Mechanistic Insights into the Luminescent Sensing of Organophosphorus Chemical Warfare Agents and Simulants Using Trivalent Lanthanide Complexes

Organophosphorus chemical warfare agents (OP CWAs) are potent acetylcholinesterase inhibitors that can cause incapacitation and death within minutes of exposure, and furthermore are largely undetectable by the human senses. Fast, efficient, sensitive and selective detection of these compounds is therefore critical to minimise exposure. Traditional molecular‐based sensing approaches have exploited the chemical reactivity of the OP CWAs, whereas more recently supramolecular‐based approaches using non‐covalent interactions have gained momentum. This is due, in part, to the potential development of sensors with second‐generation properties, such as reversibility and multifunction capabilities. Supramolecular sensors also offer opportunities for incorporation of metal ions allowing for the exploitation of their unique properties. In particular, trivalent lanthanide ions are being increasingly used in the OP CWA sensing event and their use in supramolecular sensors is discussed in this Minireview. We focus on the fundamental interactions of simple lanthanide systems with OP CWAs and simulants, along with the development of more elaborate and complex systems including those containing nanotubes, polymers and gold nanoparticles. Whilst literature investigations into lanthanide‐based OP CWA detection systems are relatively scarce, their unique and versatile properties provide a promising platform for the development of more efficient and complex sensing systems into the future.     

应用热脱附-气相色谱质谱法测定空气中化学毒剂模拟剂

采用Tenax-TA热脱附采样管(Tube)主动采样,以热脱附仪结合气相色谱质谱(GC-MS)联用仪为分析手段,建立了空气中4种化学毒剂模拟剂(1,2-二氯乙烷、N,N-二甲基乙酰胺、磷酸三甲酯和甲基磷酸二甲酯)的快速分析方法。结果表明,4种模拟剂在1～100 ng/tube范围内线性关系良好,相关系数均大于0.99,平均加标回收率为82%～112%,检出限为0.13～0.26 ng/tube,相对标准偏差小于15%。     

Ultra‐Fast Degradation of Chemical Warfare Agents Using MOF–Nanofiber Kebabs

The threat associated with chemical warfare agents (CWAs) motivates the development of new materials to provide enhanced protection with a reduced burden. Metal–organic frame‐works (MOFs) have recently been shown as highly effective catalysts for detoxifying CWAs, but challenges still remain for integrating MOFs into functional filter media and/or protective garments. Herein, we report a series of MOF–nanofiber kebab structures for fast degradation of CWAs. We found TiO₂ coatings deposited via atomic layer deposition (ALD) onto polyamide‐6 nanofibers enable the formation of conformal Zr‐based MOF thin films including UiO‐66, UiO‐66‐NH₂, and UiO‐67. Cross‐sectional TEM images show that these MOF crystals nucleate and grow directly on and around the nanofibers, with strong attachment to the substrates. These MOF‐functionalized nanofibers exhibit excellent reactivity for detoxifying CWAs. The half‐lives of a CWA simulant compound and nerve agent soman (GD) are as short as 7.3 min and 2.3 min, respectively. These results therefore provide the earliest report of MOF–nanofiber textile composites capable of ultra‐fast degradation of CWAs.     

Fluorescent Cadmium Bipillared-Layer Open Frameworks: Synthesis,Structures, Sensing of Nitro Compounds,and Capture of Volatile Iodine

Fluorescent Cd metal–organic frameworks (MOFs), [Cd₂(dicarboxylate)₂(NI-bpy-44)₂] (dicarboxylate=benzene-1,4-dicarboxylate (1,4-bdc, 1 ), 2-bromobenzene-1,4-dicarboxylate (Br-1,4-bdc, 2 ), 2-nitrobenzene-1,4-dicarboxylate (NO₂-1,4-bdc, 3 ), biphenyl-4,4′-dicarboxylate (bpdc, 4 ); NI-bpy-44=N-(pyridin-4-yl)-4-(pyridin-4-yl)-1,8-naphthalimide)), featuring non- and twofold interpenetrating pcu -type bipillared-layer open structures with sufficient free voids of 58.4, 51.4, 51.5, and 41.4 %, respectively, have been hydro(solvo)thermally synthesized. MOFs 1 – 4 emitted solid-state blue or cyan fluorescence emissions at 447±7 nm, which mainly arose from NI-bpy-44 and are dependent on the incorporated solvents. After immersing the crystalline samples in different solvents, that is, H₂O and DMSO ( 1 and 2 ) as well as nitrobenzene and phenol ( 1 – 4 ), they exhibited a remarkable fluorescence quenching effect, whereas o-xylene and p-xylene ( 4 ) caused significant fluorescence enhancement. The sensing ability of MOFs 1 – 4 toward nitro compounds carried out in the vapor phase showed that nitrobenzene and 2-nitrophenol displayed detectable fluorescence quenching with 1 , 2 , and 4 whereas 4-nitrotoluene was an effective fluorescence quencher for 1 and 2 ; this is most likely attributed to their electron-deficient properties and higher vapor pressures. Moreover, MOFs 1 – 4 are highly reusable for quick capture of volatile iodine, as supported by clear crystal color change and also by immense fluorescence quenching responses owing to the donor–acceptor interaction. Low-pressure CO₂ adsorption isotherms indicate that activated materials 1′ – 4′ are inefficient at taking up CO₂.     

Dynamic Coordination Chemistry of Fluorinated Zr-MOFs: Synthetic Control and Reassembly/Disassembly Beyond de Novo Synthesis to Tune the Structure and Property

Known for excellent stability, porosity and functionality, the high-valent Zr⁴⁺ metal–organic frameworks (Zr-MOFs) still meets synthetic challenge in modulating the strength of Zr-O_carboxylate linkage. Herein we explore the unusual coordination dynamics of fluorinated Zr-MOFs by designing two trifluoromethyl modified ligands with distinct geometry preference to form a family of thermodynamic and kinetic products. The low-connecting kinetic Zr-MOFs possess substitutable coordination sites to endow Zr₆-cluster with extra dynamic behaviors, thus opening a post-synthetic pathway to sequential reassembly/disassembly processes. Comprehensive factors, including ligand geometry, Zr₆-cluster connectivity, acid modulator and reaction temperature/concentration, have been studied for controllable syntheses. The stability, hydrophobicity and gas adsorption/separation properties of obtained Zr-MOFs are explored. This work sheds light on the understanding of the dynamic coordination chemistry of Zr-MOFs beyond strong Zr−O bond, which poses a versatile platform for modification and functionalization of Zr-MOFs.     

Ultrasonic-Assisted Linker Exchange (USALE): A Novel Post-Synthesis Method for Controlling the Functionality,Porosity, and Morphology of MOFs

The introduction of organic ligands into metal–organic frameworks (MOFs) with a specific topology and that cannot be attained by direct synthesis is a big challenge. To meet this challenge, different ligand exchange/incorporation methods have been employed. Here, a new method, called ultrasonic-assisted linker exchange (USALE), has been developed to overcome the above-mentioned problems. USALE is a novel method for ligand exchange based on the use of ultrasonic waves. The temperature and pressure caused by the USALE method in microscopic zones are so intense that the linker exchange process is much faster than with other methods. In addition to saving time during synthesis, the use of the USALE method leads to a higher surface area and pore volume compared with other methods such as solvent-assisted linker exchange (SALE). In this way, improved gas adsorption capacity has been achieved for daughter frameworks synthesized by the USALE method. By using the USALE method, we have transformed a nonporous and easy-to-synthesize TMU framework ([Zn(OBA)(BPDB)0.5]n ⋅ 2DMF (TMU-4), in which H2OBA=4,4′-oxybis(benzoic acid) and BPDB=1,4-di(4-pyridyl)-2,3-diaza-1,3-butadiene) into another porous framework ([Zn(OBA)(H2DPT)0.5]n ⋅ DMF (TMU-34), in which H2DPT=3,6-di(4-pyridyl)-1,4-dihydro-1,2,4,5-tetrazine) that otherwise requires a relatively long time to synthesize. In addition to reducing the synthesis time for TMU-34 (in comparison with both direct sonochemical synthesis and the indirect SALE method), the data obtained revealed that the daughter TMU-34 framework synthesized by the USALE method has a higher surface area and accessible pore volume than TMU-34 frameworks synthesized by SALE and direct methods. The application of SALE-TMU-34 and USALE-TMU-34 in a catalytic Henry condensation reaction and Congo Red adsorption experiments showed that the higher porosity of USALE-TMU-34 leads to a higher turn-over frequency and saturation capacity compared with SALE-TMU-34.     

Microwave‐Assisted Synthesis of HKUST‐1 and Functionalized HKUST‐1‐@H3PW12O40: Selective Adsorption of Heavy Metal Ions in Water Analyzed with Synchrotron Radiation

A simple, rapid and efficient synthesis of the metal‐organic framework (MOF) HKUST‐1 [Cu₃(1,3,5‐benzene‐tri‐carboxilic‐acid)₂] by microwave irradiation is described, which afforded a homogeneous and highly selective material. The unusually short time to complete the synthesis by microwave irradiation is mainly attributable to rapid nucleation rather than to crystal growth rate. Using this method, HKUST‐1‐MW (MW=microwave) could be prepared within 20 min, whereas by hydrothermal synthesis, involving conventional heating, the preparation time is 8 h. Work efficiency was improved by the good performance of the obtained HKUST‐1‐MW which exhibited good selective adsorption of heavy metal ions, as well as a remarkably high adsorption affinity and adsorption capacity, but no adsorption of Hg²⁺ under the same experimental conditions. Of particular importance is the preservation of the structure after metal‐ion adsorption, which remained virtually intact, with only a few changes in X‐ray diffraction intensity and a moderate decline in surface area. Synthesis of the polyoxometalate‐containing HKUST‐1‐MW@H₃PW₁₂O₄₀ afforded a MOF with enhanced stability in water, due to the introduced Keggin‐type phosphotungstate, which systematically occluded in the cavities constituting the walls between the mesopores. Different Cu/W ratios were investigated according to the extrusion rate of cooper ions concentration, without significant structural changes after adsorption. The MOFs obtained feature particle sizes between 10–20 μm and their structures were determined using synchrotron‐based X‐ray diffraction. The results of this study can be considered important for potentially wider future applications of MOFs, especially to attend environmental issues.     

3D Electron-Rich ZIF-67 Coordination Compounds Based on 2-Methylimidazole: Synthesis,Characterization and Effect on Thermal Decomposition of RDX,HMX, CL-20, DAP-4 and AP

ZIF-67 is a three-dimensional zeolite imidazole ester framework material with a porous rhombic dodecahedral structure, a large specific surface area and excellent thermal stability. In this paper, the catalytic effect of ZIF-67 on five kinds of energetic materials, including RDX, HMX, CL-20, AP and the new heat-resistant energetic compound DAP-4, was investigated. It was found that when the mass fraction of ZIF-67 was 2%, it showed excellent performance in catalyzing the said compounds. Specifically, ZIF-67 reduced the thermal decomposition peak temperatures of RDX, HMX, CL-20 and DAP-4 by 22.3 °C, 18.8 °C, 4.7 °C and 10.5 °C, respectively. In addition, ZIF-67 lowered the low-temperature and high-temperature thermal decomposition peak temperatures of AP by 27.1 °C and 82.3 °C, respectively. Excitingly, after the addition of ZIF-67, the thermal decomposition temperature of the new heat-resistant high explosive DAP-4 declined by approximately 10.5 °C. In addition, the kinetic parameters of the RDX+ZIF-67, HMX+ZIF-67, CL-20+ZIF-67 and DAP-4+ZIF-67 compounds were analyzed. After the addition of the ZIF-67 catalyst, the activation energy of the four energetic materials decreased, especially HMX+ZIF-67, whose activation energy was approximately 190 kJ·mol⁻¹ lower than that reported previously for HMX. Finally, the catalytic mechanism of ZIF-67 was summarized. ZIF-67 is a potential lead-free, green, insensitive and universal EMOFs-based energetic burning rate catalyst with a bright prospect for application in solid propellants in the future.     

Nanoparticles: Properties,applications and toxicities

This review is provided a detailed overview of the synthesis, properties and applications of nanoparticles (NPs) exist in different forms. NPs are tiny materials having size ranges from 1 to 100 nm. They can be classified into different classes based on their properties, shapes or sizes. The different groups include fullerenes, metal NPs, ceramic NPs, and polymeric NPs. NPs possess unique physical and chemical properties due to their high surface area and nanoscale size. Their optical properties are reported to be dependent on the size, which imparts different colors due to absorption in the visible region. Their reactivity, toughness and other properties are also dependent on their unique size, shape and structure. Due to these characteristics, they are suitable candidates for various commercial and domestic applications, which include catalysis, imaging, medical applications, energy-based research, and environmental applications. Heavy metal NPs of lead, mercury and tin are reported to be so rigid and stable that their degradation is not easily achievable, which can lead to many environmental toxicities.