37单元双压电片变形镜板条激光光束净化

为了校正板条激光器输出光束波前像差,改善输出光束质量,提出了基于37单元双压电片变形镜的板条激光光束净化系统。采用柱面反射式单向扩束器使主振荡功率放大结构板条激光器输出光束尺寸与37单元双压电片变形镜有效口径相匹配,利用随机并行梯度下降算法控制双压电片变形镜面形,进行波前像差闭环校正,校正后光束远场归一化桶中功率提高到净化前的2~3倍。     

37单元双压电片变形镜板条激光光束净化

为了校正板条激光器输出光束波前像差,改善输出光束质量,提出了基于37单元双压电片变形镜的板条激光光束净化系统。采用柱面反射式单向扩束器使主振荡功率放大结构板条激光器输出光束尺寸与37单元双压电片变形镜有效口径相匹配,利用随机并行梯度下降算法控制双压电片变形镜面形,进行波前像差闭环校正,校正后光束远场归一化桶中功率提高到净化前的2~3倍。     

High-speed machining of glass materials by laser-induced plasma-assisted ablation using a 532-nm laser

+ :YAG laser (532 nm). The plasma generated from a silver (Ag) target by the laser irradiation effectively assists in ablation of the fused quartz substrate by the same laser beam, although the laser beam is transparent to the substrate. A grating with a cross-sectional shape like a square-wave (period ≈ 20 μm) is achieved using the mask projection technique. The ablation rate reaches several tens nm/pulse. In addition, LIPAA is applied to high-speed hole drilling (700 μm in diameter) of fused-quartz (0.5 mm thick) and Pyrex glass (0.5 mm thick). Received: 25 May 1998/Accepted: 19 June 1998     

1.9-W flash-lamp-pumped solid-state 266-nm ultraviolet laser

Deep ultraviolet lasers have various applications in industries and scientific researches. For 266-nm ultra- violet （UV） laser generation, the good beam quality of 1064-nm laser and the elimination of gray-tracking effect of KTP crystal are two key factors. Using a dynamically stable resonator design, 1064-nm laser with an average power of 52 W is realized with repetition rate of 16 kHz. The measured M^2 factor characterizing the beam quality is 1.5. By the elimination of gray-tracking effect of KTP crystal, an 18-W green laser is realized with the M2 factor of 1.6. Using a BBO crystal for the fourth harmonic generation, a 1.9-W 266-nm UV laser is achieved.     

Cleaning of artificially soiled paper with 532-nm nanosecond laser radiation

Cleaning of paper is a challenging task due to the fact that a contamination should be removed and a fragile organic original material has to be preserved. Pulsed laser cleaning of artificially soiled Whatman© filter paper samples serving as models for historical paper was performed. Different cleaning strategies employing 8-ns laser pulses at 532 nm wavelength were applied to clean paper avoiding undesired effects like discoloration (yellowing) and mechanical deterioration of the substrate. Multi shot experiments with low-energy pulses were compared with single pulse investigations utilizing high pulse energies achieving a constant energy load incident on the samples in both cases. The cleaning efficiency and possible yellowing effects were evaluated by means of a multi spectral imaging system. An extensive microscopic analysis of the cleaned parts of the samples provided insight into the remaining soiling on the surface and in the bulk of the paper material after laser treatment. As a reference, a hard and a soft eraser were used to clean the samples.     

Generation of custom modes in a Nd:YAG laser with a semipassive bimorph adaptive mirror

Custom modes at a wavelength of 1064 nm were generated with a deformable mirror. The required surface deformations of the adaptive mirror were calculated with the Collins integral written in a matrix formalism. The appropriate size and shape of the actuators as well as the needed stroke were determined to ensure that the surface of the controllable mirror matches the phase front of the custom modes. A semipassive bimorph adaptive mirror with five concentric ring-shaped actuators and one defocus actuator was manufactured and characterised. The surface deformation was modelled with the response functions of the adaptive mirror in terms of an expansion with Zernike polynomials. In the experiments the Nd:YAG laser crystal was quasi-CW pumped to avoid thermally induced distortions of the phase front. The adaptive mirror allows to switch between a super-Gaussian mode, a doughnut mode, a Hermite-Gaussian fundamental beam, multi-mode operation or no oscillation in real time during laser operation. PACS 42.60.Jf; 42.60.Da; 42.60.By     

532 nm脉冲激光辐照CCD实验研究

采用532 nm,10 ns的脉冲激光对面阵CCD进行辐照实验,对每一阶段的实验现象和电路层面的破坏机理进行了深入分析,根据实验现象,把脉冲激光对CCD的硬破坏分为3个阶段：第1阶段在低能量密度激光辐照下,被破坏的CCD局部出现无法恢复的白色盲点,但其它部分仍可正常成像;第2阶段CCD探测器受到激光辐照后,在光斑处的时钟线方向出现白色竖直亮线,亮线处无法正常成像且激光辐照撤去后无法恢复;第3阶段受高能量密度激光辐照后,CCD完全失效,无法恢复成像。针对CCD的饱和及恢复阶段,利用Matlab编码对分辨力靶板的成像数据进行处理,分析了激光辐照CCD对饱和像元数和对比度的影响。结果表明：当CCD受到激光辐照时,饱和像元数迅速增多,图像对比度迅速下降为零,激光脉冲消失后,整个CCD成像亮度下降,饱和像元数迅速下降为零,经过一段时间后CCD又恢复至线性工作状态,激光的能量密度越高,CCD恢复所需的时间就越长。研究还发现：当恢复时间超过0.6 s,CCD出现不可恢复的白色条带,严重影响成像质量。     

Graphene saturable absorber mirror for ultra-fast-pulse solid-state laser

High-quality graphene sheets with lateral size over 20 μm have been obtained by bath sonicating after subjecting the wormlike graphite marginally to mixed oxidizer. To date, to our knowledge, they are the largest graphene sheets prepared by exfoliation in the liquid phase. A saturable absorber mirror was fabricated based on these sheets. We exploited it to realize mode-locking operation in a diode-pumped Nd:GdVO(4) laser. A pulse duration of 16 ps was produced with an average power of 360 mW and a highest pulse energy of 8.4 nJ for a graphene mode-locked laser.     

532-nm picosecond pulse generated in a passively mode-locked Nd:YVO_4 laser

A diode-pumped continuous-wave （CW） mode-locked Nd：YVO4/KTP green laser with semiconductor saturable absorber mirror （SESAM） is demonstrated. The maximum output power of CW mode-locked green laser is obtained to be 552 mW at the incident pump power of 7.25 W, corresponding to an opticai-optical conversion efficiency of about 7.6%. The 532-nm CW mode-locked pulse duration is estimated to be about 8.4 ps with the repetition rate of 87 MHz.     

Surface hardening of titanium by pulsed Nd:YAG laser irradiation at 1064- and 532-nm wavelengths in nitrogen atmosphere

The surface hardness of titanium modified by laser irradiation at different wavelengths in nitrogen atmosphere was investigated. Further, surface characteristics such as morphology, chemical state, and chemical composition in the depth direction were also studied. The size and depth of the craters observed in the laser-irradiated spots increased monotonically with an increase in the laser power. Furthermore, the crater formed by the 532-nm laser was deeper than that formed by the 1064-nm laser for the same laser power. Laser power beyond a certain threshold value was required to obtain a titanium nitride layer. When the laser power exceeds the threshold value, a titanium nitride layer of a few tens of nanometers in thickness was formed on the substrate, whereas a titanium oxide layer containing small amounts of nitrogen was formed when the laser power is below the threshold value. Thus, it was shown that laser irradiation using appropriate laser parameters can successfully harden a titanium substrate, and the actual hardness of the titanium nitride layer, measured by nanoindentation, was approximately five times that of an untreated titanium surface.     

双压电片变形镜像差校正能力

利用实测影响函数,通过数值仿真分析了有效孔径、光束入射角度对于20单元双压电片变形镜像差校正能力的影响。仿真结果表明:有效孔径为16 mm时,变形镜对于各阶像差的校正能力较好;而随着光束入射到变形镜角度的增大,变形镜对于像差的校正精度与校正幅度都会出现下降,但是如果能够将入射角控制在25以内,入射角度对变形镜的像差校正能力影响不大。     

2.5-W, continuous-wave, 629-nm solid-state laser source

We report an efficient, high-power, cw, 629-nm laser source based on a diode-pumped Nd:YAG laser and a periodically poled lithium niobate (PPLN) frequency converter. This device integrates two separate frequency-conversion steps in a single crystal, taking advantage of the ability to fabricate PPLN with nearly arbitrary grating periods and phase-matching temperatures. This device uses a single PPLN crystal that has two grating regions in series. The first region quasi-phase matches a standard optical parametric oscillator process (1064nm?1540nm +3450nm), and the second region quasi-phase matches a sum-frequency process whereby the pump and the signal light make red light (1064nm+1540nm ?629nm). Using a four-mirror ring cavity, we were able to convert 21% of the 1064-nm pump to 629-nm output, yielding 2.5W of red output with 11.8W of input.     

双压电片变形镜像差校正能力

利用实测影响函数,通过数值仿真分析了有效孔径、光束入射角度对于20单元双压电片变形镜像差校正能力的影响。仿真结果表明：有效孔径为16 mm时,变形镜对于各阶像差的校正能力较好;而随着光束入射到变形镜角度的增大,变形镜对于像差的校正精度与校正幅度都会出现下降,但是如果能够将入射角控制在25以内,入射角度对变形镜的像差校正能力影响不大。     

An 8-W diode side pumped solid-state 593-nm laser

We report a double z-type folded plane-plane symmetrical cavity diode side pumped solid state yellow-orange laser at 593 nm by using intracavity sum-frequency mixing. By carefully designing the cavity and employing several techniques to increase sum-frequency efficiency, a Q-switched yellow-orange laser source, with an average output power of 8 W, a beam quality factor M ² = 4.86, and a repetition rate of 8 kHz is developed. In this paper, we first use 1338 and 1064 nm emissions of Nd:YAG crystal to generate 593 nm yellow-orange laser beam by intracavity sum-frequency mixing (SFM).     

Theory of active-passive mode-locking of solid-state lasers using a nonlinear mirror

The theory of active-passive mode-locked solid-state lasers is developed where the passive mode-locking is achieved by a nonlinear mirror. Steady-state cw numerical solutions are analyzed in detail for the case of a Nd: YAG laser. The steady-state pulse duration can be reduced by an order of magnitude as compared to the pure active mode-locking regime.On leave from Department of Quantum Electronics, Faculty of Physics, University of Sofia, BG-1126 Sofia, Bulgaria     

Interaction between 193-nm pulsed laser radiation and α-alumina

The threshold power density of 15-ns laser pulses with a wavelength 193 nm is determined for basic modes of interaction between the radiation and α-alumina. As power density Q on the target varying in the range 0.001–100 MW/cm² increases, first the interaction mechanism changes from single-photon interaction to two-photon interaction at Q ≈ 0.1 MW/cm². At Q ≈ 5 MW/cm², the material sublimates and then the sublimation products ionize at Q ≈ 15 MW/cm². At Q ≈ 100 MW/cm², the material is removed from the surface at a rate of ≈ 10 nm per pulse.     

Phase-coherent optical frequency division by 3 of 532-nm laser light with a continuous-wave optical parametric oscillator

Phase-locked 3:1 division of an optical frequency was achieved with a continuous-wave monolithic optical parametric oscillator (OPO) pumped by a 532-nm Nd:YAG laser, by use of 5% MgO-doped LiNbO(3) as a nonlinear optical crystal. The OPO generated signal light (798 nm) with 4-mW power and idler light (1596 nm) with 3-mW power for a pump power of 68 mW. Approximately 2microW of second harmonics (SH's) of the idler light was produced by external-cavity-enhanced SH generation by use of a periodically poled LiNbO(3) crystal. The beat signal between the signal light and the SH of the idler light was observed with a signal-to-noise ratio of 40 dB at a 10-kHz bandwidth and was successfully phase locked to a signal from a synthesizer through the electro-optic effect of the crystal.     

Repetitively pulsed solid-state laser system with SBS pulse compression

A repetitively pulsed solid-state laser system with a new version of a pulse compression scheme based on stimulated Brillouin scattering is proposed. The scheme allows us to work in a wide energy range from 100 mJ to several Joules, with a compressed pulse as short as 150–300 ps.