Characteristics of R-123 two-phase flow through micro-scale short tube orifice for design of a small cooling system

We present a new discharge coefficient correction method for the orifice equation for R-123 two-phase flows. In this method, an evaporator is mounted after the orifice as a vapor refrigeration cycle, and the evaporator is used to measure the quality of downstream flow through the orifice. Quality is estimated from the measured temperature and pressure of the evaporator inlet and outlet, respectively, instead of by direct measurement of quality. The condition of upstream flow of the orifice is the liquid state at 3 bar and 60 °C. The liquid flow is changed to two-phase flow after passing through the orifice. Orifice diameters of 300, 350, 400, and 450 μm are used for the experiment, and the results are analyzed. Experiments are conducted for various conditions of flow rate between 20 and 70 ml/min and for cooling loads of 60, 80, and 100 W. The results show that the quality of flow downstream from the orifice can be calculated using the enthalpy difference between the inlet and outlet of the evaporator. An equation to determine the discharge coefficient is formulated as a function of quality. We expect that these results can be used to help design a small cooling system.     

Choked flow mechanism of HFC-134a flowing through short-tube orifices

This paper is a continuation of the author’s previous work. New experimental data on the occurrence of choked flow phenomenon and mass flow rate of HFC-134a inside short-tube orifices under choked flow condition are presented. Short-tube orifices diameters ranging from 0.406 mm to 0.686 mm with lengths ranging from 1 mm to 3 mm which can be applied to a miniature vapour-compression refrigeration system are examined. The experimental results indicated that the occurrence of choked flow phenomena inside short-tube orifices is different from that obtained from short-tube orifice diameters of greater than 1 mm, which are typically used in air-conditioner. The beginning of choked flow is dependent on the downstream pressure, degree of subcooling, and length-to-diameter ratio. Under choked flow condition, the mass flow rate is greatly varied with the short-tube orifice dimension, but it is slightly affected by the operating conditions. A correlation of mass flow rate through short-tube orifices is proposed in terms of the dimensionless parameters. The predicted results show good agreement with experimental data with a mean deviation of 4.69%.     

Hydrodynamics of two-phase flow in vertical up and down-flow across a horizontal tube bundle

Flow patterns, void fraction and friction pressure drop measurements were made for an adiabatic, vertical up-and-down, two-phase flow of air–water mixtures across a horizontal in-line, 5×20 tube bundle with a pitch-to-diameter ratio of 1.28. The flow patterns in the cross-flow zones were obtained and flow pattern maps were constructed. The data of average void fraction were less than the values predicted by a homogenous flow model and showed a strong mass velocity effect, but were well-correlated in terms of the Martinelli parameter X_tt and liquid-only Froude number Fr_LO. The two-phase friction multiplier data could be well-correlated with the Martinelli parameter.     

An experimental study of drag on a single tube and on a tube in an array under two-phase cross flow

In this work, the drag coefficient and the void fraction around a tube subjected to two-phase cross flow were studied for a single tube and for a tube placed in an array. The drag coefficients were determined by measuring the pressure distribution around the perimeter of the tube. Single tube drag data were taken when the tube was held both rigidly and flexibly. The test tube was made of acrylic and was 2.2 cm in diameter and 20 cm in length. In the experiments, liquid Reynolds number ranged from 430 to 21,900 for the single tube and liquid gap Reynolds number ranged from 32,900 and 61,600 for the tube placed in a triangular array. Free stream void fraction was varied from 0 to 0.4. At low Reynolds numbers, the ratio of two-phase to single-phase drag coefficient is found to be a strong function of εGr/Re2. However, at high Reynolds numbers only void fraction is the important parameter. Empirical correlations have been developed for the ratio of two-phase drag on a single tube and on a tube placed in an array.     

Critical flow in a chemically reacting two-phase multicomponent mixture

A model that describes the critical flow of chemically reacting, two-phase, multicomponent mixtures in channels of constant cross section is discussed. As a consequence of an assumed interphase thermal and mechanical equilibrium the applicability of the model is restricted to situations where one phase is intimately mixed with the other, such that choking is determined by the sound speed in the homogeneous mixture. It is shown that under certain conditions the highly non-linear temperature dependency of the reaction rate promotes the possibility of a multiplicity of steady state solutions to the problem.     

Steady-state two-phase flow through planar and nonplanar model porous media

Transport in Porous Media - A comparative experimental study of ‘steady-state’ two-phase flow in two types of model porous media is made to determine the effects of nonplanarity on the...     

An analytic solution of dense two-phase flow in a vertical pipeline

According to a mathematical model for dense two-phase flows presented in theprevious paper,a dense two-phase flow in a vertical pipeline is analytically solved,and theanalytic expressions of velocity of each continuous phase and dispersed phase arerespectively derived The results show that when the drag force between two phases dependslinearly on their relative velocity,the relative velocity profile in the pipeline coincides withDarcy’s law except for the thin layer region near the pipeline wall,and that the theoreticalassumptions in the dense two-phase flow theory mentioned are reasonable.     

Visual observation of two-phase flow pattern of R-22, R-134a, and R-407C in a 6.5-mm smooth tube

Two-phase flow pattern and friction characteristics for R-22, R-134a, and R-407C inside a 6.5 mm smooth tube are reported in this study. The range of mass flux is between 50 and 700 kg/(m² s). The experimental data show that the two-phase friction multipliers are strongly related to the flow pattern. For a stratified, wavy flow pattern a mass-flux dependence of the multipliers is seen. The flow pattern transition for the mixture refrigerant shows a considerable delay, compared with that of pure refrigerant.     

Gas-particle two-phase turbulent flow in a vertical duct

Two-phase gas-phase turbulent flows at various loadings between the two vertical parallel plates are analyzed. A thermodynamically consistent turbulent two-phase flow model that accounts for the phase fluctuation energy transport and interaction is used. The governing equation of the gas-phase is upgraded to a two-equation low Reynolds number turbulence closure model that can be integrated directly to the wall. A no-slip boundary condition for the gas-phase and slip-boundary condition for the particulate phase are used. The computational model is first applied to dilute gas-particle turbulent flow between two parallel vertical walls. The predicted mean velocity and turbulence intensity profiles are compared with the experimental data of Tsuji et al. (1984) for vertical pipe flows, and good agreement is observed. Examples of additional flow properties such as the phasic fluctuation energy, phasic fluctuation energy production and dissipation, as well as interaction momentum and energy supply terms are also presented and discussed.

Applications to the relatively dense gas-particle turbulent flows in a vertical channel are also studied. The model predictions are compared with the experimental data of Miller & Gidaspow and reasonable agreement is observed. It is shown that flow behavior is strongly affected by the phasic fluctuation energy, and the momentum and energy transfer between the particulate and the fluid constituents.     

Dynamic fluid flow behaviour of a tank draining through a vertical tube

This paper describes the unsteady draining of a sealed tank partially filled with water. The water discharges via a vertical tube into an open tank at atmospheric conditions. The air inflow, compensating for the volume of the discharged liquid, enters the system in an oscillatory manner, much like the “gulping” seen in an upended beer bottle. A mathematical model, based closly on that derived by Dougall & Kathiresan [Chem. Engng Commun. 8, 289–304 (1981)], has been applied to predict the pressure fluctuations in the closed tank. The rate of water discharge from the tank has been predicted and gives a much closer agreement with experimental results than a prediction based on a steady counter-current flooding limitation approach. A drift flux model has been used to describe the two-phase flow effect in the tube and the Wallis flooding criterion has been modified for use in the slug flow regime to describe the boundary conditions at the bottom of the tube. The pressure fluctuations in the sealed tank have been measured and compared with results obtained from the mathematical prediction for a variety of tube diameters.     

Adiabatic and diabatic two-phase venting flow in a microchannel

The growth and advection of the vapor phase in two-phase microchannel heat exchangers increase the system pressure and cause flow instabilities. One solution is to locally vent the vapor formed by capping the microchannels with a porous, hydrophobic membrane. In this paper we visualize this venting process in a single 124 μm by 98 μm copper microchannel with a 65 μm thick, 220 nm pore diameter hydrophobic Teflon membrane wall to determine the impact of varying flow conditions on the flow structures and venting process during adiabatic and diabatic operation. We characterize liquid velocities of 0.14, 0.36 and 0.65 m/s with superficial air velocities varying from 0.3 to 8 m/s. Wavy-stratified and stratified flow dominated low liquid velocities while annular type flows dominated at the higher velocities. Gas/vapor venting can be improved by increasing the venting area, increasing the trans-membrane pressure or using thinner, high permeability membranes. Diabatic experiments with mass flux velocities of 140 and 340 kg/s/m² and exit qualities up to 20% found that stratified type flows dominate at lower mass fluxes while churn-annular flow became more prevalent at the higher mass-flux and quality. The diabatic flow regimes are believed to significantly influence the pressure-drop and heat transfer coefficient in vapor venting heat exchangers.     

A stream tube model for miscible flow

A simple theoretical model is described for deriving a 1-dimensional equation for the spreading of a tracer in a steady flow at the field scale. The originality of the model is to use a stochastic appoach not in the 3-dimensional space but in the 1-D space of the stream tubes. The simplicity of calculation comes from the local relationship between permeability and velocity in a 1-D flow. The spreading of a tracer front is due to local variations in the cross-sectional area of the stream tubes, which induces randomness in travel time. The derived transport equation is averaged in the main flow direction. It differs from the standard dispersion equation. The roles of time and space variables are exchanged. This result can be explained by using the statistical theory of Continuous Time Random Walk instead of a standard Random Walk. However, the two equations are very close, since their solutions have the same first and second moments. Dispersivity is found to be equal to the product of the correlation length by the variance of the logarithm of permeability, a result similar to Gelhar's macrodispersion.Nomenclature A total cross-section area of the sample - C (resident) concentration of tracer - D,D ^* dispersion coefficient - F flux of tracer - G probability distribution function for permeability in the stream-tube segments - I tracer intensity (mass crossing a surface per unit time) - K permeability - L length of the medium - M number of stream tubes in the medium - N number of segments along a stream tube - P pressure - Q total flow rate in the sample - a length of an elementary stream-tube segment - g probability distribution function for permeability in the space - i, j indices, tube numbers - q flow rate in each stream tube - s variable cross-section area of a stream tube - t, t time - u front velocity - x space variable in the flow direction - small local variation in time - , _t longitudinal, transverse dispersivity - porosity of the porous medium - correlation length in the permeability field - viscosity of the fluid - time for filling an elementary stream tube segment - standard deviation of a stochastic variable - probability distribution of arrival times (Gaussian)     

A separated flow model for predicting two-phase pressure drop and evaporative heat transfer for vertical annular flow

A separated flow model has been developed that is applicable to vertical annular two-phase flow in the purely convective heat transfer regime. Conservation of mass, momentum, and energy are used to solve for the liquid film thickness, pressure drop, and heat transfer coefficient. Closure relationships are specified for the interfacial friction factor, liquid film eddy-viscosity, turbulent Prandtl number, and entrainment rate. Although separated flow models have been reported previously, their use has been limited, because they were tested over a limited range of flow and thermal conditions. The unique feature of this model is that it has been tested and calibrated against a vast array of two-phase pressure drop and heat transfer data, which include upflow, downflow, and microgravity flow conditions. The agreements between the measured and predicted pressure drops and heat transfer coefficients are, on average, better or comparable to the most reliable empirical correlations. This separated flow model is demonstrated to be a reliable and practical predictive tool for computing two-phase pressure drop and heat transfer rates. All of the datasets have been obtained from the open literature.     

Turbulent friction factor for two-phase: air-viscoelastic flows through a horizontal tube

The fully developed two-phase turbulent isothermal Fanning friction factors for air-viscoelastic fluid flows through a horizontal tube were measured experimentally. The viscoelastic fluids studied were aqueous solutions of polyacrylamide (100, 200, and 500 ppm by weight). Over the range of the apparent Reynolds number (Re_e) from 10,000 to 100,000, the homogeneous model was found to be accurate enough for engineering prediction of turbulent friction factor for air-viscoelastic flows through horizontal tubes. A new correlation for the turbulent friction factor of airlriscoelastic plug flow is proposed.     

Experimental determination of the flow transport coefficients in the coupled equations of two-phase flow in porous media

The transport coefficients in the coupled equations of two-phase flow are defined if the pressure gradient in one of the two flowing fluids is equal to zero. This definition has been used in experiments with oil and water in a sandpack and the four transport coefficients have been measured over wide water saturation ranges. The values of the cross coefficients were found to be significant as they ranged from 10 to 35% of the value of the effective permeability to water and from 5 to 15% of the effective permeability to oil, respectively.     

大长径比点火管高密实火药床点传火过程两相流的数值模拟

设计了某中心点火管,完成了该点火管的点传火实验,针对该点火管长径比大、装填密度高的特点,建立了点火管内气固两相流动和燃烧过程的一维两相流模型,并进行了数值模拟。计算结果与实验结果良好符合,说明计算模型能够准确描述点火管内的实际物理化学过程,计算程序参数取值合理,该计算程序可为此类点火管各种结构尺寸及装填条件下的点传火性能分析及优化计算提供充分的理论依据和方法。并且,根据计算结果初步分析了该结构及装填条件下点火管的点传火性能,为下阶段工程优化设计提供参考     

Finite element solution of multi-dimensional two-phase flow through porous media with arbitrary heating conditions

Mechanistic models for flow regime transitions and drag forces proposed in an earlier work are employed to predict two-phase flow characteristics in multi-dimensional porous layers. The numerical scheme calls for elimination of velocities in favor of pressure and void fraction. The momentum equations for vapor and liquid then can be reduced to a system of two partial differential equations (PDEs) which must be solved simultaneously for pressure and void fraction.

Solutions are obtained both in two-dimensional cartesian and in axi-symmetric coordinate systems. The porous layers in both cases are composed of regions with different permeabilities. The finite element method is employed by casting the PDEs in their equivalent variational forms. Two classes of boundary conditions (specified pressure and specified fluid fluxes) can be incorporated in the solution. Volumetric heating can be included as a source term. The numerical procedure is thus suitable for a wide variety of geometry and heating conditions. Numerical solutions are also compared with available experimental data.     

The study on three-dimensional mathematical model of river bed erosion for water-sediment two-phase flow

Based on the tensor analysis of water-sediment two-phase flow, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turbulent flow. Furthermore, corresponding boundary conditions are also presented in connection with the composition and movement of non-uniform bed material. The theoretical results are applied to the calculation of the float open caisson in the construction period and good results are obtained.     

Analytical solution for laminar flow through leaky tube

The laminar flow through a leaky tube is investigated, and the momentum and conservation of energy equations are solved analytically. By using the Hagen-Poiseuille velocity profile and defining unknown functions for the axial and radial velocity components, the pressure and mass transfer equations are obtained, and their profiles are plotted according to different parameters. The results indicate that the axial velocity, the radial velocity, the mass transfer parameter, and the pressure in the tube decrease as the fluid moves along the tube.     

Effect of the magnetic field on the pulsatile flow through a rigid tube

I.IntroductionThefunctionofanaPbliedmagneticfield\onhumanbodieshasbeenknownandservedasakindofthemedicaltreatmentforalongtime.ThemagneticstoneusedasamedicineisrdeordedinShennongMaterlbMedica,'which.isthefirstChinesemedicinebookandwaswrittenin200A.D..ItwasalsorecordedtyancientGreecethatholdingmagneticstQnesinhandsandfeetcouldrelievethepainandspasml'l.However,beinglimitedbythelevelQfproductionandmedicaltreatmentsatthattime,themagnetictreatmentwasmainlyusedforlocallydephlogisticating,relievin…