Crystalline Stereocomplexed Polycarbonates: Hydrogen‐Bond‐Driven Interlocked Orderly Assembly of the Opposite Enantiomers

Four novel crystalline stereocomplexed polymers are formed by mixing isotactic (R)‐ and (S)‐polycarbonates in 1:1 mass ratio. They show the enhanced thermal stability and new crystalline behavior, significantly distinct from the component enantiomer. Two stereocomplexed CO₂‐based polycarbonates from meso‐3,4‐epoxytetrahydrofuran and 4,4‐dimethyl‐3,5,8‐trioxabicyclo[5.1.0]octane have high melting temperatures of up to 300 °C, about 30 °C higher than the individual enantiomers. Isotactic (R)‐ or (S)‐poly(cyclopentene carbonate) and poly(cis‐2,3‐butene carbonate) are typical amorphous polymeric materials, however, upon mixing both enantiomers together, a strong interlocked interaction between polymer chains of opposite configuration occurs, affording the crystalline stereocomplexes with melting temperatures of about 200 °C and 180 °C, respectively. A DFT study suggests that the driving force forming the stereocomplex is the hydrogen‐bonding between carbonate units of the opposite enantiomers.     

New crystalline polymers: poly(2,5‐dialkyl‐1,4‐phenylene oxide)s

New heat‐reversibly crystalline poly‐(alkylated phenylene oxide)s are described. the oxidative polymerization of 2,5‐dimethylphenol catalyzed by (1,4,7‐triisopropyl‐1,4,7‐triazacyclononane) copper dichloride produced poly(2,5‐dimethyl‐1,4‐phenylene oxide), which showed heat‐reversible crystallinity with a high melting point at ca. 300°C, although the isomeric polymer, poly(2,6‐dimethyl‐1,4‐phenylene oxide), never recrystallizes once melted. The polymerization of 2,5‐diethylphenol and 2,5‐dipropylphenol gave the polymers consisting of 1,4‐phenylene oxide units; the latter polymer possessed heat‐reversible crystallinity, however, the former one did not.     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Synthesis and properties of new polyamides derived from 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone by direct polycondensation

A series of new polyamides containing both sulfone and oxyethylene moieties in the polymer chain was prepared by the direct polycondensation of the diamine monomer 2,2‐bis[4‐[2‐(4‐aminophenoxy)ethoxy]phenyl]sulfone (BAEPS) and various aromatic dicarboxylic acids in N‐methyl‐2‐pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with inherent viscosities of 0.30–0.60 dl/g and identified by elemental analysis, and infrared and nuclear magnetic resonance spectra. Most of the polymers were readily dissolved in polar solvents such as NMP, dimethylsulfoxide, N,N‐dimethylacetamide, N,N‐dimethylformamide and m‐cresol at room temperature. Polymers containing rigid and symmetric p‐phenylene, naphthalene and p‐biphenylene moieties revealed a crystalline nature and showed no solubility in organic solvents. These polyamides had 10% weight loss temperatures ranging between 423 and 465 °C in nitrogen atmosphere and glass transition temperatures between 170 and 305 °C. The polymers with crystallinity nature exhibited melting endotherms (T_m) below 386 °C in differential scanning calorimetry trace. Copyright © 1999 John Wiley & Sons, Ltd.     

Aromatic poly(1,3,4‐oxadiazole)s and poly(amide‐1,3,4‐oxadiazole)s containing ether sulfone linkages

Polyhydrazides and poly(amide‐hydrazide)s were prepared from two ether‐sulfone‐dicarboxylic acids, 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoic acid and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoic acid, or their diacyl chlorides with terephthalic dihydrazide, isophthalic dihydrazide, and p‐aminobenzhydrazide via a phosphorylation reaction or a low‐temperature solution polycondensation. All the hydrazide polymers were found to be amorphous according to X‐ray diffraction analysis. They were readily soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide and could afford colorless, flexible, and tough films with good mechanical strengths via solvent casting. These hydrazide polymers exhibited glass‐transition temperatures of 149–207 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the solid state at elevated temperatures. Although the oxadiazole polymers showed a significantly decreased solubility with respect to their hydrazide prepolymers, some oxadiazole polymers were still organosoluble. The thermally converted oxadiazole polymers had glass‐transition temperatures of 217–255 °C and softening temperatures of 215–268 °C and did not show significant weight loss before 400 °C in nitrogen or air. For a comparative study, related sulfonyl polymers without the ether groups were also synthesized from 4,4′‐sulfonyldibenzoic acid and the hydrazide monomers by the same synthetic routes. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2271–2286, 2001     

Molecular composites made of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Molecular composites were prepared from several types of ionically modified, poly(p‐phenylene terephthalamide) (PPTA) dispersed in a poly(4‐vinylpyridine) matrix. Optical clarity tests indicated that the component polymers of the composite were miscible, at least at low concentrations of the rodlike reinforcement. In composites containing ionic PPTA, where ionic sulfonate groups were attached as side groups either to PPTA chains or to PPTA anion chains, the glass‐transition temperature (T_g) was increased by l0 °C or more, at 5 wt % reinforcement. At concentrations of 10–15 wt % of the ionic polymer, T_g values leveled off or decreased slightly. This suggested that some aggregation of the rigid‐rod molecules occurred. In composites containing ionic PPTA, where the ionic sulfonate groups were directly attached to the phenylene rings of PPTA chains, not only was T_g shifted significantly to higher temperatures, but the rubbery plateau modulus retained high values up to temperatures of 250 °C or above. Observed effects were considered to be the result of strong ionic interactions between the ionic reinforcement polymer and the polar matrix polymer. The possible effects of the counterion on T_g and the storage modulus are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1110–1117, 2002     

Photoluminescent,liquid‐crystalline,and electrochemical properties of para‐phenylene‐based alternating conjugated copolymers

Novel liquid‐crystalline alternating conjugated copolymers [ P(P(6)CN‐alt‐Cz) and P(P(6)CN‐alt‐MeP) ] with phenylene and carbazolylene or phenylene with methyl substitution onto the main chain have been synthesized through palladium‐catalyzed Suzuki coupling reactions. The influence of the incorporation of carbazolylene and the substituted phenylene into the main chain on the thermal, mesomorphic, and luminescent properties has been investigated by Fourier transform infrared spectroscopy, thermogravimetry, differential scanning calorimetry, polarized optical microscopy, ultraviolet–visible spectroscopy, photoluminescence (PL), and cyclic voltammetry. These polymers show highly thermal stability, losing little of their weights when heated to 360 °C. The conjugated copolymers exhibit liquid crystallinity at elevated temperature. The existence of the chromophoric terphenyl core endows the copolymers with high PL and the polymer P(P(6)CN‐alt‐Cz containing carbazolylene unit can emit more pure blue light. All the copolymer films with low band gaps about 2.3–2.4 eV undergo reversible oxidation and reduction processes, significantly lower than the band gap of poly(p‐phenylene). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 434–442, 2010     

Poly(arylene sulfides) with pendant cyano groups as high-temperature laminating resins. II

Poly(phenylene sulfides) containing various amounts of pendant cyano groups were synthesized from m-benzenedithiol and the corresponding amounts of p-dibromobenzene and 3,5-dichlorobenzonitrile. The polymers prepared by the use of 10, 15, 20, and 25% of the nitrile-containing dichloro compound were slightly off-white with melting ranges below 100°C and had inherent viscosities of about 0.15 dl/g in hexamethylphosphoric triamide at 30°C. The polymers prepared from m-benzenedithiol and the stoichiometric amounts of 2,4-dichlorobenzonitrile or 3,5-dichlorobenzonitrile looked similar to those described above, yet they possessed much higher melting ranges. The poly(phenylene sulfide) prepared by the use of 2,4-dichlorobenzonitrile had an inherent viscosity of 0.06 dl/g while the polymer prepared from the 3,5-dichloro isomer had an inherent viscosity of 0.38 dl/g. All the polymers listed above were crosslinked by heating alone or in the presence of anthracene-9,10-bisnitrile oxide to give black resinous polymers that were insoluble in hexamethylphosphoric triamide in which the original polymers dissolved quite readily.     

New poly(amide-imide)s syntheses. VII. Preparation and properties of poly(amide-imide)s derived from 1,5-bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

New bis(phenoxy)naphthalene-containing poly(amide-imide)s having an inherent viscosity in the range of 0.62–1.09 dL/g were prepared by the direct polycondensation of 1,5-bis(4-trimellitimidophenoxy) naphthalene ( I ) and various aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The diimide-diacid (I) was prepared by the condensation of 1,5-bis(4-aminophenoxy) naphthalene and trimellitic anhydride. Most of the polymers were soluble in aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc), and afforded transparent, flexible and tough films upon casting from DMAc solutions. Measurements of wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or oxyphenylene groups were characterized as crystalline polymers. Tensile strength and initial moduli of the polymer films ranged from 61–86 MPa and 1.83–2.21 GPa, respectively. Glass transition temperatures of the polymers were in the range of 231–340°C. The melting points of the crystalline polymers ranged from 375–430°C. The 10% weight loss temperatures were above 512°C in nitrogen and 481°C in air. © 1993 John Wiley & Sons, Inc.     

Higher aliphatic polyaldehydes. II. Polymer structure and polymer stability of poly(n-heptaldehyde)

Poly(n-heptaldehyde) has been prepared by anionic and cationic polymerization at ?60°C in methyl cyclohexane. The anionic polymer is more crystalline and of a higher degree of isotactic structure than the somewhat rubbery but still crystalline cationic polymer. The polymers have been acetate-endcapped to improve their thermal stability. Cationic polymer, when endcapped and purified, begins to degrade above room temperature; even crystalline anionic polymer degrades at a reasonable rate at 100°C. The crystallinity of poly(n-heptaldehyde) is caused by crystallization of the acetalic main chain as well as the side chain. Two regions of melting have been recognized by DSC analysis and by microscopic observations. The low melting region between 80 and 100°C has been identified as the melting of the paraffinic side chains of poly(n-heptaldehyde). It consists of three clearly definable endotherms at 78, 87, and 101°C.     

New high temperature polymers. I. Wholly aromatic ordered copolyamides

Wholly aromatic ordered copolyamides of unusually high thermal stability were prepared by the condensation of aromatic diacid chlorides with symmetrical diamines containing preformed aromatic amide units in an ordered arrangement. The preservation of order in the condensation step was assured by using interfacial or solution polymerization techniques at temperatures below 50°C. Each polymer contains units derived from aminobenzoic acids, arylene diamines, and arylene diacids. By use of para- and meta- phenylene units, eight different polymers are possible; all were prepared. Differential thermal analyses and thermogravimetric analyses showed these polymers to have melting points or decomposition temperatures in a range from 410°C. for the all-meta polymer to 555°C. for the all-para one. Substitution of the internal N-hydrogens of the diamines with methyl groups or phenyl groups leads to additional ordered copolymers. Several were prepared, but their melting points were much lower than those of the parent polymers limiting their usefulness in high temperature applications. Tough pliable films were prepared from all eight unsubstituted polymers, and crystalline fibers with tenacities of ca. 6 g./den. were prepared from three of the polymers. The properties of the fibers were retained to a high degree even when determined at temperatures up to 400°C. Fibers aged at 300°C. for extended periods of time showed remarkable retention of fiber properties.     

Synthesis and properties of new soluble N-phenyl–substituted aromatic-aliphatic and all aromatic polyamides derived from 4,4′-dianilinobiphenyl

New N-phenylated aromatic-aliphatic and all aromatic polyamides were prepared by the high-temperature solution polycondensation of 4,4′-dianilinobiphenyl with both aliphatic (methylene chain lengths of 6–11) and aromatic dicarboxylic acid chlorides. All of the aromatic-aliphatic polyamides and the wholly aromatic polyamides exhibited an amorphous nature and good solubility in amide-type and chlorinated hydrocarbon solvents, except for those aromatic polyamides containing p-oriented phenylene or biphenylylene linkages in the backbone; the latter were crystalline and insoluble in organic solvents except m-cresol. The N-phenylated aromatic-aliphatic polyamides and aromatic polyamides had glass transition temperatures in the range of 79–116°C and 207–255°C, respectively, and all the polymers were thermally stable with decomposition temperatures above 400°C in air. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2193–2200, 1998     

Palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodide,aromatic bis(boronic acid propanediol ester), and norbornadiene: A new route for poly(p‐phenylene vinylene)

A novel synthetic method for soluble precursor polymers of poly(p‐phenylene vinylene) (PPV) derivatives by the palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodides, aromatic bis(boronic acid) derivatives, and norbornadiene is described. For example, the polymerization of 1,4‐diiodo‐2,5‐dioctyloxybenzene, benzene‐1,4‐bis(boronic acid propanediol ester), and norbornadiene at 100 °C for 3 days provided a polymer consisting of the three monomer units in a 97% yield (number‐average molecular weight = 3100, weight‐average molecular weight/number‐average molecular weight = 1.37). A derivative of PPV was produced smoothly by the retro Diels–Alder reaction of the polymer both in a dodecyloxybenzene solution and in a film at 200 °C in vacuo. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3403–3410, 2005     

Synthesis and optical properties of novel blue‐light‐emitting poly(p‐phenylene vinylene) derivatives with pendant oxadiazole or cyano groups

Two novel poly(p‐phenylene vinylene) polymers, which carried side substituents with cyano groups or 1,3,4‐oxadiazole, were synthesized by Heck coupling. They consisted of alternating conjugated segments and nonconjugated aliphatic spacers. The polymers had moderate molecular weights, were amorphous, and dissolved readily in tetrahydrofuran and halogenated organic solvents. They were stable up to approximately 340 °C in N₂ and 290 °C in air, and the anaerobic char yield was around 60% at 800 °C. The polymer with cyano side groups emitted blue light in solutions and thin films with identical photoluminescence (PL) maximum at 450 nm; this supported the idea that chain interactions were hindered even in the solid state. The PL maximum of this polymer in thin films was blueshifted upon annealing at 120 °C, indicating a thermochromic effect as a result of conformational changes in the polymer backbone. The polymer containing side substituents with oxadiazole rings emitted blue light in solutions with a PL maximum at 474 nm and blue‐greenish light in thin films with a PL maximum at 511 nm. The PL quantum yields of the polymers in tetrahydrofuran were 0.13–0.24. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1768–1778, 2004     

Synthesis and Characterization of Novel Poly(Arylene Ether)s from 1,3‐bis(4‐Hydroxyphenyl) Benzene

Abstract

Several poly(aryl ether)s have been prepared by the condensation of 1,3‐bis(4‐hydroxy phenyl) benzene with different trifluoromethyl activated bis‐fluoro compounds. IR, ¹H and ¹³C NMR, and elemental analyses have established the resulting polymer structures. The properties of the polymers have been evaluated by DSC, TGA, dynamic mechanical analysis (DMA) and stress–strain analysis. The polymers 1a and 1c showed semi‐crystalline behavior as evident by sharp crystalline melting peaks at 299°C and 330°C along with glass transitions at 202°C and 216°C, respectively. The polymers showed very good thermal stability in air, high modulus, and high tensile strength with low elongation at break.     

Pressure‐induced amorphization and disordering on cooling in semi‐crystalline polymers: calorimetric evidence for inverse melting in one component system

We report some unusual phase behaviour, of general implication for condensed matter, on the polymer poly‐4‐methyl pentene‐1 (P4MP1) induced by changes in pressure (P) and temperature (T), as observed by in‐situ X‐ray diffraction and high pressure DSC. Upon increasing pressure beyond a threshold value, the polymer, crystalline at ambient conditions, looses its crystalline order isothermally. The process is reversible. This behaviour is observed in two widely separated temperature regions, one below the glass transition temperature (< 50°C) and one close to the melting temperature (250°C), thus showing solid state amorphization and inversion in the melting temperature with increasing pressure. This further suggests inverse melting, i.e. re‐entrant of the two widely separated liquid and amorphous phases along the T‐axis at fixed P. This is confirmed experimentally as disordering in the crystalline structure on cooling. The inverse melting in P4MP1 raises the possibility of exothermic melting and endothermic crystallization as anticipated by Tammann (1903), see reference 1. The anticipated exothermic melting and endothermic crystallization is confirmed experimentally in the one component system P4MP1. We are observing similar features in a range of polymers.     

Origin of double melting behavior of poly(p‐phenylene succinate)

The origin of double melting behavior of poly(p‐phenylene succinate) (PPSc) was investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction. As‐polymerized PPSc showed two melting peaks: the low melting (LM) and high melting (HM) peaks at 286 and 311 °C, respectively. When PPSc was annealed at 270 °C, the LM peak constantly shifted toward higher temperatures and grew in its area with annealing time, and eventually merged into the HM peak located at 308 °C. X‐ray diffractograms of PPSc annealed at 270 °C became sharper with increasing the annealing time while the peak positions did not change. The X‐ray diffractograms obtained from the LM and the HM peak exhibited the same diffraction peaks. It was concluded from these results that the double melting behavior of PPSc is due to the distribution of crystals having the same crystal form but differing in size and perfection. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1868–1871, 2000     

Synthesis and properties of nitrogen‐linked poly(2,7‐carbazole)s as hole‐transport material for organic light emitting diodes

A novel class of carbazole polymers, nitrogen‐linked poly(2,7‐carbazole)s, was synthesized by polycondensation between two bifunctional monomers using the palladium‐catalyzed amination reaction. The polymers were characterized by ¹H NMR, Infrared, Gel permeation chromatography, and MALDI‐TOF MS and it was revealed that the combination of the monomer structures is important for producing high molecular weight polymers. Thermal analysis indicated a good thermal stability with high glass transition temperatures, e.g., 138 °C for the higher molecular weight polymer P2 . To pursue the application possibilities of these polymers, their optical properties and energy levels were investigated by UV‐Vis absorption and fluorescence spectra as well as their electrochemical characteristics. Although the blue light emission was indeed observed for all polymers in solution, the quantum yields were very low and the solid films were not fluorescent. On the other hand, the HOMO levels of the polymers estimated from the onset potentials for the first oxidation in the solid thin films were relatively high in the range of ?5.12 to ?5.20 eV. Therefore, light emitting diodes employing these polymers as a hole‐transport layer and iridium(III) complex as a triplet emitter were fabricated. The device of the nitrogen‐linked poly(2,7‐carbazole) P3 with p,p′‐biphenyl spacer, which has a higher HOMO level and a higher molecular weight, showed a much better performance than the device of P2 with m‐phenylene spacer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3880–3891, 2009     

Poly(p‐phenylene methylene)‐based block copolymers by mechanistic transformation

The synthesis of poly(p‐phenylene methylene) (PPM)‐based block copolymers such as poly(p‐phenylene methylene)‐b‐poly(ε‐caprolactone) and poly(p‐phenylene methylene)‐b‐polytetrahydrofuran by mechanistic transformation was described. First, precursor PPM was synthesized by acid‐catalyzed polymerization of tribenzylborate at 16 °C. Then, this polymer was used as macroinitiators in either ring‐opening polymerization of ε‐caprolactone or cationic ring‐opening polymerization of tetrahydrofuran to yield respective block copolymers. The structures of the prepolymer and block copolymers were characterized by GPC and ¹H NMR investigations. The composition of block copolymers as determined by ¹H NMR and TGA analysis was found to be in very good agreement. The thermal behavior and surface morphology of the copolymers were also investigated, respectively, by differential scanning calorimetry and atomic force microscopy measurements, and the contribution of the major soft segment has been observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thermal behavior of poly-p-xylylene-m-carborane

Thermal analysis, infrared spectroscopy, and gel-permeation chromatography studies were undertaken to determine the behavior of poly(p-xylylene-m-carborane) at elevated temperature. Results show that the polymer softened at about 200°C, probably because of polymorphism. Chlorine atoms from chain ends also ruptured at this temperature. This initiated subsequent hydrogen abstraction and thermal oxidation reactions that resulted in the decomposition of the polymer. The process of degradation closely parallels the thermal oxidation of polybenzyl and other polymers with readily activated methylene groups. The volatile products that formed at 300 and 400°C were produced because of the cleavage of methylene groups and their oxidation products. Larger polymer segments containing phenylene and m-carborane groups were evolved at higher temperatures. Some crosslinking occurred when the polymer was heated in air at temperatures above 200°C. The degree of polydispersity of the polymer fraction that remained soluble in organic solvents increased with corresponding increase of temperature.