Joined ellipsometry and voltametry investigation on the second discharge plateau in Ni(OH)2

The electrochemical properties of nickel hydroxide, produced via an electrodialysis process are studied by means of cyclic voltametry and in-situ ellipsometry methods. The Ni(OH)₂ electrodes are thin layers of nickel hydroxide powder deposited on a polished platinum substrate. Electrochemical and optical properties are investigated in a voltage domain including the so-called “second discharge process”. The reduction of nickel hydroxide proceeds at two successive potentials with a recovering of the initial optical data only after the second discharge step. The first discharge step leads to a nickel hydroxide not fully discharged while the second discharge step is coupled both to a sudden change in the nickel hydroxide properties and an agglomeration of particles phenomenon. Project financed by the E.U., program Brite Euram BRPR-CT97-0515 (NEARBY) Paper presented at the 7th Euroconference on Ionics, Calcatoggio, Corsica, France, Oct. 1–7, 2000.     

Effect of synthesis temperature on the phase structure and electrochemical performance of nickel hydroxide

Nickel hydroxide powder is prepared by chemical precipitation method, and the effect of synthesis temperature on the phase structure and electrochemical performances of nickel hydroxide is investigated. The phase structure is characterized by X-ray diffraction (XRD), and the electrochemical performances are characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and charge/discharge tests. The XRD results show that low temperatures (0–20 °C) induce the precipitation of badly crystallized nickel hydroxide while at high temperatures (40–60 °C) crystallized β-nickel hydroxide is formed. Electrochemical performance tests show that the nickel hydroxide synthesized at low temperature has better electrochemical reversibility, lower electrochemical reaction impedance, and higher discharge capacity than that of the nickel hydroxide synthesized at high temperature.     

Structure and electrochemical performance of Y(III) and Al(III) codoped amorphous nickel hydroxide

Amorphous nickel hydroxide codoped with rare earths Y(III) and Al(III) has been synthesized by the chemical precipitation method combined with the rapid freezing technique. The microstructure and morphology of the prepared sample were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectra. The electrochemical performance of the sample was characterized by the charge/discharge test and cyclic voltammetry. The results show that this amorphous nickel hydroxide codoped with Y(III) and Al(III) has many structural defects and therefore results in a relatively high specific capacity (351.83 mA h g^?1 at a charge/discharge rate of 0.2 C) and good electrochemical reversibility.     

Synthesis and electrochemical performance of α-nickel hydroxide codoped with Al3+ and Ca2+

α-Nickel hydroxide codoped with Al³⁺ and Ca²⁺ was prepared by chemical coprecipitation method. The phase structure and surface morphology of the prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical performances of the prepared samples were analyzed by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge/discharge tests. XRD and SEM tests reveal that the Al³⁺/Ca²⁺ codoped α-nickel hydroxide has a relatively good crystallization and a very coarse surface. Electrochemical tests show that the Al³⁺/Ca²⁺ codoped α-nickel hydroxide has higher proton diffusion coefficient, lower electrochemical reaction resistance, and higher discharge capacity (395.3 mAh g^?1 at 0.2 C) than the Al³⁺ singly doped α-nickel hydroxide, which indicates its potential application as an electrode material for secondary alkaline batteries.     

Synthesis and electrochemical performance of mixed phase α/β nickel hydroxide by codoping with Ca<Superscript>2+</Superscript> and PO<Subscript>4</Subscript><Superscript>3−</Superscript>

Nickel hydroxide with a unique mixed phase α/β-Ni(OH)₂ was prepared by partially substituting Ca²⁺ for Ni²⁺ with supersonic co-precipitating method firstly. The crystal structure and morphology of the samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The results show that the Ca-substituted Ni(OH)₂ by adding PO₄ ^3? is α/β mixed phase, while the undoped Ni(OH)₂ and the Ca-substituted Ni(OH)₂ without adding PO₄ ^3? are pure β phase. Furthermore, the Ca-substituted Ni(OH)₂ by adding PO₄ ^3? exhibits irregular shape and contains many intercalated water molecules and anions as proven by SEM and FT-IR. Meanwhile, the prepared samples were added into micro-sized beta nickel hydroxide to form biphase electrode materials for Ni-MH battery. The electrochemical performances of the biphase electrodes were characterized by cyclic voltammetry (CV) and charge/discharge tests. The results demonstrate that the biphase electrode with mixed phase α/β-Ni(OH)₂ exhibits higher electrochemical activity, better electrochemical reversibility and charge efficient, higher discharge potential, and better cyclic stability. The specific discharge capacity of Ca-substituted α/β-Ni(OH)₂ electrode can retain 271.7 and 238 mAh/g after 80 cycles at 0.2 and 0.5 C, respectively. This indicates that it may be a promising positive active material for alkaline secondary batteries. The results reported in this work may be useful for the designing and synthesizing of nickel hydroxide materials with superior performance.     

Synthesis and electrochemical performance of amorphous nickel hydroxide codoped with Fe<Superscript>3+</Superscript> and CO<Stack><Subscript>3</Subscript><Superscript>2−</Superscript></Stack>

Amorphous nickel hydroxide codoped with Fe³⁺ and CO₃²⁻ was synthesized by micro-emulsion precipitation method combined with rapid freezing technique. The microstructure and composition of the sample were characterized by X-ray diffraction and IR analysis. The electrochemical performance of the sample was analyzed by cyclic voltammetry, electrochemical impedance spectroscopy, and charge–discharge tests. The results showed that the Fe³⁺ and CO₃²⁻ codoping enhances the amorphous feature of the prepared nickel hydroxide. Moreover, the Fe³⁺ and CO₃²⁻ codoping could increase the specific capacity and improve the electrochemical reversibility of the amorphous nickel hydroxide electrode.     

Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@MnO<Subscript>2</Subscript> core shell arrays on nickel foam with excellent electrochemical performance for aqueous asymmetric supercapacitor

At present, a lot of attention has been paid to the reasonable design and synthesis of materials with core shell structure for high-performance supercapacitors. Herein, the Co₃O₄@MnO₂ core shell arrays on nickel foam are successfully synthesized via a facile and effective hydrothermal method followed with annealing process. The sample was characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Electrochemical performance of the Co₃O₄@MnO₂ material was studied using cyclic voltammetry, charge/discharge cycling, and electrochemical impedance measurements in 6 mol L^?1 KOH aqueous electrolyte. The results indicated that the Co₃O₄@MnO₂ material presented excellent electrochemical performance in terms of specific capacitance, cyclic stability, and charge/discharge stability.     

Ageing of nickel used as sensitive material for early detection of sudomotor dysfunction

The surface ageing of nickel electrodes was studied in the frame of the development of non-invasive biomedical devices, dedicated to the detection of sudomotor dysfunction manifested by an alteration of the ionic balance in human sweat. In this kind of technology, low voltage potentials with variable amplitudes are applied to nickel electrodes, placed on skin regions with a high density of sweat glands, and the electrical responses are measured. The trick is that nickel electrodes play alternately the role of anode and cathode, thus the analysis of the temporal evolution of the physico-chemical properties of nickel is of prime importance to ensure the good performance of the device. Electrochemical measurements coupled to surface chemical characterizations (X-ray photoelectron spectroscopy (XPS), Time of Flight-Secondary Ion Mass Spectrometry (ToF-SIMS)) were performed on pure Ni samples, immersed in buffered chloride solutions mimicking human sweat. The shapes of voltammograms, recorded in a restricted anodic potential range, show that the nickel surface was gradually passivated as a function of the number of scans. This was confirmed by XPS data, with the formation of a 1 nm thick duplex layer composed by nickel hydroxide (outermost layer) and nickel oxide (inner layer). In a negative extended potential range, though the electrochemical behavior of electrodes was not modified upon cycling the potential, XPS data show that the inner layer was thickening, indicating a surface degradation of the nickel electrode. Below pitting potentials, adsorbed chloride was only hardly detected by XPS, and the surface composition of the nickel samples was similar after treatments in chloride or chloride-free buffered solutions. In a larger potential range enabling to reach the breakdown potential, the highly chemically sensitive ToF-SIMS characterization pointed out that the surface concentration of adsorbed chloride was higher in pits than elsewhere on the surface sample.     

Electrochemical performance of La2O3-coated layered LiNiO2 cathode materials for rechargeable lithium-ion batteries

Uncoated and La₂O₃-coated LiNiO₂ cathode materials were synthesized by polymeric sol gel process using metal nitrate precursors at 600 °C for 10 h. The structure and electrochemical properties of the surface-coated LiNiO₂ materials were characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry, charge/discharge and electrochemical impedance spectroscopy techniques. X-ray powder diffraction and SEM result show that no significant bulk structural differences were observed between the lanthanum oxide coated and pristine LiMn₂O₄. The galvanostatic charge/discharge studies on the uncoated and lanthanum oxide-coated LiNiO₂-positive material at 0.5-C rate in the potential range between 3 and 4.5 V revealed that lanthanum oxide-coated positive electrode material has enhanced charge/discharge capacities; 2.0 wt.% of lanthanum oxide-coated LiNiO₂-positive material has satisfied the structural stability, high reversible capacity and high electrochemical performances.     

Synthesis and characterization of stable Co and Cd doped nickel hydroxide nanoparticles for electrochemical applications

The present paper describes the physical-chemical characterization and electrochemical behavior of a new nanomaterial formed by the addition of cadmium and cobalt atoms into the structure of nickel hydroxide nanoparticles, these ones synthesized by an easy sonochemical method. Particles of about 5nm diameter were obtained and characterized by high resolution transmission electron microscopy (HRTEM), X-ray diffraction and Raman spectroscopy. Different nickel hydroxide nanoparticles were immobilized onto transparent conducting substrates by using electrostatic layer-by-layer providing thin films at the nanoscale and the electrochemical behavior was investigated. The formation of a mixed hydroxide was corroborated by observation of very interesting properties as redox potential shifting to less positive potentials and high stability when submitted to long electrochemical cycling or high times of ultrasonic synthesis, suggesting practical applications.     

Electrochemical characterization of a lithiated mixed nickel-cobalt oxide (LiNi0.5Co0.5O2) prepared by sol-gel process

Lithiated transition metal oxides having a layered structure and general formula LiMO₂, have been extensively studied as positive electrode active materials for lithium or lithium-ion batteries. In particular, lithium nickel dioxide (LiNiO₂) and lithium cobalt dioxide (LiCoO₂) present a layered structure with high diffusion coefficients for the lithium ion. This latter property is very important in order to realize practical devices having high discharge rates. LiNiO₂, compared with LiCoO₂, has the advantage to be a cheaper material with a higher specific capacity for lithium cycling, but its stability upon cycling can be greatly influenced by the displacement of Ni ions from the Ni layers to the Li planes as the content in lithium is reduced over a certain value. Recently, solid solutions such as LiNi_xCo_1−xO₂ have been proposed to offer a compromise between stability, cost and capacity. In this work we have studied LiNi_0.5Co_0.5O₂ prepared by the Complex Sol-Gel Process (CSGP). The advantage of this procedure toward the solid-state process is the high homogeneity in composition and in particle dimension of the synthesized compounds. The samples have been characterized electrochemically using chronopotentiometric, voltammetric and impedance measurements in liquid electrolyte. The results indicates that CSGP-synthesized LiNi_0.5Co_0.5O₂ shows good cyclability (after 1000 cycles about 2/3 of the initial capacity can still be cycled) only if the anodic potential is limited to about 4.2 V. The quite low values of the specific capacity (∼70 mAh/g at C/1 charge-discharge rate) can be justified by the non-complete calcination reaction, as suggested by X-ray measurements. Kinetic properties have been evaluated by Electrochemical Impedance Spectroscopy measurements, which have shown quite high values for the lithium chemical diffusion coefficient (10⁻⁷÷10⁻⁸ cm²s⁻¹) and its unexpected decrease as deintercalation proceeds from x=0.5 in LiNi_0.5Co_0.5O₂. Paper presented at the 4th Euroconference on Solid State Ionics, Renvyle, Galway, Ireland, Sept. 13–19, 1997     

Structural and electrochemical characterization of nickel hydroxide obtained by the new synthesis route of electrodialysis. a comparison with spherical β-Ni(OH)2

Both structural and electrochemical properties of non-doped nickel hydroxide produced by a new synthesis route of electrodialysis are investigated. A comparison with two spherical β-type Ni(OH)₂ is made. Structural characterization is carried out by X-ray diffraction, vibrational spectroscopy and thermal analysis. Electrochemical properties are studied by cyclic voltammetric and chronoamperometric experiments. The material obtained by electrodialysis is found to have a highly defective structure, which corresponds to a complex electrochemical behavior. More particlarly, it is shown that this new nickel hydroxide is more stable regarding the β → γ transformation. Project financed by the E.U. under the Brite Euram program (#BRPR-CT97-0515) Paper presented at the 6th Euroconference on Solid State Ionics, Sept. 12–19, 1999, Cetraro, Calabria, Italy     

Structural and electrochemical properties of LiNi1/3Co1/3Mn1/3O2 material prepared by a two-step synthesis via oxalate precursor

LiNi_1/3Co_1/3Mn_1/3O₂ (LNMCO) powders were formed by a two-step synthesis including preparation of an oxalate precursor by ??chimie douce?? followed by a solid-state reaction with lithium hydroxide. The product was characterized by TG-DTA, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR), Raman spectroscopy, electron spin resonance (ESR), and SQUID magnetometry. XRD data revealed well-crystallized layered LNMCO with ??-NaFeO₂-type structure (R-3?m space group). Morphology studied by SEM and TEM shows submicronic particles of 400?C800?nm with a tendency to agglomerate. The local structure investigated by vibrational spectroscopy (FTIR, Raman), ESR, and SQUID measurements confirms the well-crystallized lattice with a cation disorder of 2.6% Ni²⁺ ions in Li(3b) sites. Electrochemical tests were carried out in the potential range 2.5?C4.5?V vs. lithium metal on samples heated at 900?°C for 12?h. Initial discharge capacity is 154 mAh/g at C/5, while a capacity of 82 mAh/g is still delivered at 10 C by the two-step synthesized LiNi_1/3Co_1/3Mn_1/3O₂ as cathode material.     

Effect of nickel catalyst on physicochemical properties of carbon xerogels as electrode materials for supercapacitor

Carbon xerogels and Ni-doped carbon xerogels prepared by the sol-gel polymerization were examined to reveal the effect of metallic nickel incorporated in carbon matrix on the physicochemical properties of carbon xerogels and their electrochemical performance for supercapacitor electrode in aqueous 6 M KOH solution. As shown by XRD and XPS measurements, the decomposition of nickel precursor in carbon matrix led to the creation of well-crystalline particles of metallic nickel which gave rise to the changes in the morphology, chemical and porous structure of carbon xerogels. Due to the modification of porous structure the surface area increased from 595 m²/g via 632 m²/g up to 660 m²/g for carbon xerogel, 7 wt% and 10 wt% Ni-doped composites, respectively. The enhancement of the surface area occurred along with diminishing the BJH average pore diameter. The value for nickel free xerogel amounted to 11.35 nm, whereas the value of 5.71 nm was measured for 10 wt% Ni xerogel. The changes in the porous and chemical structure created during the formation of carbon-nickel composites as well as the pseudo-capacitive effects arising from the redox reaction of nickel particles present in carbon matrix brought about a significant improvement of electrode capacitance. Electrochemical measurements showed that in comparison with capacitances measured for nickel free electrode (82.1 F/g calculated using the cyclic voltammetry and 88.8 F/g calculated using the galvanostatic charge/discharge method), the respective capacitances for 10 wt% Ni-doped carbon xerogel increased up to 103.0 F/g and 103.4 F/g. These values correspond to 25 and 16% improvement, respectively.     

Studies on influence of zinc immersion and fluoride on nickel electroplating on magnesium alloy AZ91D

The effect of zinc immersion and the role of fluoride in nickel plating bath were mainly investigated in nickel electroplating on magnesium alloy AZ91D. The state of zinc immersion, the composition of zinc film and the role of fluoride in nickel plating bath were explored from the curves of open circuit potential (OCP) and potentiodynamic polarization, the images of scanning electron microscopy (SEM) and the patterns of energy dispersive X-ray (EDX). Results show that the optimum zinc film mixing small amount of Mg(OH)₂ and MgF₂ is obtained by zinc immersion for 30-90 s. The corrosion potential of magnesium alloy substrate attached zinc film will be increased in nickel plating bath and the quantity of MgF₂ sandwiched between magnesium alloy substrate and nickel coating will be reduced, which contributed to produce nickel coating with good performance. Fluoride in nickel plating bath serves as an activator of nickel anodic dissolution and corrosion inhibitor of magnesium alloy substrate. 1.0-1.5 mol dm⁻³ of F⁻ is the optimum concentration range for dissolving nickel anode and protecting magnesium alloy substrate from over-corrosion in nickel plating bath. The nickel coating with good adhesion and high corrosion resistance on magnesium alloy AZ91D is obtained by the developed process of nickel electroplating. This nickel layer can be used as the rendering coating for further plating on magnesium alloys.     

Synthesis of nanofiber-composed dandelion-like CoNiAl triple hydroxide as an electrode material for high-performance supercapacitor

In this work, CoNiAl triple hydroxide with nanofiber-composed dandelion-like morphology was synthesized on nickel foam by a hydrothermal route. This delicate nanostructure was initiated from the rolling up of hydroxide nanosheets. The hierarchical nanostructure and optimized molar ratio of Co, Ni, and Al guarantees the high electrochemical performance of obtained samples. The maximum specific capacitance of 2,791 F g^?1 for the as-prepared CoNiAl hydroxides was achieved at scan rate of 5 mV s^?1 in 3 M KOH aqueous solution. The capacitance of material still remained 85 % after 2,000 charge–discharge cycles. These results demonstrated that the as-prepared CoNiAl triple hydroxide can be applied as a high-performance electrode material for supercapacitor.     

In situ μ-Raman spectroscopy study of an isolated micrometer-size pseudo-single crystal of β-H2NiO2 under electrochemical operation

The response of micrometric pseudo-single crystals of β-H₂NiO₂, deposited on an Au substrate and submitted to high rate charge/discharge cycling under controlled current conditions, is studied by in situ μ-Raman spectroscopy. The intensities of the Raman background and of the hydroxyl stretching band are used to probe in time the single-particle surface and bulk oxidation states respectively. Results, obtained in the absence of electrical binders and chemical dopants, substantiate previous electrochemical investigations suggesting that the occurrence of the nickel electrode activation process is related to the formation of a thin surface limiting layer hindering the active material capacity to store and deliver energy. The feasibility of in situ μ-Raman spectroscopy on nickel hydroxide single particles submitted to electrochemical operation is demonstrated for the first time.     

Electrochromic and electrochemical properties of amorphous porous nickel hydroxide thin films

Nickel hydroxide films were prepared using the chemical bath deposition (CBD) technique. The amorphous nature of the films was confirmed by X-ray diffraction measurements. X-ray photoelectron spectroscopy (XPS) measurements showed that the films exhibited nickel hydroxide nature. The porosity of the films was studied using optical measurements. The electrochromic properties of the porous nickel hydroxide layers were investigated, using cyclic voltammetry, chronoamperometry, in situ transmittance, UV-vis spectroscopy, and impedance spectroscopy. The change in the optical density (ΔOD) was found to be 0.79 for the as-deposited nickel hydroxide films, whereas it is 0.53 and 0.50 for the films annealed at 150 °C and 200 °C, respectively. The in situ transmittance and chronoamperometry curves revealed that the annealed films had a very fast colouration (t_c < 290 ms) and decolouration (t_b < 130 ms). The measured colouration efficiencies range between 30 and 40 cm²/C. The impedance measurements revealed the faster colouration and good electrochromic properties for the annealed nickel hydroxide films.     

Facile synthesis and characterization of high-performance NiMoO<Subscript>4</Subscript> · <Emphasis Type="Italic">x</Emphasis>H<Subscript>2</Subscript>O nanorods electrode material for supercapacitors

One-dimensional NiMoO₄ · xH₂O nanorods were synthesized by a facile template-free hydrothermal method as a potential electrode material for supercapacitors. The influences of reaction temperature, reaction time, and nickel source on the properties of resultant samples were investigated. Electrochemical data reveal that the as-synthesized one-dimensional NiMoO₄ · xH₂O nanorod superstructures can deliver a remarkable specific capacitance (SC) of 1131 F g^?1 at a current density of 1 A g^?1 and remain as high as 914 F g^?1 at 10 A g^?1 in a 6 M KOH aqueous solution. Moreover, there is only 6.2 % loss of the maximum SC after 1000 continuous charge–discharge cycles at the high current density of 10 A g^?1. Such outstanding electrochemical performance may be owing to the unique one-dimensional hierarchical structures, which can facilitate the electrolyte ions and electrons to easily contact the NiMoO₄ nanorod building blocks and then allow for sufficient faradaic reactions to take place, even at high current densities.     

Structural and electrochemical properties of layered lithium nitridocuprates Li3 − xCuxN

We report a systematic study of the layered lithium nitridocuprates Li_3 ? xCu_xN with 0.1 ≤ x ≤ 0.39. The structural data obtained from experimental XRD patterns, Rietveld refinements and unit cell parameters calculation vs x, indicate that copper (I) substitute interlayer lithium ions in the parent nitride Li₃N to form the Li_3 ? xCu_xN compound without any Li vacancy in the Li₂N^? layer. Electrochemical results report Li insertion into the corresponding layered structures cannot take place in the 1.2/0.02 V voltage range as in the case of lithium into nitridonickelates and nitridocobaltates. However, in the initial charge process of Li_3 ? xCu_xN at 1.4 V leading to a specific capacity higher than 1000 mA h/g, the oxidation of copper and nitride ions is probably involved inducing a strong structural disordering process. As a consequence a new rechargeable electrochemical system characterized by discharge–charge potential of ≈ 0.3 V/1.2 V appears from the second cycle. Cycling experiments 0.02 V voltage/0.02 V range induce a complete destruction of the layered host lattice and the presence of Cu₃N in the charge state suggests a conversion reaction. The capacity recovered in the 1.4/0.02 V range practically stabilizes around 500 mA h/g after 20 cycles.