Cr3+,Yb3+,Er3+共掺磷酸盐铒玻璃转镜调Q激光性质研究

研究了Cr³⁺,Yb³⁺,Er³⁺共掺磷酸盐铒玻 璃转镜调Q激光性质.三种Er₂O₃掺杂浓度的激光实验结果表明，在Er₂O₃名义掺杂浓 度为0.5wt％时，玻璃的综合激 光性质最好，重复频率为0.1Hz时，它的激光阈值功率为14.5mJ，最大输出能量为9.6mJ ，斜率效率为0.55％.在同种实验条件下，比较了Cr14和Kigre公司生产的QE-7S激光性质参数，实验表明，前者激光阈值功率稍低，而后者的斜率效率和最大输出功率略高. 关键词： 3+-Yb³⁺-Er³⁺共掺')" href="#">Cr³⁺-Yb³⁺-Er³⁺共掺 磷酸 盐玻璃 光谱性质 激光性质     

LD泵浦的Er3+,Yb3+共掺杂磷酸盐铒玻璃激光性质

研究了三种不同铒离子浓度的Er3+,Yb3+共掺杂磷酸盐铒玻璃的光谱性质和激光性质,用2w,974nm半导体激光器作为泵浦源,在Er3+离子浓度为0.12×1020/cm3,0.48×1020/cm3,0.88×1020/cm3的Er3+,Yb3+共掺杂磷酸盐铒薄片玻璃中成功地实现了室温连续激光输出.讨论了铒离子掺杂浓度和样品厚度对激光性质的影响.通过比较发现在Yb3+离子浓度相当的条件下(1.5×1021/cm3),掺铒离子浓度为0.48×1020/cm3,厚度为2mm的铒玻璃具有较好的综合激光性能.它的最大激光输出功率达到43mw,斜率效率为10.2%,激光阈值为118mW,激光光谱范围为1527～1533nm,激光峰值波长为1530nm.     

1.54μm Er3+, Yb3+共掺玻璃激光器的速率方程及数值分析

LD抽运共掺Er,Yb玻璃激光器中的跃迁过程较复杂,针对双掺离子之间的能量传递和Er3 +的多种跃迁过程,给出了详细的准三能级系统的速率方程,在合理简化后进行了数值分析,分析了Er3+掺杂浓度和介质长度、抽运光斑、输出镜透过率、谐振腔长、抽运光的椭圆度等因素对激光阈值及斜率效率的影响.     

1.54μmEr3+,Yb3+共掺玻璃激光器的速率方程及数值分析

LD抽运共掺Er,Yb玻璃激光器中的跃迁过程较复杂,针对双掺离子之间的能量传递和Er3+的多种跃迁过程,给出了详细的准三能级系统的速率方程,在合理简化后进行了数值分析,分析了Er3+掺杂浓度和介质长度、抽运光斑、输出镜透过率、谐振腔长、抽运光的椭圆度等因素对激光阈值及斜率效率的影响. 关键词： 1.54μm激光 Er3+玻璃 速率方程 数值分析     

Yb3+掺杂浓度对Er3+/Yb3+共掺SiO2-Al2O3-La2O3玻璃光谱性质的影响

测量了不同Yb3+ 离子掺杂浓度下 ,Er3+ /Yb3+ 共掺SiO2 Al2 O3 La2O3玻璃的吸收光谱、荧光光谱和Yb3+离子2 F5/ 2 的能级寿命 ,应用迈克康伯 (McCumber)理论计算了Er3+ 的受激发射截面σemi,讨论了Yb3+ 离子浓度对其自身吸收性质、Er3+ 离子发光性质 ,以及Yb3+ →Er3+ 能量传递效率 (η)的影响 ,初步探明该基质玻璃中Yb3+ 离子掺杂数浓度的最佳范围为 3 .94× 1 0 2 0 cm- 3至 5 .92× 1 0 2 0 cm- 3,在此掺杂范围内 ,Yb3+ 离子的最大吸收系数为9.8cm- 1 ,Er3+ 的峰值发射截面和Yb3+ →Er3+ 能量传递效率 (η)分别为 0 64× 1 0 - 2 4 m2 和 92 %。     

Yb3+:Y2O3透明陶瓷激光器获得5 W连续激光输出

用带尾纤输出的激光二极管作为抽运源,采用端面抽运10％Yb^3 ：Y2O3多晶透明陶瓷的方式获得了连续激光输出。抽运阈值功率为5．6W,当陶瓷介质吸收的抽运功率为31．11W时,Yb^3 ：Y2O3多晶透明陶瓷获得了最大连续激光输出功率5．48W。光—光转换效率为17．6％,斜率效率为25％。同时在激光实验过程中,没有发现饱和现象,因此采用更高功率的激光二极管作为抽运源,陶瓷的激光输出功率会得到进一步提高。这一研究成果表明,多晶透明陶瓷是一种非常有潜力的激光增益介质。     

LD抽运Er3+,Yb3+共掺磷酸盐玻璃被动调Q激光器的理论分析和数值计算

研究了以Co2+:MgAl2O4晶体为饱和吸收体的LD抽运Er3+,Yb3+共掺磷酸盐玻璃激光器.针对双掺离子之间的能量传递和Er3+的多种跃迁过程,结合Co2+:MgAl2O4晶体中Co2+离子的饱和吸收特性,给出了详尽的速率方程,在其基础上进行了数值分析,分析了输出镜透过率、激光介质长度、谐振腔长度、腔内往返损耗、饱和吸收体长度对激光阈值、峰值功率、单脉冲能量以及脉冲宽度的影响.     

光纤环形镜线形腔掺Er3+光纤激光器输出特性的数值分析

在分析光纤环形镜工作原理的基础上,给出了基于光纤环形镜的线形腔掺Er3+光纤激光器相位和幅度的振荡条件.通过求解速率方程,理论分析了其输出特性,获得了稳态条件下激光器输出功率、阈值泵浦功率和斜率效率的解析表达式.推导出激光器工作所需掺Er3+光纤最短长度,并在给定泵浦光功率时,在特定输出波长上获得最大输出功率所需最佳掺Er3+光纤长度的表达式,且通过实验进行了验证.     

(ZnO)_(1-x-y)(P_2O_5)_x(B_2O_3)_y玻璃的环境稳定性和红外光致发光(英文)

Er3+掺杂的(ZnO)1-x-y(P2O5)x(B2O3)y玻璃具有优良的光学性质。沸水煮沸实验结果表明,该类玻璃具有较高的环境稳定性。与(Er2O3)z(ZnO)1-x-z(P2O5)x-z类玻璃相比,Er3+掺杂的该类玻璃在1.5μm峰值位置的光谱半峰全宽超过110 nm,而且具有较高的猝灭浓度。     

微型化LD泵浦Er~(3+),Yb~(3+)共掺磷酸盐玻璃被动调Q激光器

报道了一种主要应用于激光测距的微型化激光二极管泵浦Er3+/Yb3+共掺磷酸盐玻璃被动调Q激光器。采用中心波长940nm的二极管作为泵浦源,Er3+/Yb3+共掺磷酸盐玻璃作为增益介质,Co2+:MgAl2O4作为被动调Q晶体,通过优化增益介质和被动调Q晶体参数,获得了最佳的增益介质长度和被动调Q晶体初始透过率。当泵浦能量14mJ,重复频率10Hz,泵浦脉宽5ms时,获得了单脉冲能量480μJ,脉宽5ns,峰值功率大于20kW的激光输出,激光光束质量因子为1.2。     

多体系多波长计算光度法同时测定镧铈镨钕钐铕钆

本文以DBC-偶氮氯膦为显色剂,并且在显色体系中加入不同量的EDTA-Na2P2O7作为竞争配位剂,使得七组分轻稀土组分间吸收光谱灵敏度的差别逐渐加大,从而增加了轻稀土混合物体系组分间吸收光谱的线性独立性.利用数值稳定性较强的约束优化算法--可变容差法处理光谱数据,对不同浓度比例的七组分轻稀土混合物体系(La3+,Ce3+,Pr3+,Nd3+,S m3+,Eu3+,Gd3+)的测定,取得了较满意的结果.     

CaZrO_3∶Ln(Ln=Pr~(3+),Sm~(3+),Tb~(3+),Dy~(3+),Tm~(3+))荧光粉的制备与光谱调控

采用高温固相法合成了稀土离子Pr3+、Sm3+、Tb3+、Dy3+、Tm3+掺杂的正交相CaZrO3荧光粉。利用X射线粉末衍射(XRD)对样品的结构进行表征,并通过荧光光谱对其发光性质进行了研究。在适当近紫外或蓝光激发下,CaZrO3∶Pr3+产生很强的绿光发射,CaZrO3∶Sm3+可发射550~700 nm的红橙光,Tm3+在CaZrO3中可获得良好的蓝光发射。研究结果表明,通过改变CaZrO3中的掺杂离子可实现其发光颜色的调控,稀土离子掺杂CaZrO3荧光粉是很有潜力的新型发光材料。     

Photoacoustic Spectra of Sm3+, Eu3+, Dy3+ Complexes

The complexes crystals of Sm(Ac)3.4H₂O, Eu(Ac)3.4H₂O and a new complex Dy2(Ac)(NO3)4.12H₂O were synthesized and their PA spectra were determined firstly. All their PA spectra absorptions are interpreted. The fluorescence properties of Sm³⁺, Eu³⁺, Dy³⁺ and the relaxation process models were studied by their PA spectra.     

5d-4f luminescence of Nd3+, Gd3+, Er3+, Tm3+, and Ho3+ ions in crystals of alkaline earth fluorides

The vacuum ultraviolet emission spectra of alkaline-earth fluoride (CaF₂, SrF₂, BaF₂) crystals with rare earth impurity ions (Nd, Gd, Er, Tm, Ho) have been investigated. The main luminescence bands are described well by the transitions from the lowest excited 5d state to different 4f levels of rare earth ions.     

Photoluminescence investigations of Li2SiO3:Ln (Ln=Er3+, Eu3+, Dy3+, Sm3+) phosphors

In this study, we report a comprehensive structural and photoluminescence (PL) study on lithium metasilicate (Li₂SiO₃) phosphor ceramics doped with four rare earth (RE) ions. X-ray diffraction (XRD) patterns show a dominant phase, characteristic of the orthorhombic structure Li₂SiO₃ compound and the presence of dopants has no effect on the basic crystal structure of the material. The first excited state Er³⁺ luminescence at 1.54 μm arises from a sharp atomic-like radiative transition between the ⁴I_13/2 state and the ⁴I_15/2 state (ground level) under a 532 nm line of an Ar ion laser excitation. Sm doped samples showed Sm³⁺ emission characteristics corresponding to the some ⁴G_5/2→⁶H_j (j=5/2,9/2,11/2) transitions indicating a strong crystal-field effect. PL spectra of Eu doped material exhibited peaks corresponding to the ⁵D₀→⁷F_j (j=0,1,2,3 and 4) transitions under 405 nm excitation. The dominant red color emission at 612 nm from the hypersensitive (⁵D₀→⁷F₂) transition of Eu³⁺ indicates the inversion antisymmetry crystal field around Eu³⁺ ion, which is favorable to improve the red color purity. Dy doped samples showed the Dy³⁺ emission characteristic due to the ⁴F_9/2→⁶H_13/2 transition. Their relative intensity ratios also suggested the presence of a symmetric environment around the metal ion. We suggest that lithium metasilicate has enough potential candidates to be a phosphor material.     

Lithium ion conductivity of the B-site substitution in Li3xLa0.67−xRE y III Ti1−2yPyO3 system (REIII=Sc3+, Y3+, Nd3+, Sm3+, Eu3+, Yb3+)

The B-site substituted perovskite solid solution systems Li_3xLa_0.67−xRE_yTi_1−2yP_yO₃ (RE=Sc, Y, Nd, Sm, Eu, Yb) have been investigated. Perovskite solid solutions formed in the range of x=0.10, y<0.10 for RE=Sc³⁺, Y³⁺, Yb³⁺, x=0.10, y≤0.05 for RE=Nd³⁺, Sm³⁺, Eu³⁺. Li_0.3La_0.57Nd_0.05Ti_0.9P_0.05O₃ has the highest bulk conductivity of 4.31×10⁻⁴ S·cm⁻¹ and the highest total conductivity of 2.52×10⁻⁴ S·cm⁻¹ at room temperature in all prepared compositions. The compositions have low activation energies of about 24–30 kJ/mol in the temperature ranges of 298–523 K. SEM studies showed that the sample made by solid-state reaction has a sphere-like morphology and a rough particle with particle size of about 50 μm. The research results also indicated that the reaction temperature decreases and the electrochemical stabilities of the titanate-based perovskite-type solid solutions are improved by using RE³⁺ and P⁵⁺ replaced Ti⁴⁺ on B-site in the Li_3xLa_0.67−xTiO₃ parent.     

ZBLAN玻璃中Nd~(3+),Tm~(3+),Yb~(3+)的上转换发光特性

采用高温固相法制备了Nd,Tm和Yb掺杂的ZBLAN玻璃上转换材料.Tm3+,Yb3+的摩尔浓度分别固定为0.01%,0.3%,Nd3+摩尔浓度变化范围为0.1%～2%.在室温下,测试了样品在300～1 000nm间的吸收光谱.在798 nm近红外光激发下,测试了样品的上转换光谱.实验发现,样品在798 nm红外光激发下发出了较强的多波段(红,蓝和绿)的可见光.由上转换可见光各波段的发射谱线,给出了能级跃迁机制.蓝光主要来源于Tm3+的激发态1G4到基态3H6的跃迁,绿光来源于Nd3+的2H7/2到基态4I9/2的跃迁,红光来源于Nd3+的2H11/2到基态4i9/2的跃迁.研究发现,在Nd3+,Tm3+,Yb3+:ZBLAN玻璃样品中存在激发态吸收,能最转移和交叉弛豫等上转换过程.其发光机理是Nd3+,TM3+和Yb3+离子之间的能量转移.根据Nd3+摩尔浓度不同其上转换发光强度不同,分析了掺入稀土的浓度对上转换发光效率的影响.当Nd3+浓度为1.5%(摩尔分数)时上转换发光最强,大于1.5%后发光开始减弱.