高线性度Al_xGa_(1-x)N/Al_yGa_(1-y)N/GaN高电子迁移率晶体管优化设计

对新型复合沟道AlxGa1-xN/AlyGa1-yN/GaN高电子迁移率晶体管(HEMT)进行了优化设计.从半导体能带理论与量子阱理论出发,自洽求解了器件层结构参数对器件导带能级以及二维电子气(2DEG)中载流子浓度和横向电场的影响.用TCAD软件仿真得到了器件的层结构参数对器件性能的影响.结合理论分析和仿真结果确定了器件的最佳外延层结构Al0.31Ga0.69N/Al0.04Ga0.96N/GaNHEMT.对栅长1μm,栅宽100μm的器件仿真表明,器件的最大跨导为300mS/mm,且在栅极电压-2—1V的宽范围内跨导变化很小,表明器件具有较好的线性度;器件的最大电流密度为1300mA/mm,特征频率为11.5GHz,最大振荡频率为32.5GHz.     

Novel attributes of AlGaN/AlN/GaN/SiC HEMTs with the multiple indented channel

In this paper, a high performance AlGaN/AlN/GaN/SiC High Electron Mobility Transistor (HEMT) with the multiple indented channel (MIC-HEMT) is proposed. The main focus of the proposed structure is based on reduction of the space around the gate, stop of the spread of the depletion region around the source–drain, and decrement of the thickness of the channel between the gate and drain. Therefore, the breakdown voltage increases, meanwhile the elimination of the gate depletion layer extension to source/drain decreases the gate–source and gate–drain capacitances. The optimized results reveal that the breakdown voltage and the drain saturation current increase about 178% and 46% compared with a conventional HEMT (C-HEMT), respectively. Therefore, the maximum output power density is improved by factor 4.1 in comparison with conventional one. Also, the cut-off frequency of 25.2 GHz and the maximum oscillation frequency of 92.1 GHz for the MIC-HEMT are obtained compared to 13 GHz and 43 GHz for that of the C-HEMT and the minimum figure noise decreased consequently of reducing the gate–drain and gate–source capacitances by about 42% and 40%, respectively. The proposed MIC-HEMT shows a maximum stable gain (MSG) exceeding 24.1 dB at 3.1 GHz which the greatest gain is yet reported for HEMTs, showing the potential of this device for high power RF applications.     

Fang–Howard wave function modelling of electron mobility in AlInGaN/AlN/InGaN/GaN double heterostructures

To study the electron transport properties in InGaN channel-based heterostructures,a revised Fang-Howard wave function is proposed by combining the effect of GaN back barrier.Various scattering mechanisms,such as dislocation impurity(DIS) scattering,polar optical phonon(POP) scattering,piezoelectric field(PE) scattering,interface roughness(IFR) scattering,deformation potential(DP) scattering,alloy disorder(ADO) scattering from InGaN channel layer,and temperature-dependent energy bandgaps are considered in the calculation model.A contrast of AlInGaN/AlN/InGaN/GaN double heterostructure(DH) to the theoretical AlInGaN/AlN/InGaN single heterostructure(SH) is made and analyzed with a full range of barrier alloy composition.The effect of channel alloy composition on InGaN channel-based DH with technologically important Al(In,Ga)N barrier is estimated and optimal indium mole fraction is 0.04 for higher mobility in DH with Al_(0.4)In_(0.07)Ga_(0.53)N barrier.Finally,the temperature-dependent two-dimensional electron gas(2 DEG) density and mobility in InGaN channel-based DH with Al_(0.83)In_(0.13)Ga_(0.0)4 N and Al_(0.4)In_(0.07)Ga_(0.53)N barrier are investigated.Our results are expected to conduce to the practical application of InGaN channel-based heterostructures.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

Operational improvement of AlGaN/GaN HEMT on SiC substrate with the amended depletion region

In this paper, a high performance AlGaN/GaN High Electron Mobility Transistor (HEMT) on SiC substrates is presented to improve the electrical operation with the amended depletion region using a multiple recessed gate (MRG–HEMT). The basic idea is to change the gate depletion region and a better distribution of the electric field in the channel and improve the device breakdown voltage. The proposed gate consists of lower and upper gate to control the channel thickness. Also, the charge of the depletion region will change due to the optimized gate. In addition, a metal between the gate and drain including the horizontal and vertical parts is used to better control the thickness of the channel. The breakdown voltage, maximum output power density, cut-off frequency, maximum oscillation frequency, minimum noise figure, maximum available gain (MAG), and maximum stable gain (MSG) are some parameters for designers which are considered and are improved in this paper.     

Short-gate AlGaN/GaN high-electron mobility transistors with BGaN buffer

Using the semi-insulating property and small lattice constant a of wurtzite BGaN alloy, we propose a BGaN buffer with a B-content of 1% to enhance two-dimensional electron gas(2 DEG) confinement in a short-gate AlGaN/GaN highelectron mobility transistor(HEMT). Based on the two-dimensional TCAD simulation, the direct current(DC) and radio frequency(RF) characteristics of the AlGaN/GaN/B_(0.01)Ga_(0.99)N structure HEMTs are theoretically studied. Our results show that the BGaN buffer device achieves good pinch-off quality and improves RF performance compared with GaN buffer device. The BGaN buffer device can allow a good immunity to shift of threshold voltage for the aspect ratio(LG/d)down to 6, which is much lower than that the GaN buffer device with L_G/d=11 can reach. Furthermore, due to a similar manner of enhancing 2 DEG confinement, the B_(0.01)Ga_(0.99)N buffer device has similar DC and RF characteristics to those the AlGaN buffer device possesses, and its ability to control short-channel effects(SCEs) is comparable to that of an Al_(0.03)Ga_(0.97)N buffer. Therefore, this BGaN buffer with very small B-content promises to be a new method to suppress SCEs in GaN HEMTs.     

The physical process analysis of the capacitance-voltage characteristics of AlGaN/AlN/GaN high electron mobility transistors

This paper deduces the expression of the Schottky contact capacitance of AlGaN/AlN/GaN high electron mobility transistors (HEMTs), which will help to understand the electron depleting process. Some material parameters related with capacitance-voltage profiling are given in the expression. Detailed analysis of the forward-biased capacitance has been carried on. The gate capacitance of undoped AlGaN/AlN/GaN HEMT will fall under forward bias. If a rising profile is obviously observed, the donor-like impurity or trap is possibly introduced in the barrier.     

GaN缓冲层对直流反应磁控溅射AlN薄膜的影响(英文)

通过直流磁控反应溅射制备了氮化铝(AlN)薄膜,研究了沉积条件与氮化镓(GaN)缓冲层对薄膜质量的影响。利用X-射线衍射仪(XRD)和扫描电镜(SEM)表征了AlN薄膜的晶体结构和表面形貌。XRD研究结果表明,低工作压强、短靶距和适当的氮气偏压有利于(002)择优取向的AlN薄膜沉积。随着沉积时间的增加,沉积在50 nm厚的GaN缓冲层上的AlN薄膜的(002)面的衍射峰的半高宽急剧减小,而沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的衍射峰的半高宽几乎不变。SEM测试结果表明:在沉积的初期,沉积在1μm厚的GaN薄膜上的AlN薄膜的(002)面的晶粒大小分布比沉积在50 nm厚的GaN缓冲层上的AlN薄膜的均匀,而随着沉积时间的增加,它们的晶粒大小分布几乎趋向一致。     

Influence of Schottky drain contacts on the strained AlGaN barrier layer of AlGaN/AlN/GaN heterostructure field-effect transistors

Rectangular Schottky drain AlGaN/AlN/GaN heterostructure field-effect transistors (HFETs) with different gate contact areas and conventional AlGaN/AlN/GaN HFETs as control were both fabricated with same size. It was found there is a significant difference between Schottky drain AlGaN/AlN/GaN HFETs and the control group both in drain series resistance and in two-dimensional electron gas (2DEG) electron mobility in the gate-drain channel. We attribute this to the different influence of Ohmic drain contacts and Schottky drain contacts on the strained AlGaN barrier layer. For conventional AlGaN/AlN/GaN HFETs, annealing drain Ohmic contacts gives rise to a strain variation in the AlGaN barrier layer between the gate contacts and the drain contacts, and results in strong polarization Coulomb field scattering in this region. In Schottky drain AlGaN/AlN/GaN HFETs, the strain in the AlGaN barrier layer is distributed more regularly.     

Recessed-gate quasi-enhancement-mode AlGaN/GaN high electron mobility transistors with oxygen plasma treatment

In this paper,the enhancement-mode AlGaN/GaN HEMT combined with the low damage recessed-gate etching and the optimized oxygen plasma treatment was fabricated.Scanning electron microscope/energy dispersive spectrometer(SEM/EDS) method and x-ray photoelectron spectroscopy(XPS) method were used to confirm the formation of oxides.Based on the experimental results,the obtained enhancement-mode HEMT exhibited a threshold voltage of 0.5 V,a high peak transconductance of 210 mS/mm,and a maximum drain current of 610 mA/mm at the gate bias of 4 V.Meanwhile,the on/off current ratio of enhancement-mode HEMT was as high as 10~8,drain induced barrier lowering(DIBL) was as low as 5 raV/V,and subthreshold swing(SS) of 80 mV/decade was obtained.Compared with the conventional HEMT,the Schottky reverse current of enhancement-mode HEMT was three orders of magnitude lower,and the off-state breakdown voltage of which was higher.In addition,a power gain cutoff frequency(/max) of the enhancement-mode HEMT was larger than that of the conventional one.     

Influence of AlN interfacial layer on electrical properties of high-Al-content Al0.45Ga0.55N/GaN HEMT structure

Unintentionally doped high-Al-content Al_0.45Ga_0.55N/GaN high electron mobility transistor (HEMT) structures with and without AlN interfacial layer were grown by metal-organic chemical vapor deposition (MOCVD) on two-inch sapphire substrates. The effects of AlN interfacial layer on the electrical properties were investigated. At 300 K, high two-dimensional electron gas (2DEG) density of 1.66 × 10¹³ cm⁻² and high electron mobility of 1346 cm² V⁻¹ s⁻¹ were obtained for the high Al content HEMT structure with a 1 nm AlN interfacial layer, consistent with the low average sheet resistance of 287 Ω/sq. The comparison of HEMT wafers with and without AlN interfacial layer shows that high Al content AlGaN/AlN/GaN heterostructures are potential in improving the electrical properties of HEMT structures and the device performances.     

Investigation of AlInN HEMT structures with different AlGaN buffer layers grown on sapphire substrates by MOCVD

We investigate the structural and electrical properties of Al_xIn_1–xN/AlN/GaN heterostructures with AlGaN buffers grown by MOCVD, which can be used as an alternative to AlInN HEMT structures with GaN buffer. The effects of the GaN channel thickness and the addition of a content graded AlGaN layer to the structural and electrical characteristics were studied through variable temperature Hall effect measurements, high resolution XRD, and AFM measurements. Enhancement in electron mobility was observed in two of the suggested Al_xIn_1?xN/AlN/GaN/Al_0.04Ga_0.96N heterostructures when compared to the standard Al_xIn_1–xN/AlN/GaN heterostructure. This improvement was attributed to better electron confinement in the channel due to electric field arising from piezoelectric polarization charge at the Al_0.04Ga_0.96N/GaN heterointerface and by the conduction band discontinuity formed at the same interface. If the growth conditions and design parameters of the Al_xIn_1?xN HEMT structures with AlGaN buffers can be modified further, the electron spillover from the GaN channel can be significantly limited and even higher electron mobilities, which result in lower two-dimensional sheet resistances, would be possible.     

AlGaN/GaN-based HEMT on SiC substrate for microwave characteristics using different passivation layers

In this paper, a new gate-recessed AlGaN/GaN-based high electron mobility transistor (HEMT) on SiC substrate is proposed and its DC as well as microwave characteristics are discussed for Si₃N₄ and SiO₂ passivation layers using technology computer aided design (TCAD). The two-dimensional electron gas (2DEG) transport properties are discussed by solving Schr?dinger and Poisson equations self-consistently resulting in various subbands having electron eigenvalues. From DC characteristics, the saturation drain currents are measured to be 600?mA/mm and 550?mA/mm for Si₃N₄ and SiO₂ passivation layers respectively. Apart from DC, small-signal AC analysis has been done using two-port network for various microwave parameters. The extrinsic transconductance parameters are measured to be 131.7?mS/mm at a gate voltage of V _gs?= ?0.35?V and 114.6?mS/mm at a gate voltage of V _gs?= ?0.4?V for Si₃N₄ and SiO₂ passivation layers respectively. The current gain cut-off frequencies (f _t) are measured to be 27.1?GHz and 23.97?GHz in unit-gain-point method at a gate voltage of ?0.4?V for Si₃N₄ and SiO₂ passivation layers respectively. Similarly, the power gain cut-off frequencies (f _max) are measured to be 41?GHz and 38.5?GHz in unit-gain-point method at a gate voltage of ?0.1?V for Si₃N₄ and SiO₂ passivation layers respectively. Furthermore, the maximum frequency of oscillation or unit power gain (MUG = 1) cut-off frequencies for Si₃N₄ and SiO₂ passivation layers are measured to be 32?GHz and 28?GHz respectively from MUG curves and the unit current gain, ?O?h ₂₁??O?=?1 cut-off frequencies are measured to be 140?GHz and 75?GHz for Si₃N₄ and SiO₂ passivation layers respectively from the abs ?O?h ₂₁??O curves. HEMT with Si₃N₄ passivation layer gives better results than HEMT with SiO₂ passivation layer.     

The effect of a HfO2 insulator on the improvement of breakdown voltage in field-plated GaN-based HEMT

A GaN/Al_0.3Ga_0.7N/AlN/GaN high-electron mobility transistor utilizing a field plate (with a 0.3 μm overhang towards the drain and a 0.2 μm overhang towards the source) over a 165-nm sputtered HfO₂ insulator (HfO₂-FP-HEMT) is fabricated on a sapphire substrate. Compared with the conventional field-plated HEMT, which has the same geometric structure but uses a 60-nm SiN insulator beneath the field plate (SiN-FP-HEMT), the HfO₂-FP-HEMT exhibits a significant improvement of the breakdown voltage (up to 181 V) as well as a record field-plate efficiency (up to 276 V/μm). This is because the HfO₂ insulator can further improve the modulation of the field plate on the electric field distribution in the device channel, which is proved by the numerical simulation results. Based on the simulation results, a novel approach named the proportional design is proposed to predict the optimal dielectric thickness beneath the field plate. It can simplify the field-plated HEMT design significantly.     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

Device research on GaAs-based InAlAs/InGaAs metamorphic high electron mobility transistors grown by metal organic chemical vapour deposition

This paper applies a novel quad-layer resist and e-beam lithography technique to fabricate a GaAs-based InAlAs/InGaAs metamorphic high electron mobility transistor (HEMT) grown by metal organic chemical vapour deposition (MOCVD). The gate length of the metamorphic HEMT was 150~nm, the maximum current density was 330~mA/mm, the maximum transconductance was 470~mS/mm, the threshold voltage was -0.6~V, and the maximum current gain cut-off frequency and maximum oscillation frequency were 102~GHz and 450~GHz, respectively. This is the first report on tri-termination devices whose frequency value is above 400~GHz in China. The excellent frequency performances promise the possibility of metamorphic HEMTs grown by MOCVD for millimetre-wave applications, and more outstanding device performances would be obtained after optimizing the material structure, the elaborate T-gate and other device processes further.     

Neutron irradiation effects on A1GaN//GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors(HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10 15 cm 2.The dc characteristics of the devices,such as the drain saturation current and the maximum transconductance,decreased after neutron irradiation.The gate leakage currents increased obviously after neutron irradiation.However,the rf characteristics,such as the cut-off frequency and the maximum frequency,were hardly affected by neutron irradiation.The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism.It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas(2DEG) decreased after neutron irradiation.There was no evidence of the full-width at half-maximum of X-ray diffraction(XRD) rocking curve changing after irradiation,so the dislocation was not influenced by neutron irradiation.It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

Effects of GaN cap layer thickness on an AlN/GaN heterostructure

In this study, we investigate the effects of GaN cap layer thickness on the two-dimensional electron gas (2DEG) electron density and 2DEG electron mobility of AlN/GaN heterostructures by using the temperature-dependent Hall measurement and theoretical fitting method. The results of our analysis clearly indicate that the GaN cap layer thickness of an AlN/GaN heterostructure has influences on the 2DEG electron density and the electron mobility. For the AlN/GaN heterostructures with a 3-nm AlN barrier layer, the optimized thickness of the GaN cap layer is around 4 nm and the strained a-axis lattice constant of the AlN barrier layer is less than that of GaN.     

High linearity AlGaN/GaN HEMT with double-Vth coupling for millimeter-wave applications

We demonstrated an AlGaN/GaN high electron mobility transistor(HEMT)namely double-Vthcoupling HEMT(DVC-HEMT)fabricated by connecting different threshold voltage(Vth)values including the slant recess element and planar element in parallel along the gate width with N;O plasma treatment on the gate region.The comparative studies of DVC-HEMT and Fin-like HEMT fabricated on the same wafer show significantly improved linearity of transconductance(Gm)and radio frequency(RF)output signal characteristics in DVC-HEMT.The fabricated device shows the transconductance plateau larger than 7 V,which yields a flattened fT/fmax-gate bias dependence.At the operating frequency of 30 GHz,the peak power-added efficiency(PAE)of 41%accompanied by the power density(Pout)of 5.3 W/mm.Furthermore,the proposed architecture also features an exceptional linearity performance with 1-d B compression point(P1 d B)of 28 d Bm,whereas that of the Fin-like HEMT is 25.2 d Bm.The device demonstrated in this article has great potential to be a new paradigm for millimeter-wave application where high linearity is essential.