偏振模色散对非线性光纤环镜微波光子开关的影响及其补偿

建立了考虑PMD在内的NOLM微波光子开关光波传输方程,给出了基于耦合非线性薛定谔方程的分步傅里叶法,三维庞加莱球理论和琼斯传输矩阵法的数值分析模型.仿真获得在光子开关中微波直接强度调制光载波的传输过程,以及在不同调制带宽下一阶和二阶PMD对光波信号和NOLM功率传输函数的影响.指出PMD造成NOLM开关性能钝化和消光比严重恶化,并引起信号信噪比下降和旁瓣泄漏.当调制带宽大于40GHz时,二阶PMD的影响比一阶PMD更加严重.最后讨论了NOLM中的PMD补偿问题.     

非线性光纤环镜在受激布里渊散射慢光级联系统中的可行性研究

基于非线性光纤环镜(NOLM)的脉冲压缩特性,分析了NOLM在基于受激布里渊散射(SBS)慢光级联系统中对延迟脉冲的影响.利用环形结构来模拟多次级联,有效地降低了系统的复杂度,得到了在不同抽运光功率和级联次数下脉冲的延迟输出特性.理论分析表明,NOLM可以有效地抑制SBS慢光级联系统中延迟脉冲的展宽,抽运光功率决定了展宽因子的变化趋势及最终稳定值的大小,展宽因子在级联4次时趋于稳定值,恰当选取抽运光功率可实现脉冲的零展宽延迟;改变抽运光功率和级联次数可以实现延迟量的连续可调,且延迟量理论上不受限制;增大抽 关键词： 慢光 脉冲压缩 非线性光纤环镜 受激布里渊散射     

具有高阶耦合色散系数三芯光纤耦合器非线性光开关特性的研究

利用两种方法研究了高速光脉冲在具有交叉相位调制的等边三角形排列结构的非线性三芯光纤耦合器中传输和开关特性.首先利用变分原理得到三纤芯中传输转移系数随距离变化的方程,然后利用分裂步长傅里叶方法求得了光脉冲的数值解.变分法和数值模拟的结果表明：当一阶模间色散系数较小时,光脉冲仍能在三芯之间周期性耦合传输,并且表现出良好的开关特性,但是随着一阶模间色散系数的增大,脉冲耦合传输的周期性和陡峭的开关特性都遭到破坏,光脉冲在传输中发生分裂;二阶耦合色散系数和初始啁啾都能使光脉冲传输时的耦合长度变短、光脉冲在三纤芯之间 关键词： 三芯光纤耦合器 模间色散系数 耦合长度 开关阈值功率     

色散补偿及高阶孤子压缩啁啾光脉冲的理论与实验研究

利用半导体激光器的单模速率方程及超短光脉冲在光纤中传输的非线性薛定谔(NLS)方程，从理论及实验上研究了增益开关DFB半导体激光器出射的啁啾光脉冲在色散补偿光纤(DCF)及色散位移光纤(DSF)中的压缩过程与规律.实验上，从1.55μm增益开关DFB半导体激光器出射的重复频率为2.5GHz、脉冲宽度为53.8ps的光脉冲经色散补偿光纤压缩至12ps,而后利用色散位移光纤中的高阶孤子压缩效应将脉冲压缩至2.5ps.改变色散位移光纤参数及入射光功率后获得最窄光脉冲宽度为2.1ps.理论与实验结果符合. 关键词：     

利用非线性光纤环镜160Gb/s到10Gb/s解时分复用

研究了160 Gb/s光时分复用(OTDM)系统的解复用技术.针对160 Gb/s速率的特点,对高非线性光纤(HNLF)的光纤环镜(NOLM)特性及解复用进行了数值仿真.计算了低信号光时间抖动下解复用误码特性对时钟与信号的走离及时钟功率的依赖关系.计算了三种走离值消光比随时钟功率增加的变化趋势并给出:存在一个能获得最大的解复用窗口消光比、并能降低相邻信道串扰的合适的时钟功率范围.利用自制的基于电吸收调制器和压缩技术的超短光脉冲源建立了160 Gb/s OTDM实验系统,测量了不同信号光功率下NOLM的消光比,它基本不随信号增大而变化,在信号功率为7.3 dBm时仍大于23 dB.利用上述装置实现了无误码的160 Gb/s到10 Gb/s全光解复用.     

基于可调光延迟线的光子学微波频率测量

提出了一种基于可调光延迟线的光子学微波频率测量方法.经同一微波信号调制的两个不同波长光载波在经过一段可调色散介质传输后,解调输出两路具有不同相位的微波信号,得到的相干微波功率随着色散量的改变出现周期性变化,由此周期可得到输入微波频率值.采用由8个磁光开关和1.6 km单模光纤构成的7-bit光纤延迟线实现色散量的调节....     

反常色散材料光子晶体中光输运的光学控制

研究了光抽运对由铯原子蒸气构成的光子晶体的影响.研究发现,利用较弱光强的线抽运光即可显著地改变这种反常色散光子晶体的透射率.而利用圆偏振光抽运可以进一步降低抽运光的阈值,并在反常色散光子晶体中获得极大的法拉第旋转.反常色散光子晶体的这些特性为光控光开关的研究和制作提供了一条新途径.     

基于SOA和NOLM的光脉冲放大与压缩的设计模型

设计了一种基于半导体光放大器(SOA)和非线性光学环镜(NOLM)的光脉冲放大与压缩的模型。数值研究结果表明:在NOLM中,当调节合适的控制脉冲的输入和初始时延时,具有较低峰值功率、宽度为几十皮秒的高斯信号脉冲经此模型放大压缩后,可以得到脉冲峰值增益高、脉冲宽度窄以及基本无基座的高质量超短信号光脉冲。     

交叉相位调制对非线性光纤环镜中光脉冲传输的影响

基于耦合非线性薛定谔方程,采用分步傅里叶方法分析了在单波长信道和WDM（波分复用）4波长信道中XPM（交叉相位调制）对高速NOLM（非线性光纤环镜）光开关中脉冲传输的影响.数值计算表明：XPM造成NOLM中信号脉冲串扰与畸变,并造成NOLM开关性能的下降.WDM系统NOLM光纤环中的同向传播的各波长之间的XPM串扰比相向脉冲之间的XPM效应的影响更大,并且波长越短输出功率越低,中间信道受XPM的影响所导致的脉座现象和走离效应比两侧波长信道严重.     

16×10Gb/s啁啾光纤光栅色散补偿系统性能研究

运用啁啾光纤光栅法对在G.652光纤传输的16×10 Gb/s信号实现色散补偿数值模拟和研究,分析了入纤光功率、色散斜率以及啁啾光纤光栅色散补偿带宽对系统误码率的影响,结论是:入纤光功率在8～16 dBm之间时系统的性能较好;啁啾光纤光栅的色散补偿带宽对系统的影响较大;光纤的色散斜率对系统误码率有一定的影响.     

Analyzing the Switching Characteristics of a NOLM Demultiplexer with on Analytic and Numerical Methods

The switching characteristics of a NOLM demultiplexer are investigated by using an analytic and numerical methods. The results reveal that the switching characteristics of a NOLM demultiplexer depend on parameters such as the power coupling ratio of the coupler,the peak power of control pulses,the walk-off and the initial time delay between signal pulses and control pulses,etc. The efficiency of NOLM is dependent on the peak power of control pulses. However,the switching window profile begins to oscillate as the power exceeds a critical value and this will be detrimental to the demultiplexed signals. The signal-control pulse walk-off can broaden the switching window of NOLM,make the window profile deviate from its central position,and decrease its switching efficiency.     

Analyzing the Switching Characteristics of a NOLM Demultiplexer with on Analytic and Numrical Methods

1IntroduCtionAllopticalswitchesarekeycOrnpoentsinfuturehigh-speedOPticaltimediVisi0nmultiPleking(0TDM),yst.ms[i].Asasort0fall-OPticalsWtchingdevices,nonllnear0Pticalboharrors(NOLMs)areverysultablef0rall-0PticaldemultiplexinginultrahighsPeedOTDMsystemsbecause0ftheirsimPleconfiguratdri,stableandreliableperformance,andultrafastresP0ndingspeed['J.HOWever,asN0LMutilizestheinherentnonlinearity(crossphasemodulation:XPM)0ffibertoperf0rmswttching,weaknonlineareffects0ffibercausethatl0nger…     

Demonstration of a 16×10-Gb/s OTDM system

A 16×10-Gb/s optical time-division-multiplexing (OTDM) system was demonstrated experimentally with a well-designed ultrashort pulse source based on an electro-absorption modulator (EAM) and nonlinear fiber compressor. The obtained 10-GHz stable and pedestal-free pulse train has 2-ps width, high extinction ratio, and low timing jitter. An ultrafast demultiplexer based on a nonlinear optical loop mirror (NOLM) including a commercially available highly nonlinear fiber (HNLF) is employed to demultiplex data signal from 160 to 10 Gb/s. A back-to-back error-free demultiplexing experiment is carried out to verify the system performance.     

Asymmetric Nonlinear Optical Loop Mirror for All Optical Clock Extraction in Self-clocked Optical Transparent OTDM Network

１ＩｎｔｒｏｄｕｃｔｉｏｎＡｓａｅｆｅｃｔｉｖｅｗａｙｔｏｔａｋｅｆｕｌａｄｖａｎｔａｇｅｓｏｆｔｈｅｂａｎｄｗｉｄｔｈｏｆｔｈｅｆｉｂｅｒ,ｏｐｔｉｃａｌｔｉｍｅｄｉｖｉｓｉｏｎｍｕｌｔｉｐｌｅｘｉｎｇ（ＯＴＤＭ）ｔｅｃｈｎｏｌｏｇｙｈａｓｂｅｎｗ...     

相移干涉计量中相移器的原路相干相位检测标定

A new all-optical clock extraction scheme based on an asymmetric nonlinear optical loop mirror (NOLM) is proposed and demonstrated experimentally. The proposed scheme can operate at a relatively low switching power (only 0.3 Pπ is required for the clock pulse, where Pπ means the required switching power for the maximum switching in the asymmetric NOLM) and a relatively low input clock to data ratio (2～2.5). The proposed scheme is promising for clock extraction in the future ultrahigh-speed self-clocked OTDM network.     

Bit-error-rate analysis for a 100-Gbit/s nonlinear optical loop mirror demultiplexer employing soliton control and signal pulses

On the basis of a previously derived mathematical model, the power penalty associated with a nonlinear optical loop mirror (NOLM) demultiplexer was calculated, with timing jitter noise, bit-to-bit cross talk, and channel cross talk taken into consideration. Simulation results show that a 3-dBm improvement in the receiver sensitivity at a bit error rate of 10(-9) can be achieved by choice of the appropriate walk-off time between the control and the signal pulses within the NOLM demultiplexer.     

Optical pulse shaping at moderate power using a twisted-fibre NOLM with single output polarisation selection

We demonstrate theoretically and experimentally that efficient signal shaping operation can be obtained at moderate power by using the transmission characteristic of a power-symmetric nonlinear optical loop mirror (NOLM) including highly twisted fibre and operating through nonlinear polarisation rotation, when the circular polarisation state orthogonal to the input polarisation is selected at the NOLM output. By adjusting the angle of the quarter-wave retarder inserted in the loop, the phase bias of the transfer characteristic can be adjusted precisely to enable proper signal shaping for moderate values of input power, remaining well below switching power. The tolerance of the procedure to deviations of the input polarisation from the ideal circular case is investigated numerically. We demonstrate experimentally the capabilities of this setup for both power equalisation and extinction ratio enhancement. Finally, we show that this setup is also useful to shape ultrashort optical pulses from the relaxation oscillations of a DFB semiconductor laser. In comparison with other NOLM-based techniques, the proposed approach allows to reduce by a factor of 8-10 the peak power required for pulse shaping, for the same fibre length and Kerr coefficient.     

输入光特性对超快非线性干涉仪开关窗口的影响

就超快非线性干涉仪(UNI)的输入光特性对其开关窗口的影响进行了数值模拟和实验研究,输入光包括控制光脉冲和探测光脉冲。在数值模拟中,调节控制光脉冲和探测光脉冲的功率及脉宽,功率越高和脉宽越窄,窗口的形状越好。在调节过程中发现控制光脉冲和探测光脉冲都存在一个最佳的功率点使窗口的形状达到最优。如果继续增大控制光脉冲功率,会使窗口的顶部倾斜,窗口形状恶化;而继续增大探测光脉冲功率,窗口的消光比开始下降。在数值模拟的基础上进行了10Gb／s的超快非线性干涉仪全光开关实验,在实验中用连续光代替探测光脉冲以观察窗口形状。通过改变控制光脉冲和连续光功率来验证它们对超快非线性干涉仪开关窗口的影响。实验表明,应选用短而强的控制光脉冲和最优功率点的连续光,这与模拟结果吻合。