溴甲酚绿分光光度法测定牛血清白蛋白

在pH 3.3的Britton-Robinson (B-R)缓冲溶液中, 对溴甲酚绿(BCG)与牛血清白蛋白(BSA)相互作用的吸收光谱进行了初步研究. 结果表明: BCG与BSA作用在室温下能迅速结合成复合物, 并且随着BSA的浓度增大, 在444 nm处的吸收峰降低, 618 nm处吸收峰升高并红移至628 nm. 在此波长下测定其复合物的吸光度, 其吸光度的增加值(ΔA)与BSA的质量浓度在8～260 μg/mL范围内呈良好的线性关系(r=0.9996), 检出限为4 μg/mL. 该方法应用于鲜奶粉和液态纯牛奶样品中总蛋白的测定, 回收率分别为92.7%, 95.5%, 结果与考马斯亮蓝G250法基本一致.     

溴甲酚绿与甲砜霉素的显色反应及应用

在pH 4.0～5.3的条件下,甲砜霉素与溴甲酚绿反应生成具有1个正吸收峰和2个几乎相等的负吸收峰的离子缔合物。最大正吸收波长位于610 nm,2个负吸收波长分别位于652 nm和574 nm,表观摩尔吸光系数分别为2.16×104 L.mol-1.cm-1(正吸收),1.36×104 L.mol-1.cm-1(652 nm负吸收)和1.32×104 L.mol-1.cm-1(574 nm负吸收),线性范围均为0～5.3 mg/L。甲砜霉素在一定浓度范围内遵从朗伯比尔定律,由此建立了测定甲砜霉素的正吸收、负吸收及双波长叠加吸收光谱法。方法已用于人体尿液、血液及市售药物中甲砜霉素含量的测定。     

Spectrophotometric determination of chlorhexidine with bromocresol green by flow-injection and manual methods

A spectrophotometric study of the chlorhexidine/bromocresol green/Triton X-100 system is reported; at pH 5.3, both 2:1 and 1:1 bromocresol green/chlorhexidine complexes are formed. In the manual spectrophotometric method, Beer's law is obeyed for chlorhexidine concentrations of 2.9–32.2 μg ml^?1 (r.s.d. 0.4–1.3%); the molar absorptivity is 12 500 l mol^?1 cm^?1. In the flow-injection method, the calibration graph is linear for the chlorhexidine range 23.0–83.9 μg ml^?1 (r.s.d. 0.8%); the injection is ca. 60 h^?1. Benzocaine, acetylsalicylic acid, ascorbic acid and sucrose are tolerated at 10^?2?10^?3 M levels. Hibitane 5% was analyzed successfully.     

Extraction-spectrophotometric determination of amprolium hydrochloride using bromocresol green, bromophenol blue and bromothymol blue

A new procedure for the determination of amprolium hydrochloride by reaction with bromocresol green (BCG), bromophenol blue (BPB) and bromothymol blue (BTB) has been developed. The method consists of extracting the yellow ion-pair formed into chloroform from aqueous medium. The ion-pairs have absorption maxima at 420, 410 and 415 nm with molar absorptivities of 3.64 × 10⁴, 3.12 × 10⁴ and 2.31 × 10⁴1 mol^–1 cm^–1 for BCG, BPB and BTB, respectively. The method obeys Beer's law over the concentration ranges 0.6–12.0, 0.12–8.8 and 1.2–11.3 ag/ml amprolium hydrochloride for BCG, BPB and BTB, respectively. The method is simple, precise (relative standard deviation 0.665–2.210%), accurate (recovery 97.8–100.8%) and easily applied for pharmaceutical quality assurance for amprolium hydrochloride in raw materials and in formulated veterinary soluble powder.     

纳米Fe/TiO_2粉体的制备及其光催化性能

光催化法是近年来发展较快的一种环境治理技术,掺杂型TiO_2催化剂是当前研究的焦点之一.以四氯化钛为主要原料,利用简单的溶胶法制备了纳米TiO_2、Fe/TiO_2粉体,研究发现掺杂铁,能够有效地延缓锐钛矿型TiO_2向金红石型TiO_2的转变,提高Fe/TiO_2粉体的光催化活性,并且500℃焙烧后的Fe/TiO_2催化剂,在紫外光下催化活性较好.     

溴甲酚绿为内标-甲醛肟光度法测定水体中锰的研究

提出采用溴甲酚绿为内标 甲醛肟光度法测定水体中的锰。锰与甲醛肟络合物和内标物的最大吸收波长分别为450nm和612nm,校正后A450/A612值与Mn含量之间呈良好的线性关系,相关系数为0.9994。对于高度污染的工业废水,可取显色溶液进行任意稀释测定。应用本方法对含锰9.56mg/L的冶炼废水进行了测定,其标准偏差和相对标准偏差分别为0.12mg/L和1.3%,回收率为99.6%～101.2%。     

Spectrophotometric determination of trazodone, amineptine and amitriptyline hydrochlorides through ion-pair formation using methyl orange and bromocresol green reagents

A simple and rapid extraction spectrophotometric procedure has been developed for the determination of tricyclic anti-depressant drugs such as trazodone (TZH), amineptine (APH) and amitriptyline (ATPH) hydrochlorides in pure form and in different dosage forms. The method involves the formation of intense yellow ion-pairs between these drugs under investigation and methyl orange (MO) and bromocresol green (BCG) reagents followed by their extraction with 1,2-dichloroethane and quantitative microdetermination at 420 and 410 nm using MO or BCG, respectively. The optimum experimental conditions for the ion-pairs formation are established. The method permits the determination of TZH, APH and ATPH over a concentration range of 2-50, 2-50 and 1-25 microg ml(-1) for TZH, APH and ATPH, using MO and 1-25 microg ml(-1) for TZH, APH and ATPH, using BCG, respectively. The Sandell sensitivity (S) is found to be 0.106, 0.1071 and 0.0907 g cm(-2) for TZH, APH and ATPH, respectively, using MO reagent and 0.0788, 0.0661 and 0.0494 g cm(-2) for TZH, APH and ATPH, respectively, using BCG. The method is applicable for the assay of the investigated drugs in different dosage forms and the results are in good agreement with those obtained by the official method.     

Electrochemical Determination of Reduced Glutathione at Multiwalled Carbon Nanotubes/Poly(bromocresol green)Modified Glassy Carbon Electrode

A multiwalled carbon nanotubes/poly(bromocresol green) modfied glassy carbon electrode (MWNTs-PBG/GCE) was used to investigate the electrochemical behavior of reduced glutathione(GSH). GSH showed an irreversible oxidation process on MWNTs-PBG/GCE with an oxidation peak at 0.77 V(vs. SCE) in a phosphate buffer solution(pH=4.0). The kinetic parameters of the electrochemical behavior of GSH on MWNTs-PBG/GCE were calculated. Under the optimal conditions and with the help of amperometric method, a linear relationship was obtained between the oxidation peak current and GSH concentration in the range from 2×10–7 mol/L to 5×10–6 mol/L with the detection limit as 1×10–8 mol/L(signal-to-noise ratio of 3). The current reached the steady-state current within about 5 s. The modified electrode surface had very good reproducibility and stability.     

Equilibrium constant of the gamma-sultone and extraction constant of sodium and potassium ions from water into benzene in presence of 18-crown-6 and bromocresol green

An extraction procedure for the spectrophotometric determination of sodium or potassium involving a 1:1:1 metal ion: crown ether: sulfonephthalein dye monoanion ion associate has been described in the literature. In a recent paper from this laboratory the total dye content of the organic phase resulting from partitioning bromocresol green (HBCG) alone between water and benzene was determined from back extraction into an aqueous phosphate buffer. In benzene, bromocresol green is present to a large extent as a colorless lactone form, or gamma-sultone. The sultone equilibrium constant, K(dist) (sultone)=[sultone](o)/[BCG(-)](w)gamma(BCG(-))(w)a(H(+)) was found to be 373+/-42 mol(-1) dm(3). In the present study, sodium was extracted from water into benzene with 18-crown-6 and BCG(-), yielding K(dist) (sultone)=232 mol(-1) dm(3) and the conventional extraction constant, K(ex), of (5.49+/-0.49)x10(3) mol(-2) dm(6). Corresponding values from potassium extraction data are 256 mol(-1) dm(3) and (4.80+/-0.51)x10(6) mol(-2) dm(6), respectively. In the absence of ethanol, the calibration plot of sodium closely followed Beer's law, but that of potassium curved downward, approaching linearity in 15% ethanol. High 18-crown-6, low bromocresol green concentrations are analytically favorable for the extraction of potassium from the 15% aqueous ethanol mixture. All plots from the back-extractions (a measure of the total dye content in the benzene phase) were linear. Ethanol markedly reduced the reagent blank, when C(MCl)=0, as a result of the sultone being partitioned less favorably into benzene.     

Determination of the acid dissociation constant of bromocresol green and cresol red in water/AOT/isooctane reverse micelles by multiple linear regression and extended principal component analysis

The pKa of 3',3",5',5"tetrabromo-m-cresolsulfonephtalein (Bromocresol Green) and o-cresolsulphonephtalein (Cresol Red) was spectrophotometrically measured in a water/AOT/isooctane microemulsion in the presence of a series of buffers carrying different charges at different water/surfactant ratios. Extended Principal Component Analysis was used for a precise determination of the apparent pKa and of the spectra of the acid and base forms of the dye. The apparent pKa of dyes in water-in-oil microemulsions depends on the charge of the acid and base forms of the buffers present in the water pool. Combination with multiple linear regression increases the precision. Results are discussed taking into account the profile of the electrostatic potential in the water pool and the possible partition of the indicator between the aqueous core and the surfactant. The pKa corrected for these effects are independent of w0 and are close to the value of the pKa in bulk water. On the basis of a tentative hypothesis it is possible to calculate the true pKa of the buffer in the pool.     

Study on bromocresol green-cetyltrimethylammonium-deoxyribonucleic acids system by resonance light scattering spectrum methods

An assay of deoxyribonucleic acids (DNA) determination, with the sensitivity at nanogram level, was established in the present study by using a common spectrofluorometer to detect the intensity of resonance light scattering (RLS). In hexamethylene tetramine (HMTA) buffer (pH 11.00), Bromocresol Green (BCG) and deoxyribonucleic acids (DNA) react with cetyltrimethylammonium bromide (CTMAB) to form large particles of three-component complex, which results in strong enhanced RLS signals characterized by three peaks at 336, 390, and 622 nm and at 336 nm that is the strongest of the three enhanced RLS peaks. Mechanistic studies showed that the enhanced RLS stems from the aggregation of BCG on DNA through the bridged and synergistic effect of CTMAB. Yeast DNA (yDNA), in the range of 0.05-0.90 ngml(-1), fish sperm DNA (fsDNA) in the range of 0.05-0.80 ngml(-1), and calf thymus DNA (ctDNA) in the range of 0.05-0.80 ngml(-1) can be determined if 2.0 x 10(-6) moll(-1) BCG was employed. The determination limit of yDNA was 12.7 ngml(-1). Three synthetic samples of yDNA were analyzed with good reproducibility.     

Reversible pH-sensitive element based on bromocresol purple immobilized into the polymethacrylate matrix

Reversible pH-sensitive element based on bromocresol purple immobilized into the polymethacrylate matrix was developed. Applications of the pH-sensitive element for continuous monitoring pH of aqueous solution were demonstrated.     

Screening thermotolerant white-rot fungi for decolorization of wastewaters

To select a thermotolerant fungal strain for decolorization of wastewaters, ligninolytic enzyme production (lignin peroxidase, manganese peroxidase [MnP], and laccase), decolorization, and removal of total phenol and chemical oxygen demand (COD) were detected. Thirty-eight fungal strains were studied for enzyme production at 35 and 43°C on modified Kirk agar medium including 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) and MnCl₂. Thirteen strains grew on manganese-containing agar and provided green color on ABTS-containing agar plates under culture at 43°C. Decolorization of wastewater from alcohol distillery (WAD) by these strains was compared under static culture at 43°C, and Pycnoporus coccineus FPF 97091303 showed the highest potential. Thereafter, immobilized mycelia were compared with free mycelia for WAD decolorization under culture conditions of 43°C and 100 rpm. The immobilized mycelia on polyurethane foam enhanced the ligninolytic enzyme production as well as total phenol and color removal. At about the same COD removal, MnP and laccase produced by immobilized mycelia were 2 and 19 times higher than by free mycelia; the simultaneous total phenol and color removal were 3.1 and 1.5 times higher than the latter. Moreover, decolorization of synthesis dye wastewater was carried out at 43°C and 100 rpm. More than 80% of 300 mg/L of reactive blue-5 was decolorized by the immobilized mycelia within 1 to 2 d for four cycles.     

Substituent effects on thermal decolorization rates of bisbenzospiropyrans

[reaction: see text] A novel application of photochromic molecules is to mimic physiological oscillatory calcium signals by reversibly binding and releasing calcium ions in response to light. Substituent changes on the largely unexplored photochromic bisbenzospiropyran scaffold led to significant changes in thermal fading rates in several organic solvents. Excellent correlations have been found between fading rates and empirical Hammett constants as well as calculated ground-state energies. These correlations can be used to improve scaffold design.     

活性炭对乙二醛溶液的脱色研究

乙二醛是一种重要的化工产品和医药中间体,在纺织印染、建材、皮革、医药、农药、国防、涂料、轻工、粘合剂、石油、冶金、环保等方面具有广泛的用途[1,2]。其工业生产方法主要有乙醛硝酸氧化法和乙醇气相氧化法[3~6]。两种方法制得的乙二醛溶液在纯化过程中,溶液颜色加深,不能