等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

“线上线下-虚实结合”在有机化学实验教学中的应用探索——以正溴丁烷的制备实验为例

In response to the impact of the Covid-19 epidemic on organic chemistry laboratory teaching, this article analyzes and discusses the current limitation of traditional organic chemistry laboratory teaching. Taking the "preparation of n-bromobutane" as an example, a new "online-offline and virtual-actual combination" teaching mode with the combination of "Tencent Meeting, MLabs, laboratory and WeChat group" is introduced. The practice of the new mode of teaching includes the following steps: pre-class online guiding by teacher, student preview and practice based on the virtual simulation platform, students and teacher discussion and operation in laboratory, and post-classcomprehensive assessment and Q&A", and good teaching effects have been received. It is significant in cultivating and improving the independent innovation and practical ability, and provides reference for the organic chemistry laboratory teaching reform and also lays a foundation for the construction of "outstanding course" of organic chemistry.     

以学为中心的高分子化学线上教学实践

In response to the COVID-19 epidemic prevention, the "polymer chemistry" course teaching team actively explored the "learning-centered" online teaching model. The students were guided to active learning by using the rich contents of Chaoxin online teaching platform and multiple online teaching activities. The basic knowledge points, difficulties and emphases of the teaching were highlighted and the real-time communication and Q&A were achieved in combination with the Tencent course live broadcast and QQ learning group. Following the concept of "students as the main body and teachers as the leading", the online teaching of "polymer chemistry" has effectively aroused the students' interest in learning, cultivated the initiative of autonomous learning, organically integrated the ideological and political education, and achieved a good learning outcome.     

基于“学习金字塔理论”的物理化学实验教学模式改革实践

介绍了东北林业大学物理化学实验课程教学中基于"学习金字塔理论"进行教学模式改革实践的情况。在实施实验教学过程中,通过增加"学生通过在线实验视频预习""学生为学生讲解实验""操作前学生小组讨论"和"操作后学生小组总结讨论"等学习环节,建立了一种有效的"以学生为中心"的实验教学模式,促进了学生综合素质和创新能力的培养,取得了良好的教学效果。     

针对理论-实验教学相融合的微助教辅助实验教学实践——以滴定分析实验教学为例

为了促进滴定分析理论-实验教学的融合,在借鉴疫情期间线上教学模式经验的基础上,我们在滴定分析内容教学中实践了微助教辅助的实验课堂教学模式。该教学模式灵活机动,不受行政班级划分与理论实验教学先后顺序的制约,能够有效地提高实验课教学效果,促进理论-实验教学相互融合,提升教学质量。     

有机化学与实验课程在线“双练教学”模式的探索与实践

In the online organic chemistry and laboratory courses, the open or semi open quizzes before class and after class are adopted to explore the "dual quizzes teaching" mode on the network teaching platform. As the progress of "dual quizzes teaching", students' learning weakness, confidence and enthusiasm are improved continuously. Through the analysis of online students' learning data, questionnaire and interactive feedback, the teachers can evaluate the learning situation of the students and regulate instructional content in time. As a result of teaching online, the "dual quizzes teaching" mode has achieved highly positive effect.     

虚拟仿真实验项目助力实验课在线教学

Due to the outbreak of the COVID-19 epidemic, the new semester has been postponed. But in order to continue teaching and student training work, teachers from colleges are efficiently utilizing internet education resources, and actively carry out online teaching. This paper uses one of the virtual simulation experiment projects at Shandong University, as an example. It introduces how to conduct online laboratory training and teaching in inorganic and analytical chemistry laboratory by utilizing the combination of virtual simulation experiment projects and online resources, and help student learn the theory and operation of iodometry titration.     

基于“超星直播+学习通”的在线教学示范

为了应对新冠病毒肺炎(COVID-19)蔓延和响应教育部"停课不停教,停课不停学"的号召,作者从"两问题三误区"入手分析了现有在线教学存在的问题,并对比了不同直播平台的优缺点,提出了在线教学的具体教学建议。以基于"超星直播+学习通"的在线教学为例进行了教学示范指导。     

“课前六备、课中六讲、课后六辅”在线课程混合式教学模式研究与实践——以基于“雨课堂+钉钉直播”的中等无机化学课程为例

Taking the online teaching of "inorganic chemistry" course at Dezhou University as an example, the "six steps before class, six steps in class, six steps after class" online course teaching model based on "Rain Class + Dingding Live" and an online "short class" were constructed. The main content and implementation methods of teaching design, teaching process, teaching effect, teaching reflection, teaching evaluation in online course teaching were discussed. It has been proved in practice that this model can effectively improve students' learning interest and enhance teaching effects.     

关于应对疫情开展化学类专业课程线上教学的探究

This paper aims at the implementation of the online courses of chemistry majors in Sichuan University in response to the epidemic, and explores a more effective and reasonable way to organize teaching. Based on the investigation and feedback of teachers and students, this paper points out the difficulties and challenges of online teaching at the present stage:the classroom interaction and discussion are not smooth, the online teaching tools and methods are diversified, and the chemistry laboratory courses are not matched. Therefore, the School of Chemistry of Sichuan University will coordinate the online teaching platform, enhance the classroom interaction, and launch the "chemistry virtual simulation experiment teaching center" to ensure the teaching progress and quality during the epidemic prevention and control.     

基于“1+2”模式的结构化学课程在线教学实践

Since the outbreak of novel coronavirus pneumonia (NCP) at the beginning of this year, Chinese government acted immediately and made some regulations to control the epidemic NCP and promote the recovery of society and industry including education. Chinese universities stayed on the online courses without suspension on teaching and learning. Herein, we report online teaching of structural chemistry course based on the teaching mode of online live broadcast platform, online course resources and management platforms ("1 + 2" mode). This may promote online teaching, and take advantage of online live broadcast and massive open online courses, which achieves good teaching and learning experiences on structural chemistry course.