Molecular orientation and mechanical anisotropy of polypropylene sheet containing N,N′‐dicyclohexyl‐2,6‐naphthalenedicarboxamide

Effect of mixing and processing conditions at T‐die extrusion on the structure and mechanical properties is studied for isotactic polypropylene (PP) containing a small amount of β‐form nucleating agent, N,N′‐dicyclohexyl‐2,6‐naphthalenedicarboxamide. It is found that trigonal β crystals are predominantly formed in the extruded samples containing the nucleating agent irrespective of the mixing and processing conditions, leading to the marked mechanical toughness. On the contrary, the molecular orientation is significantly affected by the mixing and processing conditions. In particular, it should be noted that PP molecules in the extruded sheet which was mixed at high temperature (260 °C) and extruded at low temperature (200 °C) orient perpendicular to the applied flow direction. As a result, the sheet shows anomalous mechanical anisotropy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 424–433, 2009     

Crystalline structure and morphology of biaxially oriented polyamide‐11 films

The effect of the uniaxial and biaxial stretching and subsequent solution annealing of extrusion‐cast polyamide‐11 films on the crystalline structure and morphology was investigated with differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), Fourier transform infrared spectroscopy, and small‐angle X‐ray scattering (SAXS). The extrusion‐cast polyamide‐11 films exhibited elevations in the glass‐transition and cold‐crystallization temperatures with a constant crystallinity and a constant melting point during aging under room conditions (20–26 °C and 20–31% relative humidity). WAXD and SAXS suggested that chain‐folded lamellae of coexisting α‐ and β‐crystals existed in all the stretched polyamide‐11 films. WAXD pole figures indicated that hydrogen bonds in the hydrogen‐bonded sheets of these two crystalline forms apparently formed between antiparallel chain molecules. The unit cell parameters [a = 9.52 Å, b = 5.35 Å, c = 14.90 Å (chain axis), α = 48.5°, β = 90°, and γ = 74.7° for a triclinic α form and a = 9.52 Å, b = 14.90 Å (chain axis), c = 4.00 Å, α = 90°, β = 67.5°, and γ = 90° for a monoclinic β form] for polyamide‐11 crystals were proposed according to the results of this study and the results of previous investigators. The unit cell parameters of the stretched extrusion‐cast polyamide‐11 films varied, depending on the stretching conditions (the stretch temperature and stretch ratio). As the stretch temperature and stretch ratio were increased, the crystal became more similar to the form described previously and was accompanied by an increase in the long spacing of crystalline lamellae. Annealing the stretched films in a boiling 20% formic acid solution made slightly more perfected crystals. The hydrogen‐bonding α(010) + β(002) planes, which are nearly parallel to both amide group planes and zigzag methylene sequence planes of the biaxially stretched films were found to be parallel to the film surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2624–2640, 2002     

Effects of the oriented mesophase on the cold crystallization of syndiotactic polystyrene and its blend with poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The effects of molecular orientation on the crystallization and polymorphic behaviors of syndiotactic polystyrene (sPS) and sPS/poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) blends were studied with wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry. The oriented amorphous films of sPS and sPS/PPO blends were crystallized under constraint at crystallization temperatures ranging from 140 to 240°C. The degree of crystallinity was lower in the cold‐crystallized oriented film than in the cold‐crystallized isotropic film. This was in contrast to the case of the cold crystallization of other polymers such as poly(ethylene terephthalate) and isotactic polystyrene, in which the molecular orientation induced crystallization and accelerated crystal growth. It was thought that the oriented mesophase was obtained in drawn films of sPS and that the crystallization of sPS was suppressed in that phase. The WAXD measurements showed that the crystal phase was more ordered in an sPS/PPO blend than in pure sPS under the same annealing conditions. The crystalline order recovered in the cold‐crystallized sPS/PPO blends in comparison with the cold‐crystallized pure sPS because of the decrease in the mesophase content. The crystal forms depended on the crystallization temperature, blend composition, and molecular orientation. Only the α′‐crystalline form was obtained in cold‐crystallized pure sPS, regardless of molecular orientation, whereas α′, α″, and β′ forms coexisted in the cold‐crystallized sPS/PPO blends prepared at higher crystallization temperatures (200–240°C). The β′‐form content was much lower in the oriented sPS/PPO blend than in the isotropic blend sample at the same temperature and composition. It was concluded that the oriented mesophase suppressed the crystallization of the stable β′ form more than that of the metastable α′ and α″ forms during the cold crystallization of sPS/PPO blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1665–1675, 2003     

2′‐De­oxy‐2‐fluoro­tubercidin

In the title compound [systematic name: 7‐(2‐de­oxy‐β‐d ‐erythro‐pentofuranos­yl)‐2‐fluoro‐7H‐pyrrolo[2,3‐d]pyrimidin‐2‐amine], C₁₁H₁₃FN₄O₃, the conformation of the N‐glycosylic bond is between anti and high‐anti [χ = −110.2 (3)°]. The 2′‐deoxy­ribofuranosyl unit adopts the N‐type sugar pucker (₄T³), with P = 40.3° and τ_m = 39.2°. The orientation of the exocyclic C4′—C5′ bond is −ap (trans), with a torsion angle γ = −168.39 (18)°. The nucleobases are arranged head‐to‐head. The crystal structure is stabilized by four inter­molecular hydrogen bonds of types N—H⋯N, N—H⋯O and O—H⋯O.     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Melt‐crystallized, low molecular weight poly(L ‐lactic acid) (PLLA) consisting of α crystals was uniaxially drawn by solid‐state extrusion at an extrusion temperature (T_ext) of 130–170 °C. A series of extrusion‐drawn samples were prepared at an optimum T_ext value of 170 °C, slightly below the melting temperature (T_m) of α crystals (～180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide‐angle X‐ray scattering (WAXD), and small‐angle X‐ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid‐state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of α and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010)_α and (003)_β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial α form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid‐state extrusion of melt‐crystallized, low molecular weight PLLA slightly below T_m. The structure and properties of the α‐ and β‐form crystals were also studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 95–104, 2002     

Superdrawing of polytetrafluoroethylene nascent powder by solid‐state coextrusion

A film of nascent powder of polytetrafluoroethylene (PTFE), compacted below the ambient melting temperature (T_m, 335 °C), was drawn by two‐stage draw techniques consisting of a first‐stage solid‐state coextrusion followed by a second‐stage solid‐state coextrusion or tensile draw. Although the ductility of extrudates was lost for the second‐stage tensile draw at temperatures above 150 °C due to the rapid decrease in strength, as previously reported, the ductility of extrudates increased with temperature even above 150 °C when the second‐stage draw was made by solid‐state coextrusion, reflecting the different deformation flow fields in a free space for the former and in an extrusion die for the latter. Thus, a powder film initially coextruded to a low extrusion draw ratio (EDR) of 6–20 at 325 °C was further drawn by coextrusion to EDRs up to ～?400 at 325–340 °C, near the T_m. Extremely high chain orientation (f_c = 0.998 ± 0.001), crystallinity (96.5 ± 0.5)%, and tensile modulus (115 ± 5 GPa at 24 °C, corresponding to 73% of the X‐ray crystal modulus) were achieved at high EDRs. Despite such a morphological perfection and a high modulus, the tensile strength of a superdrawn tape, 0.48 ± 0.03 GPa, was significantly low when compared with those (1.4–2.3 GPa) previously reported by tensile drawing above the T_m. Such a low strength of a superdrawn, high‐modulus PTFE tape was ascribed to the low intermolecular interaction of PTFE and the lack of intercrystalline links along the fiber axis, reflecting the initial chain‐extended morphology of the nascent powder combined with the fairly high chain mobility associated with the crystal/crystal transitions at around room temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3369–3377, 2006     

Biodegradable ultra high strength poly(L-lactide) rods for bone fixation

The hydrostatic molecular orientation technique was used to explore the highest mechanical improvements achievable for poly-L-lactide (PLLA). The mechanical attributes of these materials designed for bone fracture fixation devices, i.e. bending strength and modulus were measured and compared with those prepared by stretching method. The starting samples were prepared by conventional melt extrusion at 200 °C followed by hydrostatic extrusion at 140 °C using glycerin filled extruder. Uniaxially stretched rods were prepared by drawing in silicon oil at 120 °C. The physical properties of these rods are inadequate as mechanical supports in the dynamic healing process of the bone. Moreover, they underwent a marked strength deterioration when immersed in aqueous buffered solution for 90 days. On the other hand, the hydrostatic extrusion technique produced rods with progressively higher bending strength that showed only a small drop after 90 days hydrolytic degradation. Micrographs suggested a superior molecular orientation and packing, which could be associated with the improved performance. The hydrostatic extrusion technique proved to be a safe and effective approach for strengthening biodegradable polymeric materials for dynamic mechanical support in orthopedic medical devices.     

A novel phosphorus‐containing thermotropic liquid crystalline poly(ester‐imide) with high flame retardancy

A novel phosphorus–nitrogen thermotropic liquid crystalline poly(ester‐imide) (PN‐TLCP) derived from p‐acetoxybenzoic acid (ABA), terephthalic acid (TPA), acetylated 2‐(6‐oxide‐6H‐dibenz<c,e><1,2>oxa phosphorin‐ 6‐yl)‐1,4‐dihydroxy phenylene (DOPO‐AHQ) and N,N'‐hexane‐1,6‐diylbis(trimellitimide) was prepared by melt transesterification. The chemical structure, the mesophase behavior, and the thermal properties of the copolymer were investigated with Fourier transform infrared spectroscopy (FTIR), proton nuclear magnetic resonance spectroscopy (¹H NMR), elemental analysis, wide‐angle X‐ray diffraction (WAXD), hot‐stage polarized light microscopy (PLM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). PN‐TLCP exhibited a nematic mesophase with a strong birefringence at a low and broad mesomorphic temperature ranging from 220 to 350°C, an initial flow temperature as low as about 190°C and a glass transition temperature of about 160°C. PN‐TLCP has also good thermal stability, high char residues and excellent flame retardancy (limiting oxygen index, LOI = 71 and UL‐94 V‐0 rating). Copyright © 2009 John Wiley & Sons, Ltd.     

Extrusion,fiber formation,and characterization of thermotropic copolyesters

The flow behavior and the effect of the spinning conditions on the fiber properties and structure of poly(ethylene terephthalate) modified with 60 mol% p-hydroxybenzoic acid (PET/60PHB) were investigated. PET and its copolyesters with 28 and 80 mol% PHB were used as control samples. The melt of PET/60PHB at temperatures above 265°C exhibited extremely low viscosity and low flow activation energy. High birefringence, indicating the presence of a mesophase, was observed between 265 and 300°C on a hot-stage polarizing light microscope. The maximum tensile strength and initial modulus, 438 MPa and 37 GPa, respectively, were obtained at 275°C for a 0.69 IV polymer. The fiber strength and modulus were significantly lowered when extrusion was conducted at temperatures below 265°C. The fiber properties could also be improved when a high extrusion rate and/or a high draw down ratio was used. Scanning electron microscopy revealed that the fibers spun at temperatures above 265°C had a well-developed, highly oriented fibrillar structure. The fibers spun at lower temperatures, however, were poorly oriented and nonfibrillar in character. The high orientation and superior mechanical performance achieved at high temperatures were attributed to the presence of the nematic mesophase in the polymer melt.     

Molecular composites composed of castor oil‐modified poly(ε‐caprolactone) and self‐assembled hydroxystearic acid fibers

After (R)‐12‐hydroxystearic acid (HSA) was mixed at 100 °C with the castor oil‐modified poly(ε‐caprolactone) (CO‐PCL) prepared by the ring‐opening polymerization of ε‐caprolactone in the presence of castor oil, the mixture was gradually cooled to room temperature to give a solidified CO‐PCL/HSA composite. The CO‐PCL/HSA sample showed an exothermic peak at around 67–71 °C which was lower than the melting point of HSA (76.8 °C), indicating the formation of mesogenic HSA aggregates. The rheological measurement of the CO‐PCL/HSA revealed the formation of HSA organogel at around 67–55 °C during the cooling process from the melt. Furthermore, the polarized and normal optical microscopic analyses of CO‐PCL/HSA on the cooling stage revealed that anisotropic fibrous materials are formed at around 60 °C and then the fibrous network propagated over the matrix polymer. The flexural modulus and storage modulus of the CO‐PCL/HSA composite increased with increasing HSA content. The CO‐PCL/HSA composite annealed at 60 °C for 2 h on the cooling process had a higher flexural and storage modulus than the sample without annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1281–1289, 2010     

Kinetics and mechanism of the aminolysis of O‐ethyl S‐aryl thiocarbonates in acetonitrile

The kinetics and mechanism of the reactions of O‐ethyl S‐(Z)aryl thiocarbonates with (X)benzylamines in acetonitrile at 45.0°C are studied. Relatively small values of β_X(β_nuc) = 0.6 ∼ 0.8 and β_Z (β_lg) = −0.5 ∼ −0.7 together with a negative cross‐interaction constant ρ_XZ (= −0.47) and failure of the reactivity–selectivity principle (RSP) are interpreted to indicate a concerted mechanism. The normal kinetic isotope effects (k_H/k_D = 1.3 ∼ 1.8) involving deuterated benzylamine nucleophiles suggest a hydrogen‐bonded, four‐center‐type transition state. © 2000 John Wiley & Sons, Inc. Int J Chem Kinet 32: 131–135, 2000     

Synthesis and characterization of thermotropic liquid crystalline polyurethanes from 4,4′‐bis(6‐hydroxyhexoxy) biphenyl and aliphatic diols

A series of thermotropic liquid crystalline polyurethanes (LCPUs) were synthesized by the polyaddition reactions of 2,4‐toluene diisocyanate (2,4‐TDI) with 4,4′‐bis(6‐hydroxyhexoxy)biphenyl (BHHBP) and aliphatic diol. The intrinsic viscosities of the polymers were measured by Ubbelohde viscometer, and the chemical structure was confirmed by Fourier transform infrared spectroscopy (FT‐IR). The LCPUs were examined by differential scanning calorimetry (DSC), polarized optical microscopy (POM), wide angle X‐ray diffraction (WAXD), and thermogravimetric analysis (TGA). The intrinsic viscosities were 0.56–0.83 dl/g. According to the melting point (T_m) and the isotropic temperature (T_i) of the LCPUs, the temperature range of the liquid crystalline phase became wider with increased number of methylene spacers in the polyurethane. The LCPUs exhibited a nematic phase with a threaded texture and had a wide mesophase temperature range. The decomposition temperature of the LCPUs was >300°C. On WAXD, the LCPUs give a dispersing peak at 2θ ≈ 20°, and a strong diffraction peak at 2θ ≈ 25°. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of Comonomer‐Unit Compositional Distribution on Thermal and Crystallization Behavior of Bacterial Poly[(3‐hydroxybutyrate)‐co‐(3‐mercaptopropionate)]

The physical properties of novel sulfur‐containing biopolymers, poly[(3‐hydroxybutyrate)‐co‐(3‐mercaptopropionate)]s [P(3HB‐co‐3MP)s], have been investigated in detail by¹H and ¹³C NMR spectroscopy, wide‐angle X‐ray diffraction (WAXD) analysis, DSC, and FT‐IR spectroscopy. Based on a solvent/non‐solvent (chloroform/heptane) fractionation method, an original P(3HB‐co‐3MP) sample with 3MP unit content of 16.3 mol‐% was fractionated into eight fractions with 3MP unit content ranging from 10.3 to 37.2 mol‐% and number‐average molecular weight from 0.4 × 10⁵ to 2.9 × 10⁵. The thermal and crystallization behavior were found to be greatly affected by the comonomer‐unit composition and its distribution. Furthermore, the 3MP comonomer unit was found to be included in the crystalline phase in some fractions.

     

Uniaxial Draw Of Poly(aryl-ether-ether-ketone) by solid-state extrusion

Poly(aryl-ether-ether-ketone) (PEEK) films and rods have been solid-state extruded at 154 and 310°C, respectively. The crystal orientation functions, melting behavior, density, and tensile properties of the drawn PEEK films (EDR ≤ 3.7) and rods (EDR ≤ 5.5) have been measured. As extrusion draw ratio (EDR) was increased, the c-axis orientation function, melting temperature, and tensile modulus and strength increased. Moduli up to 6.5 GPa and the strengths up to 600 MPa, 3 and 6 times the values of undrawn films, respectively, were obtained for the drawn films. The thermal expansivities along (α_‖) and perpendicular (α_?) to the draw direction of PEEK rods were measured from ?40 to +10°C. As EDR was increased, α_? increased, but α_‖ decreased. At EDRs of 3.8 and 5.5, α_‖ even exhibited negative values (about ?5 × 10^?6°C^?1), probably due to reversible contraction of elongated tie-molecules.     

The physical and NMR characterizations of allyl‐ and crotylcelluloses

Tri‐O‐allylcellulose (degree of polymerization, DP ∼112) was prepared in ∼91% yield, and tri‐O‐crotylcellulose (DP ∼138) was prepared in ∼56% yield from microcrystalline cellulose (DP ∼172, and polydispersity index, PDI ∼1.95) using modified literature methods. Number‐average molecular weight (M_n = 31,600), weight‐average molecular weight (M_w = 191,800), and PDI = 6.07 data suggested that tri‐O‐allylcellulose may be crosslinking in air to generate branched chains. The polymer was stabilized with 100 ppm butylated hydroxy toluene (BHT). The material without BHT experienced glass transition (T_g, differential‐scanning calorimetry, DSC) between −2 and +3 °C, crosslinked beyond 100 °C, and degraded at 298.6 °C (by thermogravimetric analysis, TGA). M_n (45,100), M_w (118,200), PDI (2.62), and thermal data (T_g − 5 to +3 °C, melting point 185.8 °C, recrystallization 168.9 °C, and degradation 343.6 °C) on tri‐O‐crotylcellulose suggested that the polymer was formed with about the same polydispersity as the starting material and is heat stable. While allylcellulose generated continuous flexible yellow films by solution casting, crotylcellulose precipitated from solution as brittle white flakes. Dynamic mechanical analysis (DMA) data on allylcellulose films (T_g − 29.1 °C, Young's modulus 5.81 × 10⁸ Pa) suggest that the material is tough and flexible at room temperature. All ¹H and ¹³C resonances in the NMR spectra were identified and assigned using the following methods: Double‐quantum filter correlation spectroscopy (DQF COSY) was used to assign the network of seven protons in the anhydroglucose portion of the repeat unit. The proton assignments were verified and confirmed by total correlation spectroscopy (TOCSY). A combination of heteronuclear single‐quantum coherence (HSQC) and ¹³C spectroscopies were used to identify all bonded carbon–hydrogen pairs in the anhydroglucose portion of the repeat unit, and assign the carbon nuclei chemical shift values. Heteronuclear multiple bond correlation (HMBC) spectroscopy was used to connect the resonances of methines and methylenes at positions 2, 3, and 6 to the methylene resonances of the allyl ethers. TOCSY was used again to identify the fifteen ¹H resonances in the three pendant allyl groups. Finally, a combination of HSQC, HMBC, and ¹³C spectroscopies were used to identify each carbon in the allyl pendants at 2, 3, and 6. Because of line broadening and signal overlap, we were unable to identify the conformational arrangement about the C5 and C6 bond in tri‐O‐allyl‐ and tri‐O‐crotylcelluloses. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1889–1902, 2000     

2‐Amino‐8‐(2‐deoxy‐2‐fluoro‐β‐d‐arabinofuranosyl)imidazo[1,2‐a][1,3,5]triazin‐4(8H)‐one monohydrate,a 2′‐deoxyguanosine analogue with an altered Watson–Crick recognition site

The title compound, C₁₀H₁₂FN₅O₄·H₂O, shows an anti glycosyl orientation [χ = −123.1 (2)°]. The 2‐deoxy‐2‐fluoroarabinofuranosyl moiety exhibits a major C2′‐endo sugar puckering (S‐type, C2′‐endo–C1′‐exo, ²T₁), with P = 156.9 (2)° and τ_m = 36.8 (1)°, while in solution a predominantly N conformation of the sugar moiety is observed. The conformation around the exocyclic C4′—C5′ bond is −sc (trans, gauche), with γ = −78.3 (2)°. Both nucleoside and solvent molecules participate in the formation of a three‐dimensional hydrogen‐bonding pattern via intermolecular N—H...O and O—H...O hydrogen bonds; the N atoms of the heterocyclic moiety and the F substituent do not take part in hydrogen bonding.     

Influence of multiple processing on selected properties of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)

The effect of multiple (up to 10 times) injection molding of processed poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) (P(3,4HB)) on its phase transition temperatures, degree of crystallinity, degradation temperature, mass flow rate, mechanical properties, dynamic mechanical properties, and Charpy's impact strength is presented. The studies have shown that the multiple injection lowers the degree of crystallinity and the thermal stability of P(3,4HB). The mass flow rate values increased with increasing the injection number. It was found that the multiple injections had no substantial effect on the tensile strength up to 10 injection cycles and the tensile strength at break, tensile strain at tensile strength, and tensile strain at break up to 6 injection cycles. The maximum value of storage modulus at 30 °C and impact strength were recorded for sample after 4 cycles of injection, while the values of storage modulus at 120 °C increased with increase of the injection cycles. Copyright © 2015 John Wiley & Sons, Ltd.     

Living cationic polymerization of n‐butyl propenyl ether

Cationic polymerization of n‐butyl propenyl ether (BuPE; CH₃CH CHOBu, cis/trans = 64/36) was examined with the HCl–IBVE (isobutyl vinyl ether) adduct/ZnCl₂ initiating system at −15 ∼ −78 °C in nonpolar (hexane, toluene) and polar (dichloromethane) solvents, specifically focusing on the feasibility of its living polymerization. In contrast to alkyl vinyl ethers, the living nature of the growing species in the BuPE polymerization was sensitive to polymerization temperature and solvent. For example, living cationic polymerization of IBVE can be achieved even at 0 °C with HCl–IBVE/ZnCl₂, whereas for BuPE whose β‐methyl group may cause steric hindrance ideal living polymerization occurred only at −78 °C. Another interesting feature of this polymerization is that the polymerization rate in hexane is as large as in dichloromethane, much larger than in toluene. A new method in determining the ratio of the living growing ends to the deactivated ones was developed with a devised monomer‐addition experiments, in which IBVE that can be polymerized in a living fashion below 0 °C was added to the almost completely polymerized solution of BuPE. The amount of the deactivated chain ends became small in hexane even at −40 °C in contrast to other solvents. Thus hexane turned out an excellent solvent for living cationic polymerization of BuPE. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 229–236, 2000     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000