新型光纤光栅水声传感器的研究

提出了一种新型的光纤布拉格光栅(FBG)水声传感探头结构以及光纤光栅传感信号的自解调方法。利用一对匹配光栅构成推挽结构,实现了传感-解调的合二为一,大大地减小了系统的复杂度;并通过筒状弹性体结构,解决了裸光纤光栅测量水声信号的灵敏度过小的问题,并具有温度补偿作用。仿真与初步实验结果表明,该水听器探头的测量动态范围超过100 dB,在100~200 dB re 1μPa的水声压范围内,测量灵敏度为0.36 nm/Mpa。     

Development of an optical fiber hydrophone with fiber Bragg grating

A new type of optical fiber hydrophone is constructed with a fiber Bragg grating (FBG) based on the intensity modulation of laser light in an FBG under the influence of sound pressure. The FBG hydrophone shows linearity, with dynamic range about 70 dB. It can measure amplitude and phase of an acoustic field in real time, and operates in a wide range of acoustic frequency, at least from 1 kHz to 3 MHz. No signal distortion is observed in the detected signal. Because of the simplicity in its operating principle and geometry, an FBG hydrophone is expected to be an acoustic sensor of high practicality compared to a conventional optical fiber hydrophone.     

Pressure sensing utilizing linear cavity erbium-doped fiber laser

In this paper, we report a fiber laser pressure sensor based on linear cavity erbium-doped fiber laser. The fiber laser structure comprises of an erbium-doped fiber amplifier, a circulator, an optical coupler and a fiber Bragg grating (FBG) which acts simultaneously as a lasing wavelength selecting components as well as a pressure sensor. The FBG is fitted to the shock tube where the pressure is applied. The fiber laser pressure sensor has a low threshold power of 7 mW, an output power of 2.28 mW and an optical signal to noise ratio over 55 dB. The proposed fiber laser sensor is expected to be an attractive choice for long-distance pressure monitoring.     

基于光纤环形激光器和光放大的100 km光纤布拉格光栅传感系统

在基于掺铒光纤-拉曼混合放大的可调光纤环形激光器的光纤布拉格光栅(FBG)传感系统结构基础上,提出了延长传感距离的新方法。该方法以环形掺铒光纤激光器作为光源,采用双波长拉曼放大的方法对信号进行低噪声的双向放大,系统中间的两段掺铒光纤再利用剩余的抽运功率产生自发辐射光和放大传感信号,使得整个系统能够在超长的传感距离上获得很高的信噪比。实验表明使用一只40 mW的掺铒光纤放大(EDFA)抽运源、一只170 mW的拉曼抽运源和一只2 W的拉曼抽运源,可以使整个系统的传感距离达到100km,并且传感系统的光纤布拉格光栅反射信号均能获得超过57 dB的优良信噪比,从而实现在超长距离上的光纤布拉格光栅传感。     

光纤光栅传感器的应用

在光纤传感领域，光纤光栅传感技术是十多年来发展最为迅速的技术之一，传感系统本身和应用领域均有了很大发展．文章介绍了光纤光栅的结构、性能以及传感的原理，回顾了光纤光栅传感器在地球动力学、航天器及船舶航运、民用工程结构、电力工业、医学、和化学传感中的应用．     

一种有源型光纤水听器原理与实验分析

分析了一种有源型光纤水听器的水声传感原理,在一段掺铒光纤中写入具有π相移的光纤光栅构成光纤激光器,水声压力作用在激光器上引起激光波长的移位,采用干涉法检测出波长移位引起的相位变化即得到声压的信息.水声探测实验表明,有源型光纤水听器的声压灵敏度为-166.5 dB(参考值1 rad/μPa).将不同工作波长的四元光纤水听器串接于一根光纤内组成水听器阵列,使用带通波分复用器将阵列发出的激光分离至各独立通道后检测出相应的声压信号,测得水听器之间的级串扰小于-60 dB,且单元水听器水声响应的动态范围不受影响.     

侧面压迫式及端面拉伸式增敏光纤光栅水声传感器

研究了采用侧面压迫式增敏和端面拉伸式增敏的无源光纤光栅水声传感器。采用灌注和弹性片端面增敏两种方案分别对光纤光栅传感器进行增敏。研究结果表明灌注方案谐振频率过低(300Hz),高频灵敏度过低(小于-205dB),且制作工艺要求比较复杂;弹性片端面增敏方案采用铍铜片进行增敏,在100～1000Hz频率范围内灵敏度为(-175±2)dB。对端面增敏传感器进行了封装,并应用于水声的检测实验。实验表明,该传感器在灵敏度及灵敏度频响指标上已经可以满足应用要求。     

具有有源闭合腔的光纤光栅传感系统地址查询技术

基于熔融拉锥技术研制的3 dB宽带耦合器的光纤环形镜的工作原理,提出了一种新型的具有有源闭合腔装置的光纤光栅传感系统。在用作闭合共振腔端镜的环形镜中写入十个波分复用光纤光栅传感元,利用共振腔中接入的法布里-珀罗滤波器,通过控制电压对传感光栅的波长扫描,实现对传感地址的查询。用非平衡的迈克耳孙扫描干涉仪将传感光栅的波长漂移信息变为相移信息,实现传感信号的解调。系统传感灵敏度的实验值为1.5835°/10-6ε,与理论值(1.6662°/10-6ε)基本吻合。     

基于时分复用和窄波长扫描激光的长距离光纤布喇格光栅传感系统

提出了一种通过提高长距离光纤布喇格光栅传感系统容量,从而实现多传感点参量测量的新方法.采用时分复用、窄波长范围扫描激光方式,将多个中心波长相近的低反射率光纤布喇格光栅放置于系统的不同位置,构成准分布式光纤传感系统,实现了多个传感点参量的同时测量.同时提出了采用掺铒光纤和喇曼混合放大方法来延长传感距离.在系统的中间加入一个喇曼泵浦进行喇曼放大以此补偿光纤布喇格光栅反射的信号,系统末端的掺铒光纤利用前面喇曼泵浦剩余的泵浦功率产生自发辐射光并放大传感信号,使得整个系统的传感距离延长.实验证实：将三只中心波长均在1 580 nm附近,反射率均小于4%的光纤布喇格光栅,分别放置在系统的不同位置,在200 km处获得了15 dB的信噪比,反射信号明显|并且在200 km处的静态应变和温度实验中,线性度均达到了0.999以上.     

具有温度自校准功能的光纤折射率传感器

提出一种具有温度自校准功能的光纤折射率（RI）传感器,传感头结构由2段很短的多模光纤（MMF）之间夹熔一段对折射率不敏感的光纤布拉格光栅（FBG）构成,传感头总长度为14 mm,FBG可以为折射率测量提供良好的温度校准功能。实验结果证明,该传感器的折射率灵敏度为126 nm。其干涉光谱共振波长的温度灵敏度为35.09 pm/℃,用于温度校准的FBG的温度灵敏度为11.14 pm/℃。相比于普通的折射率传感器,这种具有温度自校准功能的折射率传感器具有良好的实用前景。     

光纤光栅与受激布里渊信号的耦合特性

近年来,光纤布拉格光栅传感器与全分布式光纤传感器的融合技术受到了广泛关注,然而光纤布拉格光栅与布里渊信号之间的耦合特性鲜有报道。本文研究了光栅类型、波长、反射率及光纤的光致折射率对受激布里渊信号的影响规律,并探讨了空间分辨率对光纤布拉格光栅定位功能的影响。实验结果表明,在布里渊光时域分析系统中,光纤布拉格光栅处有尖锐的反射峰,而啁啾光栅、长周期光栅及光致折射率变化的光纤处均未出现尖锐的反射峰;光纤布拉格光栅反射率与受激布里渊散射功率谱无关;当光纤布拉格光栅的波长接近1 550 nm时,对受激布里渊频移测量的影响最大;在8 m的长度范围内,光纤布拉格光栅的定位误差约为4 cm,并且与空间分辨率无关。     

光纤光栅传感器阵列有源时域地址查询技术

报道了一种基于环形腔光纤激光器和1×4模拟电子开关的具备实时监测功能的光纤光栅传感网络查询技术,利用级联的波分复用光栅串充当环形腔光纤激光器端镜,借助可调法布里珀罗滤波器对反射的信号光进行扫描,调整光路结构并增加抽运光强度使信号光得到足够的增益,则可获得各传感元工作波长的激光脉冲,且依时序输出。又引入1×4模拟电子开关,将转换为电信号的激光输出按时序分配至4个输出信道。结合非平衡扫描干涉解调技术,实现了对4光栅传感阵列的查询解调。1555 nm波长时系统传感灵敏度的实验值为1.630°/με,与理论值1.674°/με基本吻合。     

光纤光栅传感信号解调技术研究进展

光纤光栅传感器是一种新型传感器,有着非常广泛的应用前景。限制光纤光栅传感器大量实际应用的主要障碍是传感信号解调,因而,光纤光栅传感信号解调是光纤光栅传感器应用的关键技术之一。本文对现有已报道的光纤光栅传感信号的解调方法进行综述,并归类为:边缘滤波法、匹配滤波法、可调谐滤波法、光源波长可调谐扫描法、射频探测法、光栅啁啾法、CCD分光仪法、干涉法。对各种方法的原理及相关改进方法进行了阐述,并对其优缺点做了比较分析,最后,对光纤光栅传感信号的解调技术发展进行了展望。     

基于光栅透射光斯托克斯参量的实时压力传感方法及性能优化

提出了基于光纤光栅透射光斯托克斯参量测量的新型实时压力传感方法。深入分析了透射光第一斯托克斯参量和压力所致线双折射之间的单调变化关系。分析表明,入射线偏振光入射角度以及相应测量波长点的选择对系统灵敏度、线性度及动态范围有重要影响。利用光纤光栅和高速在线检偏器搭建了实时压力测量系统,实验数据验证了压力和透射光第一斯托克斯参量之间的单调变化关系,证明了此方法的可行性。最后对实验误差和系统性能进行了分析并提出了改进方案。     

A linearity interrogation technique with enlarged dynamic range for fiber Bragg grating sensing

An exact linearity interrogation technique with enlarged dynamic range for fiber Bragg grating (FBG) sensor has been analyzed theoretically and demonstrated experimentally. The technique bases on two matched FBGs for receiving the reflected signal from the sensor FBG and two photodiodes (PDs) for collecting the reflected signal from the two receiver FBGs. The linear expression between the nature logarithm of the output ratio of the two PDs and Bragg wavelength of the sensor FBG is obtained on the condition that the bandwidths of the two receiver FBGs being equal to each other. The wavelength of the sensor FBG can be interrogated simply and accurately by the linearity technique according to the expression. In addition, a new tunable paralleled matched gratings interrogation scheme is proposed. The interrogation range can be enlarged and multiple FBG sensors can be interrogated simultaneously with the tunable interrogation scheme.     

温度不敏感光纤光栅压强传感器

提出了一种新颖的高灵敏度温度不敏感光纤光栅压强传感器。该传感器主要由开口环传感机构和铝箔管组成，根据光纤布拉格光栅带宽调谐原理，首次采用开口环机构和利用带宽编码技术，实现了温度不敏感压强感测。实验结果表明：该传感器在低压范围内具有很高的压强传感灵敏度系数，可达2.50×103nm/MPa，实验结果与理论分析基本相符。通过选择不同材料的开口环和铝箔管的材料以及改变其结构参数，可灵活设计并调节压强传感灵敏度系数及压强感测范围。     

On the possible use of optical fiber Bragg gratings as strain sensors for geodynamical monitoring

Optical fiber sensors can be used to measure many different parameters including strain, temperature, pressure, displacement, electrical field, refractive index, rotation, position and vibrations. Among a variety of fiber sensors, fiber Bragg gratings (FBG) have numerous advantages over other optical fiber sensors. One of the major advantages of this type of sensors is attributed to wavelength-encoded information given by the Bragg grating. Since the wavelength is an absolute parameter, signal from FBG may be processed such that its information remains immune to power fluctuations along the optical path. This inherent characteristic makes the FBG sensors very attractive for application in harsh environments, “smart structures” and on-site measurements.This paper reviews the achievements about the FBG as a strain and temperature sensor and describes the potential applications of FBG sensors for applications in the field of geophysics and its expected development in the near future. The applications could include: rock deformation, fiber-optic geophone, optical based seismograph, vertical seismic profiling and structural monitoring of civil structures. Different techniques to detect strains and various applications will be reviewed and discussed. The problem of temperature–strain cross sensitivity, that is particularly difficult to eliminate, is addressed and approaches to overcome it are discussed.     

基于F-P腔和FBG的强度调制型光纤液位传感器

设计了一种用于液位测量的光纤F-P(Fabry-Perot)传感器,并从传感头的设计制作出发,讨论了提高传感器输出信号对比度的方法;测量系统采用宽带光源,解调时经FBG(Fiber Bragg Grating)反射和透射得到传感信号和参考信号,对两路光强信号进行联合处理,补偿了光源功率波动和光路损耗变化引起的不良影响,消除了强度调制型传感器的固有缺点,此方法具有结构简单、成本低的优点;该系统可进行连续测量,测量范围为0到200kPa,相当于测量水深0到20m,其分辨力小于1cm(水面高度变化),特别适合对易燃易爆的环境中的油库液位进行测量。     

岩层变形检测的光纤光栅多点传感理论与工程应用

为了监测松散地层沉降变形,提出了一种用于钻孔中植入式光纤Bragg光栅传感器(FBG)的结构和传感网络系统.基于室内实验结果,给出了用于岩层变形检测的传感光栅波长带宽为6 nm,分析了多点传感信号分辨因子,山光源带宽决定的测试系统最大实际复用能力为6个传感器.设计并实现了一个由18个光纤光栅组成的具有特色的光纤Bragg光栅波分复用/空分复用混合阵列.工程实践表明,光纤光栅传感系统采用双同路布置.可提高系统下放后光纤光栅传感器的成活率.     

An interferometric phase shift fiber Bragg grating sensing system with greatly reduced background phase noise

We presented an interferometric phase shift fiber Bragg grating(FBG) sensor, which inherited the advantages of FBG sensors, and, at the same time, the greatly reduced full-width-at-half-maximum bandwidth brought longer coherent length, higher sensitivity, and lower phase noise. Experiments show that at least a 7 dB reduction of phase noise can be achieved compared to FBG sensors interrogated by interferometer with the same optical path difference.