Radical copolymerization of alkyl 2‐norbornene‐2‐carboxylate with alkyl acrylates: Facile incorporation of norbornane framework into poly(alkyl acrylate)s

Radical copolymerization of alkyl 2‐norbornene‐2‐carboxylates (alkyl = Me 1a , nBu 1b ) with alkyl acrylates (alkyl = ethyl, methyl, and n‐butyl) was investigated. Copolymerization of 1a,b with the alkyl acrylates initiated by 1,1′‐azobis (cyclohexane‐1‐carbonitrile) at 85 °C proceeded to give random copolymers, although the homopolymerization of 1a,b did not proceed efficiently under the same conditions. Typically, bulk copolymerization of 1a with ethyl acrylate in a feed ratio of 1:3 ([ 1a ]:[EA]) afforded a copolymer with M_n = 33,300 containing 19.4 mol % of 1a unit in the composition. An increase of T_g derived from the incorporation of the rigid norbornane framework was observed, although the extent of the temperature rise was rather moderate. The ternary radical copolymerization of 1a,b /alkyl acrylate/N‐phenylmaleimide proceeded to give copolymers with the three repeating units in the main chain. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4597–4605, 2007     

Living cationic polymerization of vinyl ethers with a urethane group

To study the possibility of living cationic polymerization of vinyl ethers with a urethane group, 4‐vinyloxybutyl n‐butylcarbamate ( 1 ) and 4‐vinyloxybutyl phenylcarbamate ( 2 ) were polymerized with the hydrogen chloride/zinc chloride initiating system in methylene chloride solvent at ?30 °C ([monomer]₀ = 0.30 M, [HCl]₀/[ZnCl₂]₀ = 5.0/2.0 mM). The polymerization of 1 was very slow and gave only low‐molecular‐weight polymers with a number‐average molecular weight (M_n) of about 2000 even at 100% monomer conversion. The structural analysis of the products showed occurrence of chain‐transfer reactions because of the urethane group of monomer 1 . In contrast, the polymerization of vinyl ether 2 proceeded much faster than 1 and led to high‐molecular‐weight polymers with narrow molecular weight distributions (MWDs ≤ ～1.2) in quantitative yield. The M_n's of the product polymers increased in direct proportion to monomer conversion and continued to increase linearly after sequential addition of a fresh monomer feed to the almost completely polymerized reaction mixture, whereas the MWDs of the polymers remained narrow. These results indicated the formation of living polymer from vinyl ether 2 . The difference of living nature between monomers 1 and 2 was attributable to the difference of the electron‐withdrawing power of the carbamate substituents, namely, n‐butyl for 1 versus phenyl for 2 , of the monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2960–2972, 2004     

Living carbocationic copolymerization of isobutylene with styrene

The carbocationic copolymerization of isobutylene (IB) and styrene (St), initiated by 2‐chloro‐2,4,4‐trimethylpentane/TiCl₄ in 60/40 (v/v) methyl chloride/hexane at ?90 °C, was investigated. At a low total concentration (0.5 mol/L), slow initiation and rapid monomer conversion were observed. At a high total comonomer concentration (3 mol/L), living conditions (a linear semilogarithmic rate and M_n–conversion plots) were found, provided that the St concentration was above a critical value ([St]₀ ～ 0.6 mol/L). The breadth of the molecular weight distribution decreased with increasing IB concentration in the feed, reaching M_w/M_n ～ 1.1. St homopolymerization was also living at a high total concentration, yielding polystyrene with M_n = 82,000 g/mol, the highest molecular weight ever achieved in carbocationic St polymerization. An analysis of this system by both the traditional gravimetric–NMR copolymer composition method and FTIR demonstrated penultimate effects. IB enrichment was found in the copolymers at all feed compositions, with very little drift at a high total concentration and above the critical St concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1778–1787, 2007     

Block copolymerization of allene derivatives with 1,3-butadiene by living coordination polymerization with π-allylnickel catalyst

The block copolymerization of allene derivatives (3A–3D) with 1,3-butadiene (2) by [(allyl)NiOCOCF₃]₂ (1) is described. For instance, the living coordination polymerization of phenylallene (3A, 50 equiv) starting from the living poly(2), which was prepared by the polymerization of 2 (160 equiv) by 1, successfully gave a block copolymer of 2 and 3A in high yield. The molecular weight of the block copolymer (4A) in gel permeation chromatography shifted clearly to the higher molecular weight region and kept a unimodal distribution (M_n = 17,400, M_w/M_n = 1.23) in comparison with that of the starting living poly(2) (M_n = 5,600, M_w/M_n = 1.67). The ratio of each segment and the molecular weight of the resulting copolymers could be controlled by the feed ratio of each monomer. The block copolymerization also proceeded successfully by the inverse order of the monomer feeding (i.e., the polymerization of 3A followed by that of 2) to obtain the corresponding block copolymers in high yields. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3916–3921, 1999     

Radical ring‐opening copolymerization behavior of vinyloxirane: Synthesis of copolymer from 2‐isopropenyl‐3‐phenyloxirane and styrene and its functionalization

The radical ring‐opening copolymerization of 2‐isopropenyl‐3‐phenyloxirane (1) with styrene (St) was examined to obtain the copolymer [copoly(1‐St)] with a vinyl ether moiety in the main chain. The copolymers were obtained in moderate yields by copolymerization in various feed ratios of 1 and St over 120 °C; the number‐average molecular weights (M_n) were estimated to be 1800–4200 by gel permeation chromatography analysis. The ratio of the vinyl ether and St units of copoly(1‐St) was estimated with the ¹H NMR spectra and varied from 1/7 to 1/14 according to the initial feed ratio of 1 and St. The haloalkoxylation of copoly(1‐St) with ethylene glycol in the presence of N‐chlorosuccinimide produced a new copolymer with alcohol groups and chlorine atoms in the side group in a high yield. The M_n value of the haloalkoxylated polymer was almost the same as that of the starting copoly(1‐St). The incorporated halogen was determined by elemental analysis. The analytical result indicated that over 88% of the vinyl ether groups participated in the haloalkoxylation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3729–3735, 2000     

Synthesis of poly(tert‐butyl methacrylate)‐graft‐poly(dimethylsiloxane) graft copolymers via reversible addition‐fragmentation chain transfer polymerization

Well‐defined poly(tert‐butyl methacrylate)‐graft‐poly (dimethylsiloxane) (PtBuMA‐g‐PDMS) graft copolymers were synthesized via reversible addition‐fragmentation chain transfer (RAFT) copolymerization of methacryloyl‐terminated poly (dimethylsiloxane) (PDMS‐MA) with tert‐butyl methacrylate (tBuMA) in ethyl acetate, using 2,2′‐azobis(isobutyronitrile) (AIBN) as the initiator and 2‐cyanoprop‐2‐yl dithiobenzoate as the RAFT agent. The RAFT statistical copolymerization of PDMS‐MA with tBuMA is shown to be azeotropic and the obtained PtBuMA‐g‐PDMS graft copolymers have homogeneously distributed branches because of the similar reactivity of monomers (r_tBuMA ≈ r_PDMS‐MA ≈ 1). By the RAFT block copolymerization of PDMS‐MA with tBuMA, moreover, narrow molecular weight distribution (M_w/M_n < 1.3) PtBuMA‐g‐PDMS graft copolymers with gradient or blocky branch spacing were synthesized. The graft copolymers exhibit the glass transitions corresponding to the PDMS and PtBuMA phase, respectively. However, the arrangement of monomer units in copolymer chains and the length of PtBuMA moieties have important effects on the thermal behavior of PtBuMA‐g‐PDMS graft copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Atom transfer radical polymerization of acrylates in an ionic liquid: Synthesis of block copolymers

Atom transfer radical polymerization (ATRP) of acrylates in ionic liquid, 1‐butyl‐3‐methylimidazolium hexaflurophospate, with the CuBr/CuBr₂/amine catalytic system was investigated. Sequential polymerization was performed by synthesizing AB block copolymers. Polymerization of butyl acrylate (monomer that is only partly soluble in an ionic liquid forming a two‐phase system) proceeded to practically quantitative conversion. If the second monomer (methyl acrylate) is added at this stage, polymerization proceeds, and block copolymer formed is essentially free of homopolymer according to size exclusion chromatographic analysis. The number‐average molecular weight of the copolymer is slightly higher than calculated, but the molecular weight distribution is low (M_w/M_n = 1.12). If, however, methyl acrylate (monomer that is soluble in an ionic liquid) is polymerized at the first stage, then butyl acrylate in the second‐stage situation is different. Block copolymer free of homopolymer of the first block (with M_w/M_n = 1.13) may be obtained only if the conversion of methyl acrylate at the stage when second monomer is added is not higher than 70%. Matrix‐assisted laser desorption/ionization time‐of‐flight analysis confirmed that irreversible deactivation of growing macromolecules is significant for methyl acrylate polymerization at a monomer conversion above 70%, whereas it is still not significant for butyl acrylate even at practically quantitative conversion. These results show that ATRP of butyl acrylate in ionic liquid followed by addition of a second acrylate monomer allows the clean synthesis of block copolymers by one‐pot sequential polymerization even if the first stage is carried out to complete conversion of butyl acrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2799–2809, 2002     

Anionic copolymerization of 1,1-diphenylethylene and 2,3-dimethylbutadiene

1,1-Diphenylethylene (M₂) and 2,3-dimethylbutadiene (M₁) were copolymerized with n-butyllithium in tetrahydrofuran. The rate of consumption of each monomer was followed by the change of high resolution NMR spectra of the reaction mixture. The copolymerization proceeded alternately, if the ratio of initial monomer concentrations, [M₂]₀/[M₁]₀, was sufficiently larger than unity. By assuming the rate constant k₂₂ to be zero, the constants k₂₁ were obtained from the consumption rates of the monomers. In the alternating copolymerization, 2,3-dimethylbutadiene was incorporated into the copolymer only as the 1,4-structure, while the 1,2-structure was predominant in homopolymerization.     

Cationic ring‐opening polymerization of ϵ‐thionocaprolactone: Selective formation of polythioester

Cationic ring‐opening polymerization of ϵ‐thionocaprolactone was examined. The corresponding polythioester with the number‐average molecular weight (M_n ) of 57,000 was obtained in the polymerization with 1 mol % of BF₃ · OEt₂ as an initiator in CH₂Cl₂ at 28 °C for 5 h with quantitative monomer conversion. The M_n of the polymer increased with the solvent polarity and monomer‐to‐initiator ratio. No polymerization took place below −30 °C, and the monomer conversion and M_n of the polymer increased with the temperature in the range of −15 to 28 °C. The increase of initial monomer concentration was effective to improve the monomer conversion and the M_n of the obtained polymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4057–4061, 2000     

Radical copolymerization behavior of a highly fluorinated cyclic olefin with vinyl ether

The copolymerization of a highly fluorinated cyclic monomer, octafluorocyclopentene (OFCPE, M₁), with ethyl vinyl ether (EVE, M₂) was investigated with a radical initiator in bulk. Despite the poor homopolymerizability of each monomer, the copolymerization proceeded successfully, and the molecular weights of the copolymers reached up to more than 10,000. Incorporation of the OFCPE units into the copolymer led to an increase in the glass‐transition point. The copolymer composition was determined from ¹H NMR spectra and elemental analysis data. The molar fraction of the OFCPE unit in the copolymer increased and approached but did not exceed 0.5. The monomer reactivity ratios were estimated by the Yamada–Itahashi–Otsu nonlinear least‐squares procedure as r_1,OFCPE = ?0.008 ± 0.010 and r_2,EVE = 0.192 ± 0.015. The reactivity ratios clearly suggest that the copolymerization proceeds alternatively in the case of an excessive feed of OFCPE. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1151–1156, 2002     

Synthesis of macrocycles by the ring‐crossover reaction of a cyclic dithioester

The ring‐crossover polymerization of cyclic dithioester 1 was performed in the presence of quaternary onium salts as catalysts at 70–150 °C for 24 h in NMP. It was found that predictable cyclic polymers with the same repeating structures as 1 were obtained with M_ns in the range between 700 and 3,500, quantitatively. It was observed that intermolecular and intramolecular thioester‐exchange reactions proceeded between cyclic monomer 1 and resulting cyclic polymers under thermodynamic control to give a lower‐molecular‐weight cyclic polymer with a lower polydispersity ratio (M_n = 2,400, M_w/M_n = 1.70). © 2006Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 680–687, 2007     

Copolymerization of 1,3‐butadiene and isoprene with cobalt dichloride/methylaluminoxane in the presence of triphenylphosphine

The homopolymerization and copolymerization of 1,3‐butadiene and isoprene were achieved at 0 °C with cobalt dichloride in combination with methylaluminoxane and triphenylphosphine (Ph₃P). For 1,3‐butadiene, highly cis‐specific and 1,2‐syndiospecific polymerization proceeded in the absence or presence of Ph₃P, respectively, although the activity with Ph₃P was much higher than that without Ph₃P. Only a trace of the polymer was, however, obtained in isoprene polymerization when Ph₃P had been added. For copolymerization, the polymer yield in the presence of Ph₃P was about three times higher than that in its absence. Copolymerization in the presence of Ph₃P was, therefore, investigated in more detail. Unimodal gel permeation chromatography elution curves with narrower polydispersity (weight‐average molecular weight/number‐average molecular weight ≈ 1.5) indicated that the propagation reaction proceeded by single‐site active species. Both the yield and molecular weight of the copolymer decreased with an increasing amount of isoprene in the feed, and this was followed by an increase in the isoprene content in the copolymer. The monomer reactivity ratios, r₁ (1,3‐butadiene) and r₂ (isoprene), were estimated to be 2.8 and 0.15, respectively. Although the 1,3‐butadiene content in the copolymer was strongly dependent on the comonomer composition in the feed, the ratio of 1,2‐inserted units to 1,4‐inserted units of 1,3‐butadiene was constant. Concerning the isoprene unit, the percentage of 1,2‐ and 3,4‐inserted units was increased at the expense of 1,4‐inserted units with an increasing isoprene content in the feed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3086–3092, 2002     

Atom transfer radical copolymerization of styrene and N‐cyclohexylmaleimide

Atom transfer radical copolymerization of Styrene (St) and N‐cyclohexylmaleimide (NCMI) with the CuBr/bipyridine catalyst in anisole, initiated by 1‐phenylethyl bromide (1‐PEBr) or tetra‐(bromomethyl)benzene (TBMB), afforded well‐defined copolymers with predetermined molecular weights and low polydispersities, M_w/M_n < 1.5. The influences of several factors, such as temperature, solvent, and monomer ratio, on the copolymerization with the CuBr/bpy catalyst system were subsequently investigated. The apparent enthalpy of activation for the overall copolymerization was measured to be 28.2 kJ/mol. The monomer reactivity ratios were evaluated to be r_NCMI = 0.046 and r_St = 0.127. Using TBMB as the initiator produced four‐armed star copolymer. The copolymerization of styrene and NCMI with TBMB/CuBr/bpy in PhOCH₃ at 110 °C was found to provide good control of molecular weights and polydispersities and the similar copolymerization in cyclohexanone displayed poor control. The glass transition temperature of the resultant copolymer increases with increasing f_NCMI, which indicates that the heat resistance of the copolymer has been improved by increasing NCMI. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1203–1209, 2000     

Synthesis of a novel hybrid liquid‐crystalline rod–coil diblock copolymer

A series of novel rod–coil diblock copolymers on the basis of mesogen‐jacketed liquid‐crystalline polymer were successfully prepared by atom transfer radical polymerization from the flexible polydimethylsiloxane (PDMS) macroinitiator. The hybrid diblock copolymers, poly{2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene}‐block‐polydimethylsiloxane, had number‐average molecular weights (M_n's) ranging from 9500 to 30,900 and relatively narrow polydispersities (≤1.34). The polymerization proceeded with first‐order kinetics. Data from differential scanning calorimetry validated the microphase separation of the diblock copolymers. All block copolymers exhibited thermotropic liquid‐crystalline behavior except for the one with M_n being 9500. Four liquid‐crystalline diblock copolymers with PDMS weight fractions of more than 18% had two distinctive glass‐transition temperatures. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1799–1806, 2003     

Chain‐growth condensation polymerization approach to synthesis of well‐defined polybenzoxazole: Importance of higher reactivity of 3‐amino‐4‐hydroxybenzoic acid ester compared to 4‐amino‐3‐hydroxybenzoic acid ester

Application of chain‐growth condensation polymerization (CGCP) to obtain well‐defined polybenzoxazole (PBO) was examined. CGCP of both phenyl 3‐{(2‐methoxyethoxy)methoxy (MEM‐oxy)}‐4‐(octylamino)benzoate ( 1b ) (para‐substituted monomer) and phenyl 4‐MEM‐oxy‐3‐(octylamino)benzoate ( 3b ) (meta‐substituted monomer) was examined in the presence of metal disilazide base and phenyl 4‐nitro‐ or methylbenzoate 2 as an initiator. Polymerization of the latter monomer, but not the former, afforded polymer with controlled molecular weight based on the feed ratio of monomer to initiator and with a narrow molecular weight distribution. Accordingly, monomer 3c , in which the octyl group on the amino nitrogen of 3b was replaced with a 4‐(octyloxy)benzyl (OOB) group, was polymerized in the presence of lithium 1,1,1,3,3,3‐hexamethyldisilazide (LiHMDS), phenyl 4‐methylbenzoate ( 2b ), and LiCl in THF at 0 °C to yield poly 3c with well‐defined molecular weight (M_n = 4520–9080) and low polydispersity (M_w/M_n ≤ 1.11). Treatment of poly 3c with trifluoroacetic acid simultaneously removed the MEM and OOB groups, affording poly(o‐hydroxyamide) (poly 4 ) without scission of the amide linkages. Cyclodehydration of poly 4 proceeded at 350 °C to yield PBO (poly 5 ), which was insoluble in organic solvents and acids. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1730–1736     

Living/controlled cationic cyclopolymerization of divinyl ether with a cyclic acetal moiety: Synthesis of poly(vinyl ether)s with high glass transition temperature based on incorporation of cyclized main chain and cyclic side chains

Cationic cyclopolymerization of 2‐methyl‐5,5‐bis(vinyloxymethyl)‐1,3‐dioxane ( 1 ), a divinyl ether with a cyclic acetal group, was investigated with the HCl/ZnCl₂ initiating system in toluene and methylene chloride at ?30 °C. The reaction proceeded quantitatively to give gel‐free, soluble polymers in organic solvents. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion, and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that the polymerization proceeded in living/controlled manner. The contents of the unreacted vinyl groups in the produced soluble polymers were less than ～3 mol %, and therefore, the degree of cyclization was determined to be ～97%. In contrast, the pendant cyclic acetal groups remained intact in the polymers under the present cationic polymerization conditions. These facts show that cyclopolymerization of 1 almost exclusively occurred and the poly(vinyl ether)s with the cyclized repeating units and cyclic pendant acetal rings were obtained. Glass transition temperature (T_g) and thermal decomposition temperature (T_d) of poly( 1 ) (M_n = 7870, M_w/M_n = 1.57) were found to be 166 and 338 °C, respectively, indicating that poly( 1 ) had high T_g and high thermal stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 952–958, 2010     

Living radical graft polymerization of methyl methacrylate to polyethylene film with typical and reverse atom transfer radical polymerization

Nickel‐mediated atom transfer radical polymerization (ATRP) and iron‐mediated reverse ATRP were applied to the living radical graft polymerization of methyl methacrylate onto solid high‐density polyethylene (HDPE) films modified with 2,2,2‐tribromoethanol and benzophenone, respectively. The number‐average molecular weight (M_n) of the free poly(methyl methacrylate) (PMMA) produced simultaneously during grafting grew with the monomer conversion. The weight‐average molecular weight/number‐average molecular weight ratio (M_w/M_n) was small (<1.4), indicating a controlled polymerization. The grafting ratio showed a linear relation with M_n of the free PMMA for both reaction systems. With the same characteristics assumed for both free and graft PMMA, the grafting was controlled, and the increase in grafting ratio was ascribed to the growing chain length of the graft PMMA. In fact, M_n and M_w/M_n of the grafted PMMA chains cleaved from the polyethylene substrate were only slightly larger than those of the free PMMA chains, and this was confirmed in the system of nickel‐mediated ATRP. An appropriate period of UV preirradiation controlled the amount of initiation groups introduced to the HDPE film modified with benzophenone. The grafting ratio increased linearly with the preirradiation time. The graft polymerizations for both reaction systems proceeded in a controlled fashion. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3350–3359, 2002     

Preparation and characterization of graft terpolymers with controlled molecular structure

Segmented terpolymers, poly(alkyl methacrylate)‐g‐poly(D ‐lactide)/poly(dimethylsiloxane) (PLA/PDMS), were prepared with a combination of the “grafting through” technique (macromonomer method) and controlled/living radical polymerization (atom transfer radical polymerization or reversible addition–fragmentation transfer polymerization). Two synthetic pathways were used. The first was a single‐step approach in which a low‐molecular‐weight methacrylate monomer (methyl methacrylate or butyl methacrylate) was copolymerized with a PLA macromonomer and a PDMS macromonomer. The second strategy was a two‐step approach in which a graft copolymer containing one macromonomer was chain‐extended by a copolymerization of the second macromonomer and the low‐molecular‐weight methacrylate. The kinetics of both synthetic approaches were investigated, showing that the polymerizations exhibited a controlled/living behavior. Furthermore, the molecular structure of the terpolymers (composition, molecular weight distribution, and microstructure) was investigated by two‐dimensional liquid chromatography. Well‐defined terpolymers with controlled branch distribution, composition (F_w,PMMA/F_w,PLA/F_w,PDMS ～ 50/30/20) molecular weight (M_n ～ 50,000 g · mol^?1), and a narrow molecular weight distribution (M_w/M_n ～ 1.3) were prepared via both pathways. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1939–1952, 2004     

Cationic copolymerization of indene with styrene derivatives: Synthesis of random copolymers of indene with high molecular weight

Random copolymers with high molecular weights of indene and p‐methylstyrene (pMeSt) were synthesized by cationic polymerization with trichloroacetic acid/tin tetrachloride in CH₂Cl₂ at low temperatures. When indene and pMeSt (1:1 v/v), for example, were polymerized at ?40 °C, both monomers were consumed at very similar rates to give a copolymer with high molecular weight [number‐average molecular weight (M_n): 8–9 × 10⁴]. This is indeed quite unexpected behavior for the combination of these two monomers because pMeSt polymerized over 1000 times faster than indene in the homopolymerization under the reaction conditions previously described. The product copolymer of indene and pMeSt had a random monomer sequence in it that was confirmed by NMR analyses and thermal‐property measurements. In sharp contrast with pMeSt, styrene and p‐chlorostyrene, which have no electron‐donating groups on the phenyl ring, led to low molecular weight polymers (M_n < 10,000) in the copolymerization with indene (1:1 v/v). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2449–2457, 2002     

Cationic copolymerization of ε‐caprolactone and L,L‐lactide by an activated monomer mechanism

The cationic homopolymerization and copolymerization of L,L ‐lactide and ε‐caprolactone in the presence of alcohol have been studied. The rate of homopolymerization of ε‐caprolactone is slightly higher than that of L,L ‐lactide. In the copolymerization, the reverse order of reactivities has been observed, and L,L ‐lactide is preferentially incorporated into the copolymer. Both the homopolymerization and copolymerization proceed by an activated monomer mechanism, and the molecular weights and dispersities are controlled {number‐average degree of polymerization = ([M]₀ ? [M]_t)/[I]₀, where [M]₀ is the initial monomer concentration, [M]_t is the monomer concentration at time t, and [I]₀ is the initial initiator concentration; weight‐average molecular weight/number‐average molecular weight ～1.1–1.3}. An analysis of ¹³C NMR spectra of the copolymers indicates that transesterification is slow in comparison with propagation, and the microstructure of the copolymers is governed by the relative reactivity of the comonomers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 7071–7081, 2006