脉冲激光沉积LiFePO4阴极薄膜材料及其电化学性能

采用脉冲激光沉积结合高温退火的方法在不锈钢基片上制备了LiFePO₄薄膜电极. XRD谱图显示, 经650 ℃退火制得的是具有橄榄石结构的LiFePO₄薄膜. 充放电测试表明, LiFePO₄薄膜具有3.45/3.40 V的充放电平台, 与LiFePO₄粉体材料相当. 首次放电容量约为27 mAh•g^－1, 充放电循环100次后容量衰减51%.     

壳聚糖单体溶胶凝胶煅烧合成LiFePO4/C正极

本文以壳聚糖单体为碳源兼凝胶剂,利用溶胶-凝胶煅烧合成了锂离子电池LiFePO₄/C正极材料,使用XRD和SEM对合成的材料进行表征. 用恒电流充放电测试了LiFePO₄/C电极的电化学性能,当壳聚糖单体与LiFePO4摩尔比为1:1.2时,600 ^oC煅烧的LiFePO4/C电极性能最佳,其粒径分布均匀（200 ～ 400 nm）,该电极0.2C倍率放电比容量为155 mAh.g^-1,30周期循环放电比容量仍保持152 mAh.g^-1,库仑效率为97.9 %.     

Synthesis of NiFe2O4 Nanowires with NiO Nanosheet as Precursor via a Topochemical Solid State Method

Large scale NiFe₂O₄ nanowires were synthesized with NiO nanosheets as precursor by means of the topochemical solid state method. The morphologies and magnetic properties of NiFe₂O₄ annealed at different temperatures were studied. An appropriate annealing temperature was requested to transfer NiO nanosheets and Fe^- ions into NiFe₂O₄ nanowires. In the beginning stage of synthesizing process, the shape of NiO nanosheets remained unchanged at low temperatures. And then, NiO nanosheets split into nanowires from 400℃ to 600℃. At last they transformed into nanoparticles from 700℃ to 1000℃. Thus, the optimized annealing temperature was selected as 600℃ because the NiFe₂O₄ obtained at 600℃(N600) exhibited a maximum aspect ratio of 50 with a diameter of 20 nm and a length of 1 μm. Furthermore, N600 also displayed the largest magnetization value of 26.86 A·m²/kg and the lowest coercivity(H_c) of 8914 A/m.     

固相烧结法制备锂离子电池正极材料Li2FeP2O7及其电化学性能研究

介绍了一种先冷冻干燥后固相烧结制备正极材料Li₂FeP₂O₇的方法. 利用X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)和傅里叶变换红外光谱(FTIR)对材料的组成和形态进行表征, 并通过循环伏安曲线(CV)和电化学阻抗谱(EIS)研究了Li₂FeP₂O₇材料的电化学性能. 研究发现, 合成Li₂FeP₂O₇的最佳温度为590 ℃, 此温度下反应较完全且产物杂质较少, 1.6C倍率下的放电比容量达到55 mA·h·g^?1, 明显高于其它温度下合成样品的放电比容量. 该温度下合成的Li₂FeP₂O₇还具有低阻抗和较大的交换电流密度, 说明这种合成方式有利于提高锂离子在Li₂FeP₂O₇中的扩散.     

纯相Li_2MnO_3薄膜的制备及作为锂离子电池正极材料的电化学行为

采用固相烧结法制备了纯相Li2MnO3正极材料及靶材,采用脉冲激光沉积(PLD)法在氧气气氛、不同温度下沉积了Li2MnO3薄膜.通过X射线衍射(XRD)和拉曼(Raman)光谱表征了薄膜的晶体结构,采用扫描电镜(SEM)观察薄膜形貌及厚度,利用电化学手段测试了Li2MnO3薄膜作为锂离子电池正极材料性能.结果表明,PLD方法制备的纯相Li2MnO3薄膜随着沉积温度升高薄膜结晶性变好.25℃沉积的薄膜难以可逆充放电,400℃沉积的薄膜具有较高的电化学活性和循环稳定性.相对于粉末材料,400与600℃制备的Li2MnO3薄膜电极平均放电电位随着循环次数的衰减速率明显低于相应的粉体材料.     

Electrochemical properties of niobium and phosphate doped spherical Li-rich spinel LiMn2O4 synthesized by ion implantation method

Spherical Li-rich lithium manganese oxide(LMO) spinel material was synthesized by an ion implanted method assisted by polyalcohol doped with Niobium and Phosphate simultaneously.The material was characterized by scanning electron microscopy,X-ray diffraction and BET specific surface area analysis.The electrochemical performances were investigated with galvanostatic techniques and cyclic voltammetry.The synthesis process was investigated with TG/DSC.The results show that the lithium ion can be immersed into the pore of manganese dioxide at a low temperature with the ion implanted method.The prepared materials have a higher discharge capacity and better crystallization than those prepared by solid phase method.The doped Nb can improve the capacity of the Li-rich LMO spinel and reinforce the crystal growth along(111) and(400) planes.The crystal grains show circular and smooth morphology,which makes the specific surface area greatly decreased.Phosphate-doped LMO spinel exhibits good high-rate capacity and structure stability.The prepared Li_(1.09)Mn_(1.87)Nb_(0.031)O_(3.99)(PO_4)_(0.021)delivers a discharge capacity of 119mAhg~(-1) at 0.2C(1C=148mAg~(-1)) and 112.8 mAhg~(-1) at 10 C,the discharge capacity retention reaches 98% at 1 ℃ after 50 cycles at 25 ℃ and 94% at 55 ℃.     

Synthesis and Electrochemical Performance of Co3O4/Graphene

Co3O4/reduced graphene oxide composites were synthesized via a simple electrochemical method from graphene oxide and Co（NO3）2·6H2O as raw materials.Co3O4 nanoparticles with sizes of around 30-50 nm were distributed on the surface of graphene nanosheets confirmed by scanning electron microscopy and transmission electron microscopy.Electrochemical properties of Co3O4/graphene composite were tested by cyclic voltammetry,galvanostatic charge-discharge,and electrochemical impedance spectroscopy.The Co3O4/reduced graphene oxide composite was used as the pseudocapacitor electrode in the 2 mol/L NaOH aqueous electrolyte solution.The Co3O4/reduced graphene oxide composite electrode exhibited a specific capacitance of 357 F/g at a current density of 0.5 A/g in a three-electrode system.72％ of capacitance was retained when the current density increased to 3 A/g.The Co3O4/reduced graphene oxide composite prepared electrodes show a high rate capability and excellent long-term stability.After 1000 cycles of charge and discharge,the capacitance is still maintained 87％ at a current density of 1 A/g,indicating that the composite is a oromising alternative electrode material used for supercapacitors.     

碳热还原辅助溶胶-凝胶法制备氟代聚阴离子型嵌/脱锂材料LiVPO4F/C

采用碳热还原辅助溶胶-凝胶法合成了锂二次电池正极材料LiVPO₄F/C, 探讨煅烧温度和煅烧时间对所制备材料纯度、结构和电化学性能的影响. 采用X射线衍射(XRD), 扫描电子显微镜(SEM), 恒流充放电, 电化学阻抗谱(EIS)和循环伏安(CV)等手段对不同煅烧温度和时间所得的材料进行结构表征和电化学性能测试. 当煅烧时间为4 h 时, 温度为450 ℃时, 能够得到纯相LiVPO₄F/C, 在0.1C、0.5C和1.0C倍率下, 电池放电比容量分别为193.2、175.6 和173.7 mAh·g^-1. 随着煅烧温度升高, Li₃V₂(PO₄)₃杂相逐渐增多, 650 ℃煅烧后的材料Li₃V₂(PO₄)₃ 成为主相. 优化煅烧时间也能够有效控制Li₃V₂(PO₄)₃ 杂相的生成, 能得到电化学性能良好的LiVPO₄F/C. 当煅烧温度为550 ℃时, 反应3 h后得到的产物综合电化学性能最优.     

锂离子电池正极材料Li_(1.2)Mn_(0.54-x)Ni_(0.13)Co_(0.13)Zr_xO_2的制备及电化学性能

为了改善富锂锰基正极材料Li1.2Mn0.54Ni0.13Co0.13O2的循环性能,采用燃烧法合成了正极材料Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06).通过X射线衍射(XRD)和扫描电镜(SEM)对其结构与形貌进行了表征,利用恒电流充放电测试,循环伏安(CV)及电化学交流阻抗谱(EIS)技术对其电化学性能进行测试.结果表明,Li1.2Mn0.54-xNi0.13Co0.13ZrxO2(x=0.00,0.01,0.02,0.03,0.06)正极材料均具有α-NaFeO2型层状结构;在室温,2.0-4.8 V电压范围,以0.1C和1.0C(充放电电流以1.0C=180 mA·g-1计算)倍率充放电进行测试,样品Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2的首次放电比容量分别为280.3和206.4 mAh·g-1.其中,在1.0C倍率下,100次循环后容量保持率由原来的73.2%提高到88.9%;以5.0C倍率充放电进行测试,经50次循环后,掺杂正极材料的放电比容量为76.5 mAh·g-1,而未掺杂材料仅有15.0 mAh·g-1.在50、25和-10°C,2.0C倍率条件下,掺杂正极材料的电化学性能均得到有效改善,其中,在-10°C经过50次循环后正极材料Li1.2Mn0.52Ni0.13Co0.13Zr0.02O2比未掺杂的正极材料相比,其放电比容量提高了61.1%.     

Influence of Post-annealing in N2 on Structure and Electrochemical Characteristics of LiNi0.5Mn1.5O4

LiNi_0.5Mn_1.5O₄ prepared by a spray drying method was re-treated in N₂ at 500, 600 and 700℃, respectively. Their structural and electrochemical properties were studied by means of Fourier transform infrared(FTIR), X-ray diffraction(XRD), and charge-discharge tests. The space group of the LiNi_0.5Mn_1.5O₄ transforms from P4₃32 to Fd3 m at an annealing temperature of 700℃. The electrochemical characteristics of the treated samples are closely related to the annealing temperature. The sample treated in N₂ at 500℃ shows both an improved rate capability and cyclic performance at a high temperature compared with the as-prepared sample, while the sample treated in N₂ at 700℃ shows dramatically decrease in its reversible capacity.     

二氧化锰/石墨烯纸电极的制备及其电化学性能

通过电化学法使溶液中的Mn²⁺电解氧化为MnO₂,沉积复合在石墨烯片膜上,形成由MnO₂/石墨烯复合材料构成的纸电极。 采用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)、循环伏安(CV)和恒流放电等技术手段对纸电极材料的结构、形貌以及电化学性能进行了研究。 结果表明,MnO₂球形颗粒均匀地沉积在石墨烯片膜上,形成了厚度45 μm的纸电极,经过380 ℃煅烧后,纸电极中的MnO₂晶型由γ-MnO₂转化为β/γ-MnO₂混合晶型,是良好的柔性Li/MnO₂电池的电极材料。 MnO₂/石墨烯纸电极在室温下0.1C放电容量达269 mA·h/g,而且电化学阻抗低、柔韧性好。     

Excess capacity on compound phases of Li2FeTiO4 composite cathode materials synthesized by hydrothermal reaction using optional titanium sources to boost battery performance

Li₂FeTiO₄ composites have been produced using commercial LiAC, FeCl₂ and different titanium sources by hydrothermal synthesis (HS) at 175 ℃ and subsequent annealing at 700 ℃. Impure phase TiO₂, Fe₂O₃ and FeTiO₄ were detected out among the Li₂FeTiO₄ composites with different titanium sources. Micron and nano-sized particles of Li₂FeTiO₄ were prepared from various titanium raw materials, with nano-sized particles predominating when titanium raw materials were layered hydrogen titanate nanowire (H₂Ti₃O₇NW, HTO-NW) and titanium oxide nanotubes (TiO₂NB). The Li₂FeTiO₄ composites synthesized by HTO-NW shows a primary particle size of 50-200 nm of high crystallinity staggered with undissolved nanowire with a diameter size of about 100 nm. The samples using one-dimensional nanometer titanium oxide (TiO₂ NB) as the raw material can get a super high initial discharge capacity of 367.8 mAh/g at the rate of C/10 and excellent cycling stability. The selection of raw materials and adopting multi-phase modification can be considered as an effective strategy to improve the electro-chemical properties of Li₂FeTiO₄ composite cathode materials for the lithium secondary battery.     

热处理对[NiFe/Cu/Co/Cu]_n多层纳米线磁性能的影响

采用双槽控电位法在阳极氧化铝(AAO)模板中制备了有序均一的[NiFe/Cu/Co/Cu]n多层纳米线阵列,并在不同温度下进行了热处理.利用X射线衍射(XRD)对热处理前后多层线的晶体结构进行了测试.考察了不同退火温度对多层线矫顽力、剩磁比、巨磁电阻(GMR)效应、磁灵敏度的影响.随热处理温度升高,多层纳米线中磁性微晶晶型取向越来越明显,晶体结构更均匀;多层纳米线的矫顽力和剩磁比先增大后减小.300°C下多层纳米线矫顽力达到最大值,GMR最大值可达59%,对应的磁电阻灵敏度(SV)为0.233%Oe-1.     

锂氧电池双功能还原石墨烯-LaFeO_3复合纳米催化剂的制备及性能

制备具有氧还原(ORR)与氧释放(OER)双功能催化活性的特殊孔道结构电催化剂是锂氧电池研究的挑战之一。本文以氧化石墨烯、硝酸铁、硝酸镧、柠檬酸为原料,结合溶胶凝胶和水热合成方法,制备出还原氧化石墨烯(RGO)与铁酸镧(LaFeO_3)复合的双功能催化剂(RGO-LaFeO_3)。X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱和Raman光谱分析结果确认该复合催化剂由纯相钙钛矿结构LaFeO_3和还原氧化石墨烯组成,扫描电子显微镜(SEM)观察到LaFeO_3纳米颗粒均匀地负载在RGO片层表面。锂氧电池测试结果指出,相对于LaFeO_3纳米粒子(NP-LaFeO_3),RGO-LaFeO_3催化剂具有更好的ORR和OER催化活性,归因于RGO特殊的三维导电多孔结构与LaFeO_3纳米粒子的协同催化作用。以RGO-LaFeO_3作为阴极催化剂的锂氧电池在限1000 m Ah?g~(-1)比容量、100 m A?g~(-1)电流密度条件下,可实现36周稳定的充放电循环,展示出良好的应用前景。     

Influence of annealing temperature on the electrochemical and surface properties of the 5-V spinel cathode material LiCr0.2Ni0.4Mn1.4O4 synthesized by a sol–gel technique

LiCr_0.2Ni_0.4Mn_1.4O₄ was synthesized by a sol–gel technique in which tartaric acid was used as oxide precursor. The synthesized powder was annealed at five different temperatures from 600 to 1,000 °C and tested as a 5-V cathode material in Li-ion batteries. The study shows that annealing at higher temperatures resulted in improved electrochemical performance, increased particle size, and a differentiated surface composition. Spinel powders synthesized at 900 °C had initial discharge capacities close to 130 mAh g^?1 at C and C/2 discharge rates. Powders synthesized at 1,000 °C showed capacity retention values higher than 85 % at C/2, C, and 2C rates at 25 °C after 50 cycles. Annealing at 600–800 °C resulted in formation of spinel particles smaller than 200 nm, while almost micron-sized particles were obtained at 900–1,000 °C. Chromium deficiency was detected at the surface of the active materials annealed at low temperatures. The XPS results indicate presence of Cr⁶⁺ impurity when the annealing temperature was not high enough. The study revealed that increased annealing temperature is beneficial for both improved electrochemical performance of LiCr_0.2Ni_0.4Mn_1.4O₄ and for avoiding formation of Cr⁶⁺ impurity on its surface.     

Synthesis and Electrochemical Properties of Highly Crystallized CuV2O6 Nanowires

CuV₂O₆ nanowires were prepared via a simple hydrothermal route using NH₄VO₃ and Cu(NO₃)₂ as starting materials. The structures and electrochemical properties of CuV₂O₆ nanowires were characterized by means of X-ray diffraction(XRD), scanning electron microscopy(SEM) and transmission electron microscopy(TEM). The results show that the CuV₂O₆ nanowires are about 100 nm in width and single crystalline grown along [001] direction. CuV₂O₆ nanowires delivered a high initial discharge capacity of 435 and 351 mA·h/g at current densities of 50 and 100 mA·h/g, respectively. The electrochemical kinetics of the CuV₂O₆ nanowires was also investigated by means of electrochemical impedance spectroscopy(EIS) and the poor rate performance was observed, which may be attributed to the low ion diffusion coefficient of the CuV₂O₆ nanowires.     

氨蒸发诱导法制备纳米结构LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2及其作为高功率型锂离子电池正极材料的性能

采用氨蒸发诱导法成功制备出纳米结构LiNi1/3Co1/3Mn1/3O2正极材料,借助X射线衍射(XRD)分析、扫描电镜(SEM)、透射电镜(TEM)、高分辨率透射电镜(HRTEM)、能量分散谱(EDS)和比表面测试等表征手段及恒电流充放电测试研究了其晶体结构、微观形貌和电化学性能.研究表明该方法制备出的材料具有良好的α-NaFeO2层状结构,阳离子混排程度低.纳米片交错堆积而成核桃仁状形貌,片与片之间形成许多纳米孔,而且纳米片的侧面属于{010}活性面,能够提供较多的锂离子的脱嵌通道.在室温下及3.0-4.6 V充放电范围内,该材料在电流密度为0.5C、1C、3C、5C和10C时放电比容量分别为172.90、153.95、147.09、142.16和131.23mAh?g-1.说明其具有优异的电化学性能,非常有潜力用于动力汽车等高功率密度锂离子电池中.     

钠锰比对NaxMnO2的性能和钠离子脱嵌过程的影响

采用高温固相法合成了Na_xMnO₂,并用X-射线衍射、X-射线光电子能谱、场发射扫描电镜、循环伏安、电化学阻抗谱和恒流充放电技术研究了钠锰比对材料的形态结构、电化学性能和钠离子脱嵌过程的影响. 结果表明,Na_xMnO₂ 主要由Na_0.7MnO₂ 和Na_0.91MnO₂ 组成,且Na_0.91MnO₂ 的量随着钠锰比的增加而增加. 随着钠锰比的增加,SEI 膜扩散、界面电化学反应和固相扩散的活化能先减少后增大,而材料的放电比容量则先增大后减少. 当钠锰比为0.80 时,合成的材料1C 倍率下首次放电比容量为152.8 mAh·g^-1,50 次循环容量保持率为80.6%,5C 大倍率下放电比容量为88.3 mAh·g^-1,表现出了良好的循环性能和倍率性,相应的SEI 膜扩散、界面电化学反应和固相扩散过程的活化能分别为68.23、40.07 和57.62 KJ·mol^-1.     

碳包覆CaSnO3纳米纤维作为高性能锂离子电池负极材料

采用静电纺丝技术制备出CaSnO3纳米纤维(CaSnO3 NFs)并作为模板,再经表面原位聚合酚醛树脂和碳化处理制得碳包覆CaSnO3纳米纤维(CaSnO3@C NFs)。使用X射线衍射、扫描电子显微镜、透射电子显微镜和X射线光电子能谱对材料的物相组成、形貌和微观结构进行了表征,通过循环伏安、恒电流充放电和交流阻抗谱研究了碳包覆及碳化温度对CaSnO3 NFs负极材料电化学性能的影响。结果显示,碳包覆改性使CaSnO3 NFs的电化学性能得到较大程度的提高,而且随着碳化温度的升高,CaSnO3@C NFs复合电极的比容量先增加后下降,600℃碳化获得的CaSnO3@C NFs?600复合材料具有最好的电化学性能。在0.1 A·g^-1的电流密度下,CaSnO3@C NFs?600电极的首圈放电比容量达到1102.2 mAh·g^-1,充放电循环100圈后比容量为548.8 mAh·g^-1,当电流密度提高到2 A·g^-1时,其比容量仍保持在333.5 mAh·g^-1。     

Effect of Nanoparticle Size on Gas-sensing Properties of Tin Dioxide Sensors

Sn(OH)₄ was prepared by the conventional solution precipitate method, followed by supercritical CO₂ drying. The resultant Sn(OH)₄ was divided into three aliquots and calcined at 400, 600 and 800℃, respectively, thus SnO₂ nanoparticles with average crystallite sizes of 5, 10 and 25 nm were obtained. Furthermore, three SnO₂ thick film gas sensors(denoted as sensors S-400, S-600 and S-800) were fabricated from the above SnO₂ nanoparticles. The adhesion of sensing materials on the surface of alumina tube is good. Compared to the sensors S-600 and S-800, sensor S-400 showed a much higher sensitivity to 1000 μL/L ethanol. On the other hand, sensor S-800 showed a much lower intrinsic resistance and improved selectivity to ethanol than sensors S-400 and S-600. X-Ray diffraction(XRD), transmission electron microscopy(TEM) and selective area electron diffraction(SAED) measurements were used to characterize the SnO₂ nanoparticles calcined at different temperatures. The differences in the gas sensing performance of these sensors were analyzed on the basis of scanning electron microscopy(SEM).