Combined effect of chemically compound graphene oxide‐calcium pimelate on crystallization behavior,morphology and mechanical properties of isotactic polypropylene

The combined nucleation effect of graphene oxide (GO) and calcium pimelate (CaPi) which are chemically compound together (expressed in GO ? CaPi) in isotactic polypropylene (iPP) was investigated. Fourier transform infrared (FTIR), X‐ray diffraction (XRD) and thermogravimetric analysis (TGA) verified that CaPi was chemically compound with GO by chelate bonds. The crystallization behavior and crystalline morphologies of iPP nucleated with different mass ratio of GO and CaPi were investigated. The crystallization peak temperature of iPP nucleated with 0.2 wt% GO ? CaPi with the mass ratio of 1:5 (GO1 ? C5) was increased by 8.3°C when compared with that of pure iPP, and the relative content of β‐crystal reached up to 0.7962. Whereas, the crystallization peak temperature of iPP nucleated with 0.2 wt% GO and CaPi which are blended together by mechanical force (expressed in GO + CaPi) with the mass ratio of 1:5 (GO1 + C5) was only increased by 5.0°C. It was attributed to that the aggregation of GO + CaPi caused the decrease of the crystallization peak temperature, while the GO1 ? C5 uniformly dispersed in the iPP matrix. Unexpectedly, the relative content of β‐crystal of iPP nucleated with 0.02 wt% GO1 ? C5 reached up to 0.8094, and the crystallization peak temperature was increased by 6.7°C compared with that of pure iPP. Meanwhile, the impact strength, tensile strength and heat deflection temperature of iPP nucleated with 0.02 wt% GO1 ? C5 increased by almost 45.86%, 2.03% and 7.7°C, respectively. The iPP nucleated with GO1 ? C5 obtained a balance between stiffness and toughness and the thermo‐mechanical property of nucleated iPP was improved.     

Improving hydrophilicity and protein resistance of poly(vinylidene fluoride) membranes by blending with amphiphilic hyperbranched-star polymer

To endow hydrophobic poly(vinylidene fluoride) (PVDF) membranes with reliable hydrophilicity and protein resistance, an amphiphilic hyperbranched-star polymer (HPE-g-MPEG) with about 12 hydrophilic arms in each molecule was synthesized by grafting methoxy poly(ethylene glycol) (MPEG) to the hyperbranched polyester (HPE) molecule using terephthaloyl chloride (TPC) as the coupling agent and blended with PVDF to fabricate porous membranes via phase inversion process. The chemical composition changes of the membrane surface were confirmed by X-ray photoelectron spectroscopy (XPS), and the membrane morphologies were measured by scanning electron microscopy (SEM). Water contact angle, static protein adsorption, and filtration experiments were used to evaluate the hydrophilicity and anti-fouling properties of the membranes. It was found that MPEG segments of HPE-g-MPEG enriched at the membrane surface substantially, while the water contact angle decreased as low as 49 degrees for the membrane with a HPE-g-MPEG/PVDF ratio of 3/10. More importantly, the water contact angle of the blend membrane changed little after being leached continuously in water at 60 degrees C for 30 days, indicating a quite stable presence of HPE-g-MPEG in the blend membranes. Furthermore, the blend membranes showed lower static protein adsorption, higher water and protein solution fluxes, and better water flux recovery after cleaning than the pure PVDF membrane.     

Cellulose acetate nanocomposite ultrafiltration membranes tailored with hydrous manganese dioxide nanoparticles for water treatment applications

Hydrous manganese dioxide (HMO) nanoparticles incorporated cellulose acetate (CA) composite ultrafiltration (UF) membranes are prepared with the aim of improving the water permeation and BSA contaminant removal. The HMO nanoparticles are synthesized from manganese ion and characterized by FT‐IR, XRD, and FESEM. The effect of variation of HMO on CA membranes is probed using FT‐IR, EDAX, contact angle, SEM, and AFM analysis to demonstrate their chemical functionality, hydrophilicity, and morphology. CA/HMO membranes are showing the enhancement in pure water flux (PWF), water uptake, porosity, hydrophilicity, fouling resistance, BSA rejection, and flux recovery ratio (FRR). CA‐1 membrane displayed higher PWF (143.6 Lm²h^?1), BSA rejection (95.9%), irreversible fouling (93.3%), and FRR (93.3%). Overall results confirmed that the CA/HMO nanocomposite UF membranes overcome the bottlenecks and shows potential for water treatment applications.     

热致相分离法偏二氯乙烯-氯乙烯共聚物多孔膜的制备及性能

以偏二氯乙烯-氯乙烯共聚物[P(VDC-co-VC)]为成膜聚合物, 邻苯二甲酸二甲酯(DMP)为稀释剂, 采用热致相分离(TIPS)法制备了具有多孔结构的P(VDC-co-VC)膜. 通过聚合物-稀释剂二元体系相图、 场发射扫描电镜(FESEM)、 差示扫描量热仪(DSC)、 X射线衍射(XRD)、 原子力显微镜(AFM)、 纯水通量、 接触角、 孔径及其分布、 截留率及力学性能等研究了聚合物含量对P(VDC-co-VC)多孔膜结构和性能的影响. 结果表明, P(VDC-co-VC)-DMP二元体系成膜过程以液-液(L-L)分相为主, 随着聚合物含量增加, 膜的横截面由类花瓣状结构向胞腔状结构转变, 膜的孔连通性降低, 结构变得较为致密, 同时膜上表面孔隙率降低, 粗糙度增大. L-L分相时间和聚合物含量的变化, 导致膜结晶度先降低后增大. 聚合物含量的增加使膜上表面接触角、 断裂强度及蛋白截留率增加, 但膜的平均孔径、 孔隙率及纯水通量先增加后减小. 当聚合物质量分数为30%时, 所得膜通透性较优, 断裂强度可达7.5 MPa.     

三醋酸纤维素纳米纤维膜的制备及其油水分离应用

石油开采和油船运输泄露的油污污染日益突出,使得质轻、亲水疏油的油水分离材料得到广泛关注。本文在无任何添加剂条件下,以三醋酸纤维素(TCA)/N,N-二甲基乙酰胺(DMAc)溶液通过热致相分离(TIPS)制备TCA纳米纤维膜。研究了淬火时间、温度和聚合物浓度等条件对TCA纳米纤维膜形貌的影响。TCA纳米纤维膜的形貌、孔隙率和比表面积通过SEM、乙醇法和N2吸脱附表征。实验结果表明,最佳实验条件为:淬火时间180 min、淬火温度-20℃、聚合物质量分数5%,得到直径为(110±28)nm均匀纤维膜。与块状TCA流延膜相比,TCA纳米纤维膜的高孔隙率和大比表面积以及表面特殊的微/纳结构,使其水接触角由86.2°增加到137.5°。由于高疏水性和亲油性以及强烈的毛细作用,TCA纳米纤维膜的吸油容量达到21.5 g/g,分别是流延膜的20~42倍,且可快速吸收油水混合物中的油层。TCA纳米纤维膜是一种可生物降解的溢油污染清洁材料。     

Preparation,properties, and application of polypropylene micro/nanofiber membranes

Nanofiber membranes have huge potential applications in many areas due to their unique properties. However, the thermoplastic micro/nanofiber membranes were rarely reported. In this paper, polypropylene (PP) nanofibers were prepared by melt extrusion of immiscible blends of PP, cellulose acetate butyrate (CAB), and subsequent removal of the CAB matrix. The wet‐laid application was used to make PP nanofiber membranes and PP‐g‐MAH/nonwoven micro/nanofiber membrane. The properties of membranes including morphology, apparent density, porosity, contact‐angle, pore size distribution, and water flux were characterized. The results showed that the consequent membranes were provided with optimistic porosity and pore size distribution. Moreover, they were all with high pure water fluxes, which were superior to that of PP microporous membrane. They performed an excellent separation performance of TiO₂ suspension and dyeing wastewater. The work revealed this method could be an efficient one to make thermoplastic polymer micro/nanofiber membranes, and they would have a brilliant potential application for water treatment. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication of blend hydrophilic polyamide imide (Torlon®)-sulfonated poly (ether ether ketone) hollow fiber membranes for oily wastewater treatment

Blend hydrophilic polyamide imide (PAI)-sulfonated poly (ether ether keton) (SPEEK) hollow fiber membranes were fabricated for oil-water emulsion separation. The structure and performance of the membranes were examined by FESEM analysis, N₂ permeation, overall porosity, collapsing pressure, water contact angle, pure water flux, molecular weight cutoff (MWCO), and oil rejection tests. By studying ternary phase diagrams of polymer/solvent-additive/water system, the higher phase-inversion rate was confirmed for the solutions prepared at higher PAI/SPEEK ratio. A more open structure with larger finger-likes was observed by increasing PAI/SPEEK ratio. Mean pore size of 81 nm, overall porosity of 79% and water contact angle of 58° were obtained for the improved membrane prepared by PAI/SPEEK ratio of 85/15. Increasing SPEEK ratio resulted in lower mechanical stability in terms of collapsing pressure. Pure water flux of about 2.5 times of the plain PAI membrane was found for the improved membrane. MWCO of 460 kDa was found for the improved blend membrane. From oil rejection test, all the membranes demonstrated an oil rejection of over 95%. The improved membrane showed a lower rate of permeate flux reduction compared to the plain membrane which was related to the smaller fouling possibility. Less fouling resistance of the improved membrane was related to the higher flux recovery ratio (about 92%). For all the membranes, the dominant fouling mechanism was found to be the cake filtration. The improved PAI-SPEEK hollow fiber membranes was found to be practical for ultrafiltration of oily wastewaters.     

Fabrication of cellulose triacetate/graphene oxide porous membrane

Cellulose triacetate (AC)/graphene oxide (GO) porous membranes were successfully fabricated by combining ultrasonication and phase inversion method. The structures and morphologies of the resultant composite membranes were investigated by X‐ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy, respectively. Microscopic and X‐ray diffraction measurements revealed that GO sheets were uniformly dispersed within the AC matrix. The pore size and structure were modulated by changing GO concentration from 0.25 to 1 wt%. Membrane thermal properties were also studied. Among all tested membranes, the most favorable GO amount was 1 wt%, giving Td_3% of 274°C, which represents a 22°C enhancement compared with AC. Conversely, the membranes showed improved barrier properties against water and ethanol. The decrease of both ethanol and water fluxes was assigned to the stabilization of composite membrane structure, as a result of GO progressive addition. Bovine serum albumin rejection assay indicated an increasing from 78% in the case of CA membrane to 99% in the case of CA/GO 1 wt% of the rejection degree after 90 min. Copyright © 2015 John Wiley & Sons, Ltd.     

基于多巴胺自聚合与表面接枝PHGH制备抗菌纳滤膜

在水溶液中将聚六亚甲基单胍盐酸盐(PHGH)共价接枝在经多巴胺自聚合改性的聚砜膜表面, 制备具有抗菌性能的纳滤膜. 采用全反射红外光谱(ATR-FTIR)、 扫描电子显微镜(SEM)和接触角测试考察膜表面的结构、 形貌和亲水性变化. 探讨PHGH含量对膜的接枝度及分离性能的影响, 并对膜的抗菌性能进行了评价. 结果表明, 经过多巴胺的自聚合和表面接枝PHGH后, 聚砜膜表面形成了具有纳滤分离性能的活性层, 并且膜表面亲水性得到改善. 随着PHGH含量的增大, 膜的纯水通量降低, 而对无机盐和染料的截留性能提高. 接枝后的复合膜具有较高的抗菌性能, 当PHGH含量为3%(质量分数)时, 抗菌率可达98.5%.     

医用多孔壳聚糖膜的制备及性能研究

以邻苯二甲酸二丁酯为致孔剂,制备了多孔壳聚糖膜,并用扫描电镜对其表面和断面形貌进行了分析,同时对膜的吸水性、水蒸气透过性、比表面积、力学性能及生物相容性等进行了考察。分析结果表明:以邻苯二甲酸二丁酯为致孔剂,制备的多孔壳聚糖膜孔径均匀,吸水性好,孔隙率高,比表面积大,膜的最大吸水率、孔隙率和比表面积分别为196%、71.5%和1.0472 m2.g-1;膜的力学性能好,最大抗拉强度为273.17MN/m2。     

Preparation of Superhydrophobic ZnO Films on Zinc Substrate by Chemical Solution Method

Superhydrophobic surface was prepared on the zinc substrate by chemical solution method via immersing clean pure zinc substrate into a water solution of zinc nitrate hexahydrate[Zn(NO₃)₂·6H₂O] and hexamethylenetetraamine( C₆H₁₂N₄) at 95 ℃ in water bath for 1.5 h, then modified with 18 alkanethiol. The best resulting surface shows superhydrophobic properties with a water contact angle of about 158° and a low water roll-off angle of around 3°. The prepared samples were characterized by powder X-ray diffraction(XRD), X-ray photoelectron spectroscopy (XPS), energy-dispersive X-ray spectroscopy(EDX), transmission electron microscopy(TEM), and scanning electron microscopy(SEM). SEM images of the films show that the resulting surface exhibits flower-shaped micro- and nano-structure. The surfaces of the prepared films were composed of ZnO nanorods which were wurtzite structure. The special flower-like micro- and nano-structure along with the low surface energy leads to the surface superhydrophobicity.     

氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜

采用层层自组装法在改性聚丙烯腈(PAN)膜表面交替沉积聚乙烯亚胺(PEI)和聚丙烯酸-氧化石墨烯(PAA-GO)混合液,制得了单价离子选择性复合膜。X射线衍射(XRD)测试结果表明成功合成了氧化石墨烯(GO)并在复合膜中均匀分散。扫描电镜(SEM)观察结果证实了多层聚电解质PEI/PAA-GO成功地组装在基膜上,并用紫外-可见(UV-Vis)光谱进一步证实了组装过程的均匀性和连续性。接触角和性能测试表明加入GO后,复合膜的亲水性和单价阳离子的选择性明显增大。这种高通量、高选择性的防污复合膜在分离和水的软化方面有很好的应用前景。     

Polymer/graphite nanocomposites: Effect of reducing the functional groups of graphite oxide on water barrier properties

Water barrier properties (i.e., water resistance) of poly(styrene-co-butyl acrylate)/graphite oxide (poly(St-co-BA)/GO) nanocomposites were studied using hydrophobicity and permeability analysis. Poly(St-co-BA)/GO nanocomposite latices were obtained using the miniemulsion polymerization technique. The hydrophobicity of the synthesized nanocomposites was studied using contact angle measurements, while water permeability was obtained by measuring the moisture vapor transmission rate (MVTR). The nanocomposites were treated with hydrazine hydrate in order to reduce the functional groups on graphite oxide (GO). The focus was on determining the effect of reducing the functional groups of GO on the water barrier properties of its polymer nanocomposites. In general, the nanolayered graphene platelets in GO and RGO resulted in lower water permeation in the final films compared to pure polymer. However, results showed that nanocomposites containing the reduced-GO (RGO) had better water resistance and barrier properties compared to those made with unreduced GO (i.e., as-prepared GO). The nanocomposites containing RGO had higher hydrophobicity and lower water uptake and MVTR compared to those made with as-prepared GO, resulting in better barrier performance. This was attributed to the high hydrophobic nature of the RGO, which exhibited lower water solubility that resulted in films with lower MVTR values compared to those made with as-prepared GO.     

Preparation of stable and superior flux GO/LDH/PDA‐based nanofiltration membranes through electrostatic self‐assembly for dye purification

Graphene oxide (GO) has triggered significant attention as a new type of self‐assembly membrane material. However, the low filtration flux and unstable performance of GO membrane limit its practical application. Hence, in this work, layered double hydroxides (LDHs), as a 2D material with double‐layer channel structure and positive electricity, were self‐assembled with GO at weight ratio of 7:3 by electrostatic interaction. Then, the GO/LDH hybrids combined with polydopamine (PDA) to obtain stable and high‐flux GO‐based membranes through vacuum filtration and the structure and morphology of as‐prepared samples were characterized by FT‐IR, XRD, XPS, and SEM. Furthermore, the separation performance and surface electronegativity of membranes were tested via pure water flux, rejection efficiency, recycle experiments, and zeta potential. Results revealed that the stability and flux of composite membrane were enhanced significantly compared with neat GO‐based membrane. Further, the dye rejection rate of methylene blue (MB) is higher than Congo red (CR) and rhodamine B (Rh B) and reached to 99.8%.     

Novel stand-alone PVA mixed matrix membranes conjugated with graphene oxide for highly improved reverse osmosis performance

In this research, an innovative Poly (vinyl alcohol) (PVA) reverse osmosis (RO) membrane with exceptional attributes was fabricated. Graphene Oxide (GO) nanosheets and Pluronic F-127 were infused within crosslinked PVA to fabricate thin film mixed matrix membranes. The newly synthesized membranes were evaluated in terms of several parameters like surface roughness, hydrophilicity, salt rejection, water permeability, Chlorine tolerance and anti-biofouling property, utilizing a dead-end RO filtration unit. Typical characterization techniques were used to assess the characteristics of the membranes. These include SEM, AFM, contact angle measurements and mechanical strength analysis. The conjugation of Pluronic F-127 and GO enhanced the overall performance of the membranes. The modified membranes surfaces had less roughness and higher hydrophilicity in comparison with the unmodified ones. This research showed that membranes that contained 0.08 wt% and 0.1 wt% GO exhibited superior selectivity, mechanical strength, Chlorine tolerance and anti-biofouling property. The truly significant outcome to evolve from this investigation is that improvements have been accomplished while PVA was used as a stand-alone RO layer without the use of any substrate. This study showed that crosslinking of PVA and modifying it with proper fillers overcame the common PVA downsides, primarily swelling and rupture under exceptionally high pressure.     

Comparison of redox initiated graft polymerisation and sulfonation for hydrophilisation of polyethersulfone nanofiltration membranes

Three polyethersulfone nanofiltration membranes, including two commercial membranes (NFPES10 and N30F) and one lab-made membrane (N71), were hydrophilised in view of an increased water flux and a reduction of membrane fouling.Non-modified as well as modified membranes were characterized using contact angle measurements, water fluxes and retention of sugars.At first, redox initiated graft polymerization was applied, and the influence of reaction time, initiator concentration and monomer concentration were investigated. It was observed that grafting always resulted in a significant reduction of the contact angle. The higher the reaction time, the lower was the contact angle, but the initiator and monomer concentration had no effect when above a threshold value. Grafting results in a decrease of the water flux, while the retention of raffinose increased.A comparison was made with the addition of sulfonated polyethersulfone to the polymer solution. By blending polyethersulfone and sulfonated polyethersulfon, a sufficiently high viscosity could be achieved. The influence of the blending ratio was investigated. The larger the fraction of sulfonated polyethersulfon, the more hydrophilic the membrane became. The addition of sulfonated polyethersulfon, however, has also an influence on the water flux and on the retention of sugars. An important conclusion is also that the membranes containing sulfonated polyethersulfone are significantly more hydrophilic than the ones that have been modified through the grafting technique.     

HBPE-g-PVDF/PVDF blend nanofiltration membrane: preparation and characterization

Hyperbranched polyester-grafted poly(vinylidene fluoride) (HBPE-g-PVDF) was synthesized and used as additive in preparation of PVDF blend membranes. HBPE-g-PVDF copolymer was characterized with FTIR and TGA techniques. The prepared membranes were also characterized with SEM, AFM and contact angle measurement. The performance of prepared membranes as nanofiltration membrane was studied by pure water flux (PWF), salt rejection, dynamic and static fouling tests. The results showed that hydrophilicity of prepared membranes greatly increased after blending, and their pore size and pore size distribution and so PWF of blend membranes increased.     

Fabrication of ball clay based low-cost ceramic membrane supports and their characterization for microfiltration application

In this study, the uniaxial pressing method was employed to fabricate low-cost ceramic membrane supports using inexpensive clays for microfiltration applications. The primary precursors used to make different membrane supports (S1–S3) were Ball clay and China clay. Thermogravimetric analysis (TGA), particle size distribution (PSD), contact angle measurements, X-ray diffraction (XRD), and scanning electron microscopy (SEM) were performed in addition to water flux, porosity, water permeability, and average pore size measurements to characterize the membrane. SEM analysis revealed that the surface morphology of the membrane supports varies significantly depending on the raw material composition. The contact angle analysis of the supports revealed that they are hydrophilic, which is suitable for microfiltration applications. The water permeability, average pore size, and porosity of the membrane supports (S1–S3) were 4.31 × 10^?6 – 2.77 × 10^?6 m³/m²s kPa, 1.18–0.31 μm, 44–41%, respectively. Furthermore, the membranes' high pH and chlorine resistance show their suitability for use in harsh chemical cleaning. The production cost of membranes based on raw materials, pressing, and sintering was estimated to be Rs.1319/m² ($17.07), Rs. 978/m² ($12.66) and Rs. 924/m² ($11.96) for the supports S1, S2, and S3, respectively. Thus, membrane supports with low-cost clay materials are now suggested for microfiltration applications.     

Hydrophilic modification of polypropylene ultrafiltration membrane by air‐assisted polydopamine coating

Coating by a mussel inspired polydopamine (PDA) is a simple and promising strategy to modify the hydrophilicity of polymer membrane surfaces. In this work, PDA coating was used to modify polypropylene (PP) ultrafiltration hollow fiber membrane. PDA coating parameters, ie, solution concentration and coating time were varied, and the effect of those parameters on membrane morphology, porosity, water contact angle, and pure water flux was investigated. In addition, air‐assisted PDA coating process was also conducted by channelling the air through PP membrane to avoid pore blocking and prevent water flux decline. The results showed that PDA coating successfully improved the hydrophilicity of PP membrane indicated by the decrease of water contact angle from 110° to 67° after coated by 3 g/L of PDA solution for 3 hours. The addition of air permeation on membrane lumen also increased pure water flux up to 511.2 L/m².h, a 270% increase from unmodified PP membrane. It might be associated to the pore blocking prevention that has been proven by SEM image and the membrane porosity that was increased about 4%.     

四乙基氢氧化铵改性聚偏氟乙烯接枝聚丙烯酸油水分离膜的制备

使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF), 以过氧化苯甲酰(BPO)为引发剂, 将丙烯酸(AA)接枝到改性PVDF骨架上, 合成了聚偏氟乙烯接枝聚丙烯酸(PVDF-g-PAA)共聚物, 通过浸没沉淀法制备了PVDF-g-PAA亲水性油水分离膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和过滤试验分析了膜的结构和分离性能. 研究了不同接枝条件对PVDF-g-PAA膜接枝率的影响. 同时, 通过膜接枝率与膜表面接触角的关系确定最佳接枝条件. 结果表明, TEAH使PVDF脱去HF产生碳碳双键且PAA接枝到改性的PVDF骨架上, 膜内外孔隙分布均匀; PVDF-g-PAA膜的接触角随着接枝率的提高而降低. 接枝单体AA含量为45%, 接枝温度为85 ℃, 接枝4 h制备的PVDF-g-PAA膜的接枝率为20.1%, 孔隙度为65.3%, 平均孔径为78.0 nm, 接触角为57.5°, 且在60 s内接触角降至14.3°; 纯水通量提高到571.33 L/(m²·h), 截留率和水通量恢复率分别达到94.3%和88.7%, 且通量衰减率仅为9.8%. 与纯PVDF膜相比, PVDF-g-PAA膜的分离性能显著提高.