Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

An efficient solid‐state polycondensation method for synthesizing stereocomplexed poly(lactic acid)s with high molecular weight

Simultaneous solid‐state polycondensation (SSP) of the powdery prepolymers of poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) can produce entire stereocomplexed poly(lactic acid)s (sc‐PLA) with high molecular weight and can be an alternative synthetic route to sc‐PLA. Ordinary melt polycondensations of L ‐ and D ‐lactic acids gave the PLLA and PDLA prepolymers having medium molecular weight which were pulverized for blending in 1:1 ratio. The resultant powder blends were then subjected to SSP at 130–160 °C for 30 h under a reduced pressure of 0.5 Torr. Some of the products thus obtained attained a molecular weight (M_w) as high as 200 kDa, consisting of stereoblock copolymer of PLLA and PDLA. A small amount of the stereocomplex should be formed in the boundaries of the partially melted PLLA and PDLA where the hetero‐chain connection is induced to generate the blocky components. The resultant SSP products showed predominant stereocomplexation after their melt‐processing in the presence of the stereoblock components in spite of containing a small amount of racemic sequences in the homo‐chiral PLLA and PDLA chains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3714–3722, 2008     

Immiscibility–miscibility phase transformation in blends of poly(ethylene succinate) with poly(L‐lactic acid)s of different molecular weights

Using differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and Fourier transformed infrared spectroscopy (FTIR), upper critical solution temperature (UCST) phase behavior with immiscibility–miscibility transformation in blends of poly(ethylene succinate) (PESu) with poly(lactic acid)s (PLAs), such as poly(D ,L ‐lactic acid) (PDLLA), poly(L ‐lactic acid) (PLLA), poly(D ‐lactic acid) (PDLA), differing in D/L configurations and molecular weights were investigated. All three binary blends of PDLLA/PESu, PLLA/PESu, and PESu/PDLA exhibit UCST behavior, which means they are immiscible at ambient temperature but can become miscible upon heating to higher temperatures at 240–268 °C depending on molecular weights. The PLLAs/PESu blends at UCST could be reverted back to the original phase‐separated morphology, as proven by solvent redissolution. The blends upon quenching from above UCST could be frozen into a quasi‐miscible state, where the Flory‐Huggins interaction parameter (χ₁₂) was determined to be a negative value (by melting point depression technique). The interaction between PDLLA and PESu in blend resulted in significant reduction in spherulite growth rate of PESu. Furthermore, blends of PESu with lower molecular weight PLLA or PDLA (M_w of PLLA and PDLA are 152,000 and 124,000 g/mol, respectively), instead of the higher M_w of PDLLA (M_w of PDLLA = 157,000 g/mol), are immiscible with UCST phase behavior, which are affected by molecular weights rather than the ratio of L/D monomer in the chemical structure of PLAs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1135–1147, 2010     

Synthesis of high‐molecular‐weight aliphatic–aromatic copolyesters from poly(ethylene‐co‐1,6‐hexene terephthalate) and poly(L‐lactic acid) by chain extension

A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, ¹H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than M_w = 3 × 10⁵ g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009     

Structure of poly(L‐lactic acid)s prepared by the dehydropolycondensation of L‐lactic acid with organotin catalysts

The synthesis of low‐molecular‐weight (weight‐average molecular weight < 45,000 g/mol) lactic acid polymers through the dehydropolycondensation of L ‐lactic acid was investigated. Polymerizations were carried out in solution with solvents (xylene, mesitylene, and decalin), without a solvent using different Lewis acid catalysts (tetraphenyl tin and tetra‐n‐butyldichlorodistannoxane), and at three different polymerization temperatures (143, 165, and 190 °C). The products were characterized with differential scanning calorimetry, size exclusion chromatography, vapor pressure osmometry, ¹³C NMR, and matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF). The resulting polymers contained less than 1 mol % lactide, as shown by NMR. The number‐average molecular weights were calculated from the ratio of the area peaks of ester carbonyl and carboxylic acid end groups via ¹³C NMR. The stereosequences were analyzed by ¹³C NMR spectroscopy on the basis of triad effects. Tetraphenyl tin was an effective transesterification catalyst, and the randomization of the stereosequence at 190 °C was observed. In contrast, the distannoxane catalyst caused comparatively less transesterification reaction, and the randomization of the stereosequences was slow even at 190 °C. The L ‐lactic acid and D ‐lactic acid isomers were added to the polymer chain in a small, blocky fashion. The MALDI‐TOF spectra of poly(L ‐lactic acid) (PLA) chains doped with Na⁺ and K⁺ cations showed that the PLA chains had the expected end groups. The MALDI‐TOF analysis also enabled the simultaneous detection of the cyclic oligomers of PLA present in these samples, and this led to the full structural characterization of the molecular species in PLA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2164–2177, 2005     

Mechanical properties and structure of the zone‐drawn poly(L‐lactic acid) fibers

The zone‐drawing (ZD) method was applied three times to the melt‐spun poly(L ‐lactic acid) (PLLA) fibers of low molecular weight (M_v = 13,100) at different temperatures under various tensions. The mechanical properties and superstructure of the ZD fibers were investigated. The resulting ZD‐3 fiber had a draw ratio of 10.5, birefringence of 37.31 × 10⁻³, and crystallinity of 37%, while an orientation factor of crystallites remarkably increased to 0.985 by the ZD‐1. The Young's modulus and tensile strength of the ZD‐3 fiber respectively attained 9.1 GPa and 275 MPa, and the dynamic storage modulus was 10.4 GPa at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 991–996, 1999     

Synthesis of poly(D,L‐lactic acid‐alt‐glycolic acid) from D,L‐3‐methylglycolide

D ,L ‐3‐Methylglycolide (MG) was synthesized via two step reactions with a good yield (42%). It was successfully polymerized in bulk with stannous octoate as a catalyst at 110 °C. The effects of the polymerization time and catalyst concentration on the molecular weight and monomer conversion were studied. Poly(D ,L ‐lactic acid‐co‐glycolic acid) (D ,L ‐PLGA50; 50/50 mol/mol) copolymers were successfully synthesized from the homopolymerization of MG with high polymerization rates and high monomer conversions under moderate polymerization conditions. ¹H NMR spectroscopy indicated that the bulk ring‐opening polymerization of MG conformed to the coordination–insertion mechanism. ¹³C NMR spectra of D ,L ‐PLGA50 copolymers obtained under different experimental conditions revealed that the copolymers had alternating structures of lactyl and glycolyl. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4179–4184, 2000     

Synthesis of poly(succinimide) by bulk polycondensation of L‐aspartic acid with an acid catalyst

The bulk polycondensation of L ‐aspartic acid (ASP) with an acid catalyst under batch and continuous conditions was established as a preparative method for producing poly(succinimide) (PSI). Although sulfuric acid, p‐toluenesulfonic acid, and methanesulfonic acid were effective at producing PSI in a high conversion of ASP, o‐phosphoric acid was the most suitable catalyst for yielding PSI with a high weight‐average molecular weight (M_w) in a quantitative conversion; that is, the M_w value was 24,000. For the continuous process using a twin‐screw extruder at 3.0 kg · h⁻¹ of the ASP feed rate, the conversion was greater than 99%, and the M_w value was 23,000 for the polycondensation with 10 wt % o‐phosphoric acid at 260°C. Sodium polyaspartate (PASP‐Na) originating from the acid‐catalyzed polycondensation exhibited high biodegradability and calcium‐ion‐chelating ability. The total organic carbon value was 86 ∼ 88%, and 100 g of PASP‐Na chelated with 5.5 ∼ 5.6 g of calcium ion, which was similar to the value for PASP‐Na from the acid‐catalyzed polycondensation with a mixed solvent © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 117–122, 2000     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Structural Characterization and Degradability of Poly(L‐lactic acid)s Incorporating Phenyl‐Substituted α‐Hydroxy Acids as Comonomers

Three types of copolymers of poly(L ‐lactic acid) (PLLA) were synthesized by direct polycondensation of L ‐lactic acid and phenyl‐substituted α‐hydroxy acids (L ‐phenyllactic acid and D ‐ and L ‐mandelic acids). It was found that the glass transition temperature of the copolymers comprising L ‐mandelic acid became significantly higher (from 58 to 69 °C) with increasing content of L ‐mandelic acid (from 0 to 50 mol‐%) although the M _w decreased (from 87 000 to 4 000 Da). The cast films of the L ‐mandelic acid containing copolymers showed improved tensile properties compared with those of the PLLA film. This may be due to a pinning effect of the L ‐mandelic acid units on the helix formation of PLLA, although 30% of the units were racemized. The enzymatic degradability of the L ‐mandelic acid containing copolymers was much higher than that of PLLA, as analyzed with Proteinase K® originating from Tritirachium album.

Synthesis of copolymers of L ‐lactic acid and phenyl‐substituted α‐hydroxy acids.     

Direct dehydration polycondensation of lactic acid catalyzed by water‐stable Lewis acids

Poly(L ‐lactic acid) (PLLA) is generally produced by ring‐opening polymerization of (S,S)‐lactide, which is prepared from dehydration polycondensation of lactic acid and successive depolymerization. Results of this study show that scandium trifluoromethanesulfonate [Sc(OTf)₃] and scandium trifluoromethanesulfonimide [Sc(NTf₂)₃] are effective for one‐step dehydration polycondensation of L ‐lactic acid. Bulk polycondensation of L ‐lactic acid was carried out at 130–170 °C to give PLLA with M_n of 5.1 × 10⁴ to 7.3 × 10⁴ (yield 32–60%). The solution polycondensation was performed at 135 °C for 48 h to afford PLLA with M_n of 1.1 × 10⁴ with good yield (90%). In no case did ¹H NMR, specific optical rotation, or DSC measurement confirm racemizations. The catalyst was recovered easily by extraction with water and reused for polycondensation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5247–5253, 2006     

Synthesis and properties of multiblock copolymers consisting of poly(L‐lactic acid) and poly(oxypropylene‐ co‐oxyethylene) prepared by direct polycondensation

A multiblock copoly(ester–ether) consisting of poly(l ‐lactic acid) (PLLA) and poly(oxypropylene‐co‐oxyethylene) (PN) was prepared and characterized. Preparation was done via the solution polycondensation of a thermal oligocondensate of l ‐lactic acid, a commercially available telechelic polyether (PN: Pluronic‐F68), and dodecanedioic acid as a carboxyl/hydroxyl adjusting agent. When stannous oxide was used as the catalyst, the molecular weight of the resultant PLLA/PN block copolymers became very high (even with a high PN content) under optimized reaction conditions. The refluxing of diphenyl ether (solvent) at reduced pressure allowed the efficient removal of the condensed water from the reaction system and the feed‐back of the intermediately formed l ‐lactide at the same time in order to successfully bring about a high degree of condensation. The copolymer films obtained by solution casting became more flexible with the increasing PN content as soft segments. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1513–1521, 1999     

Crystal modifications and multiple melting behavior of poly(L‐lactic acid‐co‐D‐lactic acid)

The crystal modifications and multiple melting behavior of poly(L ‐lactic acid‐co‐D ‐lactic acid) (98/2) as a function of crystallization temperature were studied by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). It was found that the disorder (α′) and order (α) phases of poly(L ‐lactic acid) (PLLA) were formed in cold‐crystallized poly(L ‐lactic acid‐co‐D ‐lactic acid) samples at low (<110 °C) and high (≥110 °C) temperatures, respectively. A disorder‐to‐order (α′‐to‐α) phase transition occurred during the annealing process of the α′‐crystal at elevated temperatures, which proceeded quite slowly even at the peak temperature of the exotherm P_exo but much more rapidly at higher temperature close to the melting region. The presence or absence of an additional endothermic peak before the exotherm in the DSC thermograph of the α′‐crystal was strongly dependent on the heating rate, indicating that a melting process involved during the α′‐to‐α phase transition. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Vibrational dynamics and heat capacity in poly(L‐lactic acid)

Poly(L ‐lactic acid) (PLLA) (? CH(CH₃) ? COO? )_n is a biodegradable polymer, which exhibits many applications in the biomedical field and where thermoplastics are employed. A comprehensive study of the normal modes and their dispersion in PLLA using Wilson′s GF matrix method as modified by Higgs is being reported. Assignments of calculated normal modes have been made and characteristic features of dispersion curves are discussed. Heat capacity has been calculated via density‐of‐states using Debye relation in the temperature range 10–250 K, which is in fairly good agreement with the experimental data. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 175–182, 2010     

Surface‐modified hydroxyapatite linked by L‐lactic acid oligomer in the absence of catalyst

A new surface modification method of hydroxyapatite nanoparticles (n‐HA) by surface grafting reaction of L ‐lactic acid oligomer with carboxyl terminal (LAc oligomer) in the absence of any catalyst was developed. The LAc oligomer with a certain molecular weight was directly synthesized by condensation of L ‐lactic acid. Surface‐modified HA nanoparticles (p‐HA) were attested by Fourier transformation infrared spectroscopy, ³¹P MAS‐NMR, and thermal gravimetric analysis (TGA). The results showed that LAc oligomer could be grafted onto the n‐HA surface by forming a Ca carboxylate bond. The grafting amount of LAc oligomer was about 13.3 wt %. The p‐HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p‐HA/PLLA composite containing 15 wt % of p‐HA were 68.7 MPa and 2.1 GPa, respectively, while those of the n‐HA/PLLA composites were 43 MPa and 1.6 GPa, respectively. The p‐HA/PLLA composites had better thermal stability than n‐HA/PLLA composites and neat PLLA had, as determined by isothermal TGA. The hydrolytic degradation behavior of the composites in phosphate buffered saline (PBS, pH 7.4) was investigated. The p‐HA/PLLA composites lost their mechanical properties more slowly than did n‐HA/PLLA composites in PBS because of their reinforced adhesion between the HA filler and PLLA matrix. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5177–5185, 2005     

Synthesis and characterization of multiblock copolymers based on L‐lactic acid,citric acid,and poly(ethylene glycol)

Because poly(L ‐lactic acid) (PLLA) is a biodegradable polyester with low immunogenicity and good biocompatibility, it is used as a biomaterial. However, hydrophobic PLLA does not have any reactive groups. Thus, its application is limited. To increase the hydrophilicity of PLLA and accelerate its degradation rate, functionalized pendant groups and blocks were introduced through copolymerization with citric acid and poly(ethylene glycol) (PEG), respectively. This article describes the synthesis and characterization of poly(L ‐lactic‐co‐citric acid) (PLCA)‐PLLA and PLCA‐PEG multiblock copolymers. The results indicated that the hydrolysis rate was enhanced, and the hydrophilicity was improved because of the incorporation of carboxyl groups in PLCA‐PLLA. The joining of the PEG block led to improved hydrophilicity of PLCA, and the degradation rate of PLCA‐PEG accelerated as compared with that of PLCA‐PLLA. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2073–2081, 2003     

Crystallization kinetics study of poly(L‐lactic acid)/carbon nanotubes nanocomposites

Effects of carbon nanotubes (CNT) on the isothermal crystallization kinetics of poly(L ‐lactic acid) (PLLA) were quantitatively investigated using the Avrami equation and the secondary nucleation theory of Lauritzen and Hoffman. CNT via grafting modification with PLLA could well disperse in the PLLA matrix and give significantly enhanced crystallization rate and crystallinity of PLLA as analyzed by differential scanning calorimetry and polarized optical microscopy. Analysis of isothermal crystallization kinetics using the Avrami equation demonstrated that CNT significantly enhanced the bulk crystallization of PLLA. Analysis of spherulite growth kinetics using the secondary nucleation theory of Lauritzen and Hoffman found that CNT could expand the temperature range of the crystallization regime III of PLLA. Values of the nucleation constant (K_g) in crystallization regimes III and II of PLLA both increased with increasing CNT contents. The K_g III/K_g II ratios were found to be close to the theoretical value 2 but were not clearly found to depend on the CNT contents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 983–989, 2010     

Synthesis of poly(acrylic acid)‐block‐poly(L‐valine) hybrid through combined atom transfer radical polymerization,click chemistry,and nickel‐catalyzed ring opening polymerization methods

A new hybrid amphiphilic system between a polyacrylic acid (PAA) synthetic segment, and a hydrophobic β‐sheet forming peptide segment, poly(L ‐valine) (PLVAL) was synthesized using a combination of Atom Transfer Radical Polymerization, Click Chemistry, and Nickel catalyzed ring opening of L ‐valine N‐carboxyanhydride. This is the first reported use of Click Chemistry as an intermediary step for the ω‐amino functionalization of polymers to obtain macroinitiators that are free from deactivating or interfering molecules to be used in subsequent Ni‐catalyzed ring opening reaction. The efficiency of the end‐group functionalization in the macroinitiator is about 90%. Three different PAA‐b‐PLVAL hybrid copolymers with molecular weight range of 8000–15,000 and M_w/M_n <1.3 had been prepared by varying the monomer to macroinitiator ratio. In addition, the highest achievable molecular weight in the copolymerization was found to be limited by the solubility of the growing chains. This combined synthetic approach can potentially be extended for the synthesis of a multitude of other peptide hybrid systems, and hence will be of interest in the preparation of peptide hybrid systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2646–2656, 2007     

Titanium‐mediated [CpTiCl2(OEt)] ring‐opening polymerization of lactides: A novel route to well‐defined polylactide‐based complex macromolecular architectures

Among three cyclopentadienyl titanium complexes studied, CpTiCl₂(OEt), containing a 5% excess CpTiCl₃, has proven to be a very efficient catalyst for the ring‐opening polymerization (ROP) of L ‐lactide (LLA) in toluene at 130 °C. Kinetic studies revealed that the polymerization yield (up to 100%) and the molecular weight increase linearly with time, leading to well‐defined PLLA with narrow molecular weight distributions (M_w/M_n ≤ 1.1). Based on the above results, PS‐b‐PLLA, PI‐b‐PLLA, PEO‐b‐PLLA block copolymers, and a PS‐b‐PI‐b‐PLLA triblock terpolymer were synthesized. The synthetic strategy involved: (a) the preparation of OH‐end‐functionalized homopolymers or diblock copolymers by anionic polymerization, (b) the reaction of the OH‐functionalized polymers with CpTiCl₃ to give the corresponding Ti‐macrocatalyst, and (c) the ROP of LLA to afford the final block copolymers. PMMA‐g‐PLLA [PMMA: poly(methyl methacrylate)] was also synthesized by: (a) the reaction of CpTiCl₃ with 2‐hydroxy ethyl methacrylate, HEMA, to give the Ti‐HEMA‐catalyst, (b) the ROP of LLA to afford a PLLA methacrylic‐macromonomer, and (c) the copolymerization (conventional and ATRP) of the macromonomer with MMA to afford the final graft copolymer. Intermediate and final products were characterized by NMR spectroscopy and size exclusion chromatography, equipped with refractive index and two‐angle laser light scattering detectors. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1092–1103, 2010     

Synthesis of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline)‐block‐poly(ε‐caprolactone) copolymers

A series of novel types of three‐armed poly(trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline)‐block‐poly(ε‐caprolactone) (PHpr‐b‐PCL) copolymers were successfully synthesized via melt block copolymerization of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) and ε‐caprolactone (ε‐CL) with a trifunctional initiator trimethylolpropane (TMP) and stannous octoate (SnOct₂) as a catalyst. For the homopolycondensation of N‐CBz‐Hpr with TMP initiator and SnOct₂ catalyst, the number‐average molecular weight (M_n) of prepolymer increases from 530 to 3540 g mol^?1 with the molar ratio of monomer to initiator (3–30), and the molecular weight distribution (M_w/M_n) is between 1.25 to 1.32. These three‐armed prepolymer PHpr were subsequently block copolymerized with ε‐caprolactone (ε‐CL) in the presence of SnOct₂ as a catalyst. The M_n of the copolymer increased from 2240 to 18,840 g mol^?1 with the molar ratio (0–60) of ε‐CL to PHpr. These products were characterized by differential scanning calorimetry (DSC), ¹H NMR, and gel permeation chromatography. According to DSC, the glass‐transition temperature (T_g) of the three‐armed polymers depended on the molar ratio of monomer/initiator that were added. In vitro degradation of these copolymers was evaluated from weight‐loss measurements and the change of M_n and M_w/M_n. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1708–1717, 2005