Yb∶Y_2O_3陶瓷薄片激光器获得10.5 W连续激光输出

室温下采用中心波长约970 nm准直输出的大功率激光二极管模块作为抽运源,端面抽运双程吸收的腔型结构,抽运原子数分数为8%的Yb:Y2O3多晶透明陶瓷片获得连续激光输出。抽运阈值功率为7 W,当抽运功率达到35 W时,获得优化连续激光输出功率为10.5 W,光光转换效率为30%,斜率效率为37.5%。激光输出功率随抽运功率基本呈线性增长。采用更高功率抽运源、优化谐振腔结构和减小热效应的影响,Yb∶Y2O3陶瓷激光器的输出功率和效率将会得到进一步提高。     

Fiber fuse behavior in k W-level continuous-wave double-clad field laser

In this study, original experimental data for fiber fuse in k W-level continuous-wave(CW) high power double-clad fiber(DCF) laser are reported. The propagating velocity of the fuse is 9.68 m/s in a 3.1-k W Yb-doped DCF laser. Three other cases in Yb-doped DCF are also observed. We think that the ignition of fiber fuse is caused by thermal mechanism,and the formation of bullet-shaped tracks is attributed to the optical discharge and temperature gradient. The inducements of initial fuse and formation of bullet-shaped voids are analyzed. This investigation of fiber fuse helps better understand the fiber fuse behavior, in order to avoid the catastrophic destruction caused by fiber fuse in high power fiber laser.     

Yb3+:Y2O3透明陶瓷激光器获得5 W连续激光输出

用带尾纤输出的激光二极管作为抽运源,采用端面抽运10％Yb^3 ：Y2O3多晶透明陶瓷的方式获得了连续激光输出。抽运阈值功率为5．6W,当陶瓷介质吸收的抽运功率为31．11W时,Yb^3 ：Y2O3多晶透明陶瓷获得了最大连续激光输出功率5．48W。光—光转换效率为17．6％,斜率效率为25％。同时在激光实验过程中,没有发现饱和现象,因此采用更高功率的激光二极管作为抽运源,陶瓷的激光输出功率会得到进一步提高。这一研究成果表明,多晶透明陶瓷是一种非常有潜力的激光增益介质。     

NdKYW新型全固体激光器研究

报道了采用半导体二极管抽运的掺钕钨酸钇钾［Nd3+KY(WO4)2］(简称NdKYW)蓝绿光激光器。腔内倍频采用了Ⅰ类临界相位匹配LBO(LiB3O5)晶体作为倍频器,阈值抽运功率为400 mW,在抽运功率为2 W时获得了200 mW的530 nm连续激光输出,其倍频光的光-光转换效率为10%。     

Diode-pumped laser performance of Tm:Sc_2SiO_5 crystal at 1971 nm

The 4-at.% Tm:Sc_2SiO_5 (Tm:SSO) crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave(CW) laser output of(100)-cut Tm:SSO with the dimensions of 3 mm×3 mm×3 mm under laser diode(LD)-pumping is realized. The full width at half maximum(FWHM) of the laser emitting reaches up to 21 nm. The laser threshold of Tm:SSO is measured to be 0.43 W. Efficient diode-pumped CW laser performance of Tm:SSO is demonstrated with a slope efficiency of 25.9% and maximum output power of 934 mW.     

基于多层石墨烯可饱和吸收体的被动调Q Ho∶YAG激光器

报道了2μm被动调Q的Ho∶YAG激光器,该激光器采用Tm~(3+)光纤激光器作为泵浦源,使用多层石墨烯作为可饱和吸收体。在连续波激光输出模式下,当泵浦功率为4.2 W时,获得了750 mW激光输出,输出激光中心波长为2.09μm,斜率效率为29.6%。在连续波激光器谐振腔中插入多层石墨烯可饱和吸收体并调整谐振腔,获得了脉冲激光输出。当泵浦功率为4.2 W时,获得最小脉冲宽度3.1μs、重复频率66.6 kHz的脉冲激光输出,其最大平均输出功率为170 mW,斜率效率为12.6%,光束质量因子M_x~2=1.15,M_y~2=1.12。     

Random distributed feedback fiber laser pumped by an ytterbium doped fiber laser

A random distributed feedback fiber laser operating at 1115 nm has been demonstrated experimentally in standard communication optical fibers by using a LD-pumped Yb-doped fiber laser as the pump source. We have studied the effect of different fiber spans on this new type of random fiber laser output power. It is shown that the generation power is the highest up to 198 mW in a 50 km fiber span. The slope efficiency is more than 28.7%. Stable, high-power continuous-wave (CW) lasing can be generated when the pump power is 3.6 W. The threshold power has also been calculated which well proves a random fiber laser operating via Rayleigh scattering, amplified through the Raman scattering.     

Growth and properties of KLu(WO4)2, and novel ytterbium and thulium lasers based on this monoclinic crystalline host

High‐quality crystals of monoclinic KLu(WO₄)₂, shortly KLuW, were grown with sizes sufficient for its characterization and substantial progress was achieved in the field of spectroscopy and laser operation with Yb³⁺‐ and Tm³⁺‐doping. We review the growth methodology for bulk KLuW and epitaxial layers, its structural, thermo‐mechanical, and optical properties, the Yb³⁺ and Tm³⁺ spectroscopy, and present laser results obtained in several operational regimes both with Ti:sapphire and direct diode laser pumping using InGaAs and AlGaAs diodes near 980 and 800 nm, respectively. The slope efficiencies with respect to the absorbed pump power achieved with continuous‐wave (CW) bulk and epitaxial Yb:KLuW lasers under Ti:sapphire laser pumping were ≈ 57 and ≈ 66%, respectively. Output powers as high as 3.28 W were obtained with diode pumping in a simple two‐mirror cavity where the slope efficiency with respect to the incident pump power reached ≈ 78%. Passively Q‐switched laser operation of bulk Yb:KLuW was realized with a Cr:YAG saturable absorber resulting in oscillation at ≈ 1031 nm with a repetition rate of 28 kHz and simultaneous Raman conversion to ≈ 1138 nm with maximum energies of 32.4 and 14.4 μJ, respectively. The corresponding pulse durations were 1.41 and 0.71 ns. Passive mode‐locking by a semiconductor saturable absorber mirror (SESAM) produced bandwidth‐limited pulses with duration of 81 fs (1046 nm, 95 MHz) and 114 fs (1030 nm, 101 MHz) for bulk and epitaxial Yb:KLuW lasers, respectively. Slope efficiency as high as 69% with respect to the absorbed power and an output power of 4 W at 1950 nm were achieved with a diode‐pumped Tm:KLuW laser. The slope efficiency reached with an epitaxial Tm:KLuW laser under Ti:sapphire laser pumping was 64 %. The tunability achieved with bulk and epitaxial Tm:KLuW lasers extended from 1800 to 1987 nm and from 1894 to 2039 nm, respectively.     

连续锁模Nd∶YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd∶YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 WLD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值(35 mW)和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W 时获得了210 mW的平均输出功率.     

Laser capabilities of CuBr mixture excited by RF discharge

Our investigations demonstrated that utilizing copper bromide (CuBr) mixture as a source of Cu atoms in a RF-excited discharge can be a promising alternative to the Cu sputtered system, when the development of Cu ion gas laser is considered. Both spectroscopic and laser investigations showed that the threshold input power for lasing was reduced about 5 times using the CuBr-based system instead of the Cu-sputtered system. Pulsed and CW laser oscillation on Cu⁺ transitions in the near IR spectral region was obtained in RF-excited He-CuBr discharge operated at 13.56 MHz and 27.12 MHz. At input RF power of 800 W, a laser output power of 10 mW at the 780.8 nm Cu ion laser line was achieved. An increase of laser output power by a factor of two, as well as better Cu vapour axial distribution and better discharge stability, was attained when DC discharge was superimposed on the RF discharge. Laser gain on 11 UV Cu ion lines was observed in RF-excited Ne-CuBr discharge. basing on the obtained results, we consider the CuBr laser system excited by RF discharge capable of generating UV laser radiation at relatively low input power. Received 4 January 1999     

连续锁模Nd：YVO4激光器实现1 GHz高频输出

LD抽运全固体Nd:YVO4激光器在连续锁模状态运转下获得了高达1 GHz的重复频率.实验中采用半导体可饱和吸收镜作为锁模元件.利用透过率只有0.8%的输出镜以及可获得较小抽运光斑的2 W LD作为抽运源来优化激光器设计,有效地抑制了调Q锁模状态的运转.低的激光器振荡阈值（35 mW）和连续锁模阈值(0.8 W)显示了饱和吸收体低的插入损耗和激光器合理的设计.在最大抽运1.6 W时获得了210 mW的平均输出功率.     

High power CW and Q-switched operation of a diode-side-pumped Nd: YAG 1319-nm laser

We demonstrated the highly efficient continuous wave(CW)and Q-switched infrared laser from a diodeside-pumped Nd:YAG crystal.A CW output as high as 66 W at 1319 nm was achieved under the pump power of 460 W,corresponding to a coversion efficiency of 14.3%.A maximum average power of 8.9 W of TEM00 mode was obtained in Q-switched operation at the repetition rate of 8 kHz.The performance of the laser considering the thermal lens effect induced by pump power Was also analyzed.     

Efficient and compact intracavity-frequency-doubled YVO4/Nd:YVO4/KTP laser through analysis of the interaction length

In this paper, a stable end-pumped intracavity-frequency-doubled green laser was demonstrated. The interaction length of different pump systems before setting up the experiment was analyzed in order to find out an effective pump system. The experimental results indicate that the pump system in our configuration is beneficial to the efficient CW Nd lasers. A continue-grown composite crystal YVO₄/Nd:YVO₄, with Nd³⁺ concentration doping of 0.3 at.%, is used as laser medium. With an incident pump power of 27.5 W, as high as 7.2 W of CW output power at 532 nm was achieved. The optical-to-optical conversion efficiency of 26.2% was obtained in CW modes with a flat-flat cavity design.     

Broad gain,continuous-wave operation of InP-based quantum cascade laser at λ~11.8 μm

We demonstrate a broad gain, continuous-wave (CW) operation InP-based quantum cascade laser (QCL) emitting at 11.8 μm with a modified dual-upper-state (DAU) and diagonal transition active region design. A 3 mm cavity length, 16.5 μm average ridge wide QCL with high-reflection (HR) coatings demonstrates a maximum peak power of 1.07 W at 283 K and CW output power of 60 mW at 293 K. The device also shows a broad and dual-frequency lasing spectrum in pulsed mode and a maximum average power of 258.6 mW at 283 K. Moreover, the full width at half maximum (FWHM) of the electroluminescent spectrum measured at subthreshold current is 2.37 μm, which indicates a broad gain spectrum of the materials. The tuning range of 1.38 μm is obtained by a grating-coupled external cavity (EC) Littrow configuration, which is beneficial for gas detection.     

Efficient and high-power intracavity frequency doubled diode-side-pumped Nd:YAG/KTP continuous wave (CW) green laser

Highly efficient continuous wave (CW) green beam generation by intracavity frequency doubling of a diode side-pumped Nd:YAG laser using a single pump head based on a copper-coated flow tube in a V-shaped cavity geometry has been demonstrated. A maximum 30.5 W of CW green power was obtained at a total diode pumping power of 260 W corresponding to 11.7% conversion efficiency of diode pump power to CW green power and 4.7% conversion efficiency of electrical power to CW green power. The performance of the laser by considering the pump power induced thermal lensing effect and the M²-parameter at the fundamental wavelength has been analyzed.     

Low noise, continuous-wave single-frequency 1.5-μm laser generated by a singly resonant optical parametric oscillator

We report a low noise continuous-wave (CW) single-frequency 1.5-μm laser source obtained by a singly resonant optical parametric oscillator (SRO) based on periodically poled lithium niobate (PPLN). The SRO was pumped by a CW single-frequency Nd:YVO₄ laser at 1.06 μm. The 1.02 W of CW single-frequency signal laser at 1.5 μm was obtained at pump power of 6 W. At the output power of around 0.75 W, the power stability was better than ±1.5% and no mode-hopping was observed in 30 min and frequency stability was better than 8.5 MHz in 1 min. The signal wavelength could be tuned from 1.57 to 1.59 μm by varying the PPLN temperature. The 1.5-μm laser exhibits low noise characteristics, the intensity noise of the laser reaches the shot noise limit (SNL) at an analysis frequency of 4 MHz and the phase noise is less than 1 dB above the SNL at analysis frequencies above 10 MHz.     

Two-pass amplification of CW laser by Nd/Cr:YAG ceramic Active mirror under lamp light pumping

The concept of an Active mirror with transparent Nd/Cr:YAG ceramics is proposed. A new ceramic material pumped by an arc-metal-halide lamp has been experimentally implemented. CW-laser light generated in a 1064 nm Nd:YAG micro-tip oscillator was amplified by an Active mirror made of Nd/Cr:YAG ceramic and pumped by CW arc-lamp light. The saturation power density of the Nd/Cr:YAG ceramic was lower than that of Nd:YAG because the stimulated-cross-section and lifetime were effectively enhanced by the sensitization of Cr ions. The maximum output laser power while keeping spatial beam quality was up to 3 W with an input lamp power of 9 W; the resulting optical-optical conversion efficiency of 33% was close to the theoretical prediction of nearly 50%.     

Highly efficient optically pumped cesium vapor laser

We have demonstrated an optically pumped continuous wave Cs vapor laser with an input power to output power slope efficiency of 81%. The laser power was 0.35 W for an input power of 0.57 W, yielding an overall optical efficiency of 63%.     

侧面泵浦主振荡功率放大器中的光束质量提高

报道了一种利用球差补偿效应提高侧面泵浦主振荡功率放大器输出光束质量的实验装置。在理论上提出了一种新的球差补偿方法,利用正球差经过会聚透镜焦点后向负球差转化的现象,补偿下一放大级中的正球差效应。在实验上搭建了两级放大的侧面泵浦Nd:YAG主振荡功率放大器。在连续输出的情况下,从振荡级输出功率为42W、光束质量因子为1.48的种子光,经过一级放大后的功率为74W,光束质量因子恶化为1.80;继续经过二级放大后,光束质量因子提高为1.40。实验结果表明,所提出的球差补偿理论是提高激光放大过程中光束质量的有效手段。     

555 nm laser sources based on intracavity frequency doubling of Nd:YGG laser

We report for the first time a yellow-green laser at 555 nm generation by intracavity frequency doubling of a continuous wave (CW) laser operation of a 1110 nm Nd-doped yttrium gallium garnet (Nd:YGG) laser under in-band diode pumping at 808 nm. An LBO crystal, cut for critical type I phase matching is used for second harmonic generation of the laser. At an incident pump power of 18.5 W, as high as 2.31 W of CW output power at 555 nm is achieved. The optical-to-optical conversion efficiency is up to 12.4%, and the fluctuation of the yellow-green output power was better than 2.8% in the given 4 h.