用对氨基苯酚改性的碳纳米管糊电极同时测定羟胺和苯酚(英文)

A carbon paste electrode that was chemically modified with multiwall carbon nanotubes and p-aminophenol was used as a selective electrochemical sensor for the simultaneous detection of hydroxylamine (HX) and phenol. Cyclic voltammetry, double potential-step chronoamperometry, square wave voltammetry (SWV), and electrochemical impedance spectroscopy were used to investigate the use of p-aminophenol in the carbon nanotubes paste matrixes as a mediator for the electrocatalytic oxidation of HX and phenol in aqueous solution. The coefficient of electron transfer and catalytic reaction rate constant were determined using the electrochemical methods. Under optimized conditions, the electrocatalytic oxidation current peaks for HX and phenol increased linearly with concentration in the range of 0.5-180.0 and 10.0-650.0 μmol/L for HX and phenol, respectively. The detection limits for HX and phenol were 0.15 and 7.1 μmol/L, respectively. The anodic potential peaks of HX and phenol were separated by 0.65 V in SWV. Because of good selectivity and sensitivity, the present method provides a simple method for the selective detection of HX and phenol in practical samples such as water samples.     

Direct electrocatalytic reduction of p-nitrophenol at room temperature ionic liquid modified electrode

Direct electrochemical reduction ofp-nitrophenol （PNP） was investigated on a room temperature ionic liquid N-butylpyridinium hexafluorophosphate （BPPF6） modified carbon paste electrode （CILE）. The cathodic peak potential was positively shifted and the peak currents were increased compared to that obtained on traditional carbon paste electrode （CPE）. The results indicated that the presence of ionic liquid BPPF6 on the electrode surface showed excellent catalytic ability to the electrochemical reduction of PNP. The electrochemical behaviors of PNP on the CILE were investigated by cyclic voltammetry and the conditions such as the scan rate, the buffer pH, the substrate concentration were optimized. The electrochemical parameters were further calculated with the results of the electron transfer number （n）, the charge-transfer coefficient （α） and the surface concentration （Гr） as 1.76, 0.37 and 2.47 × 10^-9 mol/cm^2, respectively, for the selected reductive peak. The results indicated that PNP showed an irreversible adsorption-controlled electrode process on the CILE.     

方波伏安法测定新型修饰多壁碳纳米管糊电极对肼的电催化氧化(英文)

The application of p-aminophenol as a suitable mediator, as a sensitive and selective voltammetric sensor for the determination of hydrazine using square wave voltammetric method were described. The modified multiwall carbon nanotubes paste electrode exhibited a good electrocatalytic activity for the oxidation of hydrazine at pH = 7.0. The catalytic oxidation peak currents showed a linear dependence of the peaks current to the hydrazine concentrations in the range of 0.5–175 μmol/L with a correlation coefficient of 0.9975. The detection limit (S/N = 3) was estimated to be 0.3 μmol/L of hydrazine. The relative standard deviations for 0.7 and 5.0 μmol/L hydrazine were 1.7 and 1.1%, respectively. The modified electrode showed good sensitivity and selectivity. The diffusion coefficient (D = 9.5 × 10–4 cm2/s) and the kinetic parameters such as the electron transfer coefficient (α = 0.7) of hydrazine at the surface of the modified electrode were determined using electrochemical approaches. The electrode was successfully applied for the determination of hydrazine in real samples with satisfactory results.     

在3,4-二羟基肉桂酸介质中以多壁碳纳米管为传感器电催化检测L-半胱氨酸(英文)

A highly sensitive electrochemical sensor was prepared for the determination of L-cysteine using a modified multiwall carbon nanotubes paste electrode in the presence of 3,4-dihydroxycinnamic acid(3,4-DHCA) as a mediator, based on an electrocatalytic process. The results indicate that the electrode is electrocatalytically efficient for the oxidation of L-cysteine in the presence of 3,4-DHCA. The interaction between the mediator and L-cysteine can be used for its sensitive and selective determination. Using chronoamperometry, the catalytic reaction rate constant was calculated to be 2.37 × 102 mol–1 L s–1. The catalytic peak current was linearly dependent on the L-cysteine concentration in the range of 0.4–115 μmol/L. The detection limit obtained by linear sweep voltammetry was 0.25 μmol/L. Finally, the modified electrode was examined as a selective, simple, and precise new electrochemical sensor for the determination of L-cysteine in real samples.     

苯甲酰二茂铁修饰碳纳米管糊电极电催化测量蛋氨酸浓度(英文)

A benzoylferrocene modified multi‐wall carbon nanotube paste electrode for the measurement of methionine (MET) concentration is described. MET electrochemical response characteristics of the modified electrode in a phosphate buffer solution of pH 7.0 were investigated by cyclic voltammetry, square wave voltammetry, and chronoamperometry. Under optimized conditions, the square wave voltammetric peak current of MET increased linearly with MET concentration in the range of 1.0×107 to 2.0×104 mol/L. The detection limit was 58.0 nmol/L MET. The diffusion coefficient (D=5.62×106cm2/s) and electron transfer coefficient (α=0.4) for MET oxidation were also determined. The sensor was successfully applied for the measurement of MET concentration in human urine.     

尿酸和叶酸存在下改性碳纳米管糊电极上多巴胺电催化氧化(英文)

A chemically modified carbon paste electrode (CPE), consisting of 2,2'-[ (1E)- (1,2- phenylenebis (azanylylidene)] bis (methanylylidene)]bis (benzene-1,4-diol) (PBD) and multiwalled carbon nano-tubes (CNTs), was used to study the electrocatalytic oxidation of dopamine using cyclic voltamme-try, chronoamperometry, and differential pulse voltammetry (DPV). First, the electrochemical be-havior of the modified electrode was investigated in buffer solution. Then the diffusion coefficient, electrocatalytic rate constant, and electron-transfer coefficient for dopamine oxidation at the sur-face of the PBD-modified CNT paste electrode were determined using electrochemical approaches. It was found that under optimum conditions (pH = 7.0), the oxidation of dopamine at the surface of such an electrode occurred at about 200 mV, lower than that of an unmodified CPE. DPV of dopa-mine at the modified electrode exhibited two linear dynamic ranges, with a detection limit of 1.0 μmol/L. Finally, DPV was used successfully for the simultaneous determination of dopamine, uric acid, and folic acid at the modified electrode, and detection limits of 1.0, 1.2, and 2.7 μmol/L were obtained for dopamine, uric acid, and folic acid, respectively. This method was also used for the determination of dopamine in a pharmaceutical preparation using the standard addition method.     

pharmaceutical and biological samples using modified multiwall carbon nanotubes paste electrode

A carbon paste electrode(CPE) chemically modified with multiwall carbon nanotubes and ferrocene(FC) was used as a selective electrochemical sensor for the simultaneous determination of trace amounts of cysteamine(CA) and folic acid(FA).This modified electrode showed very efficient electrocatalytic activity for the anodic oxidation of CA.The peak current of differential pulse voltammograms of CA and FA increased linearly with their concentration in the ranges of 0.7-200μmol/L CA and 5.0- 700μmol/L FA.The detection limits for CA and FA were 0.3μmol/L and 2.0μmoI/L,respectively.The diffusion coefficient(D) and transfer coefficient(α) of CA were also determined.These conditions are sufficient to allow determination of CA and FA both individually and simultaneously.     

用聚(L-蛋氨酸)/纳米金修饰玻碳电极同时灵敏检测多巴胺和尿酸(英文)

A novel electrochemical sensor was fabricated by electrodeposition of gold nanoparticles on a poly(L-methionine)(PMT)-modified glassy carbon electrode(GCE) to form a nano-Au/PMT composite-modified GCE(nano-Au/PMT/GCE).Scanning electron microscopy and electrochemical techniques were used to characterize the composite electrode.The modified electrode exhibited considerable electrocatalytic activity towards the oxidation of dopamine(DA) and uric acid(UA) in phosphate buffer solution(pH = 7.00).Differential pulse voltammetry revealed that the electrocatalytic oxidation currents of DA and UA were linearly related to concentration over the range of 5.0 ×10–8 to 10–6 mol/L for DA and 7.0 × 10–8 to 10–6 mol/L for UA.The detection limits were 3.7 × 10–8mol/L for DA and 4.5 × 10–8 mol/L for UA at a signal-to-noise ratio of 3.According to our experimental results,nano-Au/PMT/GCE can be used as a sensitive and selective sensor for simultaneous determination of DA and UA.     

基于纳米结构的电化学传感器用于伏安法测定苄丝肼、尿酸和叶酸(英文)

A carbon paste electrode modified with carbon nanotubes and ferrocene was fabricated.An electrochemical study of the modified electrode and an investigation into its efficiency for the electrocatalytic oxidation of benserazide,uric acid and folic acid were undertaken.The electrode was also used to study the electrocatalytic oxidation of benserazide using cyclic voltammetry,chronoamperometry,and square wave voltammetry(SWV).We found that the oxidation of benserazide at the surface of the modified electrode occurs at a potential about 285 mV lower than that of unmodified carbon paste electrode.SWV gave a linear dynamic range from 8.0×10-7 to 7.0×10 4 mol/L.The detection limit was 1.0×10-7 mol/L for benserazide.This modified electrode was used for the determination of benserazide,uric acid,and folic acid in an urine sample.     

以方沸石负载Ni(Ⅱ)催化剂修饰的电极电氧化甲醇(英文)

There is a high overvoltage in the oxidation of methanol in fuel cells,and so modified electrodes are used to decrease it.A modified electrode that used Ni(II) loaded analcime zeolite to catalyze the electrooxidation of methanol in alkaline solution was proposed.Analcime zeolite was synthesized by hydrothermal synthesis,and Ni(II) ions were incorporated into the analcime structure,which was then mixed with carbon paste to prepare modified electrode.The electrocatalytic oxidation of methanol on the surface of the modified electrode in alkaline solution was investigated by cyclic voltammetry and chronoamperometry.The effects of the scan rate of the potential,concentration of methanol,and amount of zeolite were investigated.The rate constant for the catalytic reaction of methanol was 6 × 103 cm3 mol-1 s-1 from measurements using chronoamperometry.The proposed electrode significantly improved the electron transfer rate and decreased the overpotential for methanol oxidation.     

Determination of captopril in patient human urine using ferrocenemonocarboxylic acid modified carbon nanotubes paste electrode

<正>In this work,we describe a new strategy for the electrochemical determination of captopril(CA) using ferrocenemonocarboxylic acid as a mediator and multiwall carbon nanotubes as sensors in aqueous solution at pH 7.0.The diffusion coefficient(D),and the kinetic parameters such as electron transfer coefficient(α).and heterogeneous rate constant(k_h),for CA were also determined using electrochemical approaches.Under the optimized conditions,the electrocatalytic oxidation peak current of captopril showed two linear dynamic ranges with a detection limit of 0.3×10~(-6) mol L~(-1) captopril.The linear calibration range was 0.8×10~(-6) to 65×10~(-6) mol L~(-1) using cyclic voltammetry.Finally,this modified electrode was also examined as a selective,simple and precise new electrochemical sensor for the determination of captopril in real samples such as drug and patient human urine.     

银纳米颗粒的合成及用于抗癌药氟他胺的电化学检测（英文）

Ag nanoparticles were synthesized on the surface of a glassy carbon electrode modified with p‐tert‐butylcalix[4]arene and p‐tert‐butylcalix[6]arene by the deposition of Ag+ at an open circuit potential followed by the electrochemical reduction of the Ag+.The presence of the calixarene layer on the electrode surface controlled the particle size and prevented agglomeration.Cyclic voltam‐metry showed that the Ag nanoparticles on the modified glassy carbon electrode had good catalytic ability for the reduction of flutamide.The effects of calixarene concentration,potential applied for the reduction of Ag+,number of calixarene layers,and p H value on the electrocatalytic activity of the Ag nanoparticles were investigated.The modified electrode had a linear range in differential pulse voltammetry of 10-1000 μmol/L with a detection limit of 9.33 μmol/L for flutamide at an S/N = 3.The method was applied to the detection of flutamide in practical samples.     

Electrochemical Behavior of Mitoxantrone and Its Determination at a Pt／C Implanted Modified Microelectrode

In a 0.02 mol/L Na2HPO4-KH2PO4(PBS) buffer solution(pH=6.82), the electrochemical behavior of mitoxantrone was studied by linear-sweep voltammetry and cyclic voltammetry at a Pt/C ion implantation modified microelectrode. A sensitive reduction peak was observed. The peak potential was -0.72 V(vs.SCE), the peak current was proportional to the concentration of mitoxantrone within the ranges of 7.0×10-8-9.0×10-7 mol/L and 1.0×10-6-2.4×10-5 mol/L, with a detection limit of 4.0×10-8 mol/L. The linear correlation coefficients were 0.9994 and 0.9992, respectively. This method has been applied to the direct determination of mitoxantrone in simulated urine. The recoveries were in the range from 96.2% to 105.9%. The reduction process was a quasi-reversible one with adsorptive characteristics at the Pt/C microelectrode. The electrode reaction rate constant ks and the electron transfer coefficient α of the system were determined to be 4.5 and 0.65 s-1, respectively. The experiments showed that Pt element had surely been implanted into the surface of the carbon fiber, and the atomic Pt improved the electrocatalytic activity. The Pt/C microelectrode had a good stability and reproducibility.     

Ionic liquid modified GC electrode for the direct electrochemistry of chloroperoxidase

Chloropcroxidase （CPO） was immobilized by konjac glucomannan （KGM） on the 1-butyl-3-methyl imidazolium tetrafluoroborate [BMIM][BF4]/Nafion modified glassy carbon eloctrode. The electrochemical behaviors of the immobilized CPO were investigated by cyclic voltammetry. The results showed that CPO was successfully immobilized on the GCE and underwent fast direct electron transfer reactions with the formal potential at -0.3 V vs. SCE. The modified electrode showed a good catalytic activity for elcctrocatalytical reduction of O2 and H2O2.     

Eleciroreduction of Oxygen on Pyrolytk Graphite Electrode with Adsorbed Layer of Cobalt Tetra.sulfonaied Phthalocyaninc In Acetonitrile and Dimethylformamide

The catjpdoc polarization characteristics indicate that the presence of a pre-adsorbed surface layer of CoTSPc innibits the reduction of O2 to O2- on an ordinary pyroiytic graphite electrode (OPG) in AN and DMF solution of 0. 1 mol/L, TEAP, The transfer coefficient a and the heterogeneous rate constant k for this reaction or, OPG with and without pre-adsorbed CoTSPc obtained by rotating disk electrode method were found to be fairly close to thar obtained by cyclic voltammetry. The a remains almost the same, bat the k de creases by a factor of 2-5 with CoTSPc as compared with OPG alone. The possible reason is that the adsorbed CoTSPc as an anion renders the effective potential diffaence less negative, which thus lowers the rase of O2 reduction.     

银掺杂聚(2-氨基二苯胺)修饰碳糊电极作为一种简单有效的电催化剂用于甲醛氧化（英文）

This work describes the promising activity of silver nanoparticles on the surface of a poly(2‐amino diphenylamine) modified carbon paste electrode(CPE) towards formaldehyde oxidation. Electro‐deposition of the conducting polymer film on the CPE was carried out using consecutive cyclic voltammetry in an aqueous solution of 2‐aminodiphenylamine and HCl. Nitrogen groups in the polymer backbone had a Ag ion accumulating effect, allowing Ag nanoparticles to be electrochemi‐cally deposited on the surface of the electrode. The electrochemical and morphological characteris‐tics of the modified electrode were investigated. The electro‐oxidation of formaldehyde on the sur‐face of electrode was studied using cyclic voltammetry and chronoamperometry in aqueous solu‐tion of 0.1 mol/L Na OH. The electro‐oxidation onset potential was found to be around-0.4 V, which is unique in the literature. The effect of different concentrations of formaldehyde on the electrocat‐alytic activity of the modified electrode was investigated. Finally, the diffusion coefficient of formal‐dehyde in alkaline media was calculated to be 0.47 × 10–6 cm2/s using chronoamperometry.     

以3,4-二羟基肉桂酸为介质的多壁碳纳米管糊电极用于检测药物和尿液样品中的谷胱甘肽(英文)

A sensitive and selective electrochemical sensor for the determination of glutathione(GSH) was developed using a modified multiwall carbon nanotube paste electrode with 3,4 dihydroxy cinnamic acid as a mediator.This modified electrode showed very high electrocatalytic activity for the anodic oxidation of GSH.Under the optimized conditions,the electrocatalytic peak current showed a linear relationship with GSH concentration in the range of 0.5-400.0 μmol/L with a detection limit of 0.1 μmol/L GSH.The relative standard deviations for seven successive assays of 5.0 and 25.0 μmol/L GSH were 2.2% and 2.7%,respectively.The modified electrode was used for the determination of GSH compounds in real urine samples.     

对乙酞氨基酚和色氨酸存在下采用改进的碳纳米管糊电极伏安法测定抗坏血酸(英文)

A carbon paste electrode (CPE) modified with carbon nanotubes and 5‐amino‐3’,4’‐dimethyl‐ bi‐ phenyl‐2‐ol (5ADB) is prepared. Under the optimum pH of 7.0, the oxidation of ascorbic acid (AA) on the modified CPE occurs at a potential about 280 mV less positive than that on the unmodified CPE. Some kinetic and thermodynamic parameters for electrocatalytic oxidation of AA, including electron transfer coefficient (α = 0.58) and diffusion coefficient (D = 2.2 × 10-6 cm2/s), are also determined. AA, acetaminophen (AC), and tryptophan (TRP) were detected simultaneously using the modified CPE. The peak potentials recorded using the modified CPE in phosphate‐buffered solution at pH 7.0 were 265, 465, and 780 mV for AA, AC, and TRP, respectively. The modified CPE was successfully used to determine the concentrations of AA, AC, and TRP in real samples.     

在色氨酸存在下利用多壁碳纳米管糊电极和萘酚介质构成的伏安传感器测定N-乙酰半胱氨酸(英文)

A multiwall carbon nanotube modified electrode prepared by incorporating multiwall carbon nanotubes in the electrode of a sensor and naphthol green as a homogeneous mediator was used as a voltammetric sensor for the determination of N‐actylcysteine(N‐AC) in the presence of trypto-phan(Trp). The voltammograms of differential pulse voltammetry of N‐AC in a mixture with Trp were separated from each other by a potential difference of 200 mV, which allowed the determina-tion of both N‐AC and Trp simultaneously. Under the optimum conditions, the electrocatalytic cur-rents increased linearly with N‐AC concentration in the range of 0.25–400 μmol/L(two linear seg-ments with different slopes). The detection limit for N‐AC was 0.08 μmol/L. The kinetic parameters of the system were determined using electrochemical methods. The method was applied for the determination of N‐AC in drug and urine samples.     

Electrochemical behavior of C-(60) modified electrode in aqueous solutions

The construction of adsorptive type C60 modified electrode and its electrochemical reduction and oxidation behavior in aqueous solutions are described in this report. Four pairs of one-electron transfer reduction and oxidation cyclic voltammetry is obtained in aqueous solution containing 30% CH3CN and 2% (C2H5)4NOH. It is reported in this paper that the C60 modified electrode also catalyzes the electrochemical reduction of dissolved oxygen in 40% DMF and 2% (C2H5)4NOH aqueous solution and this might open a new field for the potential applications of C60 in electrochemistry and electroaualytical chemistry.