Cationic polymerization of glycidyl phenyl ether initiated by various arylsulfonium salts as new thermal latent cationic initiators

The cationic initiation activity of derivatives of S-methylsulfonium salts has been evaluated in the cationic polymerization of glycidyl phenyl ether ( 1 ). These initiators are soluble in 1 and capable of initiating the cationic polymerization of 1 on heating, except for methyltetrahydrothiophenium tetrafluoroborate ( 6 ) (r.t. −160°C). Among them, methyldiphenylsulfonium tetrafluoroborate ( 4 ) shows moderate thermal latency, that is the polymerization of 1 occurs efficiently at 160°C but not below 80°C.     

Application of novel polymers with S‐alkylsulfonium salt moieties as alkylating agents and thermal latent cationic initiators

Sulfonium‐containing polymers prepared from dibenzothiophene and diphenyl sulfide were applied as both alkylating agents and latent initiators for the cationic polymerization of glycidyl phenyl ether. The alkylation of acetonitrile proceeded smoothly with poly(S‐n‐octyl‐2‐vinyldibenzothiophenium tetrafluoroborate) ( 4 ; 64 mol % octyldibenzothiophenium tetrafluoroborate unit) to give N‐(n‐octyl)acetamide in an excellent yield on the basis of the starting octyldibenzothiophenium tetrafluoroborate unit in 4 . The cationic polymerization of glycidyl phenyl ether was also carried out in the presence of poly(S‐methyl‐2‐vinyldibenzothiophenium tetrafluoroborate) or poly(S‐n‐octyl‐4‐vinyldiphenylsulfonium tetrafluoroborate) to confirm their moderate thermal latent activity. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3928–3933, 2001     

Cationic polymerization behavior of isobutyl vinyl ether with arenesulfonates as non‐salt‐type latent thermal initiators

Substituted and unsubstituted benzenesulfonic acid cyclohexyl esters (1–7) were synthesized, and their possibility as latent thermal initiators in the cationic polymerization of isobutyl vinyl ether (IBVE) was examined to develop novel non‐salt type latent cationic initiators. Thermal decomposition of cyclohexyl p‐nitrobenzenesulfonate (2) in C₆D₆ at 80°C proceeded to exclusively afford cyclohexene as well as p‐nitrobenzenesulfonic acid. Cationic polymerization of IBVE with 1 mol % of an arenesulfonate (1–6) in bulk was carried out at 40–100°C for 12 h. No polymerization took place below 50°C, while the consumption of IBVE depending on both the polymerization temperature and the structure of the arenesulfonates was observed above 60°C. The obtained polyIBVEs showed bimodal GPC curves in several cases, revealing the intervention of two independent propagation species in the polymerization. The cationic polymerization of IBVE with cyclohexyl 2,4,6‐triisopropylbenzenesulfonate (7) at 80°C confirmed the acceleration effect of bulkiness on the polymerization rate. It was concluded that the polymerization was largely dependent on both electronic and steric factors of the aryl groups of the initiators which were directly related to the stability of the sulfonate anions. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 293–301, 1999     

Curing behavior of epoxy resin initiated by S‐alkylsulfonium salts of aromatic sulfides as thermal latent cationic initiators

The curing behavior of bisphenol‐A‐type epoxide oligomers (Ep) was evaluated by differential scanning calorimetry in the presence of S‐alkylsulfonium salts of dibenzothiophene, phenoxathiin, thianthrene, thioanisole, and tetrahydrothiophene as thermal latent initiators. These initiators dissolved homogeneously in Ep, except for 2,8‐dimethoxy‐5‐methyldibenzothiophenium tetrafluoroborate, and the curing reaction of the resulting mixtures occurred on heating, except for S‐methyltetrahydrothiophenium tetrafluoroborate. The initiation activity of these salts was controlled by the character of the substituents on the benzene ring, the leaving sulfide group, and the S‐alkyl group. Presumably, the electron density on the sulfide moieties and the stability of the carbocation released from the sulfonium salts affected the initiating temperature. A good correlation was obtained between the initiating temperature and the electron density of the sulfur atom of the corresponding sulfides, estimated from ab initio molecular orbital calculations in which the initiating temperature became higher as the electron density of the sulfur atom increased. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 868–871, 2001     

Polymerization of o‐quinodimethanes. V. Ionic polymerization of o‐quinodimethanes generated by thermal isomerization of corresponding benzocyclobutenes

The ionic polymerization of substituted o‐quinodimethanes via thermal isomerization of benzocyclobutenes is described. In the cationic polymerizations of 1‐methoxy‐o‐quinodimethane in the presence of various cationic initiators at 110 °C for 12 h, chain transfer reactions also considerably underwent besides the polymerization. Meanwhile, cationic polymerizations of 1‐trimethylsilyloxy‐o‐quinodimethane under the same conditions gave good yields of the corresponding polymer. Anionic polymerizations of 1‐cyano‐o‐quinodimethane in the presence of anionic initiators such as n‐BuLi or t‐BuOK were performed at various temperatures for 12 h. Good yields of hexane‐insoluble polymer, which was produced by anionic polymerization of corresponding o‐quinodimethane as an intermediate, were obtained above 120 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 844–850, 2008     

Novel N‐methylbenzothiazolium salts as hardeners for epoxy and acrylate monomers

Novel N‐methylbenzothiazolium salts [N‐methyl‐2‐benzylthiobenzothiazolium, N‐methyl‐2‐(4‐nitrobenzylthio)benzothiazolium, N‐methyl‐2‐(1‐ethoxycarbonylethylthio)benzothiazolium, and N‐methyl‐2‐methylthiobenzothiazolium hexafluoroantimonates] were synthesized by the reaction of the corresponding 2‐substituted benzothiazole with dimethylsulfate, followed by anion exchange with KSbF₆. These benzothiazolium salts cationically polymerized an epoxy monomer by photoirradiation. They also polymerized an acrylate monomer via a photoradical process. The use of aromatic compounds such as 2‐ethyl‐9,10‐dimethoxyanthracene as photosensitizers was effective in enhancing the polymerization. These benzothiazolium salts also served as thermal cationic initiators. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3828–3837, 2003     

Photoinduced and thermally induced cationic polymerizations using S,S‐dialkyl‐S‐(3,5‐dimethylhydroxyphenyl)sulfonium salts

A study of the photoinitiated and thermally initiated cationic polymerizations of several monomer systems with S,S‐dialkyl‐S‐(3,5‐dimethylhydroxyphenyl)sulfonium salt (HPS) photoinitiators bearing different lengths of alkyl chains on the positively charged sulfur atom has been conducted. HPS photoinitiators are capable of photoinitiating the cationic polymerization of a wide variety of epoxy and vinyl ether monomers directly on irradiation with short‐wavelength UV light. Aryl ketone photosensitizers are effective in extending the spectral response of these photoinitiators into the long‐wavelength UV region. Kinetic studies with real‐time infrared spectroscopy show that HPS photoinitiators exhibit good efficiency in the polymerization of epoxide and vinyl ether monomers. Comparative studies also demonstrate that S,S‐dimethyl‐S‐(3,5‐dimethyl‐2‐hydroxyphenyl)sulfonium salts are more active photoinitiators than their isomeric S,S‐dimethyl‐S‐(3,5‐dimethyl‐4‐hydroxyphenyl)sulfonium salt counterparts. Both types of HPS photoinitiators display reversible photolysis as a result of facile termination reactions that take place between the growing chains ends with the photogenerated sulfur ylides. Preliminary studies have shown that HPS photoinitiators can also be employed as thermal initiators for the cationic ring‐opening polymerization of epoxides at moderate temperatures. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2570–2587, 2003     

Photosensitization of carbazole derivatives in cationic polymerization with a novel sensitivity to near‐UV light

Photosensitizers based on the carbazole structure were designed and developed for cationic polymerization. Along with triarylsulfonium and diaryliodonium salts, the carbazole derivatives showed a high photosensitization effect in the cationic photopolymerization of epoxides. The photophysical properties of the carbazole derivatives were studied in terms of electronic absorption, fluorescence, and phosphorescence spectrometry. Moreover, a unique photosensitization mechanism of the carbazole derivatives was discussed after studies of the fluorescence quenching, redox behavior, and kinetics of the photopolymerization by time‐resolved fluorescence spectrometry, cyclic voltammetry, and photo differential scanning calorimetry, respectively. The results confirmed the redox photosensitization of the carbazole derivatives in cationic polymerization. The photosensitization of the carbazole and its ring or N‐alkylated derivatives occurred predominantly in singlet excited states at the rate of the diffusion limit, whereas the carbazole derivatives with carbonyl substituents sensitized onium salts via triplet excited states on the basis of the Rehm–Weller equation in the photoinduced electron‐transfer process. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 90–100, 2000     

Atom transfer radical polymerization of styrenic ionic liquid monomers and carbon dioxide absorption of the polymerized ionic liquids

Polymeric forms of ionic liquids have many potential applications because of their high thermal stability and ionic nature. Two ionic liquid monomers, 1‐(4‐vinylbenzyl)‐3‐butyl imidazolium tetrafluoroborate (VBIT) and 1‐(4‐vinylbenzyl)‐3‐ butyl imidazolium hexafluorophosphate (VBIH), were synthesized through the quaternization of N‐butylimidazole with 4‐vinylbenzylchloride and a subsequent anion‐ exchange reaction with sodium tetrafluoroborate or potassium hexafluorophosphate. Copper‐mediated atom transfer radical polymerization was used to polymerize VBIT and VBIH. The effects of various initiator/catalyst systems, monomer concentrations, solvent polarities, and reaction temperatures on the polymerization were examined. The polymerization was well controlled and exhibited living characteristics when CuBr/1,1,4,7,10,10‐hexamethyltriethylenetetramine or CuBr/2,2′‐bipyridine was used as the catalyst and ethyl 2‐bromoisobutyrate was used as the initiator. Characterizations by thermogravimetric analysis, differential scanning calorimetry, and X‐ray diffraction showed that the resulting VBIT polymer, poly[1‐(4‐vinylbenzyl)‐3‐butyl imidazolium tetrafluoroborate] (PVBIT), was amorphous and had excellent thermal stability, with a glass‐transition temperature of 84 °C. The polymerized ionic liquids could absorb CO₂ as ionic liquids: PVBIT absorbed 0.30% (w/w) CO₂ at room temperature and 0.78 atm. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1432–1443, 2005     

Living cationic polymerization of n‐butyl propenyl ether

Cationic polymerization of n‐butyl propenyl ether (BuPE; CH₃CH CHOBu, cis/trans = 64/36) was examined with the HCl–IBVE (isobutyl vinyl ether) adduct/ZnCl₂ initiating system at −15 ∼ −78 °C in nonpolar (hexane, toluene) and polar (dichloromethane) solvents, specifically focusing on the feasibility of its living polymerization. In contrast to alkyl vinyl ethers, the living nature of the growing species in the BuPE polymerization was sensitive to polymerization temperature and solvent. For example, living cationic polymerization of IBVE can be achieved even at 0 °C with HCl–IBVE/ZnCl₂, whereas for BuPE whose β‐methyl group may cause steric hindrance ideal living polymerization occurred only at −78 °C. Another interesting feature of this polymerization is that the polymerization rate in hexane is as large as in dichloromethane, much larger than in toluene. A new method in determining the ratio of the living growing ends to the deactivated ones was developed with a devised monomer‐addition experiments, in which IBVE that can be polymerized in a living fashion below 0 °C was added to the almost completely polymerized solution of BuPE. The amount of the deactivated chain ends became small in hexane even at −40 °C in contrast to other solvents. Thus hexane turned out an excellent solvent for living cationic polymerization of BuPE. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 229–236, 2000     

Living cationic polymerization of vinylnaphthalene derivatives

The living cationic polymerization of 6‐tert‐butoxy‐2‐vinylnaphthalene (tBOVN), a vinylnaphthalene derivative with an electron‐donating group, was achieved with a TiCl₄/SnCl₄ combined initiating system in the presence of ethyl acetate as an added base at –30 °C. The absence of side reactions at low temperature was confirmed by ¹H NMR analysis of the resulting polymer. In contrast to this controlled reaction at –30 °C, reactions performed at higher temperature, such as 0 °C, frequently involved unwanted intramolecular or intermolecular Friedel–Crafts reactions of naphthalene rings due to the high electron density of these rings. The cationic polymerization of 6‐acetoxy‐2‐vinylnaphthalene, a derivative with an acetoxy group, was also controlled under similar conditions, but chain transfer reactions were not completely suppressed during the polymerization of 2‐vinylnaphthalene. The glass transition temperature (T_g) of the obtained poly(tBOVN) was 157 °C, a value higher by 94 °C than that of the corresponding styrene derivative. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4828–4834     

Living cationic polymerization of dihydrofuran and its derivatives

Cationic polymerization of 2,3‐dihydrofuran (DHF) and its derivatives was examined using base‐stabilized initiating systems with various Lewis acids. Living cationic polymerization of DHF was achieved using Et_1.5AlCl_1.5 in toluene in the presence of THF at 0 °C, whereas it has been reported that only less controlled reactions occurred at 0 °C. Monomer‐addition experiments of DHF and the block copolymerization with isobutyl vinyl ether demonstrated the livingness of the DHF polymerization: the number–average molecular weight of the polymers shifted higher with low polydispersity as the polymerization proceeded after the monomer addition. Furthermore, this base‐stabilized cationic polymerization system allowed living polymerization of ethyl 1‐propenyl ether and 4,5‐dihydro‐2‐methylfuran at ?30 and ?78 °C, respectively. In the polymerization of 2,3‐benzofuran, the long‐lived growing species were produced at ?78 °C. The obtained polymers have higher glass transition temperatures compared to poly(acyclic alkyl vinyl ether)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4495–4504, 2008     

Palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodide,aromatic bis(boronic acid propanediol ester), and norbornadiene: A new route for poly(p‐phenylene vinylene)

A novel synthetic method for soluble precursor polymers of poly(p‐phenylene vinylene) (PPV) derivatives by the palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodides, aromatic bis(boronic acid) derivatives, and norbornadiene is described. For example, the polymerization of 1,4‐diiodo‐2,5‐dioctyloxybenzene, benzene‐1,4‐bis(boronic acid propanediol ester), and norbornadiene at 100 °C for 3 days provided a polymer consisting of the three monomer units in a 97% yield (number‐average molecular weight = 3100, weight‐average molecular weight/number‐average molecular weight = 1.37). A derivative of PPV was produced smoothly by the retro Diels–Alder reaction of the polymer both in a dodecyloxybenzene solution and in a film at 200 °C in vacuo. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3403–3410, 2005     

Thermal decomposition of amide and imide derivatives of maleated polyethylene

The thermal decomposition behavior of six derivatives of maleated polyethylene was investigated by high‐resolution pyrolysis gas chromatography–mass spectrometry. The results revealed that substituents attached to maleated polyethylene as amides formed from secondary amines were significantly less stable than imides formed from primary amines. Morpholine amide and N‐methylaniline amide derivatives of maleated polyethylene underwent significant decomposition at 160 °C and substantial decomposition at 200 °C. In contrast, the imide derivatives of maleated polyethylene were stable for long periods of time at elevated temperatures. Following 2 min of heating, the first traces of decomposition were detected at 200 °C for the 2‐aminoanthrancene imide derivative, at 255 °C for the 2‐phenethylamine imide, and at 280 °C for the 9‐aminomethylphenanthrene imide. With the exception of the 9‐aminomethylphenanthrene imide, all other derivatives decomposed to form the corresponding amine as the single most significant volatile product. The most likely explanation for this result is that the polymer contained small amounts of succinamic acid that did not close to form the imide. We concluded that the imide was stable even to 315 °C and that the amine was lost from β‐carboxyamide groups present in the sample. In the 9‐aminomethylphenanthrene imide derivative, we observed no loss of amine. Instead, we observed an alternative fragmentation process yielding 9‐methyl phenanthrene. The dependence of the thermal stability of these various derivatives of maleated polyethylene has important implications for the design of reactive‐blending strategies for polyolefins with other functional polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 730–740, 2000     

Novel pyridinium salts as cationic thermal and photoinitiators and their photosensitization properties

Novel pyridinium salts [N‐(α‐phenylbenzyl)‐, N‐(1‐naphthylmethyl)‐, or N‐cinnamyl p‐ or o‐cyanopyridinium hexafluoroantimonates] were synthesized by the reaction of p‐ or o‐cyanopyridine and the corresponding bromides followed by anion exchange with KSbF₆. These pyridinium salts polymerized epoxy monomers at lower temperatures than previously reported for N‐benzyl‐2‐cyanopyridinium hexafluoroantimonate. The o‐substituted pyridinium salts showed higher activity than the p‐substituted ones, and the crosslinked epoxy polymers cured with these initiators showed higher glass‐transition temperatures. These pyridinium salts photoinitiated radical polymerization as well as cationic polymerization. The photopolymerization was accelerated by the addition of aromatic ketones as photosensitizers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1037–1046, 2002     

Cationic polymerizations of 2‐alkyloxazolines catalyzed by bismuth salts

Acidic bismuth salts, such as BiCl₃, BiBr₃, BiJ₃, and Bi‐triflate catalyzed the ring‐opening polymerization of 2‐methoxazoline (MOZ) in bulk at 100 °C, whereas less acidic salts such as Bi₂O₃ or Bi(III)acetate did not. Bi‐triflate‐catalyzed polymerizations of 2‐ethyloxazoline (EtOZ) were performed with variation of the monomer–catalyst ratio (M/C). It was found that the molecular weights were independent of the M/C ratio. The formation of cationic chain ends and the absence of cycles was proven by reactions of virgin polymerization products with N,N‐dimethyl‐4‐aminopyridine or triphenylphosphine. The resulting polymers having modified cationic chain ends were characterized by ¹H NMR spectroscopy and MALDI‐TOF mass spectrometry. The polymerization mechanism including chain‐transfer reactions is discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4777–4784, 2008     

Sequential synthesis of multiblock copolymers by atom transfer radical and cationic polymerization

ABCBA‐type pentablock copolymers of methyl methacrylate (MMA), styrene (S), and isobutylene (IB) were prepared by a three‐step synthesis, which included atom transfer radical polymerization (ATRP) and cationic polymerization: (1) poly(methyl methacrylate) (PMMA) with terminal chlorine atoms was prepared by ATRP initiated with an aromatic difunctional initiator bearing two trichloromethyl groups under CuCl/2,2′‐bipyridine catalysis; (2) PMMA with the same catalyst was used for ATRP of styrene, which produced a poly(S‐b‐MMA‐b‐S) triblock copolymer; and (3) IB was polymerized cationically in the presence of the aforementioned triblock copolymer and BCl₃, and this produced a poly(IB‐b‐S‐b‐MMA‐b‐S‐b‐IB) pentablock copolymer. The reaction temperature, varied from ?78 to ?25 °C, significantly affected the IB content in the product; the highest was obtained at ?25 °C. The formation of a pentablock copolymer with a narrow molecular weight distribution provided direct evidence of the presence of active chlorine at the ends of the poly(S‐b‐MMA‐b‐S) triblock copolymer, capable of the initiation of the cationic polymerization of IB in the presence of BCl₃. A differential scanning calorimetry trace of the pentablock copolymer (20.1 mol % IB) showed the glass‐transition temperatures of three segregated domains, that is, polyisobutylene (?87.4 °C), polystyrene (95.6 °C), and PMMA (103.7 °C) blocks. One glass‐transition temperature (104.5 °C) was observed for the aforementioned triblock copolymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6098–6108, 2004     

Thermal radical initiator derivatives based on O‐imino‐isourea: Synthesis,polymerization, and characterization

The new thermal radical initiators (TRIs) with linear and cyclic type groups based on derivatives of O‐imino‐isourea have been designed and synthesized. The radical polymerization property of the synthesized TRI derivatives as a radical initiator in n‐butyl acrylate was monitored by differential scanning calorimetry analysis. TRI derivatives with linear type groups, such as 3‐PenDCC, 3‐HexDCC, and 4‐HepDCC, showed peak temperatures (T_peak) of 80–84 °C, whereas those with cyclic type groups, such as C‐PenDCC, C‐HexDCC, and C‐HepDCC, exhibited a wide T_peak distribution in the 74–87 °C range. The polymerization efficiency using new TRIs in n‐butyl acrylate was elaborately identified from the molecular weights and conversion obtained using gel permeation chromatography analysis and NMR spectroscopy. To consider their possible application to automotive clearcoats, the real‐time evolution of the rheological properties of clearcoat resins during the crosslinking process with newly synthesized TRI derivatives was measured, confirming the different crosslinking kinetics of TRI derivatives in real thermal curing process. The results were found to be well correlated with data from the radical polymerization experiments of TRIs. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3593–3600.     

Block and star block copolymers by mechanism transformation. I. Synthesis of PTHF‐PSt‐PTHF by the transformation of ATRP into CROP

Polystyrene (PSt) with end‐terminal bromine (Br‐PSt‐Br) was synthesized by the atom transfer radical polymerization of styrene with the difunctional initiator 1,2‐bis(2′‐bromobutyryloxy)ethane in combination with CuBr and bipyridine. The Br‐PSt‐Br reacted with silver perchlorate at −78 °C, and the resulting macromolecular initiator was used to initiate the polymerization of tetrahydrofuran. Triblock poly(tetrahydrofuran)‐polystyrene‐poly(tetrahydrofuran) (PTHF‐PSt‐PTHF) diol was obtained after propagation at −15 °C. The conversion of the polymerization was measured by gas chromatography. The structures of the triblock copolymer PTHF‐PSt‐PTHF diol were characterized by ¹H NMR and gel permeation chromatography. The mechanism of cationic ring‐opening polymerization is discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 337–344, 2000     

Reverse atom transfer radical polymerization of methyl methacrylate initiated by p‐chlorobenzenediazonium tetrafluoroborate

The controlled polymerization of methyl methacrylate (MMA) in bulk was initiated with p‐chlorobenzenediazonium tetrafluoroborate ( 1 ) and Cu(II) or Cu(I)/Cu(II)/N,N,N′,N″,N″‐pentamethyldietylene triamine (PMDETA) complex system at various temperatures (20, 60, and 90 °C). The proposed polymerization mechanism is based on the Meerwein‐type arylation reaction followed by a reverse atom transfer radical polymerization. In this mechanism, aryl radicals formed by the reaction with 1 and Cu(I) and/or PMDETA initiated the polymerization of MMA. The polymerization is controlled up to a molecular weight of 46,000 at 90 °C. Chain extension was carried out to confirm the controlled manner of the polymerization system. In all polymerization systems, the polydispersity index and initiator efficiency ranged from 1.10–1.57 to 0.10–0.21, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2019–2025, 2003