Factors affecting the sorption behavior of Cs<Superscript>+</Superscript> and Sr<Superscript>2+</Superscript> using biosorbent material

In this study, saw dust has been used as precursor for production of low cost activated carbon using potassium hydroxide (KOH) and steam activation technique. The activated carbon was used to remove Cs⁺ and Sr²⁺ ions from aqueous solutions by batch operation, and the extent of adsorption was investigated as a function of solution pH, temperature, shaking time, and initial concentration. The influence of interfering ions was also investigated. The removal of metal ions was pH dependent and the adsorption capacity reaches its maximum 43% and 61.5% at pH 5.0 and 6.0 for Cs⁺ and Sr²⁺ ions, respectively. Thermodynamic studies showed different behaviours where an endothermic, non-spontaneous process was shown for Cs⁺ while an exothermic, spontaneous process was obtained for Sr²⁺. The kinetic data of both ions was described well by pseudo-second order rate equation. The two equilibrium models (Langmuir and Freundlich) have been also applied. Desorption studies indicated that HCl was the most effective desorbing eluent. The investigated adsorbent showed good results towards cesium and strontium removal from aqueous media that could be a promising method due to its low-cost and good efficiency.     

Adsorption of neodymium ions on activated charcoal from aqeous solutions

Summary A commercial activated charcoal has been tested as an adsorbent for the removal of neodymium ions from aqueous solutions. The adsorption behavior of neodymium ions on activated charcoal from aqueous solutions has been studied as a function of shaking time, neodymium ions concentration and concentration of different acids. Results reveal that the adsorption equilibrium is attained within 30 minutes, and diffusion of neodymium ions into the pores of activated charcoal controls the adsorption process. The adsorption process follows the first order kinetics. The Langmuir isotherm equation was obeyed well in the whole range of concentration studied. The influence of different cations and anions on the adsorption of neodymium ion from aqueous solutions have also been investigated. Approximately 98% of neodymium ions adsorbed onto activated charcoal could be recovered with 40 ml of 3M HNO₃ solutions.     

The removal of uranium(VI) from aqueous solutions onto activated carbon: kinetic and thermodynamic investigations

The adsorption of uranium(VI) from aqueous solutions onto activated carbon has been studied using a batch adsorber. The parameters that affect the uranium(VI) adsorption, such as contact time, solution pH, initial uranium(VI) concentration, and temperature, have been investigated and optimized conditions determined (contact time 240 min; pH 3.0+/-0.1; initial uranium concentration 100 mg/L; temperature 293.15 K). The experimental data were analyzed using sorption kinetic models (pseudo-first- and pseudo-second-order equations) to determine the equation that fits best our experimental results. Equilibrium isotherm studies were used to evaluate the maximum sorption capacity of activated carbon and experimental results showed this to be 28.30 mg/g. The Freundlich, Langmuir, and Dubinin-Radushkevich (D-R) models have been applied and the data correlate well with Freundlich model and that the sorption is physical in nature (the activation energy Ea=7.91 kJ/mol). Thermodynamic parameters (DeltaHads0=-50.53 kJ/mol, DeltaSads0=-98.76 J/mol K, DeltaGads(293.15 K)0=-21.61 kJ/mol) showed the exothermic heat of adsorption and the feasibility of the process.     

Adsorption of uranium from crude phosphoric acid using activated carbon

The adsorption of uranium from crude phosphoric acid has been investigated using conventional activated carbons. It was found that treatment with nitric acid oxidized the surface of activated carbon and significantly increased the adsorption capacity for uranium in acidic solutions. The parameters that affect the uranium(VI) adsorption, such as contact time, solution pH, initial uranium(VI) concentration, and temperature, have been investigated. Equilibrium data were fitted to a simplified Langmuir and Freundlich isotherms for the oxidized samples which indicate that the uranium adsorption onto the activated carbon fitted well with Langmuir isotherm than Freundlich isotherm. Equilibrium studies evaluate the theoretical capacity of activated carbon to be 45.24 g kg^?1.     

Adsorption of alkali and alkaline earth radionuclides on zeolite from water solutions

The adsorption of cesium and strontium ions from water solutions on zeolite has been investigated in presence of sodium, potassium, magnesium and calcium ions. Distribution ratios of cesium and strontium on the zeolite were determined in solutions of various compositions and solution volume to sorbent weight ratios (batch factor). Breakthrough curves for zeolite layers are reported.     

Adsorption of uranium on adsorbents produced from used tires

The present investigation deals with the potential use of adsorbents produced from used tires for the removal of uranium from aqueous solutions. Two different adsorbents were used including char and activated carbon produced from used tires. The surface area was larger on activated carbon. Adsorption experiments were carried out as a function of time, adsorbent concentration, pH and initial concentration of uranium. The adsorption kinetics was found to follow the Lagergren equation. The rate constants of intraparticle diffusion and mass transfer coefficients were calculated. It was shown that the equilibrium data could be fitted by the Langmuir and Freundlich equations. The adsorption of uranium in the presence of diffferent cations were also studied and the results were correlated with the ionic potential of the cations. Results obtained in the study demonstrate that the activated carbon produced from used tires can be considered as an adsorbent that has a commercial potential for uranium removal.     

Effect of alkali metals,alkaline earth metals and lanthanides on the adsorption of uranium on activated charcoal from aqueous solutions

Effects of alkali metals, alkaline earth metals and some lanthanides on the adsorption of uranium on activated charcoal from aqueous solutions have been studied. These effects are correlated with the ionic radii of metal ions present in the solutions. Adsorption capacity, X_m and binding energy contant, K for uranium adsorption were calculated from the Langmuir equätion. The mean energy of adsorption, E_s was calculated from adsorption energy constant, K, values determined from the Dubinin-Radushkevich isotherm equation. Wavelength dispersive X-ray fluorescence spectrometry was used for measuring the uranium concentration.     

Adsorption of strontium ions from aqueous solution on Pakistani coal

Summary The adsorption of strontium ions from aqueous solution on a Pakistani coal powder has been studied as a function of shaking time, amount of adsorbent, pH, and strontium ion concentration. Conditions for the maximum adsorption of strontium ions have been established. Results reveal that the diffusion of strontium ions into the pores of coal powder occurs during the adsorption process and intra-particle diffusion controls the kinetics of the process. The Langmuir and D-R adsorption equations are valid over the entire range of studied concentration. The influence of different anions on the adsorption of strontium ions was also studied.     

Sorption characteristics of an economical sorbent material used for removal radioisotopes of cesium and europium

Application study for the evaluation of sorption characteristics of sawdust as an economical sorbent material used for decontamination of radioisotopes cesium and europium from aqueous solution has been carried out in the present work. In this respect, sawdust (untreated and treated by HNO₃) has been prepared from the commercial processing of wood for furniture production. Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N₂ adsorption and DFT software. Radiotracer method onto sawdust from aqueous solutions was studied in a batch technique with respect to pH, contact time, temperature. The kinetics of adsorption of Eu³⁺ and Cs⁺ have been discussed using five kinetic models namely, pseudo-first-order model, pseudo-second-order model, Elovich equation, intraparticle diffusion model, and modified Freundlich equation that have been tested in order to analysis the experimental data. Kinetic parameters and correlation coefficients were determined. It was shown that the second-order kinetic equation could describe the sorption kinetics for two metal ions. The metal uptake process was found to be controlled by intraparticle diffusion. Thermodynamic parameters, such as ΔH, ΔG and ΔS, have been calculated by using the thermodynamic equilibrium coefficient obtained at different temperatures. The obtained results indicated that endothermic nature of sorption process for both ^152+154Eu and ¹³⁴Cs onto sawdust.     

Study of chromium(VI) adsorption onto modified activated carbons with respect to analytical application

Two different types of modification of activated carbon, by treatment with concentrated solution of HNO₃ and outgassing treatment at high temperature, were studied in order to obtain the most effective adsorption of chromium(VI) ions from water solution. The basic parameters affecting the adsorption capacity of Cr(VI) ions on modified activated carbons were studied in details and the effect of modifications of activated carbons has been determined by studying the initial runs of adsorption isotherms. The obtained Cr(VI) adsorption isotherms were well fitted in the Freundlich equation. The reduction of Cr(VI) to Cr(III) and further ion exchange mechanism of adsorption onto oxidizing activated carbon and surface precipitation to Cr(OH)₃ in case of outgassing activated carbon were found as the main adsorption mechanisms of Cr(VI) ions onto modified activated carbons. Presence of chlorides and nitrates in studied adsorption system strongly decreased the adsorption ability of Cr(VI) onto outgassing activated carbon and mechanism of this behavior is proposed.     

Adsorption of U(VI) from aqueous solution by sulfonated ordered mesoporous carbon

The sulfonated mesoporous carbon (CMK-3-SO₃H) prepared by functionalizing mesoporous carbon (CMK-3) via vapor transfer method has been explored for the removal and recovery of uranium from aqueous solutions. The influences of different experimental parameters such as solution pH, initial concentration, contact time and temperature on adsorption were investigated. The results showed that CMK-3-SO₃H has the highest uranium sorption capacity at initial pH of 5.0 and contact time of 120 min, and the adsorption process could be better described by the pseudo-second-order model and Langmuir isotherm. Selective adsorption studies showed that the CMK-3-SO₃H could selectively remove of U(VI), and the selectivity coefficients of mesoporous carbon in the presence of co-existing ions, Mg(II), Zn(II), Mn(II), Cu(II), Ni(II), Sr(II) and Hg(II) improved after functionalization.     

Adsorption of Pentafluorophenol onto Powdered,Granular, and Cloth Activated Carbons

In the present study, the adsorption of pentafluorophenol from aqueous solution onto granular activated carbon, powdered activated carbon, and activated carbon cloth has been investigated from the equilibrium and kinetic points of view. To the best of our knowledge, the removal of pentafluorophenol from aqueous solution onto activated carbon have not been reported in the literature. The experimental equilibrium data, suitably fitted by the Toth, Langmuir-Freundlich, and Redlich-Peterson isotherms, have shown that the cloth and powdered carbons exhibit the highest adsorption capacity. For all the investigated samples, the experimental kinetic data have been satisfactorily interpreted by a pseudo-second-order model. From the fitting results it has been observed that the highest rate constant and initial rate of adsorption is shown by powdered activated carbon.     

A study of the sorption properties of natural calcium clinoptilolite by using radioactive indicators

The sorption of monovalent ions (cesium, silver, thallium, mercury), bivalent ions (strontium, barium, lead, copper, cobalt, zinc) and polyvalent ions (cerium) on calcium clinoptilolite under dynamic conditions has been studied. Both the dynamic exchange capacities in the different break-through of the ions and the degree of the exchanging ions in sorption of different metal cations have been determined. The good selectivity of calcium clinoptilolite in relation to cesium and strontium is displayed in the presence of sodium. The influence of various factors on the sorption the thermal and radiation treatment of the sorbent, the pH and concentration of solutions, equilibration time, presence of alkali and alkali earth ions deactivating agents—EDTA, citric acid tartaric acid, and boric acid in solution has been studied. The optimum conditions of sorption have been determined. Experiments for the desorption of cesium and strontium have been carried out. The possibility to use calcium clinoptilolite for the purpose of deactivation of radioactive wastes is shown. The better sorption properties of that sorbent, compared to calcium clinoptilolite, can be explained by the higher aluminium content, as well as by a prevalence of calcium and magnesium in its ion exchange complex.     

Electrosorption of uranium ions on activated carbon fibers

A study on the electrosorption of uranium (U(VI)) ions onto a porous activated carbon fiber was performed to treat lagoon sludge containing 100 mg/L uranium and high concentration of chemical salts composed 3.8% NaNO₃, 19.8% NH₄NO₃, 1.9% Ca(NO₃)₂. The applied negative potential increased the adsorption kinetics and capacity in comparison to the open-circuit potential adsorption for uranium ions. When applying potential at −0.9 V (vs. Ag/AgCl) and pH 4, above 99% of the uranium is selectively removed from the 100 mg/L influent by electrosorption, and the cumulative amount of uranium for 50 h is about 600 mg_uranium/g_ACF. The high selectivity of elctrosorption process for uranium was probably caused by the difference of charge density of cations. More than 99% of adsorbed uranium ions was desorbed at a potential of +1.2 V and pH 3. The electrosorption of uranium onto the porous activated carbon fiber electrode is due to an ion exchange type reaction between the uranium ions and surface acid groups on carbon surface. Cyclic electrosorption test consisting of adsorption and desorption step shows that the activated carbon fiber electrode is easily regenerated in situ, indicating it is a reversible process.     

Adsorption Characteristics of Chromium(VI) on Granular Activated Carbon

The adsorption of Chromium(VI) from aqueous solutions was studied on different commercial grades of granular activated carbon namely Filtrasorb F‐400, F‐300, F‐200 and F‐100. The adsorption of Chromium (VI) on F‐400 carbon was found to be maximum in comparison to the other grades of carbon. The Chromium (VI) adsorption process in dilute aqueous solutions agreed with the Langmuir and Freundlich models and also obeyed first order kinetics. Metal sorption characteristics of as received activated carbons were measured in batch experiments. The maximum removal (60–65%) for different grades of raw carbon was observed at 25 °C with an initial concentration of 15.16 mg dm^?3. It is evident from the study that granular activated carbon holds a particular promise in the removal of metal ions from aqueous solutions.     

Sorption of strontium ions from aqueous solutions by oxidized multiwall carbon nanotubes

Multiwall carbon nanotubes (MWCNTs) oxidized by nitric acid solution were used to investigate the adsorption behavior of strontium from aqueous solutions similar to the nuclear waste media. The physical properties of both as produced and oxidized MWCNTs were studied by Boehm’s titration method and nitrogen adsorption/desorption. The results showed that the surface properties of MWCNTs such as specific surface area, functional groups and the total number of acid sites were improved after oxidation. Furthermore, the effect of solution conditions such as initial concentration of strontium(II), pH, ionic strength, MWCNT concentration and contact time were studied at room temperature. The results of this study showed that the adsorption of strontium(II) was significantly influenced by the pH value and the solution ionic strength. According to the Langmuir model, the maximum adsorption capacities of strontium(II) onto the as produced and oxidized MWCNTs were obtained as 1.62 and 6.62 mg g^?1, respectively. The contact time to reach equilibrium was 100 min. The good adsorption of strontium(II) on oxidized MWCNTs at the lower ionic strength, the relatively high pH and the short equilibrium time indicate that the oxidized MWCNTs have great potential applications in the field of the environmental protection.     

Efficiently removing cetyl trimethyl ammonium bromide from wastewater by graphene oxide

Cetyl trimethyl ammonium bromide (CTAB) containing wastewater from dressing plant may pose a detrimental threaten to mineral beneficiation and environment. The adsorption of CTAB in aqueous solutions by graphene oxide (GO) has been studied in this work. X-ray diffraction, X-ray photoelectron spectroscopy, Fourier-transform infrared spectrometer, and atomic force spectroscopy were used to characterize GO. The results indicated that the adsorption followed the Freundlich model could be well described by pseudo-second order kinetic model. The adsorption capacity was much bigger than activated carbon and many natural clay minerals. The adsorption process was endothermic, and the adsorption mechanism of CTAB onto GO was proven to be controlled by surface complexation, hydrogen bonding, and electrostatic attraction.     

Adsorption of Cd(II) Ions onto Activated Carbon Prepared from Hazelnut Husks

In this study, a batch adsorption of Cd(II) ions onto activated carbon (AC) produced from hazelnut husks were investigated. The factors controlling the adsorption process such as initial pH, agitation time, dosage and initial concentration have been examined. The AC was showed a high affinity to Cd(II) ions at pH values between 5.0 and 7.0. The equilibrium time was found to be 300 minutes. Cd(II) adsorption equilibrium was analyzed with both Langmuir and Freundlich isotherm equations and it was found that Langmuir equations fitted well with the experimental data. Maximum Cd(II) adsorption capacity of AC was calculated to be 20.9 mg g^?1. Cd(II) adsorption kinetics described well with the pseudo second order model. The activated carbon prepared from hazelnut husks is efficient sorbent material for the removal of Cd(II) ions from aqueous solutions.     

Validation of a Monte Carlo HPGe detector model against irradiated foil gamma-ray spectroscopy measurements

In order to separate and pre-concentrate uranium from aqueous phase, a novel silica-based adsorbent was prepared by impregnating nalidixic acid (HNA) into a macroreticular silica/polymer composite support (SiO₂-P) with a mean diameter of 60 μm. Adsorption behavior of uranium from aqueous solution onto the adsorbent was studied. Experimental results indicated that HNA/SiO₂-P showed strong adsorption for uranium in a wide range of pH from 3.5 to 10.0, and the maximum adsorption capacity was 35.4 mg g⁻¹. In addition, HNA/SiO₂-P exhibited good selectivity for U(VI) and showed weak or bare adsorption affinity to foreign ions. Kinetic and isotherm of uranium adsorption were in accordance with the pseudo-second-order kinetic model and Langmuir isotherm adsorption model, respectively. Moreover, U(VI) sorption was found to be an endothermic reaction and spontaneous under experimental state. The synthesized adsorbent showed an admirable stability at lower pH values in aqueous solution.

     

The removal and kinetic study of Mn,Fe, Ni and Cu ions from wastewater onto activated carbon from coconut shells

Activated carbon from coconut shells (ACCS) was synthesised and used for the removal of metal ions (manganese, iron, nickel and copper) from aqueous solutions. Two different adsorption models were used for analysing the data. Adsorption capacities were determined: copper ions exhibited the greatest adsorption on activated carbon obtained from coconut shells because of their size and pH conditions. Adsorption capacity varied as a function of the pH. Adsorption isotherms from aqueous solutions of heavy metals on ACCS were determined and were found to be consistent with Langmuir’s adsorption model. Adsorbent quantity and immersion enthalpy were studied. The results were compared with other adsorbents used in a prior study.