes to chromophoric Cu(I)-ligand complexes with the analyte. The studied ligands were neocuproine (NCN), bicinchoninic acid (BCA) and bathocuproine disulfonic acid (BCS). The absorbance of the Cu(I)-ligand complex was measured at 458, 562 and 483 nm for the reactions of NACET with NCN, BCA and BCS, respectively. The method was validated in terms of linear dynamic range, limit of detection and quantitation, accuracy, selectivity, and precision. Experimental conditions were optimized by a univariate method, yielding linear calibration curves in a concentration range from 2.0 × 10⁻⁶ mol L⁻¹ to 2.0 × 10⁻⁴ mol L⁻¹ using NCN; 2.0 × 10⁻⁶ mol L⁻¹ to 1.0 × 10⁻⁴ mol L⁻¹ using BCA and 6.0 × 10⁻⁷ mol L⁻¹ to 1.2 × 10⁻⁴ mol L⁻¹ using BCS. The achieved analytical frequency was 90 h⁻¹ for all three ligands. The method was successfully employed for NACET determination in pharmaceutical preparations, indicating that this FIA method fulfilled all the essential demands for the determination of NACET in quality control laboratories, as it combined low instrument and reagent costs with a high sampling rate.     

Spectrophotometric Determination of Molybdenum(VI) as a Ternary Complex with 4-Nitrocatechol and Benzalkonium Chloride

A new liquid—liquid extraction system for molybdenum(VI) was studied. It contains 4-nitrocatechol (4NC) as a complexing chromogenic reagent and benzalkonium chloride (BZC) as a source of heavy cations (BZ⁺), which are prone to form chloroform-extractable ion-association complexes. The optimum conditions for the determination of trace molybdenum(VI) were found: concentrations of 4NC and BZC (7.5 × 10⁻⁴ mol dm⁻³ and 1.9 × 10⁻⁴ mol dm⁻³, respectively), acidity (3.75 × 10⁻² mol dm⁻³ H₂SO₄), extraction time (3 min), and wavelength (439 nm). The molar absorptivity, limit of detection, and linear working range were 5.5 × 10⁴ dm³ mol⁻¹ cm⁻¹, 5.6 ng cm⁻³, and 18.6–3100 μg cm⁻³, respectively. The effect of foreign ions was examined, and the developed procedure was applied to the analysis of synthetic mixtures and real samples (potable waters and steels). The composition of the extracted complex was 1:1:2 (Mo:4NC:BZ). Three possible structures of its anionic part [Mo^VI(4NC)O₂(OH)₂]²⁻ were discussed based on optimizations at the B3LYP/3-21G level of theory, and simulated UV/Vis absorption spectra were obtained with the TD Hamiltonian.     

New Strategies for the Simple and Sensitive Voltammetric Direct Quantification of Se(IV) in Environmental Waters Employing Bismuth Film Modified Glassy Carbon Electrode and Amberlite Resin

An analytical procedure regarding the determination of selenium(IV) by anodic stripping voltammetry exploiting the in situ plated bismuth film electrode is described. Since organics are commonly present in untreated natural water samples, the use of Amberlite XAD-7 resin turns out to be quite important to avoid problems such as the adsorption of these compounds on the working electrode. The optimum circumstances for the detection of selenium in water using differential pulse voltammetry techniques were found to be as follows: 0.1 mol L⁻¹ acetic acid, 1.9 × 10⁻⁵ mol L⁻¹ Bi(III), 0.1 g Amberlite XAD-7 resin, and successive potentials of −1.6 V for 5 s and −0.4 V for 60 s, during which the in situ formation of the bismuth film on glassy carbon and the accumulation of selenium took place. The current of the anodic peak varies linearly with the selenium concentration ranging from 3 × 10⁻⁹ mol L⁻¹ to 3 × 10⁻⁶ mol L⁻¹ (r = 0.9995), with a detection limit of 8 × 10⁻¹⁰ mol L⁻¹. The proposed procedure was used for Se(IV) determination in certified reference materials and natural water samples, and acceptable results and recoveries were obtained.     

Use of a Hydrophobic Azo Dye for the Centrifuge-Less Cloud Point Extraction–Spectrophotometric Determination of Cobalt

The hydrophobic azo dye 6-hexyl-4-(2-thiazolylazo)resorcinol (HTAR, H₂L) was studied as part of a system for the centrifuge-less cloud point extraction (CL-CPE) and spectrophotometric determination of traces of cobalt. The extracted 1:2 (Co:HTAR) complex, [Co^III(HL⁻)(L²⁻)]⁰, shows an absorption maximum at 553 nm and contains HTAR in two different acid–base forms. Optimum conditions for its formation and CL-CPE were found as follows: 1 × 10⁻⁵ mol L⁻¹ of HTAR, 1.64% of Triton X-114, pH of 7.8, incubation time of 20 min at ca. 50 °C, and cooling time of 30 min at ca. −20 °C. The linear range, limit of detection, and apparent molar absorptivity coefficient were 5.4–189 ng mL⁻¹, 1.64 ng mL⁻¹, and 2.63 × 10⁵ L mol⁻¹ cm⁻¹, respectively. The developed procedure does not use any organic solvents and can be described as simple, cheap, sensitive, convenient, and environmentally friendly. It was successfully applied to the analysis of artificial mixtures and real samples, such as steel, dental alloy, rainwater, ampoules of vitamin B₁₂, and saline solution for intravenous infusion.     

The Use of a Solid Bismuth Microelectrode for Vanadium Quantification by Adsorptive Stripping Voltammetry in Environmental Water Samples

This paper presents for the first time the use of an environmentally friendly solid bismuth microelectrode for the voltammetric quantification of V(V) in natural water samples. These studies were designed to replace the film bismuth electrode that had been introduced to eliminate the conventional sensors based on highly toxic mercury. In the proposed procedure, V(V) is preconcentrated at the solid bismuth microelectrode surface via the formation of electroactive complexes with cupferron from a solution of 0.1-mol L⁻¹ acetate buffer, pH = 4.6 at a potential of −0.4 V. The linearity of the calibration graph is in the V(V) concentration range from 8 × 10⁻¹⁰ to 1 × 10⁻⁷ mol L⁻¹ with a preconcentration time of 1 min. The limit of detection (calculated as 3 σ) is 2.5 × 10⁻¹⁰ mol L⁻¹ for a preconcentration time of 1 min. It was also demonstrated that significant improvement in analytical parameters was achieved as a result of the activation of the solid electrode surface at a potential of −2.5 V for 2 s. The developed procedure is highly selective for the presence of foreign ions and organic compounds in tested samples. The accuracy of the recommended procedure was checked using SPS-WW1 waste water-certified reference materials of a complex composition, in which the concentration of V(V) determined by the proposed method was 95.1 ± 1.6 ng mL⁻¹. Moreover, in keeping with the outlined procedure, river, tap and rain water samples were analyzed without any pretreatment, and recovery values from 96% to 106% were obtained.     

The Effect of Growth Parameters on Electrophysical and Memristive Properties of Vanadium Oxide Thin Films

We have experimentally studied the influence of pulsed laser deposition parameters on the morphological and electrophysical parameters of vanadium oxide films. It is shown that an increase in the number of laser pulses from 10,000 to 60,000 and an oxygen pressure from 3 × 10⁻⁴ Torr to 3 × 10⁻² Torr makes it possible to form vanadium oxide films with a thickness from 22.3 ± 4.4 nm to 131.7 ± 14.4 nm, a surface roughness from 7.8 ± 1.1 nm to 37.1 ± 11.2 nm, electron concentration from (0.32 ± 0.07) × 10¹⁷ cm⁻³ to (42.64 ± 4.46) × 10¹⁷ cm⁻³, electron mobility from 0.25 ± 0.03 cm²/(V·s) to 7.12 ± 1.32 cm²/(V·s), and resistivity from 6.32 ± 2.21 Ω·cm to 723.74 ± 89.21 Ω·cm. The regimes at which vanadium oxide films with a thickness of 22.3 ± 4.4 nm, a roughness of 7.8 ± 1.1 nm, and a resistivity of 6.32 ± 2.21 Ω·cm are obtained for their potential use in the fabrication of ReRAM neuromorphic systems. It is shown that a 22.3 ± 4.4 nm thick vanadium oxide film has the bipolar effect of resistive switching. The resistance in the high state was (89.42 ± 32.37) × 10⁶ Ω, the resistance in the low state was equal to (6.34 ± 2.34) × 10³ Ω, and the ratio R_HRS/R_LRS was about 14,104. The results can be used in the manufacture of a new generation of micro- and nanoelectronics elements to create ReRAM of neuromorphic systems based on vanadium oxide thin films.     

Solubility Optimization of Loxoprofen as a Nonsteroidal Anti-Inflammatory Drug: Statistical Modeling and Optimization

Industrial-based application of supercritical CO₂ (SCCO₂) has emerged as a promising technology in numerous scientific fields due to offering brilliant advantages, such as simplicity of application, eco-friendliness, and high performance. Loxoprofen sodium (chemical formula C₁₅H₁₈O₃) is known as an efficient nonsteroidal anti-inflammatory drug (NSAID), which has been long propounded as an effective alleviator for various painful disorders like musculoskeletal conditions. Although experimental research plays an important role in obtaining drug solubility in SCCO₂, the emergence of operational disadvantages such as high cost and long-time process duration has motivated the researchers to develop mathematical models based on artificial intelligence (AI) to predict this important parameter. Three distinct models have been used on the data in this work, all of which were based on decision trees: K-nearest neighbors (KNN), NU support vector machine (NU-SVR), and Gaussian process regression (GPR). The data set has two input characteristics, P (pressure) and T (temperature), and a single output, Y = solubility. After implementing and fine-tuning to the hyperparameters of these ensemble models, their performance has been evaluated using a variety of measures. The R-squared scores of all three models are greater than 0.9, however, the RMSE error rates are 1.879 × 10⁻⁴, 7.814 × 10⁻⁵, and 1.664 × 10⁻⁴ for the KNN, NU-SVR, and GPR models, respectively. MAE metrics of 1.116 × 10⁻⁴, 6.197 × 10⁻⁵, and 8.777 × 10⁻⁵errors were also discovered for the KNN, NU-SVR, and GPR models, respectively. A study was also carried out to determine the best quantity of solubility, which can be referred to as the (x₁ = 40.0, x₂ = 338.0, Y = 1.27 × 10⁻³) vector.     

A small-molecule organic ferroelectric with piezoelectric voltage coefficient larger than that of lead zirconate titanate and polyvinylidene difluoride

Piezoelectric materials that generate electricity when deforming are ideal for many implantable medical sensing devices. In modern piezoelectric materials, inorganic ceramics and polymers are two important branches, represented by lead zirconate titanate (PZT) and polyvinylidene difluoride (PVDF). However, PVDF is a nondegradable plastic with poor crystallinity and a large coercive field, and PZT suffers from high sintering temperature and toxic heavy element. Here, we successfully design a metal-free small-molecule ferroelectric, 3,3-difluorocyclobutanammonium hydrochloride ((3,3-DFCBA)Cl), which has high piezoelectric voltage coefficients g₃₃ (437.2 × 10⁻³ V m N⁻¹) and g₃₁ (586.2 × 10⁻³ V m N⁻¹), a large electrostriction coefficient Q₃₃ (about 4.29 m⁴ C⁻²) and low acoustic impedance z₀ (2.25 × 10⁶ kg s⁻¹ m⁻²), significantly outperforming PZT (g₃₃ = 34 × 10⁻³ V m N⁻¹ and z₀ = 2.54 × 10⁷ kg s⁻¹ m⁻²) and PVDF (g₃₃ = 286.7 × 10⁻³ V m N⁻¹, g₃₁ = 185.9 × 10⁻³ V m N⁻¹, Q₃₃ = 1.3 m⁴ C⁻², and z₀ = 3.69 × 10⁶ kg s⁻¹ m⁻²). Such a low acoustic impedance matches that of the body (1.38–1.99 × 10⁶ kg s⁻¹ m⁻²) reasonably well, making it attractive as next-generation biocompatible piezoelectric devices for health monitoring and “disposable” invasive medical ultrasound imaging.

A small-molecule organic ferroelectric (3,3-DFCBA)Cl has high piezoelectric voltage coefficients g₃₃ (437.2 × 10⁻³ V m N⁻¹), a large electrostriction coefficient Q₃₃, and low acoustic impedance z₀, far beyond that of PZT and PVDF.     

Optical and Photoacoustic Properties of Laser-Ablated Silver Nanoparticles in a Carbon Dots Solution

This study used the carbon dots solution for the laser ablation technique to fabricate silver nanoparticles. The ablation time range was from 5 min to 20 min. Analytical methods, including Fourier transform infrared spectroscopy (FTIR), UV-visible spectroscopy, transmission electron microscopy, and Raman spectroscopy were used to categorize the prepared samples. The UV-visible and z-scan techniques provided optical parameters such as linear and nonlinear refractive indices in the range of 1.56759 to 1.81288 and 7.3769 × 10⁻¹⁰ cm² W⁻¹ to 9.5269 × 10⁻¹⁰ cm² W⁻¹ and the nonlinear susceptibility was measured in the range of 5.46 × 10⁻⁸ to 6.97 × 10⁻⁸ esu. The thermal effusivity of prepared samples, which were measured using the photoacoustic technique, were in the range of 0.0941 W s^1/2 cm⁻² K⁻¹ to 0.8491 W s^1/2 cm⁻² K⁻¹. The interaction of the prepared sample with fluoride was investigated using a Raman spectrometer. Consequently, the intensity of the Raman signal decreased with the increasing concentration of fluoride, and the detection limit is about 0.1 ppm.     

Inclusion Complex between Local Anesthetic/2-hydroxypropyl-β-cyclodextrin in Stealth Liposome

The drugs delivery system in the treatment of diseases has advantages such as reduced toxicity, increased availability of the drug, etc. Therefore, studies of the supramolecular interactions between local anesthetics (LAs) butamben (BTB) or ropivacaine (RVC) complexed with 2-hydroxypropyl-β-cyclodextrin (HP-βCD) and carried in Stealth liposomal (SL) are performed. ¹H-NMR nuclear magnetic resonance (DOSY and STD) were used as the main tools. The displacements observed in the ¹H-NMR presented the complexion between LAs and HP-βCD. The diffusion coefficients of free BTB and RVC were 7.70 × 10⁻¹⁰ m² s⁻¹ and 4.07 × 10⁻¹⁰ m² s⁻¹, and in the complex with HP-βCD were 1.90 × 10⁻¹⁰ m² s⁻¹ and 3.64 × 10⁻¹⁰ m² s⁻¹, respectively, which indicate a strong interaction between the BTB molecule and HP-βCD (98.3% molar fraction and Ka = 72.279 L/mol). With STD-NMR, the encapsulation of the BTB/HP-βCD and RVC/HP-βCD in SL vesicles was proven. Beyond the saturation transfer to the LAs, there is the magnetization transfer to the hydrogens of HP-βCD. BTB and RVC have already been studied in normal liposome systems; however, little is known of their behavior in SL.     

Characterizing the Diffusion and Rheological Properties of Aged Asphalt Binder Rejuvenated with Bio-Oil Based on Molecular Dynamic Simulations and Laboratory Experimentations

Soybean-derived bio-oil is one of the vegetable-based oils that is gaining the most interest for potential use in the rejuvenation of aged asphalt binders. This laboratory study was conducted to characterize and quantify the diffusion and rheological properties of bio-oil-rejuvenated aged asphalt binder (BRAA) using soybean oil. In the study, the chemical structure of the soybean oil was comparatively characterized using an element analyzer (EA), gel permeation chromatography (GPC), and a Fourier infrared (FTIR) spectrometer, respectively. Based on the chemical structure of the bio-oil, BRAA molecular models were built for computing the diffusion parameters using molecular dynamic simulations. Likewise, a dynamic shear rheometer (DSR) test device was used for measuring and quantifying the rheological properties of the aged asphalt binder rejuvenated with 0%, 1%, 2%, 3%, 4%, and 5% soybean oil, respectively. The laboratory test results indicate that bio-oil could potentially improve the diffusion coefficients and phase angle of the aged asphalt binder. Similarly, the corresponding decrease in the complex shear modulus has a positive effect on the low-temperature properties of BRAA. For a bio-oil dosage 4.0%, the diffusion coefficients of the BRAA components are 1.52 × 10⁻⁸, 1.33 × 10⁻⁸, 3.47 × 10⁻⁸, 4.82 × 10⁻⁸ and 3.92 × 10⁻⁸, respectively. Similarly, the corresponding reduction in the complex shear modulus from 1.27 × 10⁷ Pa to 4.0 × 10⁵ Pa suggests an improvement in the low-temperature properties of BRAA. Overall, the study contributes to the literature on the potential use of soybean-derived bio-oil as a rejuvenator of aged asphalt binders.     

Absolute Antioxidant Activity of Five Phenol-Rich Essential Oils

Essential oils (EOs) have promising antioxidant activities which are gaining interest as natural alternatives to synthetic antioxidants in the food and cosmetic industries. However, quantitative data on chain-breaking activity and on the kinetics of peroxyl radical trapping are missing. Five phenol-rich EOs were analyzed by GC-MS and studied by oxygen-uptake kinetics in inhibited controlled autoxidations of reference substrates (cumene and squalene). Terpene-rich Thymus vulgaris (thymol 4%; carvacrol 33.9%), Origanum vulgare, (thymol 0.4%; carvacrol 66.2%) and Satureja hortensis, (thymol 1.7%; carvacrol 46.6%), had apparent k_inh (30 °C, PhCl) of (1.5 ± 0.3) × 10⁴, (1.3 ± 0.1) × 10⁴ and (1.1 ± 0.3) × 10⁴ M⁻¹s⁻¹, respectively, while phenylpropanoid-rich Eugenia caryophyllus (eugenol 80.8%) and Cinnamomum zeylanicum, (eugenol 81.4%) showed apparent k_inh (30 °C, PhCl) of (5.0 ± 0.1) × 10³ and (4.9 ± 0.3) × 10³ M⁻¹s⁻¹, respectively. All EOs already granted good antioxidant protection of cumene at a concentration of 1 ppm (1 mg/L), the duration being proportional to their phenolic content, which dictated their antioxidant behavior. They also afforded excellent protection of squalene after adjusting their concentration (100 mg/L) to account for the much higher oxidizability of this substrate. All investigated EOs had k_inh comparable to synthetic butylated hydroxytoluene (BHT) were are eligible to replace it in the protection of food or cosmetic products.     

Simultaneous Determination of Polycyclic Aromatic Hydrocarbons by Variable Angle Spectrofluorimetry

Abstract

The use of variable-angle fluorescence spectra together with multilinear curve-fitting techniques for the resolution of mixtures of polycyclic aromatic hydrocarbons (PAHs), is described. Only one spectrum is necessary to determine four compounds in a mixture even when a severe overlap occurs. The PAHs are quantified at ng/ml levels.     

Host-Guest Complexation of Oxaliplatin and Para-Sulfonatocalix[n]Arenes for Potential Use in Cancer Therapy

P-sulfonatocalix[n]arenes have demonstrated a great potential for encapsulation of therapeutic drugs via host-guest complexation to improve solubility, stability, and bioavailability of encapsulated drugs. In this work, guest-host complexes of a third-generation anticancer drug (oxaliplatin) and p-4-sulfocalix[n]arenes (n = 4 and 6; p-SC4 and p-SC6, respectively) were prepared and investigated, using ¹H NMR, UV, Job’s plot analysis, and DFT calculations, for use as cancer therapeutics. The peak amplitude of the prepared host-guest complexes was linearly proportional to the concentration of oxaliplatin in the range of 1.0 × 10⁻⁵ M⁻¹ to 2.1 × 10⁻⁴ M⁻¹. The reaction stoichiometry between either p-SC4 or p-SC6 and oxaliplatin in the formed complexes was 1:1. The stability constants for the complexes were 5.07 × 10⁴ M⁻¹ and 6.3 × 10⁴ M⁻¹. These correspond to complexation free energy of −6.39 and −6.52 kcal/mol for p-SC4 and p-SC6, respectively. Complexation between oxaliplatin and p-SC4 or p-SC6 was found to involve hydrogen bonds. Both complexes exhibited enhanced biological and high cytotoxic activities against HT-29 colorectal cells and MCF-7 breast adenocarcinoma compared to free oxaliplatin, which warrants further investigation for cancer therapy.