Development of a validated liquid chromatographic method for the determination of related substances and assay of tenofovir disoproxil fumarate

The present study describes the development and validation of a selective liquid chromatographic (LC) method for the analysis of tenofovir disoproxil fumarate (TDF) and its related substances. The gradient method uses a base deactivated C18 column (Hypersil BDS column; 25 cm×4.6 mm I.D.) maintained at a temperature of 30°C. The mobile phases consist of acetonitrile, tetrabutylammonium/phosphate buffer pH 6.0 and water: (A; 2:20:78 v/v/v) and (B; 65:20:15 v/v/v). The flow rate is 1.0 mL/min and UV detection is performed at 260 nm. Good separation of TDF and 21 impurities was achieved. A system suitability test (SST) to check the quality of separation is also specified. The developed method was further validated with respect to robustness, precision, sensitivity and linearity. The method is proved to be robust, precise, sensitive and linear between 0.1 μg/mL and 0.15 mg/mL. The limit of detection and limit of quantification are 0.03 and 0.1 μg/mL, respectively. The method was successfully applied to the quantification of related substances and assay of commercial TDF samples (bulk substances and tablets).     

Analysis of metformin dosage formulations by capillary electrophoresis at nano scale detection

An inexpensive, rapid and reproducible capillary electrophoretic method has been developed and validated for the determination of metformin in pharmaceutical preparations. The method was developed utilizing a fused silica capillary (60 cm x 50 microm I.D.), phosphate buffer (50 mM, 3.0 pH)-acetonitrile (95:5, v/v) as background electrolyte (BGE), 20 kV applied voltage with UV detection at 254 nm and at a working temperature of 23 +/- 1 degrees C. Linearity was observed in the concentration range from 100 ng/L to 5 microg/L, with a correlation coefficient (R2) of 0.9998. The limits of detection and quantification achieved were 60 and 100 ng/mL, respectively. The recovery of metformin from pharmaceutical preparations was 99.1%. These validation parameters demonstrate the precision of the method and its suitability for the determination of metformin in pharmaceutical tablet formulations.     

Simultaneous separation and determination of 20 potential adulterant antigout and antiosteoporosis pharmaceutical compounds in herbal food products using LC with electrospray ionization MS/MS and LC with quadrupole‐time‐of‐flight MS

An analytical method for the simultaneous and reliable determination of 20 antigout and antiosteoporosis pharmaceutical compounds in adulterated health food products was developed using liquid chromatography with electrospray ionization tandem mass spectrometry and liquid chromatography with quadrupole‐time‐of‐flight mass spectrometry. The method was validated through the determination of specificity, linearity, limit of detection, and limit of quantification, method detection limit, method quantitation limit, precision, accuracy, recovery, and stability. The matrix effect was also determined. The validation results of the developed method are as follows: for solid and liquid blank samples, limits of detection ranged from 0.05 to 5.00 ng/mL and limits of quantification ranged from 0.15 to 15.00 ng/mL. Linearity was acceptable, and the correlation coefficients (R²) were ≥0.99 for all target compounds. Both intra and interday precision were less than 9.16% RSD, and accuracies ranged from 95.31 to 116.68%. Mean recoveries for different types of dietary supplements classified as powders, liquids, tablets, and capsules were found to be 80.81 to 117.62% with less than 15.00% relative standard deviation. The stability of the standard mixture solution was less than 11.72% relative standard deviation after 48 h. By the proposed method, the presence of dexamethasone was determined in seized herbal food products at concentrations that ranged from 126 to 215 µg/g.     

A Novel Ultra-High Performance Liquid Chromatography Method for the Determination of Erdosteine,Related Impurities and Degradation Products in New Effervescent Tablets

A novel and automated, stability-indicating, reversed phase ultra performance liquid chromatography (UPLC) method was developed and validated for the quantitative determination of erdosteine, its known impurities and two novel degradation products in a new pharmaceutical dosage form (effervescent tablets). The chromatographic separations were performed on a Waters Acquity UPLC HSS T3, 1.8 µm (2.1 mm?×?150 mm, I.D.) stainless steel column. The mobile phase consisted of 0.1% TFA in water and methanol under gradient elution conditions, at a flow rate of 0.29 mL/min, for the assay and impurities analysis. UV detection was set at a wavelength of 238 nm. Erdosteine raw material, placebo and effervescent tablets were subjected to forced degradation. The new degradation products (labeled OX1 and OX2) were found after oxidative treatment and characterized by ultra performance liquid chromatography mass spectrometry. The validation parameters such as linearity, limit of detection (LOD) and quantification (LOQ), accuracy, precision, specificity and robustness were highly satisfactory for all analyzed compounds. LOD (0.020 and 0.011–0.385 µg/mL for erdosteine and impurities, respectively) and LOQ values show the high sensibility of the method. Specificity of the method was confirmed by testing the matrix components. The validated method demonstrated to be suitable for routine quality control purposes and for routine stability studies of erdosteine in effervescent formulations.     

Validated RP-HPLC method for determination of permethrin in bulk and topical preparations using UV-vis detector

An isocratic reversed-phase high-performance liquid chromatographic method for the estimation of permethrin in raw materials and pharmaceutical topical preparations has been devised and validated. The chromatographic analysis was performed on a 5 μm particle C-18 Nucleosil (Macherey-Nagel, Germany) column (250 × 4.6 mm). Mobile phase consisted of methanol and 0.025 mM Phosphoric acid (85:15 v/v) at a flow rate of 1.5 mL/min. UV detection was performed at 272 nm and peaks were identified with retention times as compared with standards. The limit of detection was 1.782 μg/mL, while limit of quantitation was 48.0 μg/mL. The calibration was linear in a concentration range of 48.0-5000 μg/mL with correlation coefficient of 0.999978. Regression equation was absorbance =2833.23 × concentration(μg/mL) + 19.1045 with variance of the response variable, S(yx)(2), calculated to be 1.75328 (six degrees of freedom). The method was validated as per ICH guidelines and USP requirements and found advantageous for the routine analysis of the drug in pharmaceutical formulations and in pharmaceutical investigations involving permethrin.     

Simultaneous quantification of curcuminoids and xanthorrhizol in Curcuma xanthorrhiza by high-performance liquid chromatography

A new method for simultaneous quantification of curcuminoids and xanthorrhizol (XNT) in Curcuma xanthorrhiza was developed and validated using high-performance liquid chromatography with diode-array UV–Vis detector. The chromatographic separation was achieved on a Phenomenex C18 at room temperature with the mobile-phase acetonitrile ?0.001% formic acid in gradient elution system and delivered at a flow rate of 1?mL/min. Detection wavelength 425?nm was used for curcuminoids and 224?nm for XNT. System suitability, linearity, precision, accuracy, limit of detection, limit of quantitation, and stability were evaluated and were found in good agreement with Association of Official Analytical Chemists guidelines for single-laboratory validation. The proposed method was found to be precise, accurate, and reliable and also could be applied for the simultaneous quantitative analysis of curcuminoids and XNT in C. xanthorriza raw material and its herbal medicinal product.     

A simple HPLC-DAD method for determination of adapalene in topical gel formulation

A simple stability indicating high-performance liquid chromatography method for the analysis of adapalene in pharmaceutical gel formulation is developed and validated. An isocratic separation is performed using a Merck RP-8 (150 mm × 4.6 mm i.d., particle size 5 m) column and a mixture of acetonitrile water (67:33, v/v, pH adjusted to 2.5 with phosphoric acid) as the mobile phase. The detection is achieved with a photodiode array detector at 321 nm. The specificity of the method is verified by subjecting both the reference substance and the pharmaceutical form to hydrolytic, oxidative, photolytic, and thermal stress conditions. There is no interference from the excipients of the formulation on the determination of adapalene in gel. The response is linear over the concentration range of 8.0-16.0 μg/mL (r > 0.999) with a limit of detection and quantification of 0.04 and 0.14 μg/mL, respectively. The mean recovery is 100.8%. The RSD values for the intra- and inter-day precision studies are < 1.2%. The method is validated by reaching satisfactory results for linearity, selectivity, specificity, precision, accuracy, robustness, and system suitability.     

Development and validation of the HPLC method for the analysis of trimetazidine hydrochloride in bulk drug and pharmaceutical dosage forms

A simple, economic, selective, precise, and accurate high-performance liquid chromatographic (HPLC) method for the analysis of trimetazidine hydrochloride in both bulk drug and pharmaceutical formulations was developed and validated in the present study. The mobile phase consisted of water: methanol: triethylamine (75: 25: 0.1 v/v/v), and pH 3.3 was adjusted with orthophosphoric acid. This system was found to give a sharp peak of trimetazidine hydrochloride at a retention time of 3.375 ± 0.04 min. HPLC analysis of trimetazidine hydrochloride was carried out at a wavelength of 232 nm with a flow rate of 1.0 mL/min. The linear regression analysis data for the calibration curve showed a good linear relationship with a regression coefficient of 0.997 in the concentration range of 5–90 μg/mL. The linear regression equation was y = 35362x − 8964.2. The limit of detection (LOD) and limit of quantification (LOQ) were found to be 3.6 and 10.9 μg/mL, respectively. The developed method was employed with a high degree of precision and accuracy for the analysis of trimetazidine hydrochloride. The developed method was validated for accuracy, precision, robustness, detection, and quantification limits as per the ICH guidelines. The wide linearity range, accuracy, sensitivity, short retention time, and composition of the mobile phase indicated that this method is better for the quantification of trimetazidine hydrochloride. The text was submitted by the authors in English.     

Simultaneous Determination of Ceftriaxone Sodium and Non Steroidal Anti‐Inflammatory Drugs in Pharmaceutical Formulations and Human Serum by RP‐HPLC

An accurate, sensitive and least time consuming reverse phase high performance liquid chromatographic (RP‐HPLC) method for the estimation of ceftriaxone in the presence of non steroidal anti‐inflammatory drugs in formulation and human serum has been developed and validated. Chromatographic separation was conducted on prepacked Purospher Star, C18 (5 μm, 250 × 4.6 mm) column at room temperature using methanol:water:acetonitrile (80:15:5 v/v/v) as a mobile phase, pH adjusted at 2.8 with ortho‐phosphoric acid and at a flow rate of 1.0 mL/minute, while UV detection was performed at 270 nm. The results obtained showed a good agreement with the declared content. The method shows good linearity in the range of 2.5‐25 μg/mL ceftriaxone serum concentrations with a correlation coefficient 0.999 (inter‐ and intra‐day RSD < 2.0%). The limit of detection and quantification for ceftriaxone and NSAID's in pharmaceutical formulation and serum were in the range 0.51‐1.54 μg/mL. Analytical recovery was >98.1%. The proposed method may be used for the quantitative analysis of commonly administered non steroidal anti‐inflammatory drugs i.e. tiaprofenic acid, naproxen sodium, flurbiprofen, diclofenac acid and mefenamic acid alone or in combination with ceftriaxone from raw materials, dosage formulations and in serum. The established HPLC method is rapid, accurate and selective, because of its sensitivity and reproducibility.     

Chromatographic method for clobetasol propionate determination in hair follicles and in different skin layers

Clobetasol propionate (CLO) is a potent steroid used for the treatment of several dermatological diseases. Recent studies suggest its additional use in alopecia topical treatment, generating a demand for novel formulations with specific delivery into hair follicles. Hence, a selective analytical method for drug quantification in follicular structures and skin layers is required. For this, a simple HPLC‐UV method was developed. Quantification was performed using a RP‐C₁₈ column (4.6 mm × 15 cm, 5 μm), with a mixture of methanol–acetonitrile–water (50:15:35 v /v) as mobile phase, a flow rate of 1.2 mL/min, oven temperature of 30°C, injection volume of 50 μL and detection at 240 nm. The optimized conditions enabled a 12 min running with CLO elution at 10.1 min and resolution of 2.424 from skin matrix interferences. Validation was performed in accordance with International Conference on Harmonization guidelines and fulfilled the criteria of selectivity, linearity (0.5–15.0 μg/mL), robustness, precision, accuracy and limits of detection and quantification (0.02 and 0.07 μg/mL, respectively). The validated method was successfully applied for CLO quantification following in vitro skin permeation experiments and differential tape‐stripping for hair follicle deposition determination, demonstrating its suitability.     

Simultaneous quantification of cefpirome and cetirizine or levocetirizine in pharmaceutical formulations and human plasma by RP-HPLC

A rapid and sensitive high-performance liquid chromatographic (HPLC) assay for the simultaneous determination and quantification of cefpirome and cetirizine or cefpirome and levocetirizine in pharmaceutical formulations and human plasma without changing the chromatographic conditions is described. Chromatographic separations were performed on a prepacked Nucleosil 120, C₁₈ (5 μm, 12.5 ± 0.46 mm) column using CH₃CN: H₂O (75: 25, v/v) as a mobile phase at a flow rate of 1 mL/min while UV detection was performed at 232 nm for monitoring the effluent. A number of other brands of C₁₈ columns were also employed which had a significant effect on the separation. The method has been validated over the concentration range of 0.5–50 μg/mL (r ₂ > 0.999). The limit of detection (LOD) and quantification (LOQ) for cefpirome and levocetirzine in pharmaceutical formulations and serum were in the range 0.24–1.31 μg/mL. Analytical recovery from human plasma was >98%, and the within and between-day relative standard deviation was <3.1%. The small sample volume and simplicity of preparation make this method suitable for use in pharmaceutical industries, drug research centers, clinical laboratories, and forensic medical centers. The text was submitted by the authors in English.     

Highly Selective and Sensitive Graphene Based Electrochemical Sensor for Quantification of Receptor Agonist Rizatriptan

A highly selective and sensitive electrochemical sensor has been developed by modification of a glassy carbon electrode (GCE) with graphene (GRP) for quantification of Rizatriptan. The significant increase of the peak current and the improvement of the oxidation peak potential indicate that the electrochemical sensor facilitates the electron transfer of Rizatriptan. The oxidation peak current was proportional to the Rizatriptan concentration in the range from 100 to 600 µg/mL with detection (LOD) and quantification limit (LOQ) of 36.52 and 121.73 µg/mL, respectively. The developed method was successfully employed for quantification of Rizatriptan in pharmaceutical formulations. The sensor shows great promise for simple, sensitive and quantitative detection of Rizatriptan.     

Development and validation of a generic liquid chromatographic method for the simultaneous determination of five commonly used antimalarial drugs: Application to pharmaceutical formulations and human plasma

A simple, sensitive, and rapid liquid chromatographic method was developed and validated using diode array detection for the determination of five commonly used antimalarial drugs in pharmaceutical formulations and in human plasma. Chromatographic separation of antimalarial drugs and internal standard (ibuprofen) was achieved on a C₁₈ column with a mobile phase composed of 10 mM dipotassium orthophosphate at pH 3.0, methanol, and acetonitrile in a ratio of 20:38:42 v/v, at a flow rate of 1 mL/min. The analytes were monitored at 220 nm and separated in ?10 min. The method was validated for linearity, accuracy, precision, limit of quantification, and robustness. Both intra‐ and interday precisions (in terms of %RSD) were lower than 3% and accuracy ranged from 98.1 to 104.5%. Extraction recoveries were ≥96% in plasma. The limits of quantitation for artemether, lumefantrine, pyrimethamine, sulfadoxine, and mefloquine were 0.3, 0.03, 0.06, 0.15, and 0.15 μg/mL in human plasma. Stability under various conditions was also investigated. The method was successfully applied for quantification of antimalarial drugs in marketed formulations and in spiked human plasma. The method can be employed for routine QC purposes and in pharmacokinetic investigations.     

Kinetic Spectrofluorometric Determination of Thioctic Acid in Bulk and Pharmaceutical Preparations via its Oxidation with Cerium(IV)

A highly simple and sensitive kinetic spectrofluorometric method was developed for the determination of thioctic acid. The method is based on the oxidation of the studied drug with cerium(IV) ammonium sulfate in acidic medium. The fluorescence of the produced Ce(III) was measured at 365 nm after excitation at 255 nm. The different experimental parameters affecting the development and stability of the reaction product were carefully studied and optimized. The method is applicable over the concentration range of 0.02 to 0.12 μg/mL with a detection limit of 6.06 × 10^?3 μg/mL and a quantification limit of 0.02 μg/mL. The method was successfully applied for the assay of the studied drug in pharmaceutical formulations. The results obtained were in good agreement with those obtained with the reference method.     

Purity assessment of recombinant human granulocyte colony‐stimulating factor in finished drug product by capillary zone electrophoresis

Current methods for determination of impurities with different charge‐to‐volume ratio are limited especially in terms of sensitivity and precision. The main goal of this research was to establish a quantitative method for determination of impurities with charges differing from that of recombinant human granulocyte colony‐stimulating factor (rhG‐CSF, filgrastim) with superior precision and sensitivity compared to existing methods. A CZE method has been developed, optimized, and validated for a purity assessment of filgrastim in liquid pharmaceutical formulations. Optimal separation of filgrastim from the related impurities with different charges was achieved on a 50 μm id fused‐silica capillary of a total length of 80.5 cm. A BGE that contains 100 mM phosphoric acid adjusted to pH 7.0 with triethanolamine was used. The applied voltage was 20 kV while the temperature was maintained at 25°C. UV detection was set to 200 nm. Method was validated in terms of selectivity/specificity, linearity, precision, LOD, LOQ, stability, and robustness. Linearity was observed in the concentration range of 6–600 μg/mL and the LOQ was determined to be 0.3% relative to the concentration of filgrastim of 0.6 mg/mL. Other validation parameters were also found to be acceptable; thus the method was successfully applied for a quantitative purity assessment of filgrastim in a finished drug product.     

Method development and validation for the determination of indiquinoline tartrate, a novel kappa opioid agonist, and its related substances by high-performance liquid chromatography

A stability-indicating reversed-phase high-performance liquid chromatography method has been developed and validated for the assay of indiquinoline tartrate and its related substances. The method was established by forced degradation experiments and system suitability experiments. The chromatographic separation was achieved with a Hedera ODS-3 column (5 μm, 250 mm × 4.6 mm) and the mobile phase was constituted (flow rate 1.0 mL/min) of eluant A, aqueous acetate buffer and eluant B, CH(3)OH using a gradient elution. A photodiode array detector set at 254 nm was used for detection. The investigated validation elements showed that the method has acceptable specificity, accuracy, linearity, precision, robustness and high sensitivity with limit of detection and limit of quantitation. The method can be used for routine quality control analysis and stability testing of indiquinoline tartrate drug substance.     

UV spectrophotometric determination of bioflavonoids from a semisolid pharmaceutical dosage form containing Trichilia catigua Adr. Juss and Ptychopetalum olacoides Bentham standardized extract: analytical method validation and statistical procedures

A precise, accurate, and sensitive UV spectrophotometric method was developed and validated for routine quantification of total bioflavonoids, expressed as rutin, from a topical oil-in-water pharmaceutical emulsion containing the extract of Trichilia catigua Adr. Juss and Ptychopetalum olacoides Bentham. The method was validated experimentally, and the data were treated rigorously by statistical analysis. The following analytical parameters were assessed: linearity, specificity, intra- and interrun precision measured as relative standard deviation (RSD, %), intra- and interrun accuracy (E, %), recovery (Rec., %), limit of detection (LOD, microg/mL), and limit of quantification (LOQ, microg/mL). The UV spectrophotometric method was linear (r = 0.9995) for standard rutin over the concentration range of 5.0-15.0 microg/mL with specificity for total bioflavonoids (expressed as rutin) at 361.0 nm with an absence of interferents from the complex matrix; RSD of < or = 1.79%, intrarun (E = 97.88 +/- 1.75 to 99.0 +/- 0.33%) and interrun (E = 98.38 +/- 1.12 to 100.79 +/- 1.30%) accuracy; Rec. = 98.64 +/- 0.42 to 100.74 +/- 0.41%; LOD = 0.20 microg/mL; and LOQ = 0.30 microg/mL.     

Simultaneous determination of atenolol and amiloride in pharmaceutical preparations by capillary zone electrophoresis with capacitively coupled contactless conductivity detection

Capillary zone electrophoresis coupled with a capacitively coupled contactless conductivity detector (CE‐C⁴D) has been employed for the determination of atenolol and amiloride in pharmaceutical formulations. Acetic acid (150 mm ) was used as background electrolyte. The influence of several factors (detector excitation voltage and frequency, buffer concentration, applied voltage, capillary temperature and injection time) was studied. Non‐UV‐absorbing L‐valine was used as internal standard; the analytes were all separated in less than 7 min. The separation was carried out in normal polarity mode at 28°C, 25 kV and using hydrodynamic injection (25 s). The separation was effected in an uncoated fused‐silica capillary (75 μm, i.d. × 52 cm). The CE‐C⁴D method was validated with respect to linearity, limit of detection and quantification, accuracy, precision and selectivity. Calibration curves were linear over the range 5–250 μg/mL for the studied analytes. The relative standard deviations of intra‐ and inter‐day migration times and corrected peak areas were less than 6.0%. The method showed good precision and accuracy and was successfully applied to the simultaneous determination of atenolol and amiloride in different pharmaceutical tablet formulations. Copyright © 2010 John Wiley & Sons, Ltd.     

A novel validated LC method for quantitation of lopinavir in bulk drug and pharmaceutical formulation in the presence of its potential impurities and degradation products

A simple isocratic liquid chromatographic method was developed for determination of lopinavir from its related impurities and assay for the first time. This method involves the use of a C(8) (Symmetry Shield RP8, 150 x 4.6 mm, 5 microm) column. The method was validated over the range of limit of quantitation (LOQ) to 120% of impurity specification limit and LOQ to 150% of working concentration for assay. The mobile phase consisted of a mixture of 50 mM of potassium phosphate buffer, acetonitrile and methanol in the ratio of 40:50:10. The flow rate was set at 1.0 mL/min with UV detection monitored at 210 nm. The drug was subjected to stress conditions of hydrolysis, oxidation, photolysis and thermal degradation. The developed method was validated for linearity, range, precision, accuracy and specificity. This method was successfully applied for content determination of lopinavir in pharmaceutical formulations. The method can be conveniently used in a quality control laboratory for routine analysis for assay and related substances as well for the evaluation of stability samples of bulk drugs and pharmaceutical formulations.     

Determination of eprosartan mesylate and hydrochlorothiazide in tablets by derivative spectrophotometric and high-performance liquid chromatographic methods

Two new simple and selective assay methods have been presented for the analysis of eprosartan mesylate (EPR) and hydrochlorothiazide (HCT) in pharmaceutical formulations. The first method is based on first-derivative ultraviolet spectrophotometry with zero-crossing measurements at 246 and 279 nm for EPR and HCT, respectively. The assay was linear over the concentration ranges 3.0-14.0 μg/mL for EPR and 1.0-12.0 μg/mL for HCT. The quantification limits for EPR and HCT were found to be 1.148 and 0.581 μg/mL, respectively, while the detection limits were 0.344 μg/mL for EPR and 0.175 μg/mL for HCT. The second method involved isocratic reversed-phase liquid chromatography using a mobile phase composed of acetonitrile-10 mM phosphoric acid (pH 2.5) (40:60, v/v). Olmesartan was used as internal standard and the substances were detected at 272 nm. The linearity ranges were found to be 0.5-30 and 0.3-15.0 μg/mL for EPR and HCT, respectively. The limits of detection were found to be 0.121 μg/mL for EPR and 0.045 μg/mL for HCT. The limits of quantification were found to be 0.405 and 0.148 μg/mL for EPR and HCT, respectively. The proposed methods were successfully applied to the determination of commercially available tablets with a high percentage of recovery and good accuracy and precision.