聚天冬氨酸的合成研究

以L-天冬氨酸为原料,磷酸为催化剂,在不同溶剂中进行缩聚反应,合成中间体聚丁二酰亚胺(PSI),当混合溶剂为m三甲苯／m环丁砜=7／3时,可得到较高分子量的PSI。当催化剂与单体的质量比为0．14时,分子量达到最大值。将PSI碱解得到聚天冬氨酸。     

Melt polycondensation of L‐lactic acid with Sn(II) catalysts activated by various proton acids: A direct manufacturing route to high molecular weight Poly(L‐lactic acid)

Poly(L ‐lactic acid) (PLLA) was produced by the melt polycondensation of L ‐lactic acid. For the optimization of the reaction conditions, various catalyst systems were examined at different temperature and reaction times. It was discovered that Sn(II) catalysts activated by various proton acids can produce high molecular weight PLLA [weight‐average molecular weight (M_w ) ≥ 100,000] in a relatively short reaction time (≤15 h) compared with simple Sn(II)‐based catalysts (SnO, SnCl₂ · 2H₂O), which produce PLLA with an M_w of less than 30,000 after 20 h. The new catalyst system is also superior to the conventional systems in regard to racemization and discoloration of the resultant polymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1673–1679, 2000     

Synthesis and properties of multiblock copolymers consisting of poly(L‐lactic acid) and poly(oxypropylene‐ co‐oxyethylene) prepared by direct polycondensation

A multiblock copoly(ester–ether) consisting of poly(l ‐lactic acid) (PLLA) and poly(oxypropylene‐co‐oxyethylene) (PN) was prepared and characterized. Preparation was done via the solution polycondensation of a thermal oligocondensate of l ‐lactic acid, a commercially available telechelic polyether (PN: Pluronic‐F68), and dodecanedioic acid as a carboxyl/hydroxyl adjusting agent. When stannous oxide was used as the catalyst, the molecular weight of the resultant PLLA/PN block copolymers became very high (even with a high PN content) under optimized reaction conditions. The refluxing of diphenyl ether (solvent) at reduced pressure allowed the efficient removal of the condensed water from the reaction system and the feed‐back of the intermediately formed l ‐lactide at the same time in order to successfully bring about a high degree of condensation. The copolymer films obtained by solution casting became more flexible with the increasing PN content as soft segments. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1513–1521, 1999     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Swelling kinetics of poly(aspartic acid)/poly(acrylic acid) semi‐interpenetrating polymer network hydrogels in urea solutions

Semi‐interpenetrating network (semi‐IPN) hydrogels, composed of poly(aspartic acid) (PAsp) and poly(acrylic acid) (PAAc) with various ratios of PAsp to AAc, were prepared. In this work, swelling kinetics was investigated through calculating some parameters. The swelling ratios were measured at room temperature, using urea solutions as liquids to be absorbed. Compared to in deionized water, the hydrogels showed larger swelling ratios in urea solutions, which might be attributed to the chemical composition of urea. The equilibrium swelling ratio could achieve 600 g/g, and the equilibrium urea/water contents were more than 0.99. The diffusion exponents were between 0.5 and 0.7, suggesting that the solvent transport into the hydrogel was dominated by both diffusion and relaxation controlled systems. Therefore, the PAsp/PAAc semi‐IPN hydrogels were appropriate to carry substances in a urea/water environment for pharmaceutical, agricultural, environmental, and biomedical applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 666–671, 2010     

Synthesis of high‐molecular‐weight aliphatic–aromatic copolyesters from poly(ethylene‐co‐1,6‐hexene terephthalate) and poly(L‐lactic acid) by chain extension

A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, ¹H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than M_w = 3 × 10⁵ g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009     

Synthesis of poly(ester amide)s with lateral groups from a bulk polycondensation reaction with formation of sodium chloride salts

Poly(ester amide)s with a regular sequence and derived from diamine, dicarboxylic acid, and glycolic acid units can be easily synthesized by using a thermal polycondensation method based on the formation of metal halide salts as a driving force. These new poly(ester amide)s have tuneable properties depending on the number of methylene groups and constitute a group of materials with potential interest as biodegradable materials in applications such as surgical sutures. The present work reveals that the proposed synthesis can also be applied when esters of L ‐lysine are used as a diamine unit since no secondary reactions such as transesterification occur under the required polymerization conditions. The possibility of linking compounds with pharmacological activity to the carboxylic acid groups of lysine extends the interest of the referred materials, for example, as drug delivery systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 661–667, 2008     

Gas‐forming poly(ethylene glycol)‐b‐poly(L‐lactic acid) micelles

In this study, a novel drug‐carrying micelle composed of methoxy poly(ethylene glycol) (mPEG)‐b‐poly(L‐lactic acid) (PLLA) with gas‐forming carbonate linkage was fabricated. Here, the gas‐forming carbonate linkage was formed by the chemical coupling of the terminal hydroxyl group of the PLLA block and benzyl chloroformate (BC). mPEG‐b‐PLLA‐BC was self‐organized in aqueous solution: the PEG block on the hydrophilic outer shell and the PLLA‐BC block in the hydrophoboic innor core. The cleavage of carbonate linkage by hydrolysis and formation of carbon dioxide nanobubbles in the micellar core enabled an accelerated release of the encapsulated anticancer drug (doxorubicin: DOX) from the mPEG‐b‐PLLA‐BC micelles. The amount of drug (DOX) released from the mPEG‐b‐PLLA‐BC micelle was higher than that from the conventional mPEG‐b‐PLLA micelle, which allowed for increased in vitro toxicity against KB tumor cells. Copyright © 2013 John Wiley & Sons, Ltd.     

Selective transport of D,L‐tryptophan through poly(L‐glutamic acid) membranes

Permeability coefficients of D ‐ and L ‐tryptophan (D ‐, L ‐Trp) were estimated for poly(L ‐glutamic acid) (PLG) membranes immersed in aqueous ethanol. D ‐tryptophan was selectively transported (the maximum permeability ratio was 2.6) depending on the amount and the species of crosslinking agent, and on the composition of immersing solvent. It is suggested that hydrogen bonding between uncharged permeates and carboxyl and/or amide groups of PLG is an essential factor for the selective transport. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1035–1041, 1999     

Effect of PEO‐PPO‐PEO copolymer on the mechanical and thermal properties and morphological behavior of biodegradable poly (L‐lactic acid) (PLLA) and poly (butylene succinate‐co‐L‐lactate) (PBSL) blends

A blend of two biodegradable and semi‐crystalline polymers, poly (L‐lactic acid) (PLLA; 70 wt%) and poly (butylene succinate‐co‐L‐lactate) (PBSL; 30 wt%), was prepared in the presence of various polyethylene oxide‐polypropylene oxide‐polyethylene oxide (PEO‐PPO‐PEO) triblock copolymer contents (0.5, 1, 2 wt%). Mechanical, thermal properties, and Fourier transform infrared (FTIR) analysis of the blends were investigated. It was found that the addition of copolymer to PLLA/PBSL improved the fracture toughness of the blends as shown by mode I fracture energies. It was supported by morphological analysis where the brittle deformation behavior of PLLA changed to ductile deformation with the presence of elongated fibril structure in the blend with copolymer system. The glass transition temperature (T_g), melting temperature (T_m) of PLLA, and PBSL shift‐closed together indicated that some compatibility exists in the blends. In short, PEO‐PPO‐PEO could be used as compatibilizer to improve the toughness and compatibility of the PLLA/PBSL blends. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and characterization of amphiphilic block copolymer of polyphosphoester and poly(L‐lactic acid)

Aliphatic polyesters and polyphosphoesters (PPEs) have received much interest in medical applications due to their favorable biocompatibility and biodegradability. In this work, novel amphiphilic triblock copolymers of PPE and poly(L ‐lactic acid) (PLLA) with various compositions were synthesized and characterized. The blocky structure was confirmed by GPC analyses. These triblock copolymers formed micelles composed of hydrophobic PLLA core and hydrophilic PPE shell in aqueous solution. Critical micellization concentrations of these triblock copolymers were related to the polymer compositions. Incubation of micelles at neutral pH followed by GPC analyses revealed that these polymer micelles were hydrolysized and resulted in decreased molecular weights and small oligomers, whereas its degradation in basic and acid mediums was accelerated. MTT assay also demonstrated the biocompatibility against HEK293 cells. These biodegradable polymers are potential as drug carriers for biomedical application. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6425–6434, 2008     

Synthesis and characterization of multiblock copolymers based on L‐lactic acid,citric acid,and poly(ethylene glycol)

Because poly(L ‐lactic acid) (PLLA) is a biodegradable polyester with low immunogenicity and good biocompatibility, it is used as a biomaterial. However, hydrophobic PLLA does not have any reactive groups. Thus, its application is limited. To increase the hydrophilicity of PLLA and accelerate its degradation rate, functionalized pendant groups and blocks were introduced through copolymerization with citric acid and poly(ethylene glycol) (PEG), respectively. This article describes the synthesis and characterization of poly(L ‐lactic‐co‐citric acid) (PLCA)‐PLLA and PLCA‐PEG multiblock copolymers. The results indicated that the hydrolysis rate was enhanced, and the hydrophilicity was improved because of the incorporation of carboxyl groups in PLCA‐PLLA. The joining of the PEG block led to improved hydrophilicity of PLCA, and the degradation rate of PLCA‐PEG accelerated as compared with that of PLCA‐PLLA. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2073–2081, 2003     

Stereoblock poly(lactic acid): synthesis via solid-state polycondensation of a stereocomplexed mixture of poly(L-lactic acid) and poly(D-lactic acid)

Stereoblock poly(lactic acid) consisting of D- and L-lactate stereosequences can be successfully synthesized by solid-state polycondensation of a 1:1 mixture of poly(L-lactic acid) and poly(D-lactic acid). In the first step, melt-polycondensation of L- and D-lactic acids is conducted to synthesize poly(L-lactic acid) and poly(D-lactic acid) with a medium-molecular-weight, respectively. In the next step, these poly(L-lactic acid) and poly(D-lactic acid) are melt-blended in 1:1 ratio to allow formation of their stereocomplex. In the last step, this melt-blend is subjected to solid-state polycondensation at temperature where the dehydrative condensation is allowed to promote chain extension in the amorphous phase with the stereocomplex crystals preserved. Finally, stereoblock poly(lactic acid) having high-molecular-weight is obtained. The stereoblock poly(lactic acid) synthesized by this way shows a higher melting temperature in consequence of the controlled block lengths and the resulting higher-molecular-weight. The product characterization as well as the optimization of the polymerization conditions is described. Changes in M(w) of stereoblock poly(lactic acid) (sb-PLA) as a function of the reaction time.     

Synthesis and characterization of poly(vinyl alcohol)‐graft‐[poly(D,L‐lactide)/poly(D,L‐lactide‐co‐glycolide)] hydrogels

Poly(D ,L ‐lactide) and poly(D ,L ‐lactide‐co‐glycolide) with various composition and with one methacrylate and one carboxylate end group were synthesized and grafted onto poly(vinyl alcohol) (PVA) via the carboxylate group. The graft copolymers were crosslinked via the methacrylate groups using a free radical initiator. The polymer networks were characterized by means of NMR and studied qualitatively by means of IR spectroscopy. The influence of the glycolide content in the polyester grafts and of the number of ester units in the grafts on thermal properties and swellability were studied as well. The high swellability in water is characteristic of all hydrogels. Differential scanning calorimetry (DSC) showed a single glass transition temperature that occurs in the range between 51 and 69 °C. Thermogravimetric analysis (TGA) of the networks showed the main loss in weight in the temperature range between 290 and 370 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4536–4544, 2007     

Preparation of poly (L‐lactic acid) with aligned structures by unidirectional freezing

Honeycomb monolith structured porous poly (L‐lactic acid, PLA) was simply fabricated by employing a unidirectional freeze‐casting technique. Dimethyl sulfoxide (DMSO) was used as a solvent for PLA, and the solution was unidirectionally frozen. The DMSO was nucleated in the solution and was grown in the freezing direction. The PLA was solidified and structured with the DMSO crystal as a template. Then DMSO was leached by water, ethanol, or the mixture of them, and subsequently the porous PLA was dried by oven. It was found that the freeze‐casting protocol can significantly influence the morphological features such as the tube diameter and wall thickness of tube can be tuned by varying of PLA concentration, freezing temperature, and the nature of leaching solvent. Because DMSO has a special solubility of a number of polymers, this method may be a general way for designing and preparing aligned porous materials. Copyright © 2015 John Wiley & Sons, Ltd.     

Cancer‐associated pH‐responsive tetracopolymeric micelles composed of poly(ethylene glycol)‐b‐poly(L‐histidine)‐b‐poly(L‐lactic acid)‐b‐poly(ethylene glycol)

To create a novel vector for specifically delivering anticancer therapy to solid tumors, we used diafiltration to synthesize pH‐sensitive polymeric micelles. The micelles, formed from a tetrablock copolymer [poly(ethylene glycol)‐b‐poly(L ‐histidine)‐b‐poly(L ‐lactic acid)‐b‐poly(ethylene glycol)] consisted of a hydrophobic poly(L ‐histidine) (polyHis) and poly(L ‐lactic acid) (PLA) core and a hydrophilic poly(ethylene glycol) (PEG) shell, in which we encapsulated the model anticancer drug doxorubicin (DOX). The robust micelles exhibited a critical micellar concentration (CMC) of 2.1–3.5 µg/ml and an average size of 65–80 nm pH 7.4. Importantly, they showed a pH‐dependent micellar destabilization, due to the concurrent ionization of the polyHis and the rigidity of the PLA in the micellar core. In particular, the molecular weight of PLA block affected the ionization of the micellar core. Depending on the molecular weight of the PLA block, the micelles triggering released DOX at pH 6.8 (i.e. cancer acidic pH) or pH 6.4 (i.e. endosomal pH), making this system a useful tool for specifically treating solid cancers or delivering cytoplasmic cargo in vivo. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis of amphiphilic poly(para‐phenylene)s by Suzuki polycondensation

1,4‐Dibromobenzenes carrying nonpolar hexoxy and polar oligo(ethylene glycol) side chains were subjected to Suzuki polycondensation with a benzene‐1,4‐bisboronic acid ester to produce high‐molar‐mass poly(para‐phenylene)s. The molar masses were determined with size exclusion chromatography with conventional polystyrene and universal calibration. These novel amphiphilically equipped rigid‐rod polymers have the potential to segregate lengthwise into polar and nonpolar domains, a property that has only rarely been described, and promise to exhibit novel interesting supramolecular properties. The oligo(ethylene gylcol) side chains terminate with a silyl‐protected alcohol group, and its deprotection on the polymer was proven to proceed quantitatively. This not only led to a further polarity increase but allows us to attach even more polar (e.g., charged) units in future projects. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2879–2889, 2003     

Novel temperature‐ and pH‐responsive graft copolymers composed of poly(L‐glutamic acid) and poly(N‐isopropylacrylamide)

A series of novel temperature‐ and pH‐responsive graft copolymers, poly(L ‐glutamic acid)‐g‐poly(N‐isopropylacrylamide), were synthesized by coupling amino‐semitelechelic poly(N‐isopropylacrylamide) with N‐hydroxysuccinimide‐activated poly(L ‐glutamic acid). The graft copolymers and their precursors were characterized, by ESI‐FTICR Mass Spectrum, intrinsic viscosity measurements and proton nuclear magnetic resonance (¹H NMR). The phase‐transition and aggregation behaviors of the graft copolymers in aqueous solutions were investigated by the turbidity measurements and dynamic laser scattering. The solution behavior of the copolymers showed dependence on both temperature and pH. The cloud point (CP) of the copolymer solution at pH 5.0–7.4 was slightly higher than that of the solution of the PNIPAM homopolymer because of the hydrophilic nature of the poly(glutamic acid) (PGA) backbone. The CP markedly decreased when the pH was lowered from 5 to 4.2, caused by the decrease in hydrophilicity of the PGA backbone. At a temperature above the lower critical solution temperature of the PNIPAM chain, the copolymers formed amphiphilic core‐shell aggregates at pH 4.5–7.4 and the particle size was reduced with decreasing pH. In contrast, larger hydrophobic aggregates were formed at pH 4.2. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4140–4150, 2008