Electrochemical bisphenol A sensor based on N-doped graphene sheets

Bisphenol A (BPA), which could disrupt endocrine system and cause cancer, has been considered as an endocrine disruptor. Therefore, it is very important and necessary to develop a sensitive and selective method for detection of BPA. Herein, nitrogen-doped graphene sheets (N-GS) and chitosan (CS) were used to prepare electrochemical BPA sensor. Compared with graphene, N-GS has favorable electron transfer ability and electrocatalytic property, which could enhance the response signal towards BPA. CS also exhibits excellent film forming ability and improves the electrochemical behavior of N-GS modified electrode. The sensor exhibits a sensitive response to BPA in the range of 1.0 × 10⁻⁸–1.3 × 10⁻⁶ mol L⁻¹ with a low detection limit of 5.0 × 10⁻⁹ mol L⁻¹ under the optimal conditions. Finally, this proposed sensor was successfully employed to determine BPA in water samples with satisfactory results.     

Mesoporous silica-based electrochemical sensor for sensitive determination of environmental hormone bisphenol A

Bisphenol A (BPA) is an emerging contaminant with severe toxic effects such as disrupting endocrine system or causing cancer, therefore, developing sensitive and selective sensor for BPA is very important and interesting. Herein, MCM-41, a kind of mesoporous silica, was synthesized and then used to prepare an electrochemical sensor for BPA. For better comparison, carbon nanotubes, activated carbon, silica gel and graphite were also employed to prepare electrochemical sensor for BPA. The electrochemical behaviors of BPA at different electrochemical sensors were investigated. Compared with other sensors, the MCM-41 sensor greatly enhances the response signal of BPA due to the large active surface area and high accumulation efficiency. The effects of pH value, accumulation time and sensor composition were examined. The linear range is from 2.2 × 10⁻⁷ to 8.8 × 10⁻⁶ mol L⁻¹, and the limit of detection is evaluated to be 3.8 × 10⁻⁸ mol L⁻¹. Finally, the MCM-41 sensor was successfully employed to determine BPA in water samples.     

A highly sensitive electrochemical sensor for simultaneous determination of hydroquinone and bisphenol A based on the ultrafine Pd nanoparticle@TiO2 functionalized SiC

A titanium dioxide–silicon carbide nanohybrid (TiO₂–SiC) with enhanced electrochemical performance was successfully prepared through a facile generic in situ growth strategy. Monodispersed ultrafine palladium nanoparticles (Pd NPs) with a uniform size of ∼2.3 nm were successfully obtained on the TiO₂–SiC surface via a chemical reduction method. The Pd-loaded TiO₂–SiC nanohybrid (Pd@TiO₂–SiC) was characterized by transmission electron microscopy and X-ray diffractometry. A method for the simultaneous electrochemical determination of hydroquinone (HQ) and bisphenol A (BPA) using a Pd@TiO₂–SiC nanocomposite-modified glassy carbon electrode was established. Utilizing the favorable properties of Pd NPs, the Pd@TiO₂–SiC nanohybrid-modified glassy carbon electrode exhibited electrochemical performance superior to those of TiO₂–SiC and SiC. Differential pulse voltammetry was successfully used to simultaneously quantify HQ and BPA within the concentration range of 0.01–200 μM under optimal conditions. The detection limits (S/N = 3) of the Pd@TiO₂–SiC nanohybrid electrode for HQ and BPA were 5.5 and 4.3 nM, respectively. The selectivity of the electrochemical sensor was improved by introducing 10% ethanol to the buffer medium. The practical application of the modified electrode was demonstrated by the simultaneous detection of HQ and BPA in tap water and wastewater samples. The simple and straightforward strategy presented in this paper are important for the facile fabrication of ultrafine metal NPs@metal oxide–SiC hybrids with high electrochemical performance and catalytic activity.     

Electrochemical recognition and trace-level detection of bactericide carbendazim using carboxylic group functionalized poly(3,4-ethylenedioxythiophene) mimic electrode

The electrochemical recognition and trace-level detection of bactericide carbendazim (MBC) in paddy water and commercial juice were realized using carboxylic group functionalized poly(3,4-ethylenedioxythiophene) (PC4-EDOT-COOH) film electrode. PC4-EDOT-COOH film was prepared by one step, low-cost, and green electrosynthesis in aqueous microemulsion system and characterized by FT-IR, cyclic voltammetry, UV–vis and SEM. In comparison with poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(hydroxymethylated-3,4-ethylenedioxylthiophene) (PEDTM), PC4-EDOT-COOH exhibited the best electrochemical recognition towards MBC and the recognition mechanism was proved by quantitative calculation. Sensing parameters such as pH values, accumulation potential, accumulation time, supporting electrolyte, and scan rate on the current response of MBC were discussed. In addition, the sensor can be applied to quantification of MBC in the concentration range of 0.012–0.35 μM with a low detection limit of 3.5 nM (S/N = 3). Moreover, PC4-EDOT-COOH film electrode showed good stability, high selectivity, and satisfactory anti-interference ability. Satisfactory results indicated that PC4-EDOT-COOH film is a promising sensing platform for the trace-level analysis of bactericide residue carbendazim in agricultural crops and environment.     

Two-dimensional TiO2 (001) nanosheets as an effective photo-assisted recyclable sensor for the electrochemical detection of bisphenol A

Electrochemical detection is an efficient method for the detection of Bisphenol A (BPA). Herein, a sensitive photo-electrochemical sensor based on two-dimensional (2D) TiO₂ (001) nanosheets was fabricated and then used for BPA electrochemical detection. Upon light irradiation, the 2D TiO₂ (001) nanosheets electrode provided a lower detection limit of BPA detection compared with an ambient electrochemical determination. The low detection limit is ∼5.37 nmol/L (S/N = 3). Furthermore, profiting from the photoelectric characteristics, the 2D TiO₂ (001) nanosheets electrode exhibits a nice regeneration property. After 45 min of light irradiation, the electrochemical signal was regenerated from 14.7% to 82.9% of the original signal at the 6^th cycle. This is attributed to the non-selective OH mediation produced by the 2D TiO₂ (001) nanosheets mineralizing anodic polymeric products and resuming surface reactive sites. This investigation indicates that photo-assistance is an efficient method to improve the electrochemical sensor for detecting BPA in water environments.     

HYDROGEN-BONDING INDUCED CHANGE OF CRYSTALLIZATION BEHAVIOR OF POLY（BUTYLENE SUCCINATE） IN ITS MIXTURES WITH BISPHENOL A

In the present work, the blend of poly（butylene succinate） （PBS） and bisphenol A （BPA） was prepared by solution mixing, and the intermolecular interactions between the two components were characterized by a combination of nuclear magnetic resonance （NMR） and Fourier transform infrared spectroscopy （FTIR）. The results showed that intermolecular hydrogen-bonding forms between the carbonyl group of PBS and phenol hydroxyl of BPA. With the increase of BPA content, more hydrogen bonds were formed. The effect of hydrogen bonding on the crystallization behavior of PBS was investigated by differential scanning calorimetry （DSC） and polarized optical microscopy （POM）. The results showed that the overall isothermal crystallization kinetics and the spherulite growth rate of PBS decrease with the increase of BPA content, while the PBS spherulite size increases with BPA content.     

Electro-active silver oxide nanocubes for label free direct sensing of bisphenol A to assure water quality

This research, for the first time, demonstrates a direct electrochemical detection of bisphenol A (BPA) using silver oxide (Ag₂O) nanocubes (NCs) modified platinum electrode. The Ag₂O NCs, size ranging from 60 to 100 nm utilized in this research as a smart electro-active sensing platform were pure and synthesized using a cost-effective, affordable, and facile chemical route. The Ag₂O NCs modified electrochemical sensor exhibited a low limit of detection (LOD) as 20 nmol dm^?3, high sensitivity as 95 μA (μmol dm^?3)^?1 cm^?2, and linear dynamic range (LDR) varies from 80 nmol dm^?3- 4.8 μmol dm^?3. This sensor also showed good selectivity, reproducibility, and reusability for BPA detection. The practical application of developed sensor was also tested using real water samples. The outcomes of this research suggested that Ag₂O NCs based sensor can be useful for effective and efficient electrochemical BPA sensing in both real and lab samples.     

基于还原石墨烯/纳米银复合材料的电化学传感器测定双酚A

石墨烯特有的褶皱层状结构以及银纳米粒子良好的催化性能,使其在电化学方面具有良好的应用潜能.本研究以柠檬酸钠为还原剂,通过水热反应原位制备出还原石墨烯/纳米银复合材料(rGO/AgNPs),用于修饰玻碳电极,研究了双酚A的电化学行为.循环伏安法(CV)和方波伏安法(SWV)的实验结果表明,双酚A可以在rGO/AgNPs修饰电极表面发生快速的氧化还原反应,基于此实现了对双酚A的高灵敏检测.在最优条件下,双酚A的氧化峰电流与其浓度在0.1~40.0μmol/L范围内呈良好的线性关系(r2=0.996),检出限为50.7 nmol/L(S/N=3).将其用于实际环境和塑料样品中双酚A的检测,回收率为91.7%~102.9%.     

Electrochemical Sensor Based on Thioether Oligomer Poly(N‐vinylpyrrolidone)‐modified Gold Electrode for Bisphenol A Detection

Presently, bisphenol A (BPA) has been added to the list of substances of very high concern as endocrine disruptors. According to the literature, exposure to bisphenol A even at low doses may result in adverse health effects. In this study, electrochemical sensor of Bisphenol A based on thioether DDT‐Poly(N‐vinylpyrrolidone) oligomer has been developed. The thioether oligomer, which is capable of recognizing BPA, was prepared and used for gold electrode modification. The characterization of the modified gold electrode and the synthesized thioether oligomer were carried out by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), atomic force microscopy (AFM), Fourier‐transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (¹H NMR) and Size exclusion chromatography (SEC). Obtained results indicate that the modified electrode shows good electrochemical activity, good sensitivity and reproducibility for BPA detection. It exhibited a good linear relationship ranging from 1 to 20 pg/mL, and the detection limit was found to be 1.9 pg/mL at S/N=3. Several interfering species such as hydroquinone, phenol and resorcinol were used and their behaviors on the modified gold electrode were investigated.     

POMs as Active Center for Sensitively Electrochemical Detection of Bisphenol A and Acetaminophen

A new type of electrochemical sensor based on multi-walled carbon nanotubes(MWCNTs), K2H4SiW11CuO39-6H2O(SiW11Cu) and gold nanoparticles(AuNPs) was prepared for the simultaneous detection of bisphenol A and acetaminophen. Differential pulse voltammetry(DPV), cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were used for electrochemical characterization, and Fourier transfonn infrared spectroscopy(FTIR) was used to characterize the structure of polyoxometalates. Electrochemical experimental results show that the composite modified electrodes have good electrochemical activity as well as current response values of bisphenol A and acetaminophen when pH=7.0. At the same time, the modified electrode exhibits good stability and reproduction, and has good anti-interference ability to other substances. In practical application, the sensor obtained satisfactory results.     

A disposable electrochemical sensor for the determination of indole-3-acetic acid based on poly(safranine T)-reduced graphene oxide nanocomposite

A disposable electrochemical sensor for the determination of indole-3-acetic acid (IAA) based on nanocomposites of reduced graphene oxide (rGO) and poly(safranine T) (PST) was reported. The sensor was prepared by coating a rGO film on a pre-anodized graphite electrode (AGE) through dipping-drying and electrodepositing a uniform PST layer on the rGO film. Scanning electron microscopic (SEM) and infrared spectroscopic (IR) characterizations indicated that PST-rGO formed a rough and crumpled composite film on AGE, which exhibited high sensitive response for the oxidation of IAA with 147-fold enhancement of the current signal compared with bare AGE. The voltammetric current has a good linear relationship with IAA concentration in the range 1.0 × 10⁻⁷-7.0 × 10⁻⁶ M, with a low detection limit of 5.0 × 10⁻⁸ M. This sensor has been applied to the determination of IAA in the extract samples of several plant leaves and the recoveries varied in the range of 97.71-103.43%.     

A simple and sensitive portable system for a rapid evaluation of bisphenol A contamination in potable and environmental waters using a mesoporous silica-modified carbon paste electrode

In this work, two ordered mesoporous silicas (HMS and SBA-15) were prepared and incorporated into carbon paste electrodes (CPEs) to obtain mesostructured sensors for a rapid determination of bisphenol A (BPA) in waters by voltammetric techniques. The materials were characterised by nitrogen adsorption-desorption measurements, transmission electron microscopy and scanning electron microscopy. The electrochemical properties of the modified carbon paste electrodes were studied by differential pulse voltammetry (DPV) and cyclic voltammetry (CV). Results showed that the sensor modified with HMS (HMS-CPE) exhibited strong adsorption activity toward the oxidation of BPA, with a well-defined voltammetric peak at +0.6 V. Moreover, the HMS-CPE exhibited a wider linearity range, from 0.44 to 3.5 μM BPA, with a detection limit of 61 nM (S/N = 3) and good reproducibility by DPV. The enhanced performance of the HMS-CPE could be attributed to its high surface area, with a 3 D wormhole-like channel structure that favoured an excellent accessibility, high adsorption capacity and faster adsorption rate of BPA. This novel sensor was coupled to a portable system and successfully applied for a rapid determination of BPA in tap, mineral, well and river water samples with good recovery, ranging from 98 ± 12 to 103 ± 7%.     

An Electrochemical Sensor Based on Nitrogen‐doped Carbon Nanofiber for Bisphenol A Determination

In this paper, bisphenol A was determined by electrochemical method at a nitrogen‐doped carbon nanofiber modified carbon paste electrode (NCNF/CPE) with high sensitivity and good selectivity. NCNF was obtained by a simple electrospinning followed by carbonization procedure, in which polyacrylonitrile (PAN) as precursor and nitrogen doping was realized by re‐utilizing the tail gas that produced in the thermal pretreatment process. Good reproducibility and high stability were obtained for BPA detection at NCNF modified CPE. Current response plotted with BPA concentration was linear in the range of 0.1–60 μM with LOD of 0.05 μM. The proposed electrochemical sensor was employed for BPA determination with satisfactory recoveries for real water samples, indicating the practical applicability of NCNF/CPE.     

Acetylene black paste electrode modified with molecularly imprinted polymers/graphene for the determination of bisphenol A

A novel nanocomposite of molecularly imprinted polymers and graphene sheets was fabricated and used to obtain a highly conductive acetylene black paste electrode with high conductivity for the detection of bisphenol A. The two‐dimensional structure and the chemical functionality of graphene provide an excellent surface for the enhancement of the sensitivity of the electrochemical sensor and the specificity of molecularly imprinted polymers to improve detection of bisphenol A. The synergistic effect between graphene and molecularly imprinted polymers confers the nanocomposite with superior conductivity, broadened effective surface area and outstanding electrochemical performance. Factors affecting the performance of the imprinted sensor such as molecularly imprinted polymers concentration, foster time and scan rate are discussed. The sensor successfully detects bisphenol A with a wide linear range of 3.21 × 10^?10 to 2.8 × 10^?1 g/L (R = 0.995) and a detection limit of 9.63 × 10^?11g/L. The fabricated sensor also possessed high selectivity and stability and exhibits potential for environmental detection of contaminants and food safety inspection.     

Selective determination of bisphenol A (BPA) in water by a reversible fluorescence sensor using pyrene/dimethyl β-cyclodextrin complex

A bifurcated optical fiber chemical sensor for continuous monitoring of bisphenol A (BPA) has been proposed based on the fluorescence quenching (λ_ex/λ_em = 286/390 nm) of pyrene/dimethyl β-cyclodextrin (HDM-β-CD) supramolecular complex immobilized in a plasticized poly(vinyl chloride) (PVC) membrane, in which pyrene served as a sensitive fluorescence indicator probe. The decrease of the fluorescence intensity of pyrene/HDM-β-CD complex upon the addition of BPA was attributed to the displacement of pyrene by BPA, which has been utilized as the basis of the fabrication of a BPA-sensitive fluorescence sensor. The response mechanism of the sensor was discussed in detail. The sensor exhibited a dynamic detection range from 7.90 × 10⁻⁸ to 1.66 × 10⁻⁵ mol L⁻¹ with a detection limit of 7.00 × 10⁻⁸ mol L⁻¹, and showed excellent reproducibility, reversibility, selectivity, and lifetime. The proposed sensor was successfully used for the determination of BPA in water samples and landfill leachate.     

A Simple and Highly Stable Porous Gold‐based Electrochemical Sensor for Bisphenol A Detection

A porous gold electrode with a uniform pore size was prepared by a simple single potential step method. It provided around 19 times more surface area than a bare gold electrode. The porous gold electrode, without any modification, exhibited good electrocatalytic activity towards the oxidation of bisphenol A (BPA). The effect of the pH and scan rate, on the porous gold electrode was studied and discussed. Under optimum conditions of the flow system, the calibration plot of BPA was linear over a wide range of concentration, from 2.0 nM to 800 nM (R²=0.999), and the detection limit was 2.0 nM (s/n=3). It was of interest that, the porous gold electrode showed an exceptional result in minimizing the fouling from the oxidation product of BPA and led to a very high operational stability of the electrode for the detection of BPA (560 consecutive times). The porous gold electrode showed good fabrication reproducibility and can be used to detect bisphenol A that leached from baby bottles and drinking water bottles. The obtained results were in good agreement with the GC‐MS method (P >0.05).     

单核和双核钌配合物在铟锡氧化物电极上的电化学行为及对双酚A的催化氧化

本文应用循环伏安法和微分脉冲伏安法研究了两种新型单、双核多吡啶钌(Ⅱ)配合物在铟锡氧化物(ITO)电极上的电化学行为及对双酚A(BPA)的催化氧化。研究结果表明,单、双核配合物在ITO电极上均出现两个归属为中心离子和亚胺基的氧化波,双核配合物的峰电流约为单核的2倍,表现为通过桥联配体在两中心离子间的电子转移速度较其与电极间的大。同时,两种配合物对BPA的氧化呈现相近的催化氧化活性。此外,讨论了pH值对单、双核钌配合物电化学行为的影响,比较分析了它们对BPA的催化氧化过程。     

A novel high selective and sensitive para-nitrophenol voltammetric sensor, based on a molecularly imprinted polymer-carbon paste electrode

By using a molecularly imprinted polymer (MIP) as a recognition element, the design and construction of a high selective voltammetric sensor for para-nitrophenol was formed. Para-nitrophenol selective MIP and a non-imprinted polymer (NIP) were synthesized, and then used for carbon paste (CP) electrode preparation. The MIP-CP electrode showed greater recognition ability in comparison to the NIP-CP. It was shown that electrode washing after para-nitrophenol extraction led to enhanced selectivity, without noticeably decreasing the sensitivity. Some parameters affecting sensor response were optimized and a calibration curve was plotted. A dynamic linear range of 8 × 10⁻⁹ to 5 × 10⁻⁶ mol L⁻¹ was obtained. The detection limit of the sensor was calculated as 3 × 10⁻⁹ mol L⁻¹. Thus, this sensor was used successfully for the para-nitrophenol determination in different water samples.     

Electrochemical Oxidative Determination and Electrochemical Behavior of 4‐Nitrophenol Based on an Au Electrode Modified with Electro‐polymerized 3,5‐Diamino‐1,2,4‐triazole Film

A simple and fast electrochemical method was described and evaluated to determine the hazardous compound, 4‐nitrophenol (4NP). In this work, concentration of 4NP was determined by differential wave voltammetry (DPV). A gold electrode (Au) was modified with 3,5‐diamino‐1,2,4‐triazole (35DT). The modified electrode (35DT‐Au) was characterized by using electrochemical impedance spectroscopy (EIS), fouirer transform infrared spektrofotometre (FTIR), cyclic voltammetry (CV) and DPV. The modified electrode showed more sensitivity towards 4NP compared to unmodified one. A wide linear concentration range from 0.24 to 130.6 μM was obtained for 4NP with a detection limit of 0.09 μM. In the reproducibility and repeatability studies, the relative standard deviation (RSD%) values of the method were obtained as 3.72 % and 2.56 %, respectively, which are acceptable values. This proposed method was successfully used for the analysis of 4NP in lake and tap water samples. Simplicity, sensitivity, selectivity and high efficiency of the proposed method can be used in routine analysis of trace amounts of 4NP in polluted waters.     

Simple and sensitive fluorimetric method for determination of environmental hormone bisphenol A based on its inhibitory effect on the redox reaction between hydroxy radical and rhodamine 6G [corrected

Peroxyl radical produced by Fenton-like reagent (Fe(III) + H₂O₂) oxidizes Rhodamine 6G and produces the quenching of its fluorescence. It is also found that bisphenol A has an inhibitory effect on the redox reaction. Based on this observation, an inhibitory kinetic fluorimetric method is reported for the determination of trace bisphenol A. The fluorescent inhibition of rhodamine 6G is measured by fix-time method. Under the optimum experimental conditions, the detection limit and the quantification limit for bisphenol A is 2.0 and 6.7 ng mL⁻¹, respectively; and the linear range of the determination is 0.024-0.4 μg mL⁻¹. The proposed method has been used for the determination of bisphenol A in environmental waters, river bottom sediment, generic soil, polycarbonate products and teeth filling samples with recoveries of 92.5-110.0%. The possible mechanism of the reaction has also been discussed.