Cr/MCM-41催化剂的结构特征及其纳米尺寸孔内聚乙烯的形成

合成了纯硅MCM-41,并以浸渍法在表面负载烯烃聚合催化活性中心---过渡金属元素Cr;通过对所得Cr/MCM-41样品的结构特征及Cr物种的存在形成进行XRD,低温N2吸附,FTIR,Raman,^2^9SiNMR等表征发现,Cr/MCM-41具有良好的长程有序结构、较高的比表面积及均一的孔径分布。负载于MCM-41表面的Cr物种通过与羟基的相互作用分散于载体孔道内。Cr负载量较低时,Cr物种主要以孤立态存在,随着Cr含量增加,出现聚合态的Cr物种。Cr/MCM-41的一维孔道内,不仅可进行乙烯的聚合形成聚乙烯,而且反应后MCM-41的长程结构保持不变。     

The synthesis of organo-imido complexes of Cr(IV) and Fe(III)

The reaction of p-tolylazide with (5,10,15,20- tetraphenylporphyrinato) chromium(II) (Cr(TPP)) yields the high spin chromium(IV) organo-imido complex, CH₃C₆H₄N=Cr(TPP). N,N′-ethylene- bis-(salicylideneiminato)iron(II), (Fe(salen)), however reacts with arylazides to produce iron(III) organo-imido-bridged compounds of general formula, [Fe(salen)]₂NR showing magnetic coupling between the Fe(III) centres.     

Cyano-bridged Mn(III)3M(III) (M(III) = Fe, Cr) complexes: synthesis, structure, and magnetic properties

Two cyano-bridged tetranuclear complexes composed of Mn(III) salen (salen = N,N'-ethylene bis(salicylideneiminate)) and hexacyanometalate(III) (M = Fe, Cr) in a stoichiometry of 3:1 have been selectively synthesized using {NH2(n-C12H25)2}3[M(III)(CN)6] (M(III) = Fe, Cr) starting materials: [{Mn(salen)(EtOH)}3{M(CN)6}] (M = Fe, 1; Cr, 2). Compounds 1 and 2 are isostructural with a T-shaped structure, in which [M(CN)6]3- assumes a meridional-tridentate building block to bind three [Mn(salen)(EtOH)]+ units. The strong frequency dependence and observation of hysteresis on the field dependence of the magnetization indicate that 1 is a single-molecule magnet.     

Spectroscopic approach in characterization of chromium(III), manganese(II), iron(III) and copper(II) complexes with a nitrogen donor tetradentate, 14-membered azamacrocyclic ligand

The complexes of Cr(III), Mn(II), Fe(III) and Cu(II) were synthesized with the macrocyclic ligand i.e. 2,3,9,10-tetraketo-1,4,8,11-tetraazacyclotetradecane. The ligand was prepared by the [2 + 2] condensation reaction of diethyloxalate and 1,3-diamino propane. These complexes were found to have the general composition M(L)X3 and M'(L)X2 [where M = Mn(II) and Cu(II), M' = Cr(III) and Fe(III), L = ligand (N4) and X = Cl-, NO3-, 1/2SO4(2-) and [CH3COO-]. The ligand and its transition metal complexes were characterized by the elemental analyses, molar conductance, magnetic susceptibility, mass, IR, electronic, and EPR spectral studies. On the basis of IR, electronic and EPR spectral studies an octahedral geometry has been assigned for Cr(III), Mn(II) and Fe(III) and a tetragonal geometry for Cu(II) complexes.     

Speciation of Cr(III) and Cr(VI) in environmental samples by using coprecipitation with praseodymium(III) hydroxide and determination by flame atomic absorption spectrometry

A speciation procedure has been established for the flame atomic absorption spectrometric determination of Cr(III) and Cr(VI) based on coprecipitation of Cr(III) by using praseodymium(III) hydroxide (Pr(OH)₃) precipitate. In the presented system, Cr(III) was quantitatively (>95%) recovered at the pH range of 10.0?C12.0 on Pr(III) hydroxide, while the recoveries of Cr(VI) were below 10%. The method was applied to the determination of the total chromium after reduction of Cr(VI) to Cr(III) by using hydroxylamine hydrochloride. The concentration of Cr(VI) is calculated by difference of total chromium and Cr(III) levels. The analytical parameters including pH of the aqueous medium, amount of Pr(III), centrifugation speed, sample volume were optimized. The influences of matrix ions were also investigated. The method was validated by the analysis of TMDA 70 fortified lake water certified reference material. The method was applied to the speciation of chromium in water samples.     

The (salophen)-bridged Fe/Cr (III) capped complexes with triphenylene core: Synthesis and characterization

This article describes synthesis of the difference carboxylic acid derivatives of triphenylene and its complexation properties with Fe/Cr (III)-salophen. For this purpose, the carboxylic acid derivatives of 2,3,6,7,10,11-hexahydroxytriphenylene were synthesized and then reacted with four new Fe(III) and Cr(III) complexes involving tetradenta Schiff bases bis(salicylidene)-o-phenylenediamine-(salophenH₂). The prepared compounds were characterized by means of elemental analysis carrying out infrared spectroscopy (IR), thermogravimetric analysis (TG), nuclear magnetic resonance (¹H NMR), elemental analysis and magnetic susceptibility measurement. The complexes can also be characterized as low-spin distorted octahedral Fe(III) and Cr (III) bridged by carboxylic acids.     

Determination of chromium(III) and total chromium in marine waters

The development of an analytical technique is described which may be used to determine chromium, chromium(III) and chromium(VI) in estuarine and coastal waters. The method is based on selective micro-solvent extraction with subsequent GFAAS. The technique has been applied in a major North Sea estuary. The results obtained confirm that thermodynamic factors alone cannot be relied upon to describe the form of chromium in estuaries. Kinetic factors appear to have a strong influence over speciation and lead to the persistence of Cr(III) species in environments where Cr(VI) would be expected to be present.     

Speciation studies by capillary electrophoresis- Simultaneous determination of chromium(III) and chromium(VI)

A method for the simultaneous determination of chromium(III) and chromium(VI) by capillary electrophoresis (CE) has been developed. The chromium(III) has been chelated with 1,2-cyclohexanediaminetetraacetic acid (CDTA) in order to impart a negative charge and similar mobility to both the chromium(III) and the chromium(VI) species. The effects of the amount of the reagent, pH and heating time required to complete the complexation have been studied. Factors affecting the CE behaviour such as the polarity of electrodes and the pH of electrophoretic buffer have been investigated. The separated species have been monitored by direct UV measurements at 214 nm. The detection limits achieved are 10 microg/l for Cr(VI) and 5 microg/l for Cr(III) and linear detector response is observed up to 100 mg/l. The procedure has been applied to the determination of both chromium species in industrial electroplating samples and its accuracy was checked by comparing the results (as total chromium) with those of atomic absorption spectrometry. No interference occurred from transition metal impurities under optimized separation conditions. The method is also shown to be feasible for determining Cr(III) as well as other metal ions capable to form complexes with CDTA (like iron(III), copper(II), zinc(II) and manganese(II)) in pharmaceutical preparations of essential trace elements.     

Determination of chromium(III) and total chromium in marine waters

The development of an analytical technique is described which may be used to determine chromium, chromium(III) and chromium(VI) in estuarine and coastal waters. The method is based on selective micro-solvent extraction with subsequent GFAAS. The technique has been applied in a major North Sea estuary. The results obtained confirm that thermodynamic factors alone cannot be relied upon to describe the form of chromium in estuaries. Kinetic factors appear to have a strong influence over speciation and lead to the persistence of Cr(III) species in environments where Cr(VI) would be expected to be present.     

Cr(III) and Cr(VI) on-line preconcentration and determination with high performance flow flame emission spectrometry in natural samples

Methods for the on-line chromatographic preconcentration of Cr(III) and Cr(VI) have been developed. Cr(VI) has been preconcentrated on an RP C18 silica based column with tetrabutylammonium-bromide (TBABr) as ion-pairing agent. Specially for Cr(III) a new and effective preconcentration technique based on the sorption of Cr(III)-ions in a C18 column in presence of KH-phthalate has been developed. The efficiency of sample introduction into the atomic emission spectrometer could be improved by hydraulic high pressure nebulization. For the detection of chromium the acetylene/N₂O flame has been used as a powerful emission spectrometric source. Applying these steps the detection limit (3) could be improved to 25 pg/mL for Cr(III) and to 20 pg/mL for Cr(VI). The method has been applied for the chromium speciation in natural water samples.     

Photolyse der Chrom(III)-azido-Komplexe und Darstellung des Chrom(V)-nitrido-Komplexes mit N,N′-Ethylen-bis(salicylaldimin)

Photochemical Reactions of Chromium(III) Azido Complexes. Preparation of Nitrido-N, N′-ethylene-bis(salicylideniminato) Chromium(V) Complex The azide to nitride ligand conversion in the coordination sphere of chromium(III) complexes under light of 313 nm excitation has been observed. This photochemical reaction has been used to prepare the nitrido-N, N′-ethylene-bis(salicylideniminato)-chromium(V) complex characterized by an elementar analysis, electron, absorption, IR, and ESR spectra. The results of previous authors that the 313 nm photolysis of Cr(NH₃)₅N₃²⁺ yields Cr²⁺ or coordinated nitrenes are reinterpreted solely by formation of chromium(V) nitrido species.     

Speciation of Cr(III) and Cr(VI) by Means of Melamine-Urea-Formaldehyde Resin and FAAS

 A method is described for the quantitative preconcentration and separation of trace chromium in water by adsorption on melamine-urea-formaldehyde resin. Cr(VI) is enriched from aqueous solutions on the resin. After elution the Cr(VI) is determined by FAAS. The capacity of the resin is maximal at ∼ pH 2. Total chromium can be determined by the method after oxidation of Cr(III) to Cr(VI) by hydrogen peroxide. The relative standard deviations (10 replicate analyses) for 10 mg/L levels of Cr(VI), Cr(III) and total chromium were 1.5, 3.5 and 2.8% respectively. The procedure has been applied to the determination and speciation of chromium in lake water, tap water and chromium-plating baths.     

Biphasic oxidation of diaquadichloro(1,10-phenanthroline)chromium(III) by N-bromosuccinimide and the formation of chromium(IV) and chromium(V)

The kinetics of oxidation of diaquadichloro(1,10-phenanthroline)chromium(III) complex, [Cr^III(phen)(H₂O)₂Cl₂]⁺, by N-bromosuccinimide (NBS) is biphasic. The first faster step involves the oxidation of Cr(III) to Cr(IV). The second slower step is due to the oxidation of Cr(IV) to Cr(V). The reaction product is isolated and characterized by electron spin resonance (ESR), IR, and elemental analysis. The chromium(V) product is consistent with the formula [Cr^V(phen)Cl₂(O)]Br. The rate constants k_f and k_s, for the faster and the slower steps respectively, were obtained using an Origin 9.0 software program. Values of both k_f and k_s, varied linearly with [NBS] at constant reaction conditions. The effect of pH on the reaction rate is investigated over the pH (4.11–6.01) range at 25.0°C. The rate constants k_f and k_s increased with increasing pH. This is consistent with hydroxo forms of the chromium species being more reactive than the aqua forms. Chromium(III) complexes, more often than not, are inert. The oxidation of the Cr(III) complex to Cr(IV), most likely, proceeds by an outer sphere mechanism. Since chromium(IV) is labile the mechanism of its oxidation to chromium(V) is not certain.     

Synthesis,characterization and susceptibility of bacteria against Sulfamethoxydiazine complexes of copper(II), zinc(II), nickel(II), cadmium(II), chromium(III) and iron(III)

Complexes of sulfamethoxydiazine with Cu(II), Zn(II), Ni(II), Cd(II), Cr(III) and Fe(III) have been synthesized and characterized on the basis of conductivity measurements, elemental analyses, UV, IR, ¹H?NMR and thermal studies. It is shown that sulfamethoxydiazine behaves as a bidentate ligand, binding the metal ion through the sulfonyl oxygen and sulfonamide nitrogen. In vitro susceptibility tests of these complexes against Escherichia coli, Bacillus subtilis, Proteus vulgaris and Staphylococcus aureus were carried out. The results show that the antibacterial activities of the complexes of Zn(II), Cu(II), Cr(III) and Fe(III) are, in general, stronger than that of sulfamethoxydiazine, while the complexes of Cd(II) and Ni(II) are less active.     

Separation of Cr(III) and Cr(VI) using melamine-formaldehyde resin and determination of both species in water by FAAS

A method is described for the determination of Cr(VI) and total chromium by FAAS. Cr(VI) is separated from Cr(III) by adsorption on melamine-formaldehyde resin. After elution of Cr(VI) with 0.1 mol/l NaAc solution, it is analysed by FAAS. Total chromium is determined by FAAS after conversion of Cr(III) to Cr(VI) by oxidation with hydrogen peroxide, total Cr(VI) is concentrated as above. If the total concentration of chromium is sufficient, the determination can be directly made by FAAS. Cr(III) can then be calculated by subtracting Cr(VI) from the total Cr. This method was successfully applied to the determination of chromium in lake water.     

Spectrophotometric determination of chromium(III, VI) by use of chromium(III, VI)-Chrome AzurolS-cetylpyridinium bromide-hydroxylamine hydrochloride-zinc(II) system

This paper shows that the sensitivity of the Cr(III, VI)—Chrome Azurol S (CAS)-cetylpyridinium bromide (CPB)—hydroxylamine hydrochloride system can be increased and the wavelength of maximum absorption slightly shifted by addition of zinc(II) and that the analytical data are practically identical for both Cr(III) and Cr(VI), indicating that under the conditions used both initial oxidation states of chromium yield the same final oxidation state, Cr(III). On the basis of the Cr(III, VI)—CAS—CPB—NH₂OH·HCl—Zn systems a new, highly sensitive and selective method for spectrophotometric determination of microamounts of Cr(III, VI) has been developed, with molar absorptivity of 1.27 × 10⁵ 1. mole⁻¹ . cm⁻¹ for the complex at 620 nm and linear calibration up to 0.4 μg/ml chromium. Various foreign ions do not interfere. The method can be applied to direct determination of chromium in steels.     

A new efficient adsorbent in the preconcentration studies of the Cr(III) and Fe(III) ions

In this study, the imine‐graphene hybrid material (HM) was used as an adsorbent for removal of Fe(III) and Cr(III) metal ions from the drinking waters. The adsorbent material (HM) was prepared at three steps. At the first step, the graphite was oxidized by Hummer's method for preparation of graphene oxide (GO), in the second step, the silanization derivative (GO‐APTES) was obtained from the reaction of the 3‐(trimethoxysilyl) propylamine and GO. In the final step, the hybrid material (HM) was synthesized from the reaction of the 3,5‐diiodosalicylaldehyde and GO‐APTES. The chemical structures of three materials GO, GO‐APTES and HB were characterized by using the FT‐IR, XRD, EDX, SEM, TEM and UV‐vis methods. Thermal properties of the materials GO, GO‐APTES and HB were investigated by TGA/DTA methods in the 25–1000°C temperature range. Adsorption and desorption studies of the hybrid material toward Fe(III) and Cr(III) metal ions were investigated using the Batch method. The effect of pH, contact time, temperature, concentration on the adsorption properties of the hybrid material were investigated by ICP‐OES. The Fe(III) and Cr(III) ions have the maximum adsorption at the pH 7. The adsorption capacity decreases with the increase in pH values because above pH 9 the adsorption decreases due to the precipitation of metal hydroxide.     

Cr(III), Fe(III) and Co(III) complexes of tetradentate (ONNO) Schiff base ligands: synthesis, characterization, properties and biological activity

A series of metal complexes were synthesized from equimolar amounts of Schiff bases: 1,4-bis[3-(2-hydroxy-1-naphthaldimine)propyl]piperazine (bappnaf) and 1,8-bis[3-(2-hydroxy-1-naphthaldimine)-p-menthane (damnaf) with metal chlorides. All of synthesized compounds were characterized by elemental analyses, spectral (UV-vis, IR, (1)H-(13)C NMR, LC-MS) and thermal (TGA-DTA) methods, magnetic and conductance measurements. Schiff base complexes supposed in tetragonal geometry have the general formula [M(bappnaf or damnaf)]Cl.nH(2)O, where M=Cr(III), Co(III) and n=2, 3. But also Fe(III) complexes have octahedral geometry by the coordination of two water molecules and the formula is [Fe(bappnaf or damnaf)(H(2)O)(2)]Cl. The changes in the selected vibration bands in FT-IR indicate that Schiff bases behave as (ONNO) tetradentate ligands and coordinate to metal ions from two phenolic oxygen atoms and two azomethine nitrogen atoms. Conductance measurements suggest 1:1 electrolytic nature of the metal complexes. The synthesized compounds except bappnaf ligand have the antimicrobial activity against the bacteria: Escherichia coli (ATCC 11230), Yersinia enterocolitica (ATCC 1501), Bacillus magaterium (RSKK 5117), Bacillus subtilis (RSKK 244), Bacillus cereus (RSKK 863) and the fungi: Candida albicans (ATCC 10239). These results have been considerably interest in piperazine derivatives due to their significant applications in antimicrobial studies.     

Valence-to-core X-ray emission spectroscopy identification of carbide compounds in nanocrystalline Cr coatings deposited from Cr(III) electrolytes containing organic substances

Valence-to-core X-ray emission spectroscopy was applied to study a composition of chromium coatings electrodeposited from Cr(III) sulfate electrolytes with the addition of formic or oxalic acid. It was shown that the obtained crystallographically amorphous deposits contain chromium carbide compounds. These results indicate that nanodimensional Cr crystallites formed during the electrodeposition process are characterized by very high electrocatalytic activity.     

Speciation studies by capillary electrophoresis- Simultaneous determination of chromium(III) and chromium(VI)

A method for the simultaneous determination of chromium(III) and chromium(VI) by capillary electrophoresis (CE) has been developed. The chromium(III) has been chelated with 1,2-cyclohexanediaminetetraacetic acid (CDTA) in order to impart a negative charge and similar mobility to both the chromium(III) and the chromium(VI) species. The effects of the amount of the reagent, pH and heating time required to complete the complexation have been studied. Factors affecting the CE behaviour such as the polarity of electrodes and the pH of electrophoretic buffer have been investigated. The separated species have been monitored by direct UV measurements at 214 nm. The detection limits achieved are 10 g/l for Cr(VI) and 5 g/l for Cr(III) and linear detector response is observed up to 100 mg/l. The procedure has been applied to the determination of both chromium species in industrial electroplating samples and its accuracy was checked by comparing the results (as total chromium) with those of atomic absorption spectrometry. No interference occurred from transition metal impurities under optimized separation conditions. The method is also shown to be feasible for determining Cr(III) as well as other metal ions capable to form complexes with CDTA (like iron(III), copper(II), zinc(II) and manganese(II)) in pharmaceutical preparations of essential trace elements.