Preparation of a well-defined amino-terminated self-assembled monolayer and copper microlines on a polyimide substrate covered with an oxide nanoskin

A well-ordered, uniform amino (NH(2))-terminated organosilane self-assembled monolayer (SAM) was prepared on a polyimide (PI) substrate, the surface of which had silica-like reactivity. First, through chemical vapor deposition of 1,3,5,7-tetramethylcyclotetrasiloxane and subsequent photooxidation using 172 nm vacuum ultraviolet light, an extremely thin silicon dioxide (SiO(2)) layer about 1 nm thick, which we call an "oxide nanoskin" (ONS), was prepared on a PI substrate. Due to the presence of this ONS layer, the PI surface's properties became almost identical with those of Si covered with native oxide (SiO(2)/Si) without any marked change in surface morphology, as evidenced by zeta-potential measurements, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). Next, this ONS-covered PI (ONS/PI) surface was exposed to vapor of a 12.5 vol % solution of N-(6-aminohexyl)(3-aminopropyl)trimethoxysilane (AHAPS) molecules diluted with absolute toluene. On the basis of contact angle analysis, the surface energy of this AHAPS/ONS/PI sample was mostly consistent with that of a SiO(2)/Si substrate covered with an AHAPS-SAM (AHAPS/SiO(2)/Si). On the other hand, the surface energy of an AHAPS-treated PI (AHAPS/PI) substrate was much smaller than that of the AHAPS/ONS/PI substrate due to insufficient surface coverage by the AHAPS molecules. This was also confirmed by lateral force microscopy using photolithographically micropatterned samples. Fabricated micropatterns composed of AHAPS- and SiO(2)-covered regions were clearly imaged on the AHAPS/ONS/PI substrate through their difference in friction, while the friction contrast of the micropatterned AHAPS/PI substrate was unclear. This marked difference in packing density of the AHAPS molecules had a direct influence on the adsorption behavior of palladium colloids and subsequent electroless plating of copper (Cu). As confirmed by AFM and XPS, metallization proceeded only on the AHAPS-covered regions, while the SiO(2)-covered regions remained free of deposits, resulting in the formation of 10-mum-wide Cu microlines on both samples. However, the plating rate achieved on the AHAPS/ONS/PI substrate was about 4.5 times faster than that on the AHAPS/PI substrate and the pattern resolution was considerably fine.     

三甲基氯硅烷对纳米多孔二氧化硅薄膜的修饰

以正硅酸乙酯为先驱体,采用溶胶-凝胶法,结合旋转涂胶、超临界干燥工艺在硅片上制备了纳米多孔SiO2薄膜.用三甲基氯硅烷(TMCS)对该SiO2薄膜进行了表面修饰,采用FTIR、TG-DTA、AFM和椭偏仪等方法研究了TMCS修饰前后薄膜的结构、形貌、厚度与介电常数等性能.超临界干燥后的SiO2薄膜含有Si－O－Si与Si－OR结构,呈疏水性.在空气中250 ℃以上热处理后SiO2薄膜因含有Si－OH而呈吸水性. TMCS修饰后的SiO2薄膜在温度不高于450 ℃时可保持其疏水性和多孔结构. SiO2薄膜经TMCS修饰后基本粒子和孔隙尺寸增大,孔隙率提高,介电常数可降低至2.5以下.     

Lack of association between a cationic protein and a cationic fluorosurfactant

Surface tension, 19F and 1H NMR spectroscopy, and cryotransmission electron microscopy are used to characterize the state of association in aqueous solutions of a fluorosurfactant CF3(CF2)nSO2NH(CH2)3-4N(CH3)3+ I- (n = 8, 6) with and without lysozyme added. In the absence of lysozyme, we find monomers, small aggregates, and large vesicles to coexist, with the individual fluorosurfactant molecules exchanging slowly (>1 ms) among those states. When both lysozyme and fluorosurfactant are present in the solution, they have no measurable influence on the physical state of the other. In contrast, a hydrogenated cationic surfactant with the same headgroup, hexadecyltrimethylammonium bromide, is shown to associate to lysozyme.     

Modifying the surface of Fe3O4/SiO2 magnetic nanoparticles with C18/NH2 mixed group to get an efficient sorbent for anionic organic pollutants

In this article, C(18)/NH(2) mixed group modified Fe(3)O(4)/SiO(2) magnetic nanoparticles (Fe(3)O(4)/SiO(2)/C(18)+NH(2) MNPs) were successfully synthesized and used for the extraction of perfluorinated compounds (PFCs) from large volume of water solution. The Fe(3)O(4)/SiO(2)/C(18)+NH(2) MNPs, about 25 nm in diameter, possess high extraction ability to the anionic organic pollutants due to the dual function of hydrophobic octadecyl group and cationic aminopropyl groups at low pH. More than 90% of the targets can be extracted from 500 mL of water solution with 0.1g of the MNP sorbent at pH 3. Twenty min is sufficient to reach adsorption equilibrium, and the targets can be desorbed from the sorbent readily with 12 mL of alkalized methanol after magnetic separation. Simplified extraction procedure could be achieved because of the superparamagnetism and high saturation magnetization of the sorbent (44 emu g(-1)). Therefore, preconcentration of trace level of PFCs from water solution can be performed by using this Fe(3)O(4)/SiO(2)/C(18)+NH(2) MNP sorbent which are stable for multiple reuses.     

Nonlithographic micro- and nanopatterning of TiO2 using polymer stamped molecular templates

The polymer-on-polymer stamping technique was used to template patterned TiO2 onto polymer thin films. Polystyrene-b-polyvinyl pyridine diblock copolymer (PS-b-PVP) was stamped on a layer-by-layer assembled thin film of poly(allylamine hydrochloride) and poly(acrylic acid). After rinsing the surface with a good solvent for the block copolymer, an adsorbed PS-b-PVP monolayer remained on the polyelectrolyte film, resulting in a pattern of alternating hydrophobic and carboxylic acid containing hydrophilic regions. The surface was used as a template for the selective deposition of TiO2 on the multilayer surface, using an acid-catalyzed hydrolysis of(NH4)2TiF6. Using this novel approach, we have successfully demonstrated the patterning of TiO2 film on a polyelectrolyte multilayer. Finally, nanoscale features consisting of 200 nm lines alternating with a 350 nm period was accomplished. This paper represents the first such attempt to create an all-polymer nonlithographic template for the directed deposition of TiO2 or related metal oxides; this technique, which utilizes the versatile polyelectrolyte multilayer process, enables the construction of complex polymer-inorganic microstructures suitable for electrooptical and photonic applications.     

Identification of mobile species in cationic polymer lubricant layer on silicon oxide from AFM and XPS analyses

The nanoscale spreading of a cationic polymer lubricant (CPL) film consisting of polydimethylsiloxane with quaternary ammonium salt side chains on a SiO(2) surface was studied with the disjoining pressure measurements using atomic force microscopy. CPL shows a monotonic decrease in disjoining pressure as the film thickness increases from 1.3 to 4.5 nm, which suggests stable spreading in this thickness range. Comparing the spreading rates calculated from disjoining pressure and the viscosity of CLP to the self-healing time after tribo-contacts revealed that the ionic form may not be the main mobile species. The X-ray photoelectron spectroscopy analysis found that the CPL film on SiO(2) has about 30% of the quaternary ammonium salts (cationic groups) reduced to tertiary amines (neutral groups). The reduced CPL polymer has much lower viscosity than the original CPL polymer and yields a spreading rate consistent with that measured at the macroscale. Thus, the mobile component in the CPL/SiO(2) film responsible for self-healing is concluded to be the reduced tertiary amine components of CPL.     

Selective Ni-P electroless plating on photopatterned cationic adsorption films influenced by alkyl chain lengths of polyelectrolyte adsorbates and additive surfactants

We demonstrated that the photopatterned single-layer adsorption film of poly(1-dodecyl-4-pyridinium bromide) on a silica surface was available for a template of nickel-phosphorus (Ni-P) electroless plating through sensitization with a SnCl(2) aqueous solution and activation with a PdCl(2) aqueous solution. Four kinds of poly(1-alkyl-4-vinylpyridinium halide)s bearing methyl, propyl, hexyl, and dodecyl groups were prepared. The cationic polymers were adsorbed by a negatively charged silica surface from their solutions, to form single-layer adsorption films exhibiting desorption-resistance toward deionized water and ethanol. The organic adsorption films could be decomposed completely by exposure to 172 nm deep-UV light. The formation and decomposition of the single-layer films were confirmed by deep-UV absorption spectral measurement and zeta-potential measurement. Ni-P electroless plating was carried out on the photopatterned adsorption films, using three types of SnO(x) colloidal materials without and with cationic or anionic surfactant as catalyst precursors in the sensitization step. In the case of the negatively charged SnO(x) colloids surrounded by anionic surfactant, Ni-deposition took place preferentially on the cationic adsorption films remaining in unexposed regions. The Ni-deposition was accelerated significantly on the cationic adsorption film bearing dodecyl groups. It was obvious by ICP-AES analyses that the hydrophobic long-chain dodecyl groups in the adsorption film could promote the adsorption of the negative SnO(x) colloids on the film surface, followed by much nucleus formation of zerovalent Pd catalysts useful for the electroless plating. The result of our experiment clearly showed that, in addition to electrostatic interaction, van der Waals interaction generating between the hydrophobic long-chain hydrocarbons of the adsorption film and the surfactant improved significantly the adsorption stability of the SnO(x) colloids, resulting in highly selective Ni-deposition in accord with the photopattern shape of the cationic single-layer adsorption film.     

Polysaccharides as a template for silicate generated by sol-gel processes

The polysaccharides, as established previously (Yu.A. Shchipunov, J. Colloid Interface Sci. 268 (2003) 68; Yu.A. Shchipunov, T.Yu. Karpenko, Langmuir 20 (2004) 3882), can manipulate the formation of hybrid silica nanocomposites by sol-gel processes. Here atomic force microscopy was applied to show whether carbohydrate macromolecules serve as a template for silicate. Mica was used as a substrate to adsorb polysaccharide. It was found that its surface is not neutral to the sol-gel processes, providing the silica precipitation. To hinder it, the mica was protected by a monomolecular film of arachidic acid with the help of a Langmuir-Blodgett technique. Hydrophobically modified cationic hydrohyethylcellulose was adsorbed from a diluted aqueous solution. It was demonstrated that the carbohydrate macromolecules located on the hydrophobic surface did promote silica precipitation, serving as a template.     

Si/SiO2-templated formation of ultraflat metal surfaces on glass, polymer, and solder supports: their use as substrates for self-assembled monolayers

This paper describes the use of several methods of template stripping (TS) to produce ultraflat films of silver, gold, palladium, and platinum on both rigid and polymeric mechanical supports: a composite of glass and ultraviolet (UV)-curable adhesive (optical adhesive, OA), solder, a composite of poly(dimethyl siloxane) (PDMS) and OA, and bare OA. Silicon supporting its native oxide layer (Si/SiO2) serves as a template for both mechanical template stripping (mTS), in which the metal film is mechanically cleaved from the template, and chemical template stripping (cTS), in which the film-template composite is immersed in a solution of thiols, and the formation of the SAM on the metal film causes the film to separate from the template. Films formed on all supports have lower root-mean-square (rms) roughness (as measured by atomic force microscopy, AFM) than films used as-deposited (AS-DEP) by electron-beam evaporation. Monolayers of n-dodecanethiolate formed by the mTS and cTS methods are effectively indistinguishable by scanning tunneling microscopy (STM); molecularly resolved images could be obtained using both types of surfaces. The metal surfaces, before being cleaved, are completely protected from contact with the atmosphere. This protection allows metal surfaces intended to support SAMs to be prepared in large batch lots, stored, and then used as needed. Template stripping thus eliminates the requirement for evaporation of the film immediately before use and is a significant extension and simplification of the technology of SAMs and other areas of materials science requiring clean metal surfaces.     

In situ adsorption studies of a 14-amino acid leucine-lysine peptide onto hydrophobic polystyrene and hydrophilic silica surfaces using quartz crystal microbalance, atomic force microscopy, and sum frequency generation vibrational spectroscopy

The adsorption of a 14-amino acid amphiphilic peptide, LK14, which is composed of leucine (L, nonpolar) and lysine (K, charged), on hydrophobic polystyrene (PS) and hydrophilic silica (SiO2) was investigated in situ by quartz crystal microbalance (QCM), atomic force microscopy (AFM), and sum frequency generation (SFG) vibrational spectroscopy. The LK14 peptide, adsorbed from a pH 7.4 phosphate-buffered saline (PBS) solution, displayed very different coverage, surface roughness and friction, topography, and surface-induced orientation when adsorbed onto PS versus SiO2 surfaces. Real-time QCM adsorption data revealed that the peptide adsorbed onto hydrophobic PS through a fast (t < 2 min) process, while a much slower (t > 30 min) multistep adsorption and rearrangement occurred on the hydrophilic SiO2. AFM measurements showed different surface morphologies and friction coefficients for LK14 adsorbed on the two surfaces. Surface-specific SFG spectra indicate very different ordering of the adsorbed peptide on hydrophobic PS as compared to hydrophilic SiO2. At the LK14 solution/PS interface, CH resonances corresponding to the hydrophobic leucine side chains are evident. Conversely, only NH modes are observed at the peptide solution/SiO2 interface, indicating a different average molecular orientation on this hydrophilic surface. The surface-dependent difference in the molecular-scale peptide interaction at the solution/hydrophobic solid versus solution/hydrophilic solid interfaces (measured by SFG) is manifested as significantly different macromolecular-level adsorption properties on the two surfaces (determined via AFM and QCM experiments).     

C(膜)/Si(SiO2 )(纳米微粒)/C(膜)热处理的形态及结构分析

用直流辉光溅射+真空镀膜法制备了一种新型结构的硅基纳米发光材料- C(膜)/Si(SiO2)(纳米微粒)/C(膜)夹层膜,并对其进行了退火处理.用TEM、 SEM、 XRD和XPS对其进行了形态结构分析.TEM观察表明: Si(SiO2)纳米微粒基本呈球形,粒径在30 nm左右.SEM观察表明: 夹层膜样品总厚度约为50 μm,膜表面比较平整、致密.400℃退火后,样品表面变得凹凸不平,出现孔状结构; 650℃退火后,样品表面最平整、致密且颗粒均匀.XRD分析表明:制备出的夹层膜主要由SiO2和Si组成,在C原子的还原作用和氧气的氧化作用的共同作用下, SiO2和Si的含量随加热温度的升高而呈现交替变化: 400℃时, C的还原作用占主导地位, SiO2几乎全部被还原成了Si,此时Si含量最高; 400～650℃时,氧化作用占主导地位, Si又被氧化成SiO2, Si含量降低, SiO2含量逐渐上升,在650℃达到最高.XPS分析表明: 在加热过程中, C原子逐渐扩散进入Si(SiO2)微粒层,在650℃与Si反应生成了新的SiC.     

Bonding self-assembled, compact organophosphonate monolayers to the native oxide surface of silicon

A new method is described to prepare strongly bonded, compact monolayer films of alkyl- or arylphosphonates on the native oxide surface of Si (SiO(2)/Si). This method is illustrated for octadecyl- and alpha-quarterthiophene-2-phosphonates. For both cases, AFM shows comprehensive coverage of the SiO(2)/Si surface. The thickness of the continuous film of 4TP/SiO(2)/Si was measured both by AFM and by X-ray reflectivity to be ca. 18 A. Direct gravimetric analysis shows surface coverage by alpha-quarterthiophene-2-phosphonate to be about 0.66 nmol/cm(2), which corresponds to molecular packing in the film close to that of crystalline alpha-quarterthiophene. Coverage by octadecylphosphonate was ca. 0.90 nmol/cm(2), corresponding to a cross-sectional area of about 18.5 A(2)/molecule, consistent with close-packed alkyl chains.     

Controlled growth of micropatterned, oriented calcite films on a self-assembled multilayer film

A micropatterned multilayer film, which was fabricated from layer-by-layer electrostatic self-assembly of nitrodiazoresin (NDR)/poly(acrylic acid) (PAA) followed by photolithography, was utilized as a structured template for the biomimetic mineralization of calcium carbonate. Micropatterned CaCO3 films consisting of regularly aligned calcite crystals oriented in the <104> direction were selectively deposited on the patterned NDR/PAA multilayer film.     

Anisotropic polymerization of a long-chain diacetylene derivative Langmuir-Blodgett film on a step-bunched SiO2/Si surface

Alternating facet/terrace nanostructures were fabricated on a SiO2 surface by step-bunching and thermal oxidation of a vicinal Si(111) substrate, and their influence upon the polymerization direction of a long-chain diacetylene derivative monolayer film was investigated by angle-dependent polarized near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. It was found that the peak intensity of the C 1s-pi transition was stronger when the electric vector plane of the incident X-ray was parallel to the direction of the periodic facet/terrace structures rather than perpendicular to them. On the contrary, a polymer film fabricated on a flat SiO2 surface showed no in-plane anisotropy of the peak intensity. These results indicate that the diacetylene groups in the diacetylene derivative monolayer are preferentially photopolymerized in the direction not across but along the periodic one-dimensional structures on the step-bunched and thermally oxidized SiO2/Si(111) surface.     

Key factors determining the course of methyl iodide oxidative addition to diamidonaphthalene-bridged diiridium(I) and dirhodium(I) complexes

The course of methyl iodide oxidative addition to various nucleophilic complexes, [Ir2(mu-1,8-(NH)2naphth)(CO)2(PiPr3)2] (1), [IrRh(mu-1,8-(NH)2naphth)(CO)2(PiPr3)2] (2), and [Rh2(mu-1,8-(NH)2naphth)(CO)2(PR3)2] (R = iPr, 3; Ph, 4; p-tolyl, 5; Me, 6), has been investigated. The CH3I addition to complex 1 readily affords the diiridium(II) complex [Ir2(mu-1,8-(NH)2naphth)I(CH3)(CO)2(PiPr3)2] (7), which undergoes slow rearrangement to give a thermodynamically stable stereoisomer, 8. The reaction of the Ir-Rh complex 2 gives the ionic compound [IrRh(mu-1,8-(NH)2naphth)(CH3)(CO)2(PiPr3)2]I (10). The dirhodium compounds, 3-5, undergo one-center additions to yield acyl complexes of the formula (Rh2(mu-1,8-(NH)2naphth)I(COCH3)(CO)(PR3)2] (R = iPr, 12; Ph, 13; p-tolyl, 14). The structure of 12 has been determined by X-ray diffraction. Further reactions of these Rh(III)-Rh(I) acyl derivatives with CH3I are productive only for the p-tolylphosphine derivative, which affords the bis-acyl complex [Rh2(mu-1,8-(NH)2naphth)(CH3CO)2I2(P(p-tolyl)3)2] (15). The reaction of the PMe3 derivative, 6, allows the isolation of the bis-methyl complex [Rh2(mu-1,8-(NH)2naphth)(mu-I)(CH3)2(CO)2(PMe3)2]I (16a), which emanates from a double one-center addition. Upon reaction with methyl triflate, the starting materials, 1, 2, 3, and 6, give the isostructural cationic methyl complexes 9, 11, 17, and 18, respectively. The behavior of these cationic methyl compounds toward CH3I, CH3OSO2CF3, and tetrabutylamonium iodide is consistent with the role of these species as intermediates in the SN2 addition of CH3I. Compounds 18 and 17 react with an excess of methyl triflate to give [Rh2(mu-1,8-(NH)2naphth)(mu-OSO2CF3)(CH3)2(CO)2(PMe3)2][CF3SO3] (19) and [Rh2(mu-1,8-(NH)2naphth)(OSO2CF3)(COCH3)(CH3)(CO)(PiPr3)2][CF3SO3] (20), respectively. Upon treatment with acetonitrile, complexes 17 and 18 give the isostructural cationic acyl complexes [Rh2(mu-1,8-(NH)2naphth)(COCH3)(NCCH3)(CO)(PR3)2][CF3SO3] (R = iPr, 21; Me, 22). A kinetic study of the reaction leading to 21 shows that formation of these complexes involves a slow insertion step followed by the fast coordination of the acetonitrile. The variety of reactions found in this system can be rationalized in terms of three alternative reaction pathways, which are determined by the effectiveness of the interactions between the two metal centers of the dinuclear complex and by the steric constraints due to the phosphine ligands.     

ZSM-35 分子筛的静态合成和晶化机理

 以环己胺为有机模板剂, 硅溶胶为硅源, 采用静态合成法在 220 ºC 的水热体系中制得了 ZSM-35 分子筛纯相. 当初始凝胶中含有一定量的 K+时, 在晶化过程中, K+与Na+的共同作用可以很好地抑制混晶丝光沸石的生成, 且当 n(K+)/n(K+ + Na+) = 0.3 时, 制得的 ZSM-35 分子筛晶化度最高. 利用 X 射线衍射和紫外拉曼光谱对分子筛形成的最佳条件以及晶化机理进行了研究. 发现合成初期前体中含有五元环和六元环的硅物种构筑单元. 通过水热晶化过程, 与硅酸盐的五元环或六元环有关的 450 cm–1 处紫外拉曼谱峰增强, 在晶化后期, 随着无定形凝胶逐渐被消耗, 在 421, 312 和 215 cm–1 处出现新的 ZSM-35 结构的特征拉曼谱峰, 说明这些环物种相互聚集最终形成了 ZSM-35 分子筛.     

Synthesis and characterization of cyclotriphosphazenes containing silicon as single solid-state precursors for the formation of silicon/phosphorus nanostructured materials

The synthesis and characterization of new organosilicon derivatives of N(3)P(3)Cl(6), N(3)P(3)[NH(CH(2))(3)Si(OEt)(3)](6) (1), N(3)P(3)[NH(CH(2))(3)Si(OEt)(3)](3)[NCH(3)(CH(2))(3)CN](3) (2), and N(3)P(3)[NH(CH(2))(3)Si(OEt)(3)](3)[HOC(6)H(4)(CH(2))CN](3) (3) are reported. Pyrolysis of 1, 2, and 3 in air and at several temperatures results in nanostructured materials whose composition and morphology depend on the temperature of pyrolysis and the substituents of the phosphazenes ring. The products stem from the reaction of SiO(2) with P(2)O(5), leading to either crystalline Si(5)(PO(4))(6)O, SiP(2)O(7) or an amorphous phase as the glass Si(5)(PO(4))(6)O/3SiO(2).2P(2)O(5), depending on the temperature and nature of the trimer precursors. From 1 at 800 degrees C, core-shell microspheres of SiO(2) coated with Si(5)(PO(4))(6)O are obtained, while in other cases, mesoporous or dense structures are observed. Atomic force microscopy examination after deposition of the materials on monocrystalline silicon wafers evidences morphology strongly dependent on the precursors. Isolated islands of size approximately 9 nm are observed from 1, whereas dense nanostructures with a mean height of 13 nm are formed from 3. Brunauer-Emmett-Teller measurements show mesoporous materials with low surface areas. The proposed growth mechanism involves the formation of cross-linking structures and of vacancies by carbonization of the organic matter, where the silicon compounds nucleate. Thus, for the first time, unique silicon nanostructured materials are obtained from cyclic phosphazenes containing silicon.     

Biomimetic deposition of silica templated by a cationic polyamine-containing microgel

We report using poly(acrylamide-co-2-(dimethylamino)ethyl methacrylate, methyl chloride quaternized) cationic microgels as a porous colloidal template for biomimetic in situ silica mineralization, allowing the well-controlled synthesis of submicrometer-sized hybrid microgel--silica particles and porous silica particles by subsequent calcination. The microgels were prepared by inverse emulsion polymerization in the presence of a bisacrylamide cross-linker. Silica deposition was achieved by simply stirring an aqueous mixture of the microgel particles and tetramethyl orthosilicate (TMOS) at 20 degrees C for 30 min. No experimental evidence was found for nontemplated silica, which indicated that silica deposition occurred exclusively within the cationic microgel template particles. The resulting microgel-silica hybrid particles were characterized by electron microscopy, dynamic light scattering, FT-IR spectroscopy, 1H NMR and solid-state 29Si magic angle spinning NMR spectroscopy, thermogravimetry, aqueous electrophoresis, and surface area measurements. Aqueous electrophoresis studies confirmed that the hybrid microgel-silica particles had positive zeta potentials over a wide pH range and isoelectric points could be tuned by varying the synthesis conditions. This suggests that these particles could form complexes with DNA for improved gene delivery. The porosity of the calcined silica particles could be controlled by varying the amount of TMOS, suggesting potential encapsulation/controlled release applications.     

共沉淀法掺杂SiO_2对V_2O_5-WO_3/TiO_2催化剂SCR性能的影响

通过共沉淀法将SiO_2组分掺入到V2O5-WO3/SiO_2-TiO_2催化剂TiO_2载体中,并通过多种物理化学手段,考察了不同SiO_2掺杂量对催化剂结构、表面性质与SCR性能的影响.结果表明,SiO_2掺入到TiO_2中,Si与Ti形成Si—O—Ti键,使催化剂比表面积增加.Si—O—Ti键的生成以及Si Ox物种上的-OH基团使催化剂表面Br?nsted酸增加,但新增的Br?nsted酸对SCR反应不利,并且SiO_2的掺杂也使得V~(5+)含量降低,Si—O—V键合作用使分散的VOx物种更难还原.Si组分以共沉淀法掺入到V_2O_5-WO_3/TiO_2催化剂会造成脱硝活性的显著下降.     

Protonation of a lanthanum phosphide-alkyl occurs at the P-La not the C-La bond: isolation of a cationic lanthanum alkyl complex

Protonation of the heteroleptic, cyclometalated lanthanum phosphide complex [((Me3Si)2CH)(C6H4-2-CH2NMe2)P]La(THF)[P(C6H4-2-CH2NMe2)(CH(SiMe3)(SiMe2CH2))] with [Et3NH][BPh4] yields the cationic alkyllanthanum complex [(THF)4La[P(C6H4-2-CH2NMe2)(CH(SiMe3)(SiMe2CH2))]][BPh4].