Aerosol generation and measurement of multi-wall carbon nanotubes

Mass production of some kinds of carbon nanotubes (CNT) is now imminent, but little is known about the risk associated with their exposure. It is important to assess the propensity of the CNT to release particles into air for its risk assessment. In this study, we conducted aerosolization of a multi-walled CNT (MWCNT) to assess several aerosol measuring instruments. A Palas RBG-1000 aerosol generator applied mechanical stress to the MWCNT by a rotating brush at feed rates ranging from 2 to 20 mm/h, which the MWCNT was fed to a two-component fluidized bed. The fluidized bed aerosol generator was used to disperse the MWCNT aerosol once more. We monitored the generated MWCNT aerosol concentrations based on number, area, and mass using a condensation particle counter and nanoparticle surface area monitor. Also we quantified carbon mass in MWCNT aerosol samples by a carbon monitor. The shape of aerosolized MWCNT fibers was observed by a scanning electron microscope (SEM). The MWCNT was well dispersed by our system. We found isolated MWCNT fibers in the aerosols by SEM and the count median lengths of MWCNT fibers were 4–6 μm. The MWCNT was quantified by the carbon monitor with a modified condition based on the NIOSH analytical manual. The MWCNT aerosol concentration (EC mass base) was 4 mg/m³ at 2 mm/h in this study.     

The feasibility of producing MWCNT paper and strong MWCNT film from VACNT array

This study sought to produce carbon nanotube (CNT) pulp out of extremely long, vertically aligned CNT arrays as raw materials. After high-speed shearing and mixing nitric acid and sulfuric acid, which served as the treatment, the researchers produced the desired pulp, which was further transformed into CNT paper by a common filtration process. The paper’s tensile strength, Young’s modulus and electrical conductivity were 7.5 MPa, 785 MPa and 1.0×10⁴ S/m, respectively, when the temperature of the acid treatment was at 110°C. Apart from this, the researchers also improved the mechanical property of CNT paper by polymers. The CNT paper was soaked in polyethylene oxide, polyvinyl pyrrolidone, and polyvinyl alcohol (PVA) solution, eventually making the CNT/PVA film show its mechanical properties, which increased, while its electrical conductivity decreased. To diffuse the polymer into the CNT paper thoroughly, the researchers used vacuum filtration to fabricate a CNT/PVA film by penetrating PVA into the CNT paper. After a ten-hour filtration, the tensile strength and Young’s modulus of CNT/PVA film were 96.1 MPa and 6.23 GPa, respectively, which show an increase by factors of 12 and 7, respectively, although the material’s electrical conductivity was lowered to 0.16×10⁴ S/m.     

光纤波导色散的比例性质研究

基于麦克斯韦方程组的比例性质,讨论了光纤波导色散的比例性质,并对普通光纤、Bragg光纤和光子晶体光纤的波导色散进行了理论研究。以Bragg光纤为例,提出了一种根据波导色散的比例性质灵活设计光纤色散特性的方法。     

Responses of "lower-spontaneous-rate" auditory-nerve fibers to speech syllables presented in noise. I: General characteristics.

Responses of auditory-nerve fibers in anesthetized cats to nine different spoken stop- and nasal-consonant/vowel syllables presented at 70 dB SPL in various levels of speech-shaped noise [signal-to-noise (S/N) ratios of 30, 20, 10, and 0 dB] are reported. The temporal aspects of speech encoding were analyzed using spectrograms. The responses of the "lower-spontaneous-rate" fibers (less than 20/s) were found to be more limited than those of the high-spontaneous-rate fibers. The lower-spontaneous-rate fibers did not encode noise-only portions of the stimulus at the lowest noise level (S/N = 30 dB) and only responded to the consonant if there was a formant or major spectral peak near its characteristic frequency. The fibers' responses at the higher noise levels were compared to those obtained at the lowest noise level using the covariance as a quantitative measure of signal degradation. The lower-spontaneous-rate fibers were found to preserve more of their initial temporal encoding than high-spontaneous-rate fibers of the same characteristic frequency. The auditory-nerve fibers' responses were also analyzed for rate-place encoding of the stimuli. The results are similar to those found for temporal encoding.     

Miscibility and Hydrogen Bonding Interactions in Blends of Poly(hydroxyether ketone) and Poly(4-vinyl pyridine)

The influence of silica nanoparticles on the tensile properties of poly(ethylene terephthalate)(PET) fibers was investigated. The results showed that mechanical properties of PET fibers were improved through nano‐silica incorporation. Two maxima of the modulus‐strain curves of PET/silica nanocomposites (PETS) fibers are always higher than those of pure PET (PET0) fibers. The results of microstructure investigations suggested that the amorphous orientation factor of PETS fibers is higher than that of PET0 fibers. It is suggested that the increase of amorphous orientation factor contributed to the improvement of tensile properties of PET fibers. Considering the difference in modulus‐strain curves of PET0 and PETS fibers, it is believed that the addition of nanoparticles not only improved the amorphous orientation factor but also changed the load units of PET fibers when strained, which also resulted in the improvement of tensile properties.     

Study of adhesion of vertically aligned carbon nanotubes to a substrate by atomic-force microscopy

The adhesion to a substrate of vertically aligned carbon nanotubes (VA CNT) produced by plasmaenhanced chemical vapor deposition has been experimentally studied by atomic-force microscopy in the current spectroscopy mode. The longitudinal deformation of VA CNT by applying an external electric field has been simulated. Based on the results, a technique of determining VA CNT adhesion to a substrate has been developed that is used to measure the adhesion strength of connecting VA CNT to a substrate. The adhesion to a substrate of VA CNT 70–120 nm in diameter varies from 0.55 to 1.19 mJ/m², and the adhesion force from 92.5 to 226.1 nN. When applying a mechanical load, the adhesion strength of the connecting VA CNT to a substrate is 714.1 ± 138.4 MPa, and the corresponding detachment force increases from 1.93 to 10.33 μN with an increase in the VA CNT diameter. As an external electric field is applied, the adhesion strength is almost doubled and is 1.43 ± 0.29 GPa, and the corresponding detachment force is changed from 3.83 to 20.02 μN. The results can be used in the design of technological processes of formation of emission structures, VA CNT-based elements for vacuum microelectronics and micro- and nanosystem engineering, and also the methods of probe nanodiagnostics of VA CNT.     

A comparative study of field emission properties of carbon nanotube films prepared by vacuum filtration and screen-printing

A comprehensive comparative study of electron field emission properties of carbon nanotube (CNT) films prepared by vacuum filtration and screen-printing was carried out. Field emission performance of vacuum filtered CNT films with different filtered CNT suspension volumes was systematically studied, and the optimum electron emission was obtained with a low turn on field of ∼0.93 V/μm (at 1 μA/cm²) and a high field enhancement factor β of ∼9720. Comparing with screen-printed CNT films, vacuum filtered CNT films showed better electron emission performance, longer lifetime, and greater adhesive strength to substrates. This work reveals a potential use of vacuum filtered CNT films as field emission cathodes.     

大电流密度碳纳米管场致发射阴极阵列的研制

 设计了一种由TiN，Al，Fe和牺牲层构成的堆栈式催化剂层结构，采用微波等离子体化学气相沉积法实现碳纳米管阵列高速笔直生长。SEM和TEM结果表明，生长出来的碳纳米管为典型的多壁碳纳米管，长度和直径均匀，排列整齐并垂直于基底，生长速率大于5 μm/min，晶格缺陷少。场致发射测试结果表明：碳纳米管的发射阵列具有良好的电流发射稳定性，最大电流密度大于6 A/cm2。紫外光电子能谱法（UPS）测试出碳纳米管的功函数为4.59 eV，则相应的场致发射陈列的场增强因子大于1 400。     

基于有限元软件分析碳纳米管的最佳阵列密度

利用有限元软件ANSYS,对碳纳米管的最佳阵列密度进行了分析。针对碳纳米管阵列静电场分布的特点,建立了碳纳米管的模型,确定了模型的边界条件。为了便于对计算结果进行对照,在分析时采用的参数是:阵列周期T=2000nm,单根碳纳米管长度L=1μm,顶端半径r=2nm。通过计算得到了单根碳纳米管的场增强因子为321。在长度L和顶端半径r不变的情况下,使用了参数化设计语言,计算了在不同周期(200～4000μm)下碳纳米管场增强因子随周期变化的情况,进一步利用Fowler Nordheim函数得到最佳阵列周期(1600μm)。结果证明,利用有限元软件,其分析过程不仅正确性,而且实用,并且为此类问题的解决提供了一个通用的方法。     

Intrinsic energy loss mechanisms in a cantilevered carbon nanotube beam oscillator

Classical molecular dynamics is applied to study the energy dissipation (the Q factor) of the cantilever-type beam oscillators of single wall and double-walled carbon nanotubes (CNTs). The study finds that the Q factor of the CNT beam oscillator varies with the temperature T following the 1/T(0.36) dependence. For single wall CNT, the Q factor drops from 2 x 10(5) at 0.05 K to 1.5 x 10(3) at 293 K. The study further reveals that the weak interlayer binding strength and the interlayer commensurance significantly increases the energy dissipation in the double-walled CNT oscillator.     

Comparison of the properties of Nextel 720/SiC composites at room temperature and 1300°C

Continuous Nextel 720 fibers reinforced SiC composites with PyC interface are fabricated by LPCVI at 1000°C for 200 h using SiCH₃Cl₃ as precursor. The mechanical properties at RT and 1300°C are measured by three-point bending. The microstructures of the interface are characterized by TEM. The results indicate the composites have the metal-like behavior of fracture, whether they are at RT or high temperature. The RT and 1300°C strengths are 310 MPa and 140 MPa, respectively. The RT and 1300°C strains are 0.32% and 0.12%, respectively. The loss of flexural strength and strain of the Nextel 720/SiC composites at high temperature result from stronger residual thermal stress caused by the mismatch of CTE between fibers and matrix. A gap appears between fibers and PyC interface after the 1300°C test, which could be resulted from 7.7% compressive strain of PyC interface caused by the residual thermal stress and 0.1% sintering shrinkage of Nextel 720 fiber.     

Degradation Studies of Polycaprolactone in Banana Fibers Reinforced Thermoplastics Composites

In this paper we report the fabrication, properties and degradation studies of banana fibers–reinforced thermoplastic polymers. In order to impart hydrophobicity to the fibers and also to concomitantly increase interfacial bond strength, which is a critical factor for obtaining better mechanical properties of composites, banana fibers were treated with sodium hydroxide (5% and 10% for 4 h), sebacoyl chloride (SC) (0.5 g, 4 h), or toluene diisocyanate (TDl) (1.5 mL, 4 h). Mechanical properties of banana fibers treated with TDl were not affected to any significant extent, but there was an increase in tensile strength of fibers treated with sodium hydroxide (NaOH). Deterioration in mechanical properties was observed upon SC treatment. In thermograssimetre analogue (TGA) studies fibers showed initial mass loss (6.5%–9.5%) in the 50–150°C temperature region. Major weight loss occurred above 200°C. Scanning electron microscope (SEM) studies revealed an increase in surface roughness after alkali treatment. High density polyethylene (HDPE) modified by blending with poly (ε‐caprolactone) (80:20 w/w) was used as a thermoplastic matrix. Composites were fabricated by using 1 cm long banana fibers; the weight fraction of fibers was varied from 0.05–0.13. An increase in weight fraction of fibers resulted in an increase in tensile strength and modulus and decrease in elongation at break. Thin sheets and dumbbells were used for enzymatic and chemical hydrolysis degradation tests. The degradation of the material was monitored by weight change and loss of mechanical properties. The enzymatic degradation in (PCL) presence of Pseudomonas cepacia lipase (PCL) gave appreciable weight loss in PCL and blended materials.     

Responses of auditory-nerve fibers to nasal consonant-vowel syllables

Responses of single auditory-nerve fibers in anesthetized cat to spoken nasal consonant-vowel syllables were recorded. Analyses in the form of spectrograms and of three-dimensional spatial-time and spatial-frequency plots were made. Among other features, formant transitions are clearly represented in the fibers' response synchronization properties. During vocalic segments, especially those in /mu/and/ma/, at a stimulus level near 75 dB SPL, a strong dominance in the responses by frequencies near the second formant (F2) is found for most fibers whose characteristic frequencies (CFs) are at or above F2. In contrast, at more moderate levels, the same fibers may show response synchrony to frequencies closer to their own CFs. There are significant differences in the response properties of high and low/medium-spontaneous-rate fibers.     

Improving the field-emission properties of carbon nanotubes by magnetically controlled nickel-electroplating treatment

A novel magnetically controlled Ni-plating method has been developed to improve the field-emission properties of carbon nanotubes (CNTs). The effect of the magnetic field and Ni-electroplating on CNT field-emission properties was investigated, and the results are demonstrated using scanning electron microscopy, J-E and the duration test. After treatment, the turn-on electric field declines from 1.55 to 0.91 V/μm at an emission current density of 100 μA/cm², and the emission current density increases from 0.011 to 0.34 mA/cm² at an electric field of 1.0 V/μm. Both the brightness and uniformity of the CNT emission performance are improved after treatment.     

On the method for determining the true strength of inorganic glasses

The possibility of determining the true structural strength of glass by bending of glass fibers with a defect-free surface is considered. Two methods are compared, viz., the method of transverse three-point bending in which the breaking stress (strength) is determined, and the method of two-point bending in which the breaking strain is determined. In the latter case, the dependence of the elastic modulus on strain is required for determining the breaking stress (strength). The strength measured in three-point bending is compared with the strength calculated from the breaking strain measured in two-point bending. It is shown that the measurements based on these two methods give close values of strength for defect-free silica fibers used as optical waveguides. The observed difference of ～12% in the values of strength is explained by the difference in the loading rates obtained using these two methods. The advantages and disadvantages of these two techniques are analyzed.     

Coupled process of plastics pyrolysis and chemical vapor deposition for controllable synthesis of vertically aligned carbon nanotube arrays

Efficient conversion of waste plastics into advanced materials is of conspicuous environmental, social and economic benefits. A coupled process of plastic pyrolysis and chemical vapor deposition for vertically aligned carbon nanotube (CNT) array growth was proposed. Various kinds of plastics, such as polypropylene, polyethylene, and polyvinyl chloride, were used as carbon sources for the controllable growth of CNT arrays. The relationship between the length of CNT arrays and the growth time was investigated. It was found that the length of aligned CNTs increased with prolonged growth time. CNT arrays with a length of 500 μm were obtained for a 40-min growth and the average growth rate was estimated to be 12 μm/min. The diameter of CNTs in the arrays can be modulated by controlling the growth temperature and the feeding rate of ferrocene. In addition, substrates with larger specific surface area such as ceramic spheres, quartz fibers, and quartz particles, were adopted to support the growth of CNT arrays. Those results provide strong evidence for the feasibility of conversion from waste plastics into CNT arrays via this reported sustainable materials processing.     

Sn/carbon nanotube composite anode with improved cycle performance for lithium-ion battery

Anode material for lithium-ion battery based on Sn/carbon nanotube (CNT) composite is synthesized via a chemical reduction method. The Sn/CNT composite is characterized by thermogravimetry, X-ray diffraction, and transition electron microscopy. The Sn/CNT composite delivers high initial reversible capacity of 630.5 mAh g^?1 and exhibits stable cycling performance with a reversible capacity of 413 mAh g^?1 at the 100th cycle. The enhanced electrochemical performance of the Sn/CNT composite could be mainly attributed to the well dispersion of Sn nanoparticles on CNT and partially filling Sn nanoparticles inside the CNT. It is proposed that the chemical treatment of CNT with concentrated nitric acid, which cuts carbon nanotube into short pieces and increases the amount of oxygen-functional groups on the surface, plays an important role in the anchoring of Sn nanoparticles on carbon nanotube and inhibiting the agglomeration of Sn nanoparticles during the charge–discharge process.     

Characterization and field-emission property of aligned porous carbon nanotube film by hydrogen-ion implantation

To enhance the field emission of carbon nanotube (CNT) films, a novel technique that combines hydrogen-ion implantation used in the silicon-on-insulation smart-cut process and plasma-enhanced chemical vapor deposition was developed to produce an aligned porous carbon nanotube (AP-CNT) film on a Si substrate. All steps in the AP-CNT synthesis were carried out in vacuum, which reduced possible contamination. The morphology and the field-emission properties of the CNT films were investigated and results show that CNT holes with a diameter of 5 m and a depth of 30 m were produced in the AP-CNT film. The alignment of the CNTs is visibly improved. Due to the implantation treatment, the turn-on field of the CNT films decreased from 1.5 to 0.8 V/m, and the emission-current (and dot) density obviously increased. This field-emission improvement may mainly arise from the holes formed in the AP-CNT films. The edges of these holes not only intensified the electron emission but also increase the emission site density of the CNT films. PACS 81.05.Uw; 61.72.Tt; 85.45.Db     

Strength measurements of silica optical fibers under severe environment

Optical fibers are key components in telecommunication technologies. Apart from optical specifications, optical fibers are expected to keep most of their physical properties for 10–20 years in current operating conditions. The reliability and the expected lifetime of optical links are closely related to action of the chemical environment on the silica network. However, the coating also contributes largely to the mechanical properties of the fibers.The aim of this work was to study the strength and the mechanical behavior of the silica optical fibers in an acid environment and with a permanent deformation. A container with ammonium bifluoride acid salt was plunged into hot water at different temperatures (55 and 75 °C). This emitted acid vapors which attacked the optical fibers for a period of 1–18 days. An aging study was performed on silica optical fibers with standard polyacrylate coating and with hermetic carbon coating. A dynamic two-point bending bench at different faceplate velocities (100, 200, 400 and 800 μm/s) was used. For comparison, the same dynamic measurements were also carried out on non-aged fibers.After acid vapor condensation, salt crystal deposits on the fibers were displayed using an electron scanning microscope. These crystals became visible to the naked eye from the seventh day.     

Resonance and scattering in microstructured optical fibers

We present an investigation into the mechanism for guidance of microstructured optical fibers consisting of high-refractive-index cylinders embedded in a low-index background. A new guidance regime is identified in which the fibers' confinement losses depend strongly on wavelength and the positions of the loss minima and maxima depend on the scattering properties of individual cylinders and only weakly on their position and number. We point out similarities between these results and those reported recently for two-dimensional antiresonant reflecting waveguides.