Synthesis and characterization of new soluble aromatic polyamides derived from 1,4‐Bis(4‐carboxyphenoxy)‐2, 5‐di‐tert‐butylbenzene

Aromatic polyamides based on a novel bis(ether‐carboxylic acid) were synthesized by the direct phosphorylation condensation method. 1,4‐Bis(4‐carboxyphenoxy)‐2,5‐di‐tert‐butylbenzene was combined with various diamines containing flexible linkages and side substituents to render a set of eight novel aromatic polyamides. The polymers were produced with high yields and moderate to high inherent viscosities (0.49–1.32 dL/g) that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 31,000–80,000 and 19,000–50,000, respectively. Except for a single example, the polyamides were essentially amorphous and soluble in a variety of common solvents such as cyclohexanone, dioxane, and tetrahydrofuran. They showed glass‐transition temperatures of 250–295 °C (by differential scanning calorimetry) and 10% weight loss temperatures above 460 °C, as revealed by thermogravimetric analysis in nitrogen. Polymer films, obtained by casting from N,N‐dimethylacetamide solutions, exhibited good mechanical properties, with tensile strengths of 83–111 MPa and tensile moduli of 2.0–2.2 GPa. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 475–485, 2001     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Synthesis and characterization of new soluble polyamides derived from 2,6-bis(4-aminophenyl)-3,5-dimethyltetrahydro-4H-pyran-4-one

A new oxypyrone diamine, 2,6-bis(4-aminophenyl)-3,5-dimethyltetrahydro-4H-pyran-4-one (DAPP), was prepared from 4-nitrobenzaldehyde and 3-oxa-n-pentane in a two-step reaction with a high yield and a high purity. Aromatic polyamides were obtained from this novel condensation monomer and several diacid chlorides through the conventional low-temperature solution method in N,N-dimethylacetamide. Polycondensation results were consistent with a high reactivity for DAPP because high yields and high molecular weight polyamides were obtained with inherent viscosities up to 1.8 dL/g. The reactivity of DAPP was also estimated with theoretical calculations from computer programs for molecular simulation, with orbital and charge factors considered. The polymers showed improved solubility in organic solvents, relative to conventional wholly aromatic polyamides, and high glass-transition temperatures (from differential scanning calorimetry) over 270 °C. However, the thermal resistance, as estimated by thermogravimetric analysis, was lower than that of conventional aromatic polyamides; nevertheless, decomposition temperatures well beyond 300 °C were observed in nitrogen and air. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1825–1832, 2001     

Synthesis and characterization of new soluble aromatic polyamides from diaminotetraphenylimidazolin-2-one and various aromatic dicarboxylic acid chlorides

Novel aromatic polyamides, having inherent viscosities of 0.76-2.31 dL/g, were synthesized by the low temperature solution polycondensation of a new highly phenylated diamine monomer having an imidazolinone group, 1,3-bis(4-aminophenyl)-4,5-diphenylimidazoline-2-one (TPIDA), with various aromatic diacid chlorides. All the polymers were amorphous, and most of the polyamides were readily soluble in organic solvents such as N-methyl–2-pyrrolidone, N,N-dimethylacetamide (DMAc), and m-cresol. Flexible and tough films could be prepared from the DMAc solutions of these soluble aromatic polyamides. The glass transition temperatures and 10% weight loss temperatures under nitrogen of the polyamides were in the range of 275–315°C and 430–505°C, respectively. © 1995 John Wiley & Sons, Inc.     

Synthesis and properties of soluble aromatic polyamides derived from 2,2′‐bis(4‐carboxyphenoxy)‐9,9′‐spirobifluorene

The synthesis of a new bis(ether carboxylic acid), 2,2′‐bis(4‐carboxyphenoxy)‐9,9′‐spirobifluorene, in which two orthogonally arranged carboxyphenoxyfluorene entities are connected through an sp³ carbon atom (the spiro center), is reported. The direct phosphorylation polycondensation of this diacid monomer with various aromatic diamines yields aromatic polyamides containing 9,9′‐spirobifluorene moieties in the main chain. The presence of the spiro segment restricts the close packing of the polymer chains and decreases interchain interactions, resulting in amorphous polyamides with enhanced solubility, and high glass‐transition temperatures and good thermal stability are maintained through controlled segmental mobility. The glass‐transition temperatures of these polyamides are in the range of 234–306 °C, with 10% weight losses occurring at temperatures above 530 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1160–1166, 2003     

Synthesis and characterization of new aromatic polyamides bearing crown ethers or their dipodal counterparts in the pendant structure. I. Benzo‐12‐crown‐4 and ortho‐bis(2‐ethoxyethoxy)benzene

Two novel isophthalic diacid‐based monomers have been synthesized by inclusion in ring position 5 of a functionalized benzoylamine moiety. The functionalization includes a 12‐crown‐4 ether group fused with the benzene subunit and a dipodand substructure, formally a disubstitution of the benzene ring, with two sequences of ethyl‐terminated ethylene oxide units, which represent the open‐chain counterpart of the alicylic crown moiety. The polycondensation of the two diacids with five aromatic diamines yielded 10 new polyamides with crown or podand pendant substructures. The polyamides had previously been chemically characterized by NMR, IR, and elemental analysis. The polymers showed high glass transition temperatures of up to 349 °C, good thermal stability (T_{donset, N2} ≈ 400 °C), and improved solubility in organic solvents. The presence of acyclic or alicyclic oxyethylene sequences as crown ether or podand substructures and an additional amide side group per repeat unit made the polymers essentially amorphous and improved their water absorption ability in comparison with nonsubstituted polyamides. Water uptake values as high as 12% were observed at 65% relative humidity. All the polyamides showed a good film‐forming ability, and the mechanical properties of these films are considered to be satisfactory for experimental aromatic polyamides. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2270–2281, 2006     

Syntheses and properties of novel fluorinated polyamides based on a bis(ether‐carboxylic acid) or a bis(ether amine) extended from bis(4‐hydroxyphenyl)phenyl‐2,2,2‐trifluoroethane

Two series of novel fluorinated aromatic polyamides were prepared from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane with various aromatic dicarboxylic acids with the phosphorylation polyamidation technique. These polyamides had inherent viscosities ranging from 0.51 to 1.54 dL/g that corresponded to weight‐average and number‐average molecular weights (by gel permeation chromatography) of 36,200–80,000 and 17,200–64,300, respectively. All polymers were highly soluble in aprotic polar solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some could even be dissolved in less‐polar solvents like tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 76–94 MPa and initial moduli of 1.70–2.22 GPa. Glass‐transition temperatures (T_g's) and softening temperatures of these polyamides were observed in the range of 185–268 °C by differential scanning calorimetry or thermomechanical analysis. Decomposition temperatures (T_d's) for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. Almost all the fluorinated polyamides displayed relatively higher T_g and T_d values than the corresponding nonfluorinated analogues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 420–431, 2003     

Synthesis and characterization of new organosoluble polyamides derived from bis[4‐(4‐carboxyphenoxy) phenyl]diphenylmethane

A new dicarboxylic acid containing a diphenylmethylene linkage, bis[4‐(4‐carboxyphenoxy)phenyl]diphenylmethane (BCAPD), was prepared from bis(4‐hydroxphenyl)diphenylmethane and p‐fluorobenzonitrile via an aromatic nucleophilic substitution reaction followed by hydrolysis. A series of novel polyamides were prepared by the direct polycondensation of BCAPD and various aromatic diamines. The polymers were produced with moderate to high inherent viscosities of 0.80–0.85 dL g^?1. Nearly all the polymers were readily soluble in polar solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide, in less polar solvents such as pyridine and cyclohexanone, and in tetrahydrofuran. All the polymers were amorphous, and the polyamide films had a tensile strength and a tensile modulus greater than 80 MPa and 2.0 GPa, respectively. These polyamides had glass‐transition temperatures between 249 and 274 °C, and their temperatures at a 10% weight loss were 477–538 and 483–540 °C in nitrogen and air atmospheres, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1156–1161, 2001     

Synthesis,characterization, and properties of new sequenced poly(ether amide)s based on 2‐(4‐aminophenyl)‐5‐aminobenzimidazole and 2‐(3‐aminophenyl)‐5‐aminobenzimidazole

A set of new aromatic poly(ether amide)s containing benzimidazole groups and ethylene oxide sequences of different lengths were synthesized and characterized. The new polymers were prepared from two benzimidazole diamines, 2‐(4‐aminophenyl)‐5‐aminobenzimidazole and 2‐(3‐aminophenyl)‐5‐aminobenzimidazole, and various oligo(ethylene oxide)dibenzoyl chlorides. They exhibited good solubility in polar aprotic solvents and glass‐transition temperatures in the range of 125–300 °C (the longer the ethylene oxide spacer was, the lower the glass‐transition temperature was). The new polyamides were essentially amorphous, as observed by X‐ray diffraction measurements and confirmed by differential scanning calorimetry measurements, by means of which no melting endotherm was observed in any case. The decomposition temperatures, as revealed by thermogravimetric analysis in nitrogen, were about 400 °C for all of them, regardless of the length of the ethylene oxide content or the phenylene ring orientation (meta or para) of the diamine moiety. The number of ethylene oxide linkages per repeat unit also determined the water uptake. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1414–1423, 2006     

Synthesis and characterization of highly soluble wholly aromatic polyamides containing both furanyl and phenyl units

This paper presents the synthesis and characterization of two series of polymeric compounds comprising eight furan-based polyamides prepared via melt polycondensation at low temperatures using various combinations of five aromatic raw materials. The chemical and physical structures and thermal stabilities of the obtained polyamides were investigated by various characterization methods. In addition, the polyamides were subjected to solubility testing in five common organic solvents. The results showed that the proposed furan-based polyamides possessed thermal stabilities similar to those of conventional high-performance aromatic polyamides, but with greatly improved solubility. Accordingly, the introduction of furan groups increased the solubility of the polyamides with respect to the solubility of their individual precursors, which is highly advantageous for subsequent polyamide processing and expanding their range of potential applications.     

Preparation and characterization of aromatic polyamides based on a bis(ether‐carboxylic acid) or a dietheramine extended from 1,1‐bis(4‐hydroxyphenyl)‐1‐phenylethane

Thermoplastic and organic‐soluble aromatic polyamides containing both bulky triphenylethane units and flexible ether linkages were prepared directly from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐1‐phenylethane ( III ) with various aromatic diamines or from 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐phenylethane ( V ) with various aromatic dicarboxylic diacids via triphenyl phosphite and pyridine. These polyamides had inherent viscosities ranging from 0.71 to 1.77 dL/g. All the polymers easily were dissolved in aprotic polar solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide, and some even could be dissolved in less polar solvents such as tetrahydrofuran. The flexible and tough films cast from the polymer solutions possessed tensile strengths of 89 to 104 MPa. The polyamides were thermally stable up to 460°C in air or nitrogen. Glass‐transition temperatures of these polyamides were observed in a range of 179 to 268°C via differential scanning calorimetry or thermomechanical analysis. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 247–260, 2000     

Synthesis,characterization, and properties of semifluorinated organo‐soluble new aromatic polyamides

A series of organo‐soluble new polyamides were synthesized by the direct polycondensation of different semifluorinated aromatic diamines, namely 4,4‐bis[3'‐trifluoromethyl‐4'(4“‐amino benzoxy)benzyl]biphenyl; 4,4”‐bis(aminophenoxy)‐3'3“‐trifluoromethyl terphenyl; 1,3‐bis[3'‐trifluoromethyl‐4'(4”‐amino benzoxy)benzyl]benzene; 2,6‐bis(3'‐trifluoromethyl‐p‐aminobiphenyl ether)pyridine; and 2,5‐bis(3'‐trifluoromethyl‐p‐aminobiphenyl ether)thiophene with 5‐t‐butyl‐isophthalic acid. The polymers were fully characterized by elemental analysis and IR, NMR spectroscopies. The synthesized polyamides were soluble in several organic solvents such as 1‐methyl‐2‐pyrrolidone, N,N‐dimethylformamide, N,N‐dimethylacetamide, tetrahydrofuran, and dimethyl sulfoxide at room temperature. They showed inherent viscosities of 0.42–0.63 dl/g. The polyamides exhibited weight‐average molecular weights of up to 233,000, which depended on the exact repeating unit structure. The polyamides synthesized from 4,4‐bis[3'‐trifluoromethyl‐4'(4”‐amino benzoxy)benzyl]biphenyl and 5‐t‐butyl isophthalic acid exhibited highest glass‐transition temperatures 261°C (evaluated by differential scanning calorimetry) in nitrogen. These polyamides showed good thermal stability up to 475°C for a 10% weight loss in air. The polyamides films were clear and flexible in nature with tensile strengths of up to 88 MPa, modulus of elasticity of up to 1.81 GPa, and elongations at break of up to 25%, which depended on the exact repeating unit structure. X‐ray diffraction measurements indicated that these polyamides were amorphous in nature. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and properties of aromatic polyamides based on non-, methyl-, and phenyl-substituted 4,4′-bis(1,4-phenylenedioxy)dibenzoic acids

4,4′-(1,4-Phenylenedioxy)dibenzoic acid (3), 4,4′-(2,5-tolylenedioxy)dibenzoic acid (Me-3), and 4,4′-(2,5-biphenylenedioxy)dibenzoic acid (Ph-3) were prepared by the nucleophilic substitution reaction of p-fluorobenzonitrile with hydroquinone, methylhydroquinone, and phenylhydroquinone, respectively, followed by alkaline hydrolysis. Several aromatic polyamides having inherent viscosities of 0.66–1.34 dL/g were directly prepared by a Yamazaki phosphorylation polyamidation technique from dicarboxylic acids 3, Me-3, and Ph-3, respectively, with aromatic diamines using triphenyl phosphite and pyridine as condensing agents. The solubility of methyl- or phenyl-substituted polyamides was remarkably enhanced when compared to that of nonsubstituted analogues. Most of the substituted polyamides revealed an amorphous nature and were readily soluble in a variety of organic solvents including N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), N,N-dimethylformamide, dimethyl sulfoxide, and m-cresol. Transparent, flexible, and tough films of these polymers could be cast from the DMAc or NMP solutions. These films had tensile strength of 60–100 MPa, elongation to break of 6–11%, and tensile modulus of 1.68–2.25 GPa. The glass transition temperatures (T_g) of most polyamides could be determined by differential scanning calorimetry (DSC) and were in the range of 200–232°C. Thermogravimetric analyses established that these polymers were fairly stable up to 450°C, and the 10% weight loss temperatures were recorded in the range of 458–535°C in nitrogen and 468–528°C in air atmosphere. In general, the phenyl-substituted polyamides exhibited relatively higher T_g, thermal stability, and solubility. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of aromatic polyamides based on a benzonorbornane bis(ether carboxylic acid)

A set of new aromatic polyamides containing ether and benzonorbornane units were synthesized by the direct phosphorylation polycondensation of 3,6‐bis(4‐carboxyphenoxy)benzonorbornane with various aromatic diamines. The polymers were produced in high yields and moderate to high inherent viscosities (0.64–1.70 dL/g). The polyamides derived from rigid diamines such as p‐phenylenediamine and benzidine were semicrystalline and insoluble in organic solvents. The other polyamides were amorphous and organosoluble and afforded flexible and tough films via solution casting. These films exhibited good mechanical properties, with tensile strengths of 95–101 MPa, elongations at break of 13–25%, and initial moduli of 1.97–2.33 GPa. The amorphous polyamides showed glass‐transition temperatures between 176 and 212 °C (by differential scanning calorimetry) and softening temperatures between 194 and 213 °C (by thermomechanical analysis). Most of the polymers did not show significant weight loss before 450 °C in nitrogen or in air. Some properties of these polyamides were also compared with those of homologous counterparts without the pendent norbornane groups. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 947–957, 2002     

Soluble fluorinated polyimides derived from 1,4‐ (4′‐aminophenoxy)‐2‐(3′‐trifluoromethylphenyl)benzene and aromatic dianhydrides

New fluorinated aromatic polyimides were prepared from 1,4‐(4′‐aminophenoxy)‐2‐(3′‐trifluoromethylphenyl)benzene and aromatic dianhydrides via the polycondensation of one‐step high‐temperature and two‐step thermal or chemical imidization methods. Experimental results indicated that some of the polyimides were soluble both in strong dipolar solvents (N‐methyl‐2‐pyrrolidone or N,N‐dimethylacetamide) and in common organic solvents such as tetrahydrofuran, CHCl₃, and acetone. The polyimides showed exceptional thermal and thermooxidative stability and good mechanical properties. No weight loss was detected before a temperature of 520 °C in nitrogen, and the glass‐transition temperatures ranged from 208 to 251 °C. Low dielectric constants (2.55–2.71 at 1 MHz), low refractive indices, and low water absorption were also observed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2404–2413, 2001     

Synthesis and properties of new polyamides derived from 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone by direct polycondensation

A series of new polyamides containing both sulfone and oxyethylene moieties in the polymer chain was prepared by the direct polycondensation of the diamine monomer 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone (BAEPS) and various aromatic dicarboxylic acids in N‐methyl‐2‐pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with inherent viscosities of 0.30–0.60 dl/g and identified by elemental analysis, and infrared and nuclear magnetic resonance spectra. Most of the polymers were readily dissolved in polar solvents such as NMP, dimethylsulfoxide, N,N‐dimethylacetamide, N,N‐dimethylformamide and m‐cresol at room temperature. Polymers containing rigid and symmetric p‐phenylene, naphthalene and p‐biphenylene moieties revealed a crystalline nature and showed no solubility in organic solvents. These polyamides had 10% weight loss temperatures ranging between 423 and 465 °C in nitrogen atmosphere and glass transition temperatures between 170 and 305 °C. The polymers with crystallinity nature exhibited melting endotherms (T_m) below 386 °C in differential scanning calorimetry trace. Copyright © 1999 John Wiley & Sons, Ltd.     

Synthesis and characterization of soluble fluorine‐containing polyimides based on 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene

The synthesis and properties of a class of soluble fluorine‐containing aromatic polyimides are described. Substituents of trifluoromethyl groups on the aromatic rings of paralinked aromatic ether diamine conferred the polymer prepared thereof with enhanced solubility, low‐moisture absorption, and low dielectric constants. The polyimides also exhibited exceptional thermal stability, good mechanical properties, and excellent hygrothermal resistance. These outstanding combined features ensure the polymers are desirable candidate materials for advanced microelectronics applications. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2581–2590, 2001     

Synthesis and properties of novel soluble polyamides having ether linkages and laterally attached p‐terphenyl units

A new ether‐bridged aromatic dicarboxylic acid, 2′,5′‐bis(4‐carboxyphenoxy)‐p‐terphenyl ( 3 ), was synthesized by the aromatic fluoro‐displacement reaction of p‐fluorobenzonitrile with 2′,5′‐dihydroxy‐p‐terphenyl in the presence of potassium carbonate, followed by alkaline hydrolysis. A set of new aromatic polyamides containing ether and laterally attached p‐terphenyl units was synthesized by the direct phosphorylation polycondensation of diacid 3 with various aromatic diamines. The polymers were produced with high yields and moderately high inherent viscosities (0.44–0.79 dL/g). The polyamides derived from 3 and rigid diamines, such as p‐phenylenediamine and benzidine, and a structurally analogous diamine, 2′,5′‐bis(4‐aminophenoxy)‐p‐terphenyl, were semicrystalline and insoluble in organic solvents. The other polyamides were amorphous and organosoluble and could afford flexible and tough films via solution casting. These films exhibited good mechanical properties, with tensile strengths of 91–108 MPa, elongations to break of 6–17%, and initial moduli of 1.95–2.43 GPa. These polyamides showed glass‐transition temperatures between 193 and 252 °C. Most of the polymers did not show significant weight loss before 450 °C, as revealed by thermogravimetric analysis in nitrogen or in air. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4056–4062, 2004     

Synthesis and characterization of new soluble polyamides from 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane and various diamines

A new dicarboxylic acid monomer, 1,1‐bis[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane, bearing a pendent tert‐butylcyclohexylidene group was prepared in three steps from 4‐tert‐butylcyclohexanone. The monomer was reacted with various diamines to produce a series of new polyamides with triphenyl phosphite and pyridine as condensing agents. These polyamides were produced with inherent viscosities of 0.74 to 1.02 dL g⁻¹. All the polymers were characterized by X‐ray diffraction that revealed this amorphous nature. These polymers exhibited excellent solubility in a variety of solvents. Almost all the polymers could be dissolved in N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, dimethyl sulfoxide, pyridine, and even in tetrahydrofuran and cyclohexanone. These polymers showed glass‐transition temperatures between 223 and 256 °C and decomposition temperatures at 10% weight loss ranging from 468 to 491 °C and 469 to 498 °C in nitrogen and air atmospheres, respectively. Transparent, tough, and flexible films of these polymers were cast from the DMAc solutions. These polymer films had tensile strengths ranging from 76 to 99 MPa, elongations at break from 7 to 19%, and initial moduli from 2.1 to 2.7 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 797–803, 2000     

Synthesis and characterization of polyimides from bis(3‐aminophenyl)‐4‐(1‐adamantyl)phenoxyphenyl phosphine oxide

A novel diamine, bis(3‐aminophenyl)‐4‐(1‐adamantyl)phenoxyphenyl phosphine oxide (mDAATPPO), was synthesized via the Williamson ether reaction of 4‐(1‐adamantyl)phenol and bis(3‐nitrophenyl)‐4‐fluorophenyl phosphine oxide, followed by reduction. The phenol group was prepared by the Friedel–Crafts reaction of 1‐bromoadamantane and phenol, whereas the phosphine oxide group was synthesized by the Grignard reaction of 1‐bromo‐4‐fluorobezene and diphenyl phosphinic chloride, followed by nitration. The monomer and its intermediate compounds were characterized with Fourier transform infrared, NMR, and melting‐point apparatus. The monomer was then used to prepare polyimides with 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, 4,4′‐oxydiphthalic dianhydride, and pyromellitic dianhydride by the conventional two‐step synthesis: the preparation of poly(amic acid) followed by solution imidization. The molecular weights of the polyimides were controlled to 20,000 g/mol by off‐stoichiometry, and the synthesized polyimides were characterized with Fourier transform infrared, NMR, gel permeation chromatography, thermogravimetric analysis, and differential scanning calorimetry. In addition, the solubility, intrinsic viscosity, dielectric constant, and birefringence of the polyimides were evaluated. Novel polyimides with mDAATPPO exhibited good solubility, high glass‐transition temperatures (290–330 °C), excellent thermal stability (>500 °C), low dielectric constants (2.77–3.01), low refractive indices, and low birefringence values (0.0019–0.0030). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2567–2578, 2006