A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

没食子酸在电活化玻碳电极上的电化学行为及测定

采用循环伏安法和线性扫描伏安法对没食子酸在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在pH7.0的磷酸盐缓冲溶液中,用恒电位法在1.7 V电位阳极氧化400 s。然后在pH3.0的柠檬酸盐缓冲溶液中,没食子酸在0.479 V和0.442 V处有一良好的氧化还原峰,在0.02～0.40 V s-1范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的准可逆过程。线性循环伏安法的氧化峰电流与没食子酸浓度1×10-6～1×10-4mol L-1范围内呈良好的线性关系(r=0.980 6),检出限为7.6×10-7mol L-1(S/N=3)。该方法操作简便,重现性较好,并应用此法分析了健民咽喉片剂中的没食子酸的含量。     

Electrochemistry and voltammetric determination of tannic acid on a single-wall carbon nanotube-coated glassy carbon electrode

The voltammetric behavior of tannic acid (TA) on a single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode has been investigated by cyclic voltammetry. TA can generate a well-defined anodic peak on the modified electrode at around 0.42 V (vs. SCE) in 0.10 M phosphate buffer solutions (pH = 4.0). The electrochemical reaction involves 1e transfer, accompanied by one proton. The electrode process is controlled by adsorption. The parameters affecting the response of TA, such as solution pH, accumulation time and accumulation potential are optimized for the determination of TA. Under the optimum conditions, the peak current changes linearly with the TA concentration in the range of 5.0 × 10⁻⁸–1.0 × 10⁻⁶ M. The lowest detectable concentration of TA is 8.0 × 10⁻⁹ M after 180 s accumulation. This method has been successfully applied to the determination of TA in tea and beer samples. In addition, the influence of potential interferents is examined. In the presence of bovine serum albumin, the peak current of TA decreases linearly due to the formation of a super-molecular complex.     

盐酸克伦特罗在玻碳电极上的伏安行为研究

采用电化学技术研究了盐酸克伦特罗(CLB)在玻碳电极上的电化学还原行为。在pH4.54的Britton Robinson缓冲液中,CLB于 0.38V(vs.Ag AgCl)左右处出现一个明显的方波溶出伏安还原峰,峰电流与CLB的浓度在3.0×10-7～1.0×10-5mol L范围内呈良好的线性关系,检出限为5.1×10-8mol L。该法可应用于模拟兔血清及尿样中CLB的测定。     

Application of a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole/carbon nanotube modified glassy carbon electrode for voltammetric determination of hydrazine in water samples

The electrochemical behaviour of hydrazine at a 1‐benzyl‐4‐ferrocenyl‐1H‐[1,2,3]‐triazole‐triazole/carbon nanotube modified glassy carbon electrode has been studied. The modified electrode shows an excellent electrocatalytic activity for the oxidation of hydrazine and accelerates electron transfer rate. The electrocatalytic current increases linearly with hydrazine concentration in the range 0.5–700.0 μm and the detection limit for hydrazine was 33.0 ± 2.0 nm . The diffusion coefficient (D = 2.5 ± 0.1 × 10^?5 cm² s^?1) and kinetic parameters such as the electron transfer coefficient, (α = 0.52) and the heterogeneous rate constant (k′ = 5.5 ± 0.1 × 10^?3 cm s^?1) for hydrazine were determined using electrochemical approaches. Finally, the method was employed for the determination of hydrazine in water samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Anodic Stripping Voltammetric Determination of Lead(II) Using Glassy Carbon Electrode Modified with Novel Calix[4]arene

Owingtothegrowingawarenessofleadpollutionandtoxicity,manytechniquesarecurrentlyemployedforthedeterminationoftracePbioninenvironmentalsamples .1Amongthem ,thedevelopmentofchemicallymodifiedelectrodes (CMEs)andapplicationsofanodicstrippingvoltammetry (ASV)havereceivedconsiderableattention .CMEsarecharacterizedbypurposefullyalteringtheirsur facecharacteristicstodisplaynewqualitiesthatcouldbeexploitedforanalyticalapplications .Thesekindsofelec trodesareinexpensiveandpossessmanyadvantagessuchas…     

Square wave voltammetric determination of nitrofurantoin in pharmaceutical formulations on highly boron-doped diamond electrodes at different boron-doping contents

The influence of the boron-doping levels in boron-doped diamond film electrodes on the electrochemical response of nitrofurantoin (NFT) and the development of an electroanalytical procedure for NFT determination were investigated. The investigations were carried out using the techniques of cyclic voltammetry and square wave voltammetry on diamond film electrodes with different boron-doping levels (i.e., 5000, 10,000 and 20,000 mg L⁻¹). The level of boron-doping in the diamond film electrodes influenced the electrochemical reduction of NFT. The appropriate cyclic voltammetric response of NFT was obtained with Britton-Robinson buffer at pH 4 and for diamond films doped with 10,000 and 20,000 mg L⁻¹ of boron. These two films were selected for the development of the electroanalytical procedure. The use of square wave voltammetry with the optimized parameters demonstrated a good linear relationship between the peak current and the NFT concentration for a wide range of concentration. The lower limit of detection for the electrodes doped with 10,000 and 20,000 mg L⁻¹ of boron were 2.69 × 10⁻⁸ mol L⁻¹ (6.40 μg L⁻¹) and 8.15 × 10⁻⁹ mol L⁻¹ (1.94 μg L⁻¹), respectively, while the lower limits of quantification were 8.96 × 10⁻⁸ mol L⁻¹ (21.33 μg L⁻¹) and 2.72 × 10⁻⁸ mol L⁻¹ (6.47 μg L⁻¹), respectively. The applicability of the proposed procedure was tested using a commercial pharmaceutical formulation of NFT, and the results were compared with the procedure recommended by the British Pharmacopeia. The proposed procedure was sensitive, accurate and precise for analysis of NFT and did not require complex preparations or renovations of the electrode surface. This presents the advantage of eliminating mercury waste and minimizing the adsorptive problems related to the use of other electrodic solid surfaces.     

Validated voltammetric method for the determination of some antiprotozoa drugs based on the reduction at an activated glassy carbon electrode

A sensitive electrochemical procedure based on reduction of secnidazole (I), tinidazole (II) and ornidazole (III) at a glassy carbon electrode (GCE) was introduced. A study of the variation of the peak current with solution variables such as pH, ionic strength, concentration of drugs, possible interference, and instrumental variables such as scan rate, pulse amplitude, preconcentration time, accumulation potential, has resulted in the optimization of the reduction signal for analytical purposes. Linear calibration plots were obtained over the concentration ranges of 50–800, 50–750 μg mL^?1 for I, and both (II, III) respectively, in Britton–Robinson buffer of pH 7. The relative standard deviations of five replicate measurements of 1.0 and 10.0 μg mL^?1 of I, II and III concentrations were 4.7%, 4.9% and 5.3%, and 2.2%, 2.6% and 2.8%, respectively. The limits of detection (LOD) for I, II and III were found to be 2 × 10^?10, 3 × 10^?10 and 2.5 × 10^?10 mol L^?1 and limits of quantification (LOQ) for I, II and III were found to be 4.0 × 10^?8, 1.2 × 10^?8 and 4.4 × 10^?8 mol L^?1, respectively. The optimal conditions were: E_acc = ?0.9 V, t_acc = 30 s, scan rate = 20 mV s^?1, pulse-height = 90 mV and Britton–Robinson buffer of pH 7. The method was applied for the determination of the cited drugs both in raw materials and in pharmaceutical preparations with satisfactory results and compared with the official reference method. Complete validation of the proposed method was also done.     

The catalytic adsorptive stripping voltammetric determination of chromium with TTHA and nitrate

A sensitive voltammetric method is presented for the determination of trace amounts of total chromium (Cr(III) and Cr(VI)) in natural waters, employing the square wave mode. The method is based on the preconcentration of the Cr(III)-TTHA complex by adsorption at the HMDE at the potential of –1.0 V vs. Ag/AgCl. The adsorbed complex is then reduced producing a response with a peak potential of –1.29 V and the peak height of the Cr(III) reduction is measured. The catalytic action of the nitrate ions on the Cr(III)-TTHA reduction has been elucidated using cyclic voltammetry. The adsorption of chromium complexes at the HMDE was investigated using out-of-phase a.c. voltammetry and the potential range of adsorption was determined.Based on these investigations optimal conditions for the determination of the total chromium concentration in the range 155–2000 ng 1^–1 have been established. The determination limit is 15 ng 1^–1 and the RSD is 3.5% for chromium concentrations 200 ng 1^–1.The usefulness and wide scope of this method for reliable and highly sensitive chromium analysis down to the ultra trace levels existing in various types of natural waters is demonstrated by determinations of the total chromium content in lake, sea and rain water.     

Simultaneous square-wave voltammetric determination of riboflavin and folic acid in pharmaceutical preparations

The square-wave voltammetric (SWV) behaviour of riboflavin and folic acid was studied at a static mercury drop electrode by square wave voltammetry. In 0.05M KCl (pH 5.89) a cathodic scan gave peaks at — 0.56 and — 0.87 V vs. Ag/AgCl for riboflavin and folic acid, respectively. The reduction peak currents are linearly dependent on the concentration of vitamins. Both vitamins can be simultaneously determined from the same voltammogram. The method proposed for the determination of riboflavin and folic acid in multivitamin tablets is very simple, rapid and does not involve time-consuming separation steps. The average contents of riboflavin and folic acid were found to be 14.8 ± 1.26% and 1.46 ± 2.66%, for tablet A and 9.86 ±1.40% and 1.47 ± 2.0% for tablet B, respectively.     

Electrochemical modification of a carbon paste electrode with poly (1,5-diaminonaphthalene) and copper-cobalt nanostructures for the determination of thioctic acid in real samples

This study used square-wave voltammetry and cyclic voltammetry to investigate the electrochemical oxidation of Thioctic Acid (TA) on a Carbon Paste Electrode (CPE) modified with copper-cobalt nanostructures and poly (1,5-Diaminonaphthalene). The voltammetric sensor was sensitive to the oxidation of TA. In addition, we optimized the effects of multiple cycles of deposition of Cu-Co nanostructures, and electro-polymerization of monomer 1,5-DAN, scan rate, and pH. The sensor showed good identification capabilities for TA. The linear responses obtained ranged from 0.6 μM to 150 μM with a detection limit of 0.48 μM for the modified CPE. The adsorption process controlled the oxidation of TA. We used the proposed sensor and method to determine TA in real samples.     

阿拉伯糖基有序介孔碳修饰电极检测盐酸奈福泮的研究

以阿拉伯糖为碳源,介孔硅(SBA-15)为模板剂,用硬模板法制备有序介孔碳材料,采用场发射扫描电镜(Scanning Electron Microscopy,SEM)、透射电子显微镜(Transmission Electron Microscope,TEM)、全自动比表面及孔隙度分析仪(Brunner Emmet Te...     

Sensitive Simultaneous Determination of o-Nitrophenol and p-Nitrophenol in Water by Surfactant-Mediated Differential Pulse Voltammetry

A simple, low-cost and sensitive electroanalytical method was developed for the simultaneous determination of p-nitrophenol and o-nitrophenol isomers in water samples at a glassy carbon electrode (CGE) in the presence of cationic surfactant. The electrochemical behavior of p-nitrophenol and o-nitrophenol was studied by cyclic voltammetry (CV) in 0.1?mol L^?1 acetate/acetic acid buffer (pH 3.70) in the presence and absence of cetylpyridinium bromide. The resolution of overlapped cathodic peaks potentials (E_pc) of isomers was successfully improved in the presence of 100.0?µmol L^?1 cetylpyridinium bromide, thus making this approach ideal for the simultaneous determination of isomers. Under the optimized conditions in 0.05?mol L^?1 HEPES buffer at pH 7.0 using differential pulse voltammetry (DPV) at a scan rate of 45?mV s^?1, pulse amplitude of 220?mV and modulation time of 10?ms, limits of detection 0.59?µmol L^?1 for p-nitrophenol and 1.14?µmol L^?1 for o-nitrophenol were obtained with linear ranges from 2.0 to 60.0?µmol L^?1 and 3.0 to 60.0?µmol L^?1, respectively. The intraday precision was assessed as relative standard deviation (%) for 20.0 and 40.0?µmol L^?1 concentrations were 4.30% and 2.41% for p-nitrophenol and 4.87% and 2.20% for o-nitrophenol, respectively. The developed method was applied for the determination of the isomers in lake water samples. The accuracy was attested by comparison with high-performance liquid chromatography with diode array detection (HPLC-DAD) as a reference analytical technique. Recovery values ranging from 90.3% to 111.8% also attested to the accuracy of method for analysis of real samples.     

A novel method for determination of magnesium in urine and water samples with mercury film-plated carbon paste electrode

A square wave adsorptive stripping voltammetric (SWAdSV) method for the indirect determination of trace amounts of magnesium with thiopentone sodium (TPS) as an electroactive ligand, at carbon paste mercury film electrode (CP-MFE) is proposed. It is observed that the increase of the square wave voltammetric cathodic peak current of TPS, under alkaline conditions, is linear with the increase of Mg concentration. Under optimum experimental conditions viz.; pH 10.75, 3×10⁻⁵ M TPS and 0.05 M phosphate buffer (Na₂HPO₄-NaH₂PO₄), a linear relation in the range 6×10⁻⁹ to 9×10⁻⁸ M Mg²⁺ (0.14-2.16 ppb), at 60 s deposition time, is obtained. The detection limit of Mg²⁺ is 0.14 ppb for 60 s deposition time with the relative standard deviation is 0.5% (n=5). The proposed method was successfully applied to the determination of magnesium in urine and tap water samples with satisfactory results. The data obtained are compared with the standard flame atomic absorption spectrophotometric method (FAAS).     

Nanoelectrode ensembles for the direct voltammetric determination of trace iodide in water

Procedures for the preparation and characterisation of ensembles of gold nanodisk electrodes (NEE) of 30 nm diameter are presented, in particular focusing on improvements in the signal/background current ratios and detection limits with respect to the electrochemical oxidation of iodide and its analytical determination in water samples. At NEEs iodide undergoes a quasi-reversible diffusion controlled oxidation with a slight shift in E _1/2 values and slightly higher peak to peak separation with respect to conventional gold disk electrodes. The double layer charging current at the NEE is significantly lower than at conventional electrodes so that the detection limit (DL) by cyclic voltammetry with NEEs in tap water is significantly lower than DL at the Au-disk millimetre-sized electrode (DL 0.3 µM at NEE vs. 4 µM for Au-disk). Finally, it is shown that NEEs in combination with square wave voltammetry can be applied for the direct determination of iodide in water samples from the lagoon of Venice, with a detection limit of 0.10 µM.     

CuO-nanoparticles modified carbon paste electrode for square wave voltammetric determination of lidocaine: Comparing classical and Box–Behnken optimization methodologies

In this research, copper oxide nanoparticles modified carbon paste electrode was developed for the voltammetric determination of lidocaine. The square wave voltammogram of lidocaine solution showed a well-defined peak between +0.5 and +1.5 V. Instrumental and chemical parameters influencing voltammetric response were optimized by both one at a time and Box–Behnken model of response surface methodology. The results revealed that there was no significant difference between two methods of optimization. The linear range was 1–2500 μmol L~(-1)(Ip= 0.11 C_(LH)+ 17.38, R~2= 0.999). The LOD and LOQ based on three and ten times of the signal to noise(S/N) were 0.39 and 1.3 μmol L~(-1)(n = 10),respectively. The precision of the method was assessed for 10 replicate square wave voltammetry(SWV)determinations each of 0.05, 0.5 and 1 μmol L~(-1) of lidocaine showing relative standard deviations 4.1%,3.7% and 2.1%, respectively. The reliability of the proposed method was established by application of the method for the determination of lidocaine in two pharmaceutical preparations, namely injection and gel.     

Electrochemical study of butylate: application to the analysis of water

A biochemical gas-sensor (bio-sniffer) was constructed for convenient measurement of odourless hydrogen peroxide (H₂O₂) vapour, which is harmful to skin and mucous membranes. An enzyme-immobilized membrane was fabricated by spreading the mixture of catalase and photo-crosslinkable polymer on a dialysis membrane. An H₂O₂ biosensor was constructed by attaching this catalase-immobilized membrane to the sensitive top of a Clark-type oxygen electrode, and the oxygen generation from the decomposition of H₂O₂ catalysed by catalase was measured amperometrically. This biosensor was first applied to the measurement of H₂O₂ solution and was able to quantify the concentrations of H₂O₂ solution from 0.02 to 10.0?mmol?L^?1. Then, this biosensor was applied to gaseous phase as a bio-sniffer and was able to detect the odourless H₂O₂ vapour with the calibration range from 0.5 to 30?ppm, where the threshold limit value assigned by the American Conference of Governmental Industrial Hygienists (1?ppm) is covered.     

Novel electrochemical procedure for the determination of metamitron

In this paper, a chronopotentiometric method for the determination of herbicide metamitron (MTM) using a glassy carbon electrode (GCE) and a thin film mercury electrode (TFME) as working electrodes is presented. MTM provided a well-defined reductive peak in the Britton–Robinson buffer on both working electrodes. Instrumental and chemical factors such as pH of the buffer, initial potential and reduction current influencing MTM chronopotentiometric response were optimised with the Box–Behnken experimental design. Under the optimal combination of factors, the analytical signal was linear in the MTM concentration range of 0.8–30 mg/L, with a detection limit of 68.53 µg/L using a TFME, and in the concentration range of 1–30 mg/L, with a detection limit of 92.91 µg/L using a GCE. The precision of the method was estimated as a function of repeatability and reproducibility, with the value of relative standard deviation lower than 2.6%. The applicability of the method was verified by direct analysis of MTM in spiked water samples and commercial pesticide formulations. The obtained results were in good agreement with those obtained using liquid chromatography/tandem mass spectrometry (LC-MS/MS) method, or with those labelled by the manufacturer. By using chronopotentiometry, neither extraction nor preconcentration procedures are necessary, thus making this method simple, cost-effective and more feasible for analytical routine analysis.     

Anodic Stripping Voltammetric Determination of Lead（Ⅱ） Using Glassy Carbon Electrode Modified with Novel Calix[4] arene

A new glassy carbon electrode modified with novel calix[4]‐arene derivative was prepared and then applied to the selective recognition of lead ion in aqueous media by cyclic and square wave voltammetry. A new anodic stripping peak at ? 0.92 V (vs. Ag/Ag⁺) in square wave voltammogram can be obtained by scanning the potential from ? 1.5 to ? 0.6 V, of which the peak current is proportional to the concentration of Pb²⁺. The modified electrode in 0.1 mol/L HNO₃ solution showed a linear voltammetric response in the range of 2.0 × 10–⁸–1.0 × 10–⁶ mol/L and a detection limit of 6.1 × 10–⁹ mol/L. In the modified glassy carbon electrode no significant interference occurred from alkali, alkaline and transition metal ions except Hg²⁺, Ag⁺ and Cu²⁺ ions, which can be eliminated by the addition of KSCN. The proposed method was successfully applied to determine lead in aqueous samples.     

Preconcentration and voltammetric determination of the herbicide metamitron with a silica-modified carbon paste electrode

A carbon paste electrode incorporating silica (Si-MCPE) was fabricated to accumulate Metamitron at the electrode surface. Several electroanalytical techniques were used to explore its reductive behaviour. The results indicate that the system is irreversible and fundamentally controlled by adsorption. The adsorptive stripping response has been evaluated with respect to accumulation time, deposition potential, scan rate, pH and other variables, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. In both cases a voltammetric peak is obtained, at –0.542 V (DPV) and –0.421 V (SWV) in Britton-Robinson buffer (pH 1.9). The detection limits were 3.66 × 10^–1 M and 4.22 × 10^–9 M for AdS-DPV and AdS-SWV, respectively. Under optimum conditions the Metamitron reduction peak gave two linear regions in the range from 4.0 × 10^–9 M to 8.0 × 10^–8 M by means of AdS-DPV, with a coefficient of variation of 2.19% (n = 10) for 1 × 10^–8 M herbicide solution. A method was developed for determination of Metamitron in soils, with a recovery of 98.8% and a coefficient of variation of 5.26% (0.01 g/g of soil).