Influence of hydrophobic monomers on secondary nucleation of hydroxyl‐functionalized latexes

The influence of butyl acrylate (BA) and methyl methacrylate (MMA) on hydroxyl functionalized latexes was investigated. The hydrophobicity of the monomer feed was varied via the BA/MMA ratio. In addition to monitoring the effect of hydrophobic monomer feed on secondary nucleation, the polymerization kinetics and final latex properties were also obtained for comparison. Five different BA to MMA molar ratios were combined with five 2‐hydroxyethyl methacrylate (HEMA) concentrations (0, 10, 20, 30 and 40 mol% in monomer composition). All latexes were synthesized through seeded semibatch emulsion polymerization process. Particle size distributions and average particle sizes of the latexes were determined by dynamic light scattering (DLS) and qualitatively compared with transmission electron microscope (TEM) images. The BA to MMA ratio significantly influences the boundary HEMA concentration at which homogeneous secondary nucleation occurs. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2190–2202     

Particle formation under monomer‐starved conditions in the semibatch emulsion polymerization of styrene. I. Experimental

Particle formation and particle growth compete in the course of an emulsion polymerization reaction. Any variation in the rate of particle growth, therefore, will result in an opposite effect on the rate of particle formation. The particle formation in a semibatch emulsion polymerization of styrene under monomer‐starved conditions was studied. The semibatch emulsion polymerization reactions were started by the monomer being fed at a low rate to a reaction vessel containing deionized water, an emulsifier, and an initiator. The number of polymer particles increased with a decreasing monomer feed rate. A much larger number of particles (within 1–2 orders of magnitude) than that generally expected from a conventional batch emulsion polymerization was obtained. The results showed a higher dependence of the number of polymer particles on the emulsifier and initiator concentrations compared with that for a batch emulsion polymerization. The size distribution of the particles was characterized by a positive skewness due to the declining rate of the growth of particles during the nucleation stage. A routine for monomer partitioning among the polymer phase, the aqueous phase, and micelles was developed. The results showed that particle formation most likely occurred under monomer‐starved conditions. A small average radical number was obtained because of the formation of a large number of polymer particles, so the kinetics of the system could be explained by a zero–one system. The particle size distribution of the latexes broadened with time as a result of stochastic broadening associated with zero–one systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3940–3952, 2001     

Particle formation and coagulation in the seeded semibatch emulsion polymerization of butyl acrylate

Particle formation and coagulation in the seeded semibatch emulsion polymerization of butyl acrylate were studied under monomer‐starved conditions. To investigate the importance of the kinetics of the water phase in the nucleation process, the monomer feed rate was used as a variable to alter the monomer concentration in the aqueous phase. The emulsifier concentration in the feed was employed to alter the particle stability. Particle formation and coagulation were discussed in terms of critical surface coverage ratios. Particle coagulation occurred if the particle surface coverage dropped below θ_cr1 = 0.25 ± 0.05. The secondary nucleation occurred above a critical surface coverage of θ_cr2 = 0.55 ± 0.05. The number of particles remained approximately constant if the particle surface coverage was within θ_cr1 = 0.25 < θ < θ_cr2 = 0.55. This surface coverage band is equivalent to the surface tension band of 42.50 ± 5.0 dyne/cm that is required to avoid particle formation and coagulation in the course of polymerization. The kinetics of the water phase was shown to play an important role during homogeneous and micellar nucleations. For any fixed emulsifier concentration in the feed and above θ_cr2, the number of secondary particles increased with monomer concentration in the aqueous phase. Moreover, the presence of micelles in the reaction vessel is not the only perquisite for micellar nucleation to occur, a sufficient amount of monomer should be present in the aqueous phase to enhance the radical capture by partially monomer‐swollen micelles. The rate of polymerization increased with the surfactant concentration in the aqueous phase. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3612–3630, 2000     

High solids TEMPO‐mediated radical semibatch emulsion polymerization of styrene

A bicomponent initiation system consisting of 2,2,6,6‐tetramethylpiperidine‐N‐oxyl (TEMPO) and the water soluble initiator potassium persulfate (KPS) was used to develop a robust and versatile semibatch emulsion polymerization process to obtain polystyrene (PS) latexes with solids contents of 5–40 wt %. A window of operating conditions was found that yielded high conversion (>95%) stable latexes and well controlled polymers, overcoming limitations found in previous attempts at developing similar processes using TEMPO. The critical parameters studied were surfactant concentration, monomer concentration in the nucleation step and the monomer feed rate in the semibatch step. Methyl acrylate (MA) was used in the nucleation step to improve the nitroxide efficiency (N_Eff). Latexes having molecular weight distribution (MWD) with dispersity (?) lower than 1.5, average particle size (D_p) from ≈32 to ≈500 nm, nitroxide efficiencies N_Eff up to ≈1.0 and monomer conversions >90% were obtained in less than 12 h with solids contents up to 40 wt %. These results constitute a significant advance over prior efforts in TEMPO‐mediated polymerization in aqueous dispersions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 49–62     

Particle formation in interval III of the emulsion polymerization of styrene with aerosol‐MA as an emulsifier

Particle nucleation in the seeded emulsion polymerization of styrene in the presence of Aerosol‐MA emulsifier micelles and in the absence of monomer droplets (interval III) was investigated. The seed particles were swollen with different amounts of the styrene monomer before the experiments. A larger number of polymer particles formed in interval III than in the corresponding seeded batch operation in the presence of monomer droplets. The increase in the number of particles could be attributed to the reduced rate of growth of new particles, which retarded the depletion of emulsifier micelles. The number of secondary particles initially increased with the initial polymer weight ratio in the seed particles (w_p0) but decreased at a higher range of w_p0, after reaching a maximum at w_p0 = 0.60, and eventually was reduced to zero. At high values of w_p0 (>0.75), polymerization occurred in the seed particles, whereas few or no new particles were formed despite the presence of micelles. The cessation of particle formation at high conversions was ascertained with a semibatch process in which the neat monomer feed was added to the reaction vessel containing the seed particles and emulsifier micelles. For w_p0 > 0.85, the emulsifier micelles were disintegrated to stabilize the seed particles with no secondary particle formation. The possible reasons for the cessation of particle formation at high w_p0 were examined. The size distribution of secondary particles showed a positive skewness in terms of volume because of the declining rate of growth for particles, together with a low rate of growth for small particles. The distribution breadth of new particles sharpened with increasing w_p0. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1652–1663, 2002     

Sterically stabilized emulsion polymerization of styrene: Pseudo‐semicontinuous approach

The sterically stabilized emulsion polymerization of styrene initiated by a water‐soluble initiator at different temperatures has been investigated. The rate of polymerization (R_p) versus conversion curve shows the two non‐stationary‐rate intervals typical for the polymerization proceeding under non‐stationary‐state conditions. The shape of the R_p versus conversion curve results from two opposite effects—the increased number of particles and the decreased monomer concentration at reaction loci as the polymerization advances. At elevated temperatures the monomer emulsion equilibrates to a two‐phase or three‐phase system. The upper phase is transparent (monomer), and the lower one is blue colored, typical for microemulsion. After stirring such a multiphase system and initiation of polymerization, the initial coarse polymer emulsion was formed. The average size of monomer/polymer particles strongly decreased up to about 40% conversion and then leveled off. The initial large particles are assumed to be highly monomer‐swollen particles formed by the heteroagglomeration of unstable polymer particles and monomer droplets. The size of the “highly monomer” swollen particles continuously decreases with conversion, and they merge with the growing particles at about 40–50% conversion. The monomer droplets and/or large highly monomer‐swollen polymer particles also serve as a reservoir of monomer and emulsifier. The continuous release of nonionic (hydrophobic) emulsifier from the monomer phase increases the colloidal stability of primary particles and the number of polymer particles, that is, the particle nucleation is shifted to the higher conversion region. Variations of the square and cube of the mean droplet radius with aging time indicate that neither the coalescence nor the Ostwald ripening is the main driving force for the droplet instability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 804–820, 2003     

Analysis of particle formation under monomer-starved conditions in emulsion polymerization reactors

An important characteristic of monomer-starved nucleation in semibatch reactors is that the rate of growth of particles is controlled by the rate of monomer addition. The reduced rate of growth of particles prolongs the nucleation interval by slowing down the rate of emulsifier micelle depletion and forms a larger number of particles (N_p). Model calculations show how N_p varies with the formulation parameters as the monomer-flooded nucleation shifts into monomer-starved one. Particle formation in the intermediate conversion of interval III of the styrene batch emulsion polymerization also showed an enhancement because of a low rate of growth of newly formed particles. However, at a higher conversion, the rate of particle formation decreased significantly. Modeling results show that the reduction in the rate of particle formation at high conversions could not be simply explained by existing theories which rely on the decrease in monomer concentration in the aqueous phase as a means to explain the decrease in the rate of radical capture.     

The effect of cosurfactants and the initiator concentration on the polymer to surfactant concentration in nanolatexes

The effect of cosurfactant and initiator concentration on the ab initio production of nanolatexes using low surfactant levels was investigated. While the use of cosurfactants (acrylic acid and pentanol) increased the amount of monomer that can be used in styrene‐SDS microemulsion formulations to 13 wt %, high surfactant concentrations are still required, resulting in polymer‐to‐surfactant ratios (Pol/Surf) <1. Latexes with particle size of 30 ± 5 nm were produced upon polymerization of these microemulsions. The Pol/Surf can be significantly increased by increasing the initiator concentration of emulsion polymerization recipes. Particle sizes are comparable with microemulsion latexes, however, less surfactant is required. The reduction in the particle size with higher initiator concentration is attributed to a higher efficiency of particle nucleation and to a higher nucleation rate relative to the rate of monomer transfer. Nanolatexes (particle size < 30 nm) were obtained with 19 wt % solids content and Pol/Surf of 3.6 in ab initio. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Comparative study of monomer droplet nucleation in the seeded batch and semibatch miniemulsion polymerisation of styrene

Monomer droplet nucleation in the seeded miniemulsion polymerisation of styrene under monomer-flooded and monomer-starved conditions was studied. The miniemulsion feeds were added to the reactor either batchwise or semibatchwise. The droplets preserved longer under flooded conditions. As a result, the batch operation led to a larger number of particles (N_p) than the semibatch operation. For the miniemulsion droplets containing predissolved polymer, the final N_p was independent of the way that the feed was added to the reactor and was equivalent to the number of monomer droplets in the original miniemulsion feed. The size distribution of the final latexes, however, was influenced by the operation type. For the batch operation, the rate of polymerisation (R_p) with the miniemulsion feeds was higher than that with the conventional monomer emulsion feed because of the monomer droplet nucleation. But for the semibatch operation, the opposite was true because of R_p controlled by the rate of monomer diffusion from rather stable miniemulsion droplets to the growing polymer particles.     

SEED SEMICONTINUOUS EMULSION MULTI-COPOLYMERIZATION OF (METH) ACRYLATES WITH HIGH-SOLID CONTENT: EFFECT OF THE OPERATION CONDITIONS

The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA),2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate(HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solidcontent. The effects of monomer emulsion feed rates (R_a) and (R/E)_E values, the ratio ofemulsifier amount between the initial charge (R) and the addition monomer emulsion (E),on the polymerization reaction features, the viscosities, surface tensions,particle sizes andparticle sizes distributions of latexes,T_g and the insoluble fractions of films, the 180° peelstrength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, preparedfrom the latexes, were studied. Experimental study shows that the grafting and cross-linking fraction in the PSA tapes must be controlled within a suitable range to keep thebalance of the 180° peel strength, tack and holding power.     

Synthesis of saccharidic polymer colloids via free radical mini‐emulsion polymerization

Polymer colloids based on 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐α‐D ‐glucofuranose (3‐MDG) and butyl acrylate (BA) were prepared via free radical mini‐emulsion polymerization. The kinetic and colloidal features of the copolymerization were investigated. The final particle size (D) of the sugar latexes is inversely proportional to the concentration of the anionic emulsifier (sodium dodecyl sulphate, SDS) and the non‐ionic one (alkyl polyglucoside, APG). It was also found that D is independent of the concentration of either the water‐soluble initiator (potassium persulfate, KPS), or the oil‐soluble initiator (2,2′‐azobisisobutyronitrile, AIBN). The rate of mini‐emulsion polymerization is lower in comparison with the conventional emulsion polymerization under the same conditions. The polymerization rate (R_p) and the total number of particles (N_p) are proportional to the 0.72th and 0.93th power of the SDS, and to the 1.40th and 2.22th of the APG concentration. Following reaction orders, 0.79/0.06 were obtained for R_p/N_p versus the concentration of KPS, and 0.22/?0.01 for AIBN, respectively. Copyright © 2004 John Wiley & Sons, Ltd.     

Emulsifier-free emulsion copolymerization of styrene and butyl acrylate. I. Kinetic studies in the absence of surfactant

Soapless emulsion copolymerization of styrene (S) and n-butyl acrylate (BuA) has been investigated using two types of initiator and different comonomer feed mixtures. When using K₂S₂O₈ as initiator, the particle size and size distribution of the final latexes (500 nm and 1.003, respectively) is not significantly affected by the comonomer feed composition, whereas the molecular weight and surface characteristics were found to sharply change at high butyl acrylate content. Based on the most probable particle nucleation mechanism and type of chain termination in the monomer swollen particles, a tentative explanation of these results has been proposed. Replacing persulfate by a carboxylic initiator (4-4′-azobiscyanopentanoic acid) results in the formation of stable particles as α observed with the persulfate, provided the aqueous phase pH is fixed in between 6 and 7. Results on the initiator residue location as a function of the conversion point out that the particle flocculation mechanism is strongly significant in the preparation of such latexes.     

The preparation of sterically stabilized polymer dispersions

The emulsion polymerizations of styrene (St) and butyl acrylate (BA) stabilized by nonionic polyoxyethylene type emulsifiers did not show the long stationary rate interval. This was discussed in terms of two opposing effects: 1) the decreased monomer concentration at the reaction loci due to the depletion of monomer droplets or depressed monomer droplet degradation and 2) the increased number of polymer particles with increasing conversion. The continuous particle nucleation is attributed to the continuous release of emulsifier from the emulsifier saturated monomer droplets and/or the presence of monomer swollen micelles (microdroplets). The limited particle flocculation operative at lower emulsifier concentrations increases the nonstationary-state polymerization. The particle agglomeration is accompanied by the increased reaction order x (N_p vs. [E]^x) above 0.6. The increased uniformity of monomer emulsion stabilized by Tween 20 by homogenization of monomer emulsion increased the final conversion and the polymerization rate as well. The polymerization rate vs. conversion curve of the homogenized emulsion characterized with broader stationary rate interval reminds the four rate intervals system typical for miniemulsion. The accumulation of polymer and nonionic emulsifier within the monomer phase preserves the monomer droplets up to high conversion. The decreased monomer droplet degradation rises the monomer-starved condition or the depressed transport of both monomer and emulsifier to the reaction loci.     

Radical polymerization in homogenized butyl acrylate emulsion

The addition of a small amount of monomer strongly decreased the clouding temperature of nonionic emulsifier (Tween 20). The clouding temperature of the Tween 20 aqueous solution was independent of emulsifier concentration but it strongly varied in the presence of monomer. The decreased cloud temperature was attributed to the penetration of monomer molecules into the interfacial layer that increased the flocculation of microdroplets (monomer-swollen micelles). The surface tension of homogenized ((mini)emulsion) butyl acrylate aqueous emulsion was much smaller than that estimated at or above CMC of Tween 20. The polymerization rate vs. conversion curve of the (mini)emulsion deviates from the three rate intervals typical for the emulsion polymerisation. The shape of the rate-conversion curve reminds more the four rate intervals curve. Interval 2 is overlapped with the initial maximal rate and rate shoulder at higher conversion. The initial maximal polymerization rate (R_p,max,1) is attributed to the abrupt increase in polymer particles, the polymerization under monomer saturated condition and emulsifier containing peroxide groups (Tw_peroxid 20). The rate of emulsion polymerization of BA initiated by ammonium peroxodisulphate (APS) is ca. by one order of magnitude larger than that of blank polymerization (without APS). The second maximal rate (rate shoulder) can result from the gel effect. The more pronounced increase in R_p,max,1 with Tw 20 concentration supports the presence of peroxide groups. The slight dependence of R_p,max,2 on [Tw 20] for both APS and DBP (dibenzoyl peroxide) is discussed in terms of the depressed radical entry rate into the close packed surface later of polymer particles. The low activation energy is attributed to the decreased barrier for entering radicals into the polymer particles with increasing temperature. This is more pronounced with the accumulation of covalently bound emulsifier moieties (resulting from Tw_peroxid 20) at the particle surface. The ratio of the final number of polymer particles to the initial number of monomer droplets (N_p/N_drop) promotes the partial monomer droplet nucleation. The dye approach indicates that the degree of depletion of monomer droplets decreases from the classical emulsion polymerization to the polymerization in pre-homogenized emulsions and the emulsion polymerization with a prolonged-emulsification interval.     

Semibatch emulsion polymerization of methyl methacrylate using different polyurethane particles

Aqueous acrylic‐polyurethane (AC–PU) hybrid emulsions were prepared by semibatch emulsion polymerization of methyl methacrylate (MMA) in the presence of four polyurethane (PU) dispersions. The PU dispersions were synthesized with isophorone diisocyanate (IPDI), 1000 and 2000 molecular weight (MW) poly(neopentyl) adipate, 1000 MW polytetramethyleneetherglycol, butanediol (BD), and dimethylol propionic acid (DMPA). MMA was added in the monomer emulsion feed. We studied the effect of the use of different PU seed particles on the rate of polymerization, the particle size and distribution, the number of particles, and the average number of radicals per particle. The PU rigidity was controlled by varying the polyol chemical structure, the polyol MW (M_n), and by adding BD. The monomer feed rate was varied to study its influence on the process. It was observed that the PU particles that had been prepared with a higher MW polyol swelled better with MMA before the monomer‐starved conditions occurred. There seemed to be no significant discrepancies between the series with different PU seeds in the monomer‐starved conditions. The overall conversion depended on the monomer addition rate, and the polymerization rate acquired a constant value that was comparable to the value of the monomer addition rate. The instantaneous conversion increased slightly. The average particle size increased, and the total particle number in the reactor was constant and similar to the number of PU particles in the initial charge. The average number of radicals per particle increased. The differences between the system with a constant particle number and average number of radicals per particle and the system with a fixed radical concentration are discussed. The semibatch emulsion polymerization of MMA in the presence of PU particles studied was better compared to the system with a fixed radical concentration. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 844–858, 2005     

Preparation of poly(vinyl chloride) latexes by polymerization of stabilized monomer droplets

Poly(vinyl chloride) latexes have been prepared by polymerization in micron and submicron sized monomer droplets. Monomer emulsions with excellent long time stability were obtained by diffusional swelling of vinyl chloride monomer into preformed, stable polydisperse pre-emulsions of water-insoluble oils or monodisperse, oligomer styrene seed particles. It was found that the size and size distribution of the final latex particles were determined by those of the parent monomer emulsions. Except for the secondary particles formed during polymerization, the size and size distributions of the latex particles were found to be com-parable to those of the monomer emulsions employed, indicating a complete nucleation of the parent emulsion droplets. The extent of secondary particle formation was found to be very dependent upon the emulsifier concentration as well as on the type and amount of initiator used. © 1995 John Wiley & Sons, Inc.     

Multistep and semibatch nitroxide‐mediated controlled free‐radical emulsion polymerization: A significant step toward conceivable industrial processes

Nitroxide‐mediated emulsion polymerizations of n‐butyl acrylate and styrene were performed with a monofunctional, water‐soluble alkoxyamine initiator and a difunctional one. Two different processes were applied, either in two steps or under semibatch conditions. In particular, the polymerization times were strongly reduced, while high conversions and good control over the polymer characteristics were maintained. In all cases, stable latexes were recovered; with the difunctional initiator in particular, they exhibited small particles and narrow particle size distributions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4142–4153, 2006     

Preparation of poly(N-isopropylmethacrylamide) latexes kinetic studies and characterization

Thermosensitive crosslinked polymer latexes have been synthesized by precipitation polymerization of N-isopropylmethacrylamide (NIPMAM) as a main monomer, methylene bis-acrylamide (MBA) as a crosslinker, and potassium persulfate (KPS) as the initiator. Polymerizations kinetics were first investigated by studying both the influence of crosslinker (MBA) and initiator (KPS) concentrations and temperature effects on the polymerization conversion, the particle size, and water-soluble polymer (WSP) as a function of time. Particle size analysis by Scanning Electron Microscopy (SEM) showed that a short nucleation step afforded the synthesis of highly monodispersed latexes. In addition, a strong dependence of WSP formation on MBA and KPS concentration and polymerization temperature was found, as well. Comparison of particle size by SEM and quasielastic light scattering clearly evidenced the dramatic effect of temperature on particle size. Lower critical solubility temperatures (LCST) of latexes were determined and compared. Finally, based on these results, the mechanism of particle formation in this polymerization process is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1823–1837, 1999     

Role of grafting in the emulsion polymerization of vinyl acetate with poly(vinyl alcohol) as an emulsifier. I. Effect of the degree of blockiness on the kinetics and mechanism of grafting

The role of grafting in particle nucleation during the emulsion polymerization of vinyl acetate with partially hydrolyzed poly(vinyl alcohol) (PVA) as an emulsifier and potassium persulfate as an initiator was investigated. The polymerizations were carried out in batch with a low solids (10%) recipe. An automated reaction calorimeter (Mettler RC1) was used for the direct monitoring of the kinetics of emulsion polymerizations with three medium molecular weight PVAs differing in their degrees of blockiness (Poval 217EE > 217E > 217). Smith–Ewart case 1 kinetics (average number of free radicals per particle < 0.5) were followed in all cases, and no constant rate in interval II was observed. Contrary to what was expected, a nonlinear relationship was observed between the rate of polymerization (R_p) and the number of particles (N_p). At R_{p max,} N_p (217E) > N_p (217EE) > N_p (217), and the final N_p was independent of the degree of blockiness of PVA. The particle size distributions were broad (particle diameter = 20–100 nm) and bimodal. On the basis of these data, we concluded that particle nucleation was continuous and was accompanied by extensive limited aggregation during the particle growth stages. The evolution of the amounts of grafted PVA and poly(vinyl acetate) (PVAc) were determined in polymerizations employing the two PVAs differing the most in blockiness (Poval 217EE and 217). The grafted PVAc followed similar profiles, increasing with conversion, particularly near the end of the two reactions. The amounts of grafted PVAc were about the same in the final latexes (37–39%). In contrast, the grafting of PVA was nearly complete by the time monomer droplets had disappeared in each reaction (25% conversion). However, the extent of grafting differed significantly, with the blockier PVA having about one‐third the grafting of the more random PVA (～10% vs ～30%). In these low solids recipes, grafting appeared to be primarily a solution event, occurring predominantly in the aqueous phase and not at the particle/water interface, as was previously speculated. The PVAc grafts grew until the molecules became water‐insoluble and precipitated, forming polymer particles. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3633–3654, 2001     

On the emulsion polymerization of styrene in the presence of a nonionic emulsifier

The batch emulsion polymerization kinetics of styrene (St) initiated by a water-soluble peroxodisulfate in the presence of a nonionic emulsifier was investigated. The polymerization rate versus the conversion curves showed two nonstationary rate intervals, two rate maxima, and Smith–Ewart Interval 2 (nondistinct). The rate of polymerization and number of nucleated polymer particles were proportional to the 1.4th and 2.4th powers, respectively, of the emulsifier concentration. Deviation from the micellar nucleation model was attributed to the low water solubility of the emulsifier, the low level of the micellar emulsifier, and the mixed modes of particle nucleation. In emulsion polymerizations with a low emulsifier concentration, the number of radicals per particle and particle size increased with increasing conversion, and the increase was more pronounced at a low conversion. By contrast, in emulsion polymerizations with a high emulsifier concentration, the number of radicals per particle decreased with increasing conversion. This is discussed in terms of the mixed models of particle nucleation, the gel effect, and the pseudobulk kinetics. The formation of monodisperse latex particles was attributed to coagulative nucleation and droplet nucleation for the polymerizations with low and high emulsifier concentrations, respectively. The effects of the continuous release of the emulsifier from nonmicellar aggregates and monomer droplets, the close-packing structure of the droplet surface, and the hydrophobic nature of the emulsifier on the emulsion polymerization of St are discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4422–4431, 1999