Mesoscopic patterns of block and graft copolymers in condensed systems

Equilibrium structures of two kinds of two‐component copolymers with equivalent chemical contents but with different chain architectures in bulk were compared. They are BAB triblock copolymers and AB₂ star‐branched graft copolymers. These copolymers have been confirmed to show quite different morphological change with composition. Deformation manner of B block chains of lamellar microphase‐separated BAB triblock copolymers depend on B contents, however, the volumes of the deformed coils are always kept constant to have those of the unperturbed chains irrespective of their architectures. The observed polystyrene/poly(2‐vinylpyridine) interfacial thickness is fairly thin though it is much thicker than the theoretically‐predicted one.     

Synthesis and characterization of well‐defined ABC‐type triblock copolymers via atom transfer radical polymerization and stable free‐radical polymerization

An asymmetric difunctional initiator 2‐phenyl‐2‐[(2,2,6,6 tetramethylpiperidino)oxy] ethyl 2‐bromo propanoate ( 1 ) was used for the synthesis of ABC‐type methyl methacrylate (MMA)‐tert‐butylacrylate (tBA)‐styrene (St) triblock copolymers via a combination of atom transfer radical polymerization (ATRP) and stable free‐radical polymerization (SFRP). The ATRP‐ATRP‐SFRP or SFRP‐ATRP‐ATRP route led to ABC‐type triblock copolymers with controlled molecular weight and moderate polydispersity (M_w/M_n < 1.35). The block copolymers were characterized by gel permeation chromatography and ¹H NMR. The retaining chain‐end functionality and the applying halide exchange afforded high blocking efficiency as well as maintained control over entire routes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2025–2032, 2002     

Morphology of ABC triblock copolymer/homopolymer blend systems

Morphological variations of ABC triblock copolymers through the blending of B or A/C homopolymers, all with short chain lengths, were studied experimentally. The samples were symmetric ISP triblock copolymers, where I, S, and P denote polyisoprene, polystyrene, and poly(2‐vinylpyridine), and component homopolymers. Microphase‐separated structures of the solvent‐cast films were observed with transmission electron microscopy and small‐angle X‐ray scattering. For an ISP/S system, the lattice constant of the tricontinuous gyroid structure (G‐structure) increased with an increase in the volume fraction of S (?_s) if the amount of added homopolymer was small, but it reached a certain limit, reflecting the fact that the midblock chain had a limit for chain stretching. For I/ISP/P blends, on the contrary, the lattice constant of the G‐structure continued increasing with decreasing ?_s. This result shows that the I and P domains did not have a limit for chain stretching because the two end blocks had free ends. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1135–1141, 2002     

Stimuli‐responsive ABC triblock copolymers by sequential living cationic copolymerization: Multistage self‐assemblies through micellization to open association

Stimuli‐responsive ABC triblock copolymers with three segments with different phase‐separation temperatures were synthesized via sequential living cationic copolymerization. The triblock copolymers exhibited sensitive thermally induced physical gelation (open association) through the formation of micelles. For example, an aqueous solution of EOVE₂₀₀‐b‐MOVE₂₀₀‐b‐EOEOVE₂₀₀ [where EOVE is 2‐ethoxyethyl vinyl ether, MOVE is 2‐methoxethyl vinyl ether and EOEOVE is 2‐(2‐ethoxy)ethoxyethyl vinyl ether; the order of the phase‐separation temperatures was poly(EOVE) (20 °C) < poly(EOEOVE) (41 °C) < poly(MOVE) (70 °C)] underwent multiple reversible transitions from sol (<20 °C) to micellization (20–41 °C) to physical gelation (physical crosslinking, 41–64 °C) and, finally, to precipitation (>64 °C). At 41–64 °C, the physical gel became stiffer than similar diblock or ABA triblock copolymers of the same molecular weight. Furthermore, the ABC triblock copolymers exhibited Weissenberg effects in semidilute aqueous solutions. In sharp contrast, another ABC triblock copolymer with a different arrangement, EOVE₂₀₀‐b‐EOEOVE₂₀₀‐b‐MOVE₂₀₀, scarcely exhibited any increase in viscosity above 41 °C. The temperatures of micelle formation and physical gelation corresponded to the phase‐separation temperatures of the segment types in the ABC triblock copolymer. No second‐stage association was observed for AB and ABA block copolymers with the same thermosensitive segments found in their ABC counterparts. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2601–2611, 2004     

Effect of architecture on the tensile properties of triblock copolymers in a lamellar phase.

We have used self-consistent field theory to calculate the tensile moduli of triblock copolymers in lamellar microstructures prepared from linear and star architectures. The extensional moduli K(33) are the main contributors to the tensile moduli, and the contribution of K(U)33 (the internal energy contribution to K(33)) is the main component of the value of K(33). We find that the tensile moduli of ABC three-miktoarm star terpolymers are smaller than those of ABC linear triblock copolymers having identical components, presumably for two main reasons. First, for the ABC three-miktoarm star terpolymers, the contributions of K(U)33 are larger than those of the linear triblock copolymers; we attribute this phenomenon to the star terpolymers having smaller lamellar domain sizes at equilibrium relative to those of the linear triblock copolymers. Second, conformational entropies play an important role in affecting the tensile moduli, mainly because of the different degrees of freedom of the various chains. In contrast, the shear moduli contribute negligibly to the tensile moduli.     

Investigations on liquid crystalline partially fluorinated alkyl and succinimidyl benzoates

The synthesis and mesophase properties of partially fluorinated alkoxy‐substituted benzoic alkyl and succinimidyl (NHS) esters with one, two and three perfluoroalkyl alkoxy chains are reported. The mesophases were studied using differential scanning calorimetry (DSC), polarizing optical microscopy and X‐ray diffraction of non‐oriented samples. The SmA phases of the one‐chain methyl esters are monotropic, while those of the one‐chain NHS esters are enantiotropic. The more wedge‐shaped two‐ and three‐chain alkyl esters do not form mesophases, whereas the succinimidyl analogues exhibit hexagonal columnar phases. Their enhanced mesophase stability is caused by the higher polarity of the succinimidyl ring with respect to the alkyl ester groups. Aggregation of the dipolar succinimidyl groups, together with the microsegregation of the lipophilic and fluorophilic segments of the partially fluorinated alkoxy chains, is assumed to lead to a threefold structured morphology in both the SmA and the Col_h phases. This threefold structuring can be regarded as analogous to known morphologies of ABC triblock copolymers.     

Azobenzene‐Containing Block Copolymers as Light‐Induced Reworkable Adhesives: Effects of Molecular Weight,Composition, and Block Copolymer Architectures on the Adhesive Properties

We previously reported that ABA‐type triblock copolymers with azobenzene‐containing terminal blocks can be utilized as a light‐induced reworkable adhesive that enables repeatable bonding and debonding on demand. The reworkability was based on the photoisomerization of the azobenzene moiety and concomitant softening and hardening of the azo blocks. Our aim in this study is to investigate the effect of the composition, molecular weight, and block copolymer architectures on the reworkable adhesive properties. For this purpose, we prepared AB diblock, ABA triblock, and 4‐arm (AB)₄ star‐block copolymers consisting of polymethacrylates bearing an azobenzene moiety (A block) and 2‐ethylhexyl (B block) side chains and performed adhesion tests by using these block copolymers. As a result, among the ABA block copolymers with varied compositions and molecular weights, the ABA triblock copolymers with an azo block content of about 50 wt % and relatively low molecular weight could achieve an appropriate balance between high adhesion strength and low residual adhesion strength upon UV irradiation. Furthermore, the 4‐arm star‐block structure not only enhances the adhesion strength, but also maintains low residual adhesion strength when exposed to UV irradiation. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 806–813     

Synthesis of α,ω‐di(iodo)PVC and of four‐arm star PVC with identical active chain ends by SET‐DTLRP of VC initiated with bifunctional and tetrafunctional initiators

Na₂S₂O₄‐catalyzed single‐electron transfer – degenerative chain transfer‐mediated living radical polymerization (SET‐DTLRP) of VC initiated with the bifunctional initiators 1,2‐bis(iodopropionyloxy)ethane, dimethyl 2,5‐diiodohexanedioate, and bis(2‐methoxyethyl)‐2,5‐diiodohexanedioate as well as the tetrafunctional initiator pentaerythritol tetrakis(2‐iodopropionate) is reported. This SET‐DTLRP was performed in water at ambient temperature in the presence of polyvinyl alcohol and hydroxypropyl methylcellulose surfactants and provides methods for the synthesis of α,ω‐di(iodo)PVC with two identical active chain ends and of four‐arm star PVC with four identical active chain ends. These difunctional and tetrafunctional derivatives of PVC are also macroinitiators for the synthesis of ABA triblock copolymers and four‐arm star block copolymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 635–652, 2009     

A Molecular Dynamics Simulation on the Self‐Assembly of ABC Triblock Copolymers, 1. Effects of Block Composition in Symmetric Triblock Copolymers

The self‐assembly of ABC triblock copolymers in the microphase‐separated state is investigated using an isothermal‐isobaric molecular dynamics simulation. For the validation of our simulation scheme, ABA triblock copolymers are also simulated. We examine the effect of the composition (f_B) of symmetric triblock copolymers on the morphology realized in these copolymers, keeping other parameters fixed. For ABA triblock copolymers, the transition from lamellar to cylindrical morphologies is observed with increasing the composition from f_B = 0.5 to f_B = 0.75, and such behavior is supported by calculation results of scattering patterns. These simulated results agree well with experimental and theoretical ones, validating our simulation method. More complex structures are predicted for ABC triblock copolymers. If midblock B is the minor component, its structures are changed from lamellar, cylindrical, to spherical morphology at the interface between A/C lamellae as f_B decreases. For ABC triblock copolymers with the midblock B as the major component, the morphology of end blocks in the matrix composed of the midblock is changed from tricontinuous to spherical structures as f_B increases.     

Synthesis and characterization of side‐chain liquid crystalline ABC triblock copolymers with p‐methoxyazobenzene moieties by atom transfer radical polymerization

A series of novel side‐chain liquid crystalline ABC triblock copolymers composed of poly(ethylene oxide) (PEO), polystyrene (PS), and poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] (PMMAZO) were synthesized by atom transfer radical polymerization (ATRP) using CuBr/1,1,4,7,7‐pentamethyldiethylenetriamine (PMDETA) as a catalyst system. First, the bromine‐terminated diblock copolymer poly(ethylene oxide)‐block‐polystyrene (PEO‐PS‐Br) was prepared by the ATRP of styrene initiated with the macro‐initiator PEO‐Br, which was obtained from the esterification of PEO and 2‐bromo‐2‐methylpropionyl bromide. An azobenzene‐containing block of PMMAZO with different molecular weights was then introduced into the diblock copolymer by a second ATRP to synthesize the novel side‐chain liquid crystalline ABC triblock copolymer poly(ethylene oxide)‐block‐polystyrene‐block‐poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] (PEO‐PS‐PMMAZO). These block copolymers were characterized using proton nuclear magnetic resonance (¹H NMR) and gel permeation chromatograph (GPC). Their thermotropic phase behaviors were investigated using differential scanning calorimetry (DSC) and polarized optical microscope (POM). These triblock copolymers exhibited a smectic phase and a nematic phase over a relatively wide temperature range. At the same time, the photoresponsive properties of these triblock copolymers in chloroform solution were preliminarily studied. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4442–4450, 2008     

Controlled ring‐opening polymerization of L‐lactide and 1,5‐dioxepan‐2‐one forming a triblock copolymer

Novel elastomeric A‐B‐A triblock copolymers were successfully synthesized in a new two‐step process: controlled ring‐opening polymerization of the cyclic ether–ester 1,5‐dioxepan‐2‐one as the amorphous middle block (B‐block) followed by addition and polymerization of the two semicrystalline L ‐lactide blocks (A‐block). A 1,1,6,6‐tetra‐n‐butyl‐1,6‐distanna‐2,5,7,10‐tetraoxacyclodecane initiator system was utilized and the reaction was performed in chloroform at 60 °C. A good control of the synthesis was obtained, resulting in well defined triblock copolymers. The molecular weight and chemical composition were easily adjusted by the monomer‐to‐initiator ratio. The triblock copolymers formed exhibited semicrystallinity up to a content of 1,5‐dioxepan‐2‐one as high as 89% as determined by differential scanning calorimetry. WAXS investigation of the triblock copolymers showed a crystal structure similar to that of the pure poly(L ‐lactide). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1774–1784, 2000     

Synthesis and characterization of well‐defined diblock and triblock copolymers of poly(N‐isopropylacrylamide) and poly(ethylene oxide)

Well‐defined diblock and triblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly(ethylene oxide) (PEO) were successfully synthesized through the reversible addition–fragmentation chain transfer polymerization of N‐isopropylacrylamide (NIPAM) with PEO capped with one or two dithiobenzoyl groups as a macrotransfer agent. ¹H NMR, Fourier transform infrared, and gel permeation chromatography instruments were used to characterize the block copolymers obtained. The results showed that the diblock and triblock copolymers had well‐defined structures and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.2), and the molecular weight of the PNIPAM block in the diblock and triblock copolymers could be controlled by the initial molar ratio of NIPAM to dithiobenzoate‐terminated PEO and the NIPAM conversion. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4873–4881, 2004     

Synthesis of nylon‐6 triblock copolymers with bifunctional polymeric activators

ABA‐type copolymers were synthesized by the anionic polymerization of hexanelactam with the sodium salt of hexanelactam as an initiator and amino‐terminated polytetrahydrofuran telechelic functionalized with diisocyanates. Two types of diisocyanates, hexamethylene diisocyanate (1,6‐diisocyanatohexane) and isophorone diisocyanate (IF; 5‐isocyanato‐1‐isocyanatomethyl‐1,3,3‐trimethylcyclohexane), were used as precursors for polymeric activators (PACs). IF was used for the first time. It was proven that the PACs were incorporated as soft, flexible midblocks in the chains of hard nylon‐6 segments. The polymers were isolated and characterized with various spectroscopic techniques. The effects of the central PAC block (according to the type, molecular weight, and content) and the polymerization conditions on the kinetics, activation energies, molecular weights, and structures of the triblock copolymers were investigated. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4154–4164, 2000     

Morphology and mechanical properties of binary triblock copolymer blends

The influence of the morphology on the mechanical properties of binary styrene–butadiene (SB) triblock copolymer blends of a thermoplastic block copolymer and a thermoplastic elastomer (TPE) with different molecular architectures was studied with bulk samples prepared from toluene. Both block copolymers contained SB random copolymer middle blocks, that is, the block sequence S–SB–S. The two miscible triblock copolymers were combined to create a TPE with increased tensile strength without a change in their elasticity. The changes in the equilibrium morphology of the miscible triblock copolymer blends as a function of the TPE content (lamellae, bicontinuous morphology, hexagonal cylinders, and worms) resulted in a novel morphology–property correlation: (1) the strain at break and Young's modulus of blends with about 20 wt % TPE were larger than those of the pure thermoplastic triblock copolymer; (2) at the transition from bicontinuous structures to hexagonal structures (～35 wt % TPE), a change in the mechanical properties from thermoplastic to elastomeric was observed; and (3) in the full range of wormlike and hexagonal morphology (60–100 wt % TPE), elastomeric properties were observed, the strength greatly increasing and high‐strength elastomers resulting. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 429–438, 2005     

Block copolymers with Zwitterionic groups at specific sites: Synthesis and aggregation behavior in dilute solutions

Well‐defined linear diblock and triblock copolymers of styrene and isoprene, nearly symmetric in composition, with one or two sulfobetaine associogenic groups at the ends of the polymer chain or the junction points between blocks, were synthesized by anionic polymerization high‐vacuum techniques. The synthetic strategy used the combined initiation of polymerization with 3‐dimethylaminopropyllithium, living end‐capping with 1‐(4‐dimethylaminophenyl)‐1‐phenylethylene, and postpolymerization reaction with cyclopropanesultone. The association behavior of these macromolecules in dilute solutions in the nonpolar solvent CCl₄, good for both blocks, was studied by a number of methods, including static and dynamic light scattering and viscometry. The number and position of the associogenic groups dramatically influenced the association behavior of these model block copolymers. The end‐functionalized samples formed larger aggregates than the junction‐point‐functionalized ones. The difference was attributed to stronger excluded volume effects when the zwitterion group was located within the chain than when the group was at the chain end(s). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3791–3801, 2000     

Development of organotellurium‐mediated and organostibine‐mediated living radical polymerization reactions

Organotellurium‐mediated living radical polymerizations (TERPs) and organostibine‐mediated living radical polymerizations (SBRPs) provide well‐defined polymers with a variety of polar functional groups via degenerative chain‐transfer polymerization. The high controllability of these polymerizations can be attributed to the rapid degenerative‐transfer process between the polymer‐end radicals and corresponding dormant species. The versatility of the methods allows the synthesis of AB diblock, ABA triblock, and ABC triblock copolymers by the successive addition of different monomers. This review summarizes the current status of TERP and SBRP. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1–12, 2006     

Stepwise Light‐Induced Dual Compaction of Single‐Chain Nanoparticles

A photochemical strategy for the sequential dual compaction of single polymer chains is introduced. Two photoreactive methacrylates, with side chains bearing either a phenacyl sulfide (PS) or an α‐methylbenzaldehyde (photoenol, PE) moiety, are selectively incorporated by one‐pot iterative reversible‐addition fragmentation chain transfer copolymerization into the outer blocks of a well‐defined poly(methyl methacrylate) based ABC triblock copolymer possessing a nonfunctional spacer block (M _n = 23 400 g mol⁻¹, Đ = 1.2; ≈15 units of each photoreactive moieties of each type) as well as in model statistical copolymers bearing only one type of photoreactive unit. Upon UVA irradiation, PS and PE lead to highly reactive thioaldehydes and o‐quinodimethanes, which rapidly react with dithiol and diacrylate linkers, respectively. The monomerfunctional copolymers are employed to establish the conditions for controlled intramolecular photo‐crosslinking, which are subsequently applied to the bifunctional triblock copolymer. All compaction/folding experiments are monitored by size‐exclusion chromatography and dynamic light scattering. The dual compaction consists of two events of dissimilar amplitude: the first folding step reveals a large reduction in hydrodynamic diameters, while the second compaction lead to a far less pronounced reduction of the single‐chain nanoparticles size, consistent with the reduced degrees of freedom available after the first covalent compaction step.     

Synthesis and characterization of biodegradable triblock copolymers based on bacterial poly[(R)‐3‐hydroxybutyrate] by atom transfer radical polymerization

Biodegradable poly(tert‐butyl acrylate)–poly[(R)‐3‐hydroxybutyrate]–poly (tert‐butyl acrylate) triblock copolymers based on bacterial poly[(R)‐3‐hydroxybutyrate] (PHB) were synthesized by atom transfer radical polymerization. The chain architectures of the triblock copolymers were confirmed by ¹H NMR and ¹³C NMR spectra. Gel permeation chromatography analysis was used to estimate the molecular weight characteristics and lengths of the PHB and poly(tert‐butyl acrylate) blocks of the copolymers. The thermal properties of the copolymers were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA showed that the triblock copolymers underwent stepwise thermal degradation and had better thermal stability than their respective homopolymers, whereas DSC analyses showed that a microphase‐separation structure was formed only in the triblock copolymers with the longer PHB block. As a similar result, from wide‐angle X‐ray diffraction experimentation, the crystalline phase of PHB could not be seen evidently in the triblock copolymers with the shorter PHB block. The enzymatic hydrolysis of the copolymer films was carried at 37 °C and pH 7.4 in a potassium phosphate buffer with an extracellular PHB depolymerase from Penicillum sp. The biodegradability of the triblock copolymers increased with an increase in the PHB block content. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4857–4869, 2005     

Synthesis and characterization of block copolymers containing poly(di(ethylene glycol) 2‐ethylhexyl ether acrylate) by reversible addition–fragmentation chain transfer polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization has emerged as one of the important living radical polymerization techniques. Herein, we report the polymerization of di(ethylene glycol) 2‐ethylhexyl ether acrylate (DEHEA), a commercially‐available monomer consisting of an amphiphilic side chain, via RAFT by using bis(2‐propionic acid) trithiocarbonate as the chain transfer agent (CTA) and AIBN as the radical initiator, at 70 °C. The kinetics of DEHEA polymerization was also evaluated. Synthesis of well‐defined ABA triblock copolymers consisting of poly(tert‐butyl acrylate) (PtBA) or poly(octadecyl acrylate) (PODA) middle blocks were prepared from a PDEHEA macroCTA. By starting from a PtBA macroCTA, a BAB triblock copolymer with PDEHEA as the middle block was also readily prepared. These amphiphilic block copolymers with PDEHEA segments bearing unique amphiphilic side chains could potentially be used as the precursor components for construction of self‐assembled nanostructures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5420–5430, 2007     

The influence of solution‐state conditions and stirring rate on the assembly of poly(acrylic acid)‐containing amphiphilic triblock copolymers with multi‐amines

In the effort towards making nanoscale objects and assemblies feasible for use as functional materials, it is imperative to obtain control over the fundamental architectures and essential to understand what experimental conditions cause the manifestation of specific morphologies. A number of factors are known to influence the shape during the self‐assembly of amphiphilic block copolymers in solution, including solvent composition, polymer length, hydrophobicity versus hydrophilicity, as well as the addition of additives that can interact with segments of the block copolymers. This research, focused on developing an understanding of the micellar architectures accessed by the amphiphilic triblock copolymer of acrylic acid, methyl acrylate, and styrene, PAA₈₅‐b‐PMA₄₀‐b‐PS₃₅, as a function of the stirring rate, together with other factors, when undergoing coassembly with ethylenediamine or diethylenetriamine in water/tetrahydrofuran solutions. The work demonstrates that the rate at which the polymer solution was stirred impacts the shape of the solution‐state assemblies formed by the triblock copolymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010