铁电晶体Pb_xBa_(1-x)Nb_2O_6和掺Li,Na的Pb_xBa_(1-x)Nb_2O_6的结构和电弹张量的测定

用提拉法从熔体中生长出Pb_(0.37)Ba_(0.63)Nb_2O_6和Pb_(0.30)Ba_(0.533)Na_(0.306)Li_(0.028)Nb_2O_6 两种铁电单晶。用X射线衍射方法分析了两种单晶的结构,结果表明,室温时两种晶体都属于四方晶系点群4mm。测定晶格参数得PBN晶体的a=12.493A和c=3.98A;掺Li,Na的PBN晶体的a=12.493A和c=3.970A。测定了两种晶体全部各52个电弹张量的分量,结果表明PBN晶体具有优良的压电性,其中压电系数d_15=108×10~(-12)C/N。这种晶体很有希望用作与厚度切变模式有关的压电换能器材料。掺Li,Na的PBN晶体的介电常数显著降低,而铁电居里点有明显的提高。     

铁电晶体(K0.20Na0.20Sr0.60Ba0.20)Nb2O6全部电弹常数的测定

本文讨论了由作者首次人工合成的新的钨青铜结构铁电单晶(K_0.20Na_0.20Sr_0.60Ba_0.20)Nb₂O₆全部电弹常数的测量方法和测量程序。第一次发表了该晶体的全部电弹常数及电-机耦合系数等共53个数据。绝大多数的数据是按IRE标准进行测量的。采用了(zxl)45°切片的厚度切变振动模式和(xzt)45°棒的长度扩张模式来测定弹性系数s₆₆^D和s₁₃^D。对实验过程引起的测量误差进行了讨论。 关键词：     

Sr0.61Ba0.39Nb2O6薄膜的电光特性

用激光脉冲沉积(PLD)法在MgO(001)衬底上成功地生长、制备出了外延Sr_0.61Ba_0.39Nb₂O₆(SBN61)电光薄膜;通过SBN61电光薄膜椭偏光谱测量的分析研究,得到了SBN61电光薄膜的光学常数;通过电致双折射方法对生长在(001)MgO衬底上的SBN61薄膜的电光性能进行了测量研究,发现SBN61电光薄膜电致双折射的变化Δn与所加电场E成平方关系,其二次电光系数R=0.21×10^-16(m/V)²。     

POSITRON LIFETIME STUDIES OF Y1-xCaxBa2Cu3O7-δ AND Y1-xCaxBa2Cu3-xFexO7-δ

In this paper it is reported that the measurement of the bulk positron lifetime as a function of substitution content x in the temperature range from 70 to 220K was performed in two high-T_c superconducting systems, Y_1-xCa_xBa₂Cu_3-xFe_xO_7-δ and Y_1-xCa_xBa₂Cu₃O_7-δ. It was found that τ_B of both systems decreases significantly with x and the temperature dependence of τ_B is very weak in normal state. In lower temperature region (Tc), a dramatic x-dependent temperature variation of τ_B was observed in the Ca-substituted system: from a decrease of τ_B with decreasing T to an increase of τ_B. With increasing x, the temperature dependence of τ_B remains weak in the Ca- and Fe- substituted systems. Compared with the experimental data of positron lifetime in other substituted systems and the calculation of the positron density distribution, the authors suggest that positron bulk lifetime spectra behaviour can be interpreted by the physical model based on the transfer of electron density between the CuO₂ planes and Cu-O chains. Therefore, the study of positron lifetime spectra provides a useful means to detect the local charge density and to study the correlation between the electronic structure and the high-T_c superconductivity.     

铁电单晶(KxNa1-x)0.4(SryBa1-y)0.8Nb2O6的光学性质和线性电光效应

本文介绍铁电单晶(K_xNa_1-x)_0.4(Sr_yBa_1-y)_0.8Nb₂O₆的光学性质和线性电光效应的测量。实验结果表明,这种晶体具有较大的光学双折射,透光范围由4000?到5.6μm。晶体具有低的线性电光调制的半波电压,其电光调制价值指数n₀³·γ_c高达730×10 关键词：     

LaxZnxBa1-xFe12-xO19铁氧体高温相组成

La_xZn_xBa_1-xFe_12-xO₁₉在高温相区将存在X相和W相,x=0时其居里温度分别为518℃和534℃,x<0.6范围内La,Zn可以在W相中固溶,随x的增加,产生W相的相变温度下降,居里温度θ_f和各向异性场H_A降低,而饱和比磁化强度σ_s增加,各向异性常数基本不变。 关键词：     

PbBi2Nb2O9的晶体结构

PbBi₂Nb₂O₉晶体属正交晶系,空间群为D_2h²³-Fmmm。晶胞参数为a=5.4806(7)?,b=5.4791(7)?,c=25.416(3)?,α=β=γ=90.0(0)°,V=763.2(2)?³。单位晶胞内化学式数z=4,D_obs=7.91g/cm³,D_x=8.26g/cm³ 关键词：     

Y1-xPrxBa2Cu3O7+δ的红外反射谱

测量了温度范围为4.2—300K的Y_1-xPr_xBa₂Cu₃O_7+δ(x=0,0.1,0.2,0.4,0.5,0.61.0)的红外反射谱,发现在低温下Ba模有双模行为,随着x值增大双模强度反转,在YBa₂Cu₃O_7+δ中已被判定为Y模的位于194cm^-1的反射峰的位置与Pr的含量无关,即用Pr部份或全部替代Y时此峰不发生频移。建议Pr在Y_1-xPr_xBa₂Cu₃O_7+δ,中是正4价,Pr的替代使原来可移动的空穴被定域在Pr的周围,使超导电性受到压制。 关键词：     

YbxY1-xBa2Cu3O7-y的超导载流特性

本文系统地研究了Yb_xY_1-xBa₂Cu₃O_7-y系统的微结构、超导临界温度以及超导载流特性。发现:随着Yb含量的增大,样品的超导临界温度没有很大变化,但晶粒度逐渐减小,超导临界电流密度系统地下降。作者认为:在这种弱连接颗粒超导体中,细化晶粒无助于提高其临界电流密度。 关键词：     

Gd1-xCaxBa2Cu3O7-y高温超导体压力效应的研究

研究了Ｇｄ_1-xＣａ_xＢａ₂Ｃｕ₃Ｏ_7-y（０．０≤Ｘ≤０．２０）高温超导体在常压和高压下的超导电性在１－３００Ｋ温度范围内，利用Ｂｒｉｄｇｍａｎ对顶砧获得压力达９．０ＧＰａ，测量了（Ｘ＝０．１０，０．１５，０．２０）样品的ｄＴ_c／ｄｐ分别为７．６８，７．８和４．４６Ｋ／ＧＰａ。发现Ｔ_c的压力导数随着ｃａ²⁺含量的增加而下降，分析了氧含量对Ｔ_c和ｄＴ_c／ｄＰ的影响．利用常压下晶格参数精修值和阳离子与氧离子间距随压力的改变，说明ＣｕＯ₂面在超导电性上的作用，用ＣｕＯ₂面之间耦合解释Ｔ_c（Ｐ）曲线的非线性关系。 关键词：     

LiNbO3和LiTaO3单晶体中亚晶界位错结构的研究

本文应用透射法和超显微法对用金缀饰后的LiNbO₃和LiTaO₃单晶体进行了直接观测,观察到两种晶体中亚晶界的三维面貌,对亚晶界进行了极图分析,并进一步用Frank公式进行了定量验证。通过对位错网及三叉亚晶界的分析,表明该类晶体中存在的位错的Burgers矢量是:最短点阵平移矢量——六角晶胞的基矢<1210>,次短点阵平移矢量——菱胞基矢1/3<0111>,以及再次短点阵平移矢量——菱胞短体对角线分1/3<2021>。 关键词：     

PrxLa1-xP5O14的发光理论和浓度效应

本文利用Judd-Ofelt理论求得PrP₅O₁₄晶体的振子强度参数Q₂,比较了计算和实验的振子强度,计算了³P₁,³P₀,¹D₂和¹G₄能级的电偶极和磁偶极辐射跃迁几率及¹D₂→¹G₄和³H₄→³F₄能级对间的多极矩耦合的无辐射迁移几率。讨论了¹D₂能级发射强度的浓度效应。并且,给出¹D₂能级发射强度的表达式和强度随着浓度和单位时间内激发光引起的³H₄到¹D₂跃迁的诱导跃迁几率的变化图。 关键词：     

直拉法生长的LiNbO3单晶体中的生长条纹和铁电畴组态间的对应关系

对应于旋转条纹和功率条纹,观测到晶体中铁电畴组态的相应变化,确定了旋转条纹与铁电畴组态间的一一对应关系,利用扫描电子显微镜中的X射线能谱分析测定了旋转条纹中的溶质浓度分布,得到了溶质浓度梯度决定了铁电畴组态的结论,自发极化与溶质浓度梯度间的耦合首次得到了实验证实。 关键词：     

Y1-xPrxBa2Cu3O7-δ体系中的离子价键特性与超导电性

基于中子散射实验结果,应用键价计算方法研究了Y_1-xPr_xBa₂Cu₃O_7-δ(x=0,0.2,0.4,0.6)体系中离子的价键特性。对Cu(1),Cu(2)及Y(Pr)的键价和计算结果表明,Cu(2)的键价和与超导临界温度(T_c)之间存在着强烈的关朕。在氧含量基本保持不变的情况下,随Pr含量的增加,体系中电荷分布发生改变,Cu(1),Cu(2)的键价和下降,Y(Pr)的键价 关键词：     

STRUCTURE AND SUPERCONDUCTIVITY OF Mg1-xLixB2

The effects of the substitution of Li for Mg in Mg_1-xLi_xB₂(x=0,0.1,0.2) on their structure and superconductivity have been investigated. It has been found by X-ray diffraction that the substitution of Li for Mg with x=0.1 and 0.2 does not cause phase transformation in these samples. However,the measurements of temperature-dependent normalized magnetization indicate the loss of superconductivity with the increase of Li content in these samples.     

用会聚束电子衍射测定LiZnTa3O9,LiCaTa3O9的对称性

本文用会聚束电子衍射方法测定了我们生长的新晶体LiZnTa₃O₉和LiCaTa₃O₉的对称性,得出LiZnTa₃O₉晶体属三方晶系,点阵参数a=0.557nm,a=56.12°,点群为3m,空间群为R3c。LiCaTa₃O₉晶体属四方晶系,点阵参数a=0.778nm,c=0.783nm,点群为4/mmm。 关键词：     

Impurity effect on the Raman spectra of Sr0.6Ba0.4Nb2O6

Impurity effect on the rare earth ion doped Sr_0.6Ba_0.4Nb₂O₆(SBN40) was studied at room temperature. Doping the rare earth ions of Pr³⁺ or Nd³⁺ changed the Raman profile: spectral broadening, central frequency shifts and relative intensity decreasing. Two reasons are considered according to the ferroelectric and optical properties of the rare earth ion doped SBN40: impurity-induced crystal disorder and the crystal structure change. SBN40 is the general disorder crystal and the disorder which is enhanced by doping the rare earth ion is especially strong along the x?y plane of the material compared with that along the polar C-axis.     

Improved microstructure, dielectric and ferroelectric properties of microwave-sintered Sr0.5Ba0.5Nb2O6

Ferroelectric strontium barium niobate (SBN) powder was synthesized by solid-state route. The green compacts were sintered in the temperature range 1250–1350 °C in a microwave furnace. The microstructural study, using SEM, revealed the grain size in the range 2–20 μm without microcracks, depending on the sintering temperature. This is in contrast to that obtained conventionally for sintered SBN powder synthesized by solid-state route, which resulted in duplex microstructure with microcracks [N.S. VanDamme, A.E. Sutherland, L. Jones, K. Bridger, S.R. Winzer, J. Am. Ceram. Soc. 74 (1991) 1785; P.K. Patro, A.R. Kulkarni, C.S. Harendranath, Ceram. Int. 30 (2004) 1405; P.K. Patro, Trans. Ind. Inst. Metals 59 (2006) 229]. Impedance analyzer and ferroelectric hysteresis loop tracer were used for the dielectric, ferroelectric, I–V and electric fatigue measurements. Microwave sintering also resulted in a dielectric maxima ε_max 2590 at 1 kHz (compared to 1103 for conventional sintering [P.K. Patro, A.R. Kulkarni, C.S. Harendranath, Ceram. Int. 30 (2004) 1405]) for the sintering temperature of 1350 °C. Similar improvement in microwave-sintered SBN was observed depending on their sintering condition. The origin of this difference is attributed to microstructural differences arising from difference in heating method. In this paper the observed dielectric and ferroelectric behavior have been correlated with different sintering conditions and consequent microstructure due to microwave sintering.