Thermal and FTIR Characterization of Films Obtained From Carbopol/Surfactant Aqueous Solutions

Journal of Thermal Analysis and Calorimetry - The suitability of differential scanning calorimetry (DSC) as a routine technique to characterize polymer/surfactant interactions in aqueous medium was...     

Thermorheological properties of LLDPE/LDPE blends: Effects of production technology of LLDPE

The thermorheological behavior of a number of LLDPE/LDPE blends was studied with emphasis on the effects of the production technology of the linear low‐density polyethylene (LLDPE) and the effects of long chain branching (LCB). Two Ziegler‐Natta LLDPE's (LL3001.32 and Dowlex2045G) and two metallocene LLDPEs (AffinityPL1840 and Exact 3128) were blended with a single low‐density polyethylene (LDPE), with all LLDPEs having distinctly different molecular weight. The weight fractions of the LDPEs used in the blends were 1, 5, 10, 20, 50, and 75%. DSC analysis has shown that the blends with metallocence LLDPEs are miscible in the crystal state, whereas for the Ziegler‐Natta, apart from the two distinct peaks of the individual components, a third peak appears which indicates the existence of a third phase that is created from the cocrystallization of components from the two blended polymers. The linear viscoelastic characterization was performed and mastercurves at 150 °C were constructed for all blends to check miscibility using the time temperature superposition principle. In addition, Van Gurp Palmen and zero‐shear viscosity versus composition were constructed to check the thermorheological behavior of all blends. In general, good agreement is found among these various methods. It was concluded that metallocene LLDPEs are more compatible with LDPE at all LDPE compositions when compared with their Ziegler‐Natta counterparts. Finally, the extensional properties of all blends were studied to examine the effects of different levels of LCB on their extensional rheological properties. It was concluded that extensional rheology is a sensitive tool capable of detecting subtle changes in the polyethylene macrostructure, that is, low levels of LCB. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1669–1683, 2008     

用红外光谱研究具有互穿网络结构的pH/温度双重敏感性微凝胶的相转变行为

采用傅立叶变换红外光谱仪测试了由聚(N-异丙基丙烯酰胺)(PNIPA)和聚丙烯酸(PAA)两种聚合物网络形成的具有互穿聚合物网络结构(IPN)的pH/温度双重敏感性微凝胶D2O分散液,通过差谱技术对不同pH值和温度条件下的红外吸收光谱进行处理,研究微凝胶相转变过程中分子链微环境的变化.结果表明,随着D2O介质的pH值增...     

Comparison of glass transition and interpretation on miscibility in blends of amorphous poly(vinyl methyl ether) with highly crystallizable versus less‐crystallizable polyesters

Various phase behavior of blends of poly(vinyl ether)s with polyesters of two types (highly crystalline and less crystalline with different main‐chains) were examined using differential scanning calorimetry (DSC) and optical microscopy (OM). Effects of varying the main‐chain polarity of the constituent polyesters on the phase behavior of the blends were analyzed. Miscibility in PVME/polyester blends was found only in polyesters with backbone CH₂/CO ratio = 3.5 to 7.0). T_g‐composition relationships for blends of PVME with highly crystalline polyesters (PBA, PHS) were found to differ significantly from those for PVME blends with less‐crystalline polyesters (PTA, PEAz). Crystallinity of highly crystalline polyester constituents in blends caused significant asymmetry in the T_g‐composition relationships, and induced positive deviation of blends' T_g above linearity; on the other hand, blends of PVME with less crystalline polyesters exhibit typical Fox or Gordon‐Taylor types of relationships. The χ parameters for the miscible blends were found to range from ?0.17 to ?0.33, reflecting generally weak interactions. Phase behavior was analyzed and compared among blends of PVME with rapidly crystallizing vs. less‐crystallizing polyesters, respectively. Effects of polyesters' crystallinity and structures on phase behavior of PVME/polyester blends are discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2899–2911, 2007     

Thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide). I. Miscibility and thermal properties

The miscibility and thermal properties of polyethylene oxide(PEO)/oligoester resin (OER) blends and PEO/crosslinked polyester (PER) blends were studied by differential scanning calorimetry (DSC). The effect of quenching process on the crystallization behavior of PEO for these two systems were investigated and discussed in details. It has been found that a single, composition dependent glass transition temperature (T_g) was observed for all the blends, indicating that the two systems are miscible in the amorphous state at overall compositions. From the melting point depression of PEO, the interaction parameter χ₁₂ for PEO/OER blends and that for PEO/PER blends were found to be −1.29 and −2.01, respectively. The negative values of χ₁₂ confirmed that both PEO/OER blends and PEO/PER blends are miscible in the molten state. Quenching process has a greater hindrance on the crystallization of PEO/OER blends than on that of PEO/PER blends. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3161–3168, 1997     

Examination of miscibility at molecular level of poly(hydroxyether of bisphenol A)/poly(N-vinyl pyrrolidone) blends by cross-polarization/magic angle spinning 13C nuclear magnetic resonance spectroscopy

The miscibility of poly(hydroxyether of bisphenol A) (phenoxy) and poly(N-vinyl pyrrolidone) (PVP) was investigated by differential scanning calorimetry (DSC) and high-resolution solid-state nuclear magnetic resonance (NMR) techniques. The DSC studies showed that the phenoxy/PVP blends have a single, composition-dependent glass transition temperature (T_g). The S-shaped T_g-composition curve of the phenoxy/PVP blends was reported, which is indicative of the strong intermolecular hydrogen-bonding interactions. To examine the miscibility of the system at molecular level, high-resolution solid-state ¹³C nuclear magnetic resonance (NMR) technique was employed. Upon adding phenoxy to system, the chemical shift of carbonyl carbon resonance of PVP was observed to shift downfield by 1.6 ppm in the ¹³C cross-polarization (CP)/magic angle spinning (MAS) together with the high-power dipolar decoupling (DD) spectra when the concentration of phenoxy is 90 wt %. The observation was responsible for the formation of intermolecular hydrogen bonding. The proton spin-lattice relaxation time T₁(H) and the proton spin-lattice relaxation time in the rotating frame T_1ρ(H) were measured as a function of the blend composition. The T₁(H) result was in good agreement with the thermal analysis, i.e., the blends are completely homogeneous on the scale of 20 ∼ 30 nm. The six results of T_1ρ(H) further indicated that the blends were homogeneous on the scale of 40 ∼ 50Å. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2291–2300, 1998     

Biodegradable poly(alkylene succinate) blends: Thermal behavior and miscibility study

New binary blends composed of poly(ethylene succinate) and poly(propylene succinate) or poly(ethylene succinate) and poly(butylene succinate) were prepared. Both PESu/PPSu and PESu/PBSu systems belong to semicrystalline/semicrystalline pairs. The miscibility and crystallization behavior was investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarizing light microscopy (PLM). Blends of PESu and PPSu exhibited a single composition dependent glass transition temperature over the entire range of composition, indicating that the system is miscible. The melting point depression of the high melting temperature component, PESu, was analyzed according to the Nishi‐Wang equation. A negative polymer–polymer interaction parameter was obtained, indicating that the blends are thermodynamically miscible in the melt. The two components crystallized sequentially when the blends were cooled rapidly to a low temperature. DSC traces of PESu/PBSu blends after quenching showed two distinct composition dependent glass transition temperatures between those of the neat polymers, showing that the polymers are partially miscible. The amorphous PESu/PBSu blends in the intermediate compositions showed three cold‐crystallization peaks, indicating the influence of mixing. The crystallization rates of PBSu were reduced and those of PESu were increased. WAXD showed reduced crystallinity and peak broadening in the patterns of the blends of intermediate compositions, while no spherulites could be detected by PLM. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 584–597, 2006     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Thermal and dynamic mechanical properties of PES/PPS blends

Blends of poly(ether-sulfone) (PES) and poly(phenylene sulfide) (PPS) with various compositions were prepared using an internal mixer at 290°C and 50 rpm for 10 min. The thermal and dynamic mechanical properties of PES/PPS blends have been investigated by means of DSC and DMA. The blends showed two glass transition temperatures corresponding to PPS-rich and PES-rich phases. Both of them decreased obviously for the blends with PES matrix. On the other hand, T_g of PPS and PES phase decreased a little when PPS is the continuous phase. In the blends quenched from molten state the cold crystallization temperature of PPS was detected in the blends of PES/PPS with mass ratio 50/50 and 60/40. The melting point, crystallization temperature and the crystallinity of blended PPS were nearly unaffected when the mass ratio of PES was less than 60%, however, when the amount of PES is over 60% in the blends, the crystallization of PPS chains was hindered. The thermal and the dynamic mechanical properties of the PPS/PES blends were mainly controlled by the continued phase. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Poly(hydroxyether of phenolphthalein) and its blends with poly(ethylene oxide)

Poly(hydroxyether of phenolphthalein) (PPH) was synthesized through the polycondensation of phenolphthalein with epichlorohydrin. It was characterized by Fourier transform infrared (FTIR) spectroscopy, NMR spectroscopy, and differential scanning calorimetry (DSC). The miscibility of the blends of PPH with poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. DSC showed that the PPH/PEO blends prepared via casting from N,N‐dimethylformamide possessed single, composition‐dependent glass‐transition temperatures. Therefore, the blends were miscible in the amorphous state for all compositions. FTIR studies indicated that there were competitive hydrogen‐bonding interactions with the addition of PEO to the system, which were involved with OH…O?C〈, ? OH…? OH, and ? OH vs ether oxygen atoms of PEO hydrogen bonding, that is both intramolecular and intermolecular, between PPH and PEO). Some of the hydroxyl stretching vibration bands significantly shifted to higher frequencies, whereas others shifted to lower frequencies, and this suggested the formation of hydrogen bonds between the pendant hydroxyls of PPH and ether oxygen atoms of PEO, which were stronger than the intramolecular hydrogen bonding between hydroxyls and carbonyls of PPH. The FTIR spectra in the range of carbonyl stretching vibrations showed that the hydroxyl‐associated carbonyl groups were partially set free because of the presence of the competitive hydrogen‐bonding interactions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 466–475, 2003     

Thermal oxidation of blends of poly(ethylene oxide) and poly(methyl methacrylate)

Thermal oxidation of poly(ethylene oxide) (PEO) and its blends with poly(methyl methacrylate) (PMMA) were studied using oxygen uptake measurements. The rates of oxidation and maximum oxygen uptake contents were reduced as the content of PMMA was increased in the blends. The results were indicative of a stabilizing effect by PMMA on the oxidation of PEO. The oxidation reaction at 140°C was stopped at various stages and PMMA was separated from PEO and its molecular weights were measured by gel permeation chromatography (GPC). The decrease in the number-average molecular weight of PMMA was larger as the content of PEO increased in the blends. The visual appearance of the films suggested that phase separation did not occur after thermal oxidation. The activation energy for the rates of oxidation in the blends was slightly increased compared to pure PEO. © 1992 John Wiley & Sons, Inc.     

Thermal Dehydration and Miscibility of PHEMA/PMAA Blends

Miscibility and dehydration of poly(2-hydroxyethyl methacrylate) and poly(methacrylic acid) (PHEMA/PMAA) blends were investigated by temperature modulated DSC (TMDSC), TG and solid-state ¹³C NMR methods. TMDSC spectra and ¹H spin-relaxation times showed that the blends are homogeneous on a scale of 5-10 nm for all compositions. From TG and ¹³C NMR, we elucidated that the mass loss of the blends at 300°C is ascribed to the dehydration between the hydroxyl group of PHEMA and the carboxyl group of PMAA. This revised version was published online in August 2006 with corrections to the Cover Date.     

Miscibility and thermal properties of melt‐mixed poly(trimethylene terephthalate)/amorphous copolyester blends

This work examined the miscibility, crystallization kinetics, and melting behavior of melt‐mixed poly(trimethylene terephthalate) (PTT)/poly(ethylene‐co‐cyclohexane 1,4‐dimethanol terephthalate) (PETG) blends. Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction techniques were used to approach the goals. The single composition‐dependent glass‐transition temperatures of the blends and the equilibrium melting temperature (T) depression of PTT in the blends indicated the miscible characteristic of the blend system at all compositions. T of pure PTT, determined with a conventional extrapolative method, was 525.8 K. Furthermore, the Flory–Huggins interaction parameter was estimated to be ?0.38. The dynamic and isothermal crystallization abilities of PTT were hindered by the incorporation of PETG. A complex melting behavior was observed for pure PTT and its blends. The observed complex melting behavior resulted mainly from the recrystallization and/or reorganization of the originally formed crystals during the heating scans. For the samples crystallized under the same conditions, the degree of recrystallization and/or reorganization declined with increasing PETG contents in the blends. The preliminary results obtained from the DSC experiments suggested that untraceable interchange reactions occurred in the studied blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2264–2274, 2003     

Thermo and pH Dual-Responsive Micelles of N-phthaloylchitosan-g-Poly(N-isopropylacrylamide) and Poly(acrylic acid-co-tert-butyl acrylate) for Drug Delivery

A novel amphiphilic copolymer N-phthaloylchitosan graft poly(N-isopropylacrylamide) and poly(acrylic acid-co-tert-butyl acrylate) (PHCS-g-PNIPAAm&P(AA-co-tBA)) was synthesized. The graft copolymer could form micelles in aqueous medium, and the critical micelle concentration (CMC) of the copolymer was 7.5 × 10^{? 3}mg/mL. The lower critical solution temperature (LCST) of the micelles was measured to be 30°C. Transmission electron microscopy (TEM) image showed that the micelles exhibited a regular spherical shape, and the mean diameter of the micelles was 94.1 ± 0.8 nm as determined by dynamic light scattering (DLS). The potential usefulness of the micelles as drug delivery systems was investigated using anti-inflammation drug prednisone acetate as the model. The drug loading capacity of the micelles was measured to be 22.86 wt%, and the DLS results showed that the mean diameter of the drug-loaded micelles was 133.3 ± 2.4 nm. In vitro drug release studies indicated that the micelles exhibited thermo and pH dual-responsive release profiles.     

The synthesis of a precursor of polybenzimidazole (PBI) and blends with polyamic acid (PAA)

The precursor of polybenzimidazole (PBI), poly(3,3′-diamino-4,4′-benzidine isophthalamide) (PDABI), was synthesized from poly(3,3′-dinitro-4,4′-benzidine isophthalamide) (PDNBI) by reduction. With increasing temperature, the NH₂ moiety which was protected by SnCl₅^?1 could cyclize and form PBI. Blends with polyamic acid (LaRC-TPI) were prepared. Clear blend films were prepared at up to 400°C. The IR spectra displayed shifts in the NH stretching band, thereby providing evidence for specific interactions related to the miscibility of their cured blends. © 1993 John Wiley & Sons, Inc.     

Miscibility and crystallization behavior of solution-blended PEEK/PI blends

Miscibility and crystallization behavior of solution-blended poly(ether ether ketone)/polyimide (PEEK/PI) blends were investigated by using DSC, optical microscopy and SAXS methods. Two kinds of PIs, YS-30 and PEI-E, which consist of the same diamine but different dianhydrides, were used in this work. The experimental results show that blends of PEEK/YS-30 are miscible over the entire composition range, as all the blends of different compositions exhibit a single glass transition temperature. The crystallization of PEEK was hindered by YS-30 in PEEK/YS-30 blends, of which the dominant morphology is interlamellar. On the other hand, blends of PEEK/PEI-E are immiscible, and the effect of PEI-E on the crystallization behavior of PEEK is weak. The crystallinity of PEEK in the isothermally crystallized PEEK/YS-30 blend specimens decreases with the increase in PI content. But the crystallinity of PEEK in the annealed samples almost keeps unchanged and reaches its maximum value, which is more than 50%. The spherulitic texture of the blends depends on both the blend composition and the molecular structure of the PIs used. The more PI added, the more imperfect the crystalline structure of PEEK. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2267–2274, 1998     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Application of Crosslinked Ionic Poly(Vinyl Alcohol) Nanogel as Adsorbents for Water Treatment

Core-shell smart ionic nanogels based on poly(vinyl alcohol) (PVA) core and poly(N-isopropylacrylamide/acrylic acid) p(NIPAm-AAc) shell particles were successfully synthesized through a one-step surfactant-free emulsion polymerization method (SFEP). Different mole ratios of p(NIPAm-AAc) shells were synthesized. The morphologies of PVA/p(NIPAm-AAc) nanogels were investigated by transmission electron microscope (TEM). The data showed the formation of spherical nanoparticles and well-defined core-shell nanogels. PVA/p(NIPAm-AAc) core-shell nanogels were applied as a novel polymeric adsorbent to remove heavy metal pollutants from aqueous solution. Copper(II) (Cu²⁺) ions were selected as the target pollutant to evaluate these nanoparticles’ adsorption capability. The influence of the uptake conditions such as pH, weight ratio of nanoparticles, time, initial feed concentration, and adsorption temperature on the metal ion binding capacity of nanogels was also tested. Adsorption equilibrium data were calculated according to Langmuir and Freundlich isotherms. It was found that the sorption of Cu²⁺ was better suited to the Freundlich adsorption model than the Langmuir adsorption model. Also, the selectivity of the nanogels toward the different metal ions such lead (Pb²⁺) and cadmium (Cd²⁺) were tested. The maximum of Cu²⁺ ions adsorbed on to PVA/p(NIPAm-AAc) core-shell nanogels adsorbent was 94 mg/g obtained under simple and fast experimental conditions, indicating these nanogels can be used as effective and practical polymeric adsorbents.