Flow and heat transfer of an electrically conducting third grade fluid past an infinite plate with partial slip

The effects of partial slip on the steady flow and heat transfer of an electrically conducting, incompressible, third grade fluid past a horizontal plate subject to uniform suction and blowing is investigated. Two distinct heat transfer problems are studied. In the first case, the plate is assumed to be at a higher temperature than the fluid; and in the second case, the plate is assumed to be insulated. The momentum equation is characterized by a highly nonlinear boundary value problem in which the order of the differential equation exceeds the number of available boundary conditions. Numerical solutions for the governing nonlinear equations are obtained over the entire range of physical parameters. The effects of slip, magnetic parameter, non-Newtonian fluid characteristics on the velocity and temperature fields are discussed in detail and shown graphically. It is interesting to find that the velocity and the thermal boundary layers decrease with an increase in the slip, and as the slip increases to infinity, the flow behaves as though it were inviscid.     

HOPF BIFURCATION OF A NONLINEAR RESTRAINED CURVED PIPE CONVEYING FLUID BY DIFFERENTIAL QUADRATURE METHOD

This paper proposes a new method for investigating the Hopf bifurcation of a curved pipe conveying fluid with nonlinear spring support. The nonlinear equation of motion is derived by forces equilibrium on microelement of the system under consideration. The spatial coordinate of the system is discretized by the differential quadrature method and then the dynamic equation is solved by the Newton-Raphson method. The numerical solutions show that the inner fluid velocity of the Hopf bifurcation point of the curved pipe varies with different values of the parameter,nonlinear spring stiffness. Based on this, the cycle and divergent motions are both found to exist at specific fluid flow velocities with a given value of the nonlinear spring stiffness. The results are useful for further study of the nonlinear dynamic mechanism of the curved fluid conveying pipe.     

环形截面螺旋管道内二次流动特性的研究

从曲线柱坐标系下的N-S方程出发,以曲率和挠率为小参数,采用摄动法求解了环形截面螺旋管道内的黏性流动,给出了完全二阶摄动解,结果表明：当挠率为零时,二次流表现为上下对称的四个涡;当挠率不为零,涡的对称性遭到破坏,二次涡的强度和个数受De数和环形截面内外径之比δ的影响,轴向速度最大值在De数较小时靠近管道的内侧,随着De数的增加,其最大值向外侧移动。     

Hydromagnetic flow through uniform channel bounded by porous media

The combined effects of the magnetic field, permeable walls, Darcy velocity, and slip parameter on the steady flow of a fluid in a channel of uniform width are studied. The fluid flowing in the channel is assumed to be homogeneous, incompressible,and Newtonian. Analytical solutions are constructed for the governing equations using Beavers-Joseph slip boundary conditions. Effects of the magnetic field, permeability,Darcy velocity, and slip parameter on the axial velocity, slip velocity, and shear stress are discussed in detail. It is shown that the Hartmann number, Darcy velocity, porous parameter, and slip parameter play a vital role in altering the flow and in turn the shear stress.     

Slip and induced magnetic field effects on peristaltic transport of Johnson-Segalman fluid

The peristaltic flow of a Johnson-Segalman fluid in a planar channel is investigated in an induced magnetic field with the slip condition.The symmetric nature of the flow in a channel is utilized.The velocity slip condition in terms of shear stresses is considered.The mathematical formulation is presented,and the equations are solved under long wavelength and low Reynolds number approximations.The perturbation solutions are established for the pressure,the axial velocity,the micro-rotation component,the stream function,the magnetic-force function,the axial induced magnetic field,and the current distribution across the channel.The solution expressions for small Weissenberg numbers are derived.The flow quantities of interest are sketched and analyzed.     

Unsteady MHD flow over exponentially stretching sheet with slip conditions

The present paper examines the hydromagnetic three-dimensional flow induced by a stretched surface. An incompressible material saturates the porous medium. Velocity and thermal slip boundary conditions are considered. Suitable transformations are used to obtain the nonlinear ordinary differential equations. Series solutions of the resulting systems are constructed. The effects of various pertinent parameters on the axial velocity and temperature distributions are analyzed graphically. The skin friction and the Nusselt number are computed numerically and graphically.     

Stokes flow of micro-polar fluids by peristaltic pumping through tube with slip boundary condition

This paper studies the Stokes flow of micro-polar fluids by peristaltic pumping through the cylindrical tube under the effect of the slip boundary condition. The motion of the wall is governed by the sinusoidal wave equation. The analytical and numerical solutions for the axial velocity, the micro-polar vector, the stream function, the pressure gradient, the friction force, and the mechanical efficiency are obtained by using the lubrication theory under the low Reynolds number and long wavelength approximations. The impacts of the emerging parameters, such as the coupling number, the micro-polar parameter, the slip parameter on pumping characteristics, the friction force, the velocity profile, the mechanical efficiency, and the trapping phenomenon are depicted graphically. The numerical results infer that large pressure is required for peristaltic pumping when the coupling number is large, while opposite behaviors are found for the micro-polar parameter and the slip parameter. The size of the trapped bolus reduces with the increase in the coupling number and the micro-polar parameter, whereas it blows up with the increase in the slip parameter.     

同轴圆柱间滑移旋转流动问题的同伦解析解

从理论上研究了具有延伸柱面的同轴圆柱间滑移流动问题.通过引入适当的相似变换将控制方程组转化为一类非线性边值问题, 利用同伦分析方法首次获得问题的近似解析解, 分析讨论滑移参数、雷诺数和内外筒半径比对流动的影响.结果表明: 滑移边界参数对剪切应力有较大的影响, 滑移边界小的流体对壁面和边界层内流场施加了更大的剪切力; 增大雷诺数Re, 能增大内筒的壁面剪切力和扭矩; 内外筒半径比对流动结构也有较大的影响, 内筒半径固定, 增大外筒半径能够减少内筒的纵向剪切力.      

Flow of Particulate-Fluid Suspension in a Channel with Porous Walls

The problem of the dispersed particulate-fluid two-phase flow in a channel with permeable walls under the effect of the Beavers and Joseph slip boundary condition is concerned in this paper. The analytical solution has been derived for the longitude pressure difference, stream functions, and the velocity distribution with the perturbation method based on a small width to length ratio of the channel. The graphical results for pressure, velocity, and stream function are presented and the effects of geometrical coefficients, the slip parameter and the volume fraction density on the pressure variation, the streamline structure and the velocity distribution are evaluated numerically and discussed. It is shown that the sinusoidal channel, accompanied by a higher friction factor, has higher pressure drop than that of the parallel-plate channel under fully developed flow conditions due to the wall-induced curvature effect. The increment of the channel’s width to the length ratio will remarkably increase the flow rate because of the enlargement of the flow area in the channel. At low Reynolds number ranging from 0 to 65, the fluids move forward smoothly following the shape of the channel. Moreover, the slip boundary condition will notably increase the fluid velocity and the decrease of the slip parameter leads to the increment of the velocity magnitude across the channel. The fluid-phase axial velocity decreases with the increment of the volume fraction density.     

MHD boundary-layer flow of an upper-convected Maxwell fluid in a porous channel

Two-dimensional magnetohydrodynamic (MHD) boundary layer flow of an upper-convected Maxwell fluid is investigated in a channel. The walls of the channel are taken as porous. Using the similarity transformations and boundary layer approximations, the nonlinear partial differential equations are reduced to an ordinary differential equation. The developed nonlinear equation is solved analytically using the homotopy analysis method. An expression for the analytic solution is derived in the form of a series. The convergence of the obtained series is shown. The effects of the Reynolds number Re, Deborah number De and Hartman number M are shown through graphs and discussed for both the suction and injection cases.     

Jeffery-Hamel flow of non-Newtonian fluid with nonlinear viscosity and wall friction

A Jeffery-Hamel(J-H) flow model of the non-Newtonian fluid type inside a convergent wedge(inclined walls) with a wall friction is derived by a nonlinear ordinary differential equation with appropriate boundary conditions based on similarity relationships. Unlike the usual power law model, this paper develops nonlinear viscosity based only on a tangential coordinate function due to the radial geometry shape. Two kinds of solutions are developed, i.e., analytical and semi-analytical(numerical) solutions with suitable assumptions. As a result of the parametric examination, it has been found that the Newtonian normalized velocity gradually decreases with the tangential direction progress. Also, an increase in the friction coefficient leads to a decrease in the normalized Newtonian velocity profile values. However, an increase in the Reynolds number causes an increase in the normalized velocity function values. Additionally, for the small values of wedge semi-angle, the present solutions are in good agreement with the previous results in the literature.     

Peristaltic motion of a power-law fluid in an asymmetric channel

The flow of a power-law fluid is investigated in an asymmetric channel caused by the movement of peristaltic waves with the same speed but with different amplitudes and phases on the flexible walls of the channel. The differential equation governing the flow is non-linear and can admit non-unique solutions. There exist two different physically meaningful solutions one satisfying the boundary conditions at the upper wall and the other at the lower wall. The effects of the power-law nature of the fluid on the pumping characteristics and axial velocity are studied in detail.     

Slip effects on a mixed convection flow of a third-grade fluid near the orthogonal stagnation point on a vertical surface

A mixed convection flow of a third-grade fluid near the orthogonal stagnation point on a vertical surface with slip and viscous dissipation effects is investigated. The governing partial differential equations for the third-grade fluid are converted into a system of nonlinear ordinary differential equations by using a similarity transformation. The effects of various parameters, including the Weissenberg number, third-grade parameter, local Reynolds number, Prandtl number, Eckert number, mixed convection parameter, velocity slip, and thermal slip on the velocity and temperature profiles, local skin friction coefficient, and local Nusselt number are discussed.     

DYNAMIC RESPONSES OF VISCOELASTIC AXIALLY MOVING BELT

Based on the Kelvin viscoelastic differential constitutive law and the motion equation of the axially moving belt, the nonlinear dynamic model of the viscoelastic axial moving belt was established. And then it was reduced to be a linear differential system which the analytical solutions with a constant transport velocity and with a harmonically varying transport velocity were obtained by applying Lie group transformations. According to the nonlinear dynamic model, the effects of material parameters and the steady-state velocity and the perturbed axial velocity of the belt on the dynamic responses of the belts were investigated by the research of digital simulation . The result shows:1) The nonlinear vibration frequency of the belt will become small when the relocity of the belt increases . 2) Increasing the value of viscosity or decreasing the value of elasticity leads to a deceasing in vibration frequencies. 3) The most effects of the transverse amplitudes come from the frequency of the perturbed veloc     

Heat transfer in laminar entrance region of a flat channel for the temperature boundary condition of the third kind

To explore the influence of the developing flow in a flat channel on the laminar forced convection heat transfer, the non-linear momentum and the linear energy equation are solved successively by employing the Galerkin-Kantorowich method of variational calculus. Assuming constant fluid properties, negligible axial diffusion and temperature boundary condition of the third kind, semi analytic solution for velocity and temperature is derived. The local Nusselt numbers are tabulated for various values of Biot and Prandtl number.     

On the reduction of some second-order nonlinear ODEs in physics and mechanics to first-order nonlinear integrodifferential and Abel’s classes of equations

Second-order ordinary differential equations (ODEs) with strong nonlinear stiffness terms (cubic nonlinearities) governing wave motions, dynamic crack propagations, nonlinear oscillations etc. in physics and nonlinear mechanics are analyzed. Selecting as guide line a second-order nonlinear ODE of the form of the forced Duffing equation and using admissible functional transformations it is possible to reduce it to an equivalent first-order nonlinear integrodifferential equation. The reduced equation is exact. In the limits of small or large values of the parameter characterizing this nonlinear problem, it is shown that further reductions lead to a nonlinear ODE of the Abel classes. Taking into account the known exact analytic solutions of this equivalent equation it is proved that there does not exist an exact analytic solution of this type of equations. However, in cases when convenient functional relations connecting all parameters of the corresponding null equation and the characteristics of the driving force exist, approximate analytic solutions to the problem under consideration are provided.     

Electrokinetic flow and energy conversion in a curved microtube

Curved channels are ubiquitous in microfluidic systems. The pressuredriven electrokinetic flow and energy conversion in a curved microtube are investigated analytically by using a perturbation analysis method under the assumptions of the small curvature ratio and the Reynolds number. The results indicate that the curvature of the microtube leads to a skewed pattern in the distribution of the electrical double layer (EDL) potential. The EDL potential at the outer side of the bend is larger than that at the inner side of the bend. The curvature shows an inhibitory effect on the magnitude of the streaming potential field induced by the pressure-driven flow. Since the spanwise pressure gradient is dominant over the inertial force, the resulting axial velocity profile is skewed into the inner region of the curved channel. Furthermore, the flow rate in a curved microtube could be larger than that in a straight one with the same pressure gradient and shape of cross section. The asymptotic solutions of the axial velocity and flow rate in the absence of the electrokinetic effect are in agreement with the classical results for low Reynolds number flows. Remarkably, the curved geometry could be beneficial to improving the electrokinetic energy conversion (EKEC) efficiency.     

Effects of partial slip on boundary layer flow past a permeable exponential stretching sheet in presence of thermal radiation

An analysis is presented to describe the boundary layer flow and heat transfer towards a porous exponential stretching sheet. Velocity and thermal slips are considered instead of no-slip conditions at the boundary. Thermal radiation term is incorporated in the temperature equation. Similarity transformations are used to convert the partial differential equations corresponding to the momentum and heat equations into highly non-linear ordinary differential equations. Numerical solutions of these equations are obtained by shooting method. It is found that the fluid velocity and temperature decrease with increasing slip parameter. Temperature is found to decrease with an increase of thermal slip parameter. Thermal radiation enhances the effective thermal diffusivity and the temperature rises.     

Active and passive controls of nanoparticles in Maxwell stagnation point flow over a slipped stretched surface

A steady stagnation-point flow of an incompressible Maxwell fluid towards a linearly stretching sheet with active and passive controls of nanoparticles is studied numerically. The momentum equation of the Maxwell nanofluid is inserted with an external velocity term as a result of the flow approaches the stagnation point. Conventional energy equation is modified by incorporation of nanofluid Brownian and thermophoresis effects. The condition of zero normal flux of nanoparticles at the stretching surface is defined to impulse the particles away from the surface in combination with nonzero normal flux condition. A hydrodynamic slip velocity is also added to the initial condition as a component of the entrenched stretching velocity. The governing partial differential equations are then reduced into a system of ordinary differential equations by using similarity transformation. A classical shooting method is applied to solve the nonlinear coupled differential equations. The velocity, temperature and nanoparticle volume fraction profiles together with the reduced skin friction coefficient, Nusselt number and Sherwood number are graphically presented to visualize the effects of particular parameters. Temperature distributions in passive control model are consistently lower than in the active control model. The magnitude of the reduced skin friction coefficient, Nusselt number and Sherwood number decrease as the hydrodynamic slip parameter increases while the Brownian parameter has negligible effect on the reduced heat transfer rate when nanoparticles are passively controlled at the surface. It is also found that the stagnation parameter contributes better heat transfer performance of the nanofluid under both active and passive controls of normal mass flux.     

Effect of Viscous Dissipation on the Boundary Layer Flow and Heat Transfer Past a Permeable Stretching Surface Embedded in a Porous Medium with a Second-Order Slip Using Chebyshev Finite Difference Method

This article investigates a theoretical and numerical study for the effect of viscous dissipation on the steady flow with heat transfer of Newtonian fluid toward a permeable stretching surface embedded in a porous medium with a second-order slip and thermal slip. The governing nonlinear partial differential equations are converted into nonlinear ordinary differential equations (ODEs) using similarity variables. The resulting ODEs are successfully solved numerically with the help of Chebyshev finite difference method. Graphically results are shown for non-dimensional velocities and temperature. The effects of the porous parameter, the suction (injection) parameter, Eckert number, first- and second-order velocity slip parameter, the thermal slip parameter and the Prandtl number on the flow and temperature profiles are presented. Moreover, the local skin-friction and Nusselt numbers are presented. A comparison of numerical results is made with the earlier published results under limiting cases.