深海采矿系统中悬臂式立管涡激振动分析

不同于传统的海洋立管, 深海采矿系统中的垂直提升管道可以被视为一个底部无约束的柔性悬臂式立管, 工作过程中同样面临涡激振动和柔性变形问题. 本文采用一种无网格离散涡方法和有限元耦合的准三维时域求解数值模型, 系统性地研究了不同流速下悬臂式立管的涡激振动问题. 结果表明: 悬臂式立管的横向振动模态阶数随折合速度增加而增大, 在一定折合速度范围内主导振动模态保持不变; 当主导模态转变时, 对应的横向振幅会发生突降, 但是当新的高阶模态被激发后, 立管振幅随来流速度增加而再次逐渐增大; 在相同的振动模态下, 立管底部位移均方根值随折合速度线性增加, 主导振动频率在模态转变时会出现跳跃现象; 特别地, 本文讨论了三阶主导模态下悬臂式立管的振动响应, 无约束的立管底部呈现出较大的振动能量, 且振幅的驻波特征随折合速度增加而逐渐增强; 本文比较了两端铰支立管与悬臂式立管的涡激振动响应特征, 两者在振幅和主导振动频率两方面均表现出了相同的变化趋势.      

剪切流场中含内流立管横向涡激振动特性

立管是海洋工程中输送油气或其他矿产资源的必备结构, 外部洋流引起的立管涡激振动影响着立管的疲劳寿命, 危害深海资源开发. 本文基于欧拉?伯努利梁方程, 结合半经验时域水动力模型, 建立剪切流与内流耦合作用下海洋立管涡激振动预报模型, 运用有限元方法和Newmark-β逐步积分法求解方程, 首先将数值模拟结果与实验数据进行对比, 验证模型正确性. 然后, 运用此模型, 对剪切流作用下含内流的顶张立管在不同内流速度和密度下的横向涡激振动响应特性进行研究, 主要分析了立管的横向振动模态、振动频率以及均方根位移等涡激振动参数随内流速度和密度等参数的变化规律. 结果表明, 在剪切流场中, 含内流海洋立管在横向上表现出多模态多频率的涡激振动;立管横向振动的最大均方根位移随内流速度和密度的增大而增大, 特别是当内流速度较大时, 横向最大均方根位移增大明显;立管横向振动的主导频率随内流速度和密度的增大而减小, 并且内流密度的增大同样会引起模态转换和频率转换.      

剪切流下发生涡激振动的柔性立管阻力特性研究

利用缩尺模型试验的方法研究了线性剪切流下涡激振动发生时柔性立管的阻力特性.文中基于光纤光栅应变传感器测得的模型应变信息,采用梁复杂弯曲理论计算了立管的平均阻力,继而分析了阻力系数沿管长方向和雷诺数的分布特性以及涡激振动对阻力系数的放大效应,并提出了用于估算柔性立管发生涡激振动时阻力系数的经验公式.结果表明:涡激振动对阻力系数有放大效应,使得立管局部阻力系数高达3.2;平均阻力系数在1.0×104到1.2×105的雷诺数区间内的值为1.3~2.0,并随雷诺数的增大而减小.本文提出的经验公式可准确估算高雷诺数下涡激振动发生时柔性立管的阻力系数,此经验公式考虑了流速、涡激振动主导模态以及主导频率对阻力系数的影响.      

正弦振荡来流下柔性立管涡激振动发展过程

在风浪流的作用下,海洋浮式结构物将带动悬链线立管在水中作周期性往复运动,从而在立管运动方向上产生相对振荡来流,这种振荡来流将激励立管悬垂段发生“间歇性” 的涡激振动. 在海洋工程水池中对一个4m 长的立管微段进行模型试验研究,以探索相对振荡来流作用下立管涡激振动产生的机理及其发展的物理过程. 试验通过振荡装置带动模型作正弦运动来模拟不同最大约化速度U_Rmax、不同KC（Keulegan-Carpenternumber）的相对振荡来流,利用光纤应变片测量立管涡激振动响应. 结合模态分析方法处理试验数据得到位移响应时历,继而提出相对振荡来流下柔性立管涡激振动发展的3 个阶段:建立阶段、锁定阶段以及衰减阶段. 并进一步总结了最大约化速度U_Rmax,KC 对涡激振动发展过程的影响规律. 最终获得不同最大约化速度U_Rmax下,涡激振动各发展阶段随KC 所占时间分布比例图.      

不同剪切率来流作用下柔性圆柱涡激振动数值模拟

采用浸入边界法对细长柔性圆柱在线性剪切流条件下的涡激振动进行三维数值模拟.细长柔性圆柱振动采用三维索模型模拟,其两端铰接,质量比为6,长细比为50,无量纲顶张力为496.来流为线性剪切流,剪切率从0到0.024变化,最大雷诺数为250.研究发现:剪切流作用下柔性立管横流向振动表现为驻波模式,而顺流向振动表现为行波与驻波混合模式.随着剪切率增大,振动频谱呈现多频响应,振动能量逐渐向低频转移.阻力系数平均值随着展向变化,脉动阻力系数和升力系数的均方根值均表现为"双峰"模式.流固能量传递系数沿立管轴向的分布表明,振动激励区集中于高流速区,而振动阻尼区多位于低流速区.剪切率较小时,圆柱的泻涡为平行交叉模式;剪切率较大时,圆柱的泻涡为倾斜泻涡模式,且由于泻涡频率沿立管轴向变化,尾流发生涡裂现象,形成泻涡频率不同的胞格结构.     

不同剪切率来流作用下柔性圆柱涡激振动数值模拟

采用浸入边界法对细长柔性圆柱在线性剪切流条件下的涡激振动进行三维数值模拟。细长柔性圆柱振动采用三维索模型模拟,其两端铰接,质量比为6,长细比为50,无量纲顶张力为496。来流为线性剪切流,剪切率从0到0.024变化,最大雷诺数为250。研究发现:剪切流作用下柔性立管横流向振动表现为驻波模式,而顺流向振动表现为行波-驻波混合模式。随着剪切率增大,振动频谱呈现多频响应,振动能量逐渐向低频转移。阻力系数平均值随着展向变化,脉动阻力系数和升力系数的均方根值均表现为“双峰”模式。流固能量传递系数沿立管轴向的分布表明,振动激励区集中于高流速区,而振动阻尼区多位于低流速区。剪切率较小时,圆柱的泻涡为平行交叉模式;剪切率较大时,圆柱的泻涡为倾斜泻涡模式,且由于泻涡频率沿立管轴向变化,尾流发生涡裂现象,形成泻涡频率不同的胞格结构。      

柔性圆柱涡激振动流体力系数识别及其特性

涡激振动是诱发海洋立管、浮式平台系泊缆和海底悬跨管道等柔性圆柱结构疲劳损伤的重要因素.目前,海洋工程中用于柔性圆柱涡激振动预报的流体力系数主要来源刚性圆柱横流向受迫振动的实验数据,存在一定缺陷和误差.本文综合考虑横流向与顺流向振动耦合作用,建立了柔性圆柱涡激振动流体力模型,运用有限元法和最小二乘法确定升力系数、脉动阻力系数和附加质量系数.为了准确识别柔性圆柱涡激振动流体力系数,设计并开展了拖曳水池模型实验,实验用柔性圆柱模型的质量比为1.82,长径比为195.5.通过与刚性圆柱流体力系数对比,深入分析了柔性圆柱流体力系数的特性.结果表明:柔性圆柱在一阶模态控制区,流体力系数随约化速度变化趋势与刚性圆柱大致相似;二阶模态控制区,升力系数和脉动阻力系数显著增大;附加质量系数在响应频率较低时与振动位移的相关性增强;当响应频率较低时,振动位移较大区域为能量耗散区,当响应频率较高时,振动位移较大区域为能量输入区.     

多用途输液立管涡激振动实验研究与疲劳分析

为研究输运不同流体的海洋立管在海流作用下的振动规律,在大型波浪流水槽中进行涡激振动模型实验。实验分别将四种不同质量比的立管模型竖直固定于支架上,立管外部承受不同速度的流体作用,上端施加顶张力。立管模型上均匀布置六个测点,根据每个测点布置的两个应变计,分别测得来流向和横向两个方向振动响应。通过小波变换对实验数据进行去噪处理,利用振型分解法求解立管各点涡激振动位移。考察输运不同流体对立管自振频率以及涡激振动响应的影响,并利用雨流计数法对模型进行疲劳分析。实验结果表明,随质量比增加立管涡激振动频率降低;低质量比的立管更容易产生大位移。     

深海细长柔性立管涡激振动数值分析方法研究进展

深海细长柔性立管的涡激振动与刚性圆柱的涡激振动问题相比,既有联系又有区别.当立管的长细比(L/D)较大时,会展现出一些刚性圆柱涡激振动没有的现象.本文介绍了近几十年来深海开发的细长柔性立管涡激振动的研究进展,主要侧重于数值计算分析研究领域,对目前常用的数值分析方法进行了归纳和总结.在此基础之上,详细介绍了目前理论研究和实际工程中的热点问题,诸如流场剖面的影响、立管顶端浮体运动的耦合、涡激振动抑制措施、振动多模态特性等.     

基于能量传递规律的海洋立管涡激振动抑制研究

涡激振动是造成海洋立管疲劳损伤的重要因素, 抑制振动能够保障结构安全, 延长使用寿命. 多数涡激振动抑制方法基于干扰流场的方式, 但在复杂环境条件下, 仅通过干扰流场对振动的抑制效果有限. 因此, 从结构层面考虑开展了海洋立管涡激振动抑制研究. 基于能量传递的理论, 阐述了立管涡激振动过程中的能量传递规律. 振动能量以行波形式由能量输入区传播至能量耗散区, 主要在能量耗散区被消耗. 通过局部增大能量耗散区的阻尼, 增加振动能量在传播过程中的消耗, 实现涡激振动抑制. 为了求解立管涡激振动响应, 构建了尾流振子预报模型, 并根据实验结果验证了理论模型的可靠性. 基于理论计算得到的能量系数, 判定立管涡激振动的能量输入区和能量耗散区. 通过对比立管增大阻尼前后的响应, 分析了涡激振动抑制效果. 研究结果表明: 在能量输入区增大阻尼对涡激振动的抑制效果并不显著; 在能量耗散区增大阻尼使能量衰减系数达到临界值之后, 能够显著降低立管上部和底部的涡激振动位移; 当能量衰减系数超过临界值后, 继续增大耗散区阻尼对涡激振动抑制效果的提升不明显.      

On shear flow single mode lock-in with both cross-flow and in-line lock-in mechanisms

A long flexible cylinder exposed to ocean currents is known to undergo vortex-induced vibration (VIV). In a spatially sheared flow the response of a riser to VIV can vary from single mode lock-in to multimodal. A new experimental facility was designed and built to investigate the above-mentioned areas. The facility consisted of a long flexible cylinder in either a uniform or a simplified vertically sheared flow. The instrumentation consisted of direct local fluid force measurement at two locations on the cylinder as well as accelerometers spaced along the cylinder axis. The simplified shear flow was a 2-slab flow, with each slab having uniform velocity. Test conditions included forcing the cylinder simultaneously at resonance in both regions to investigate modal competition issues and multimodal response patterns. Resonant VIV excitation of two different modes simultaneously, was conducted which revealed single mode lock-in of the higher frequency through an unexpected mechanism. The higher frequency mode's damping region underwent in-line excitation at four times the predicted shedding frequency that provided a power-in effect to support the dominant mode's cross-flow response.     

Modal analysis of measurements from a large-scale VIV model test of a riser in linearly sheared flow

Large-scale model testing of a tensioned steel riser in well-defined sheared current was performed at Hanøytangen outside Bergen, Norway in 1997. The length of the model was 90 m and the diameter was 3 cm. The aim of the present work is to look into this information and try to improve the understanding of vortex-induced vibrations (VIV) for cases with very high order of responding modes, and in particular to study if and under which circumstances the riser motions would be single-mode or multi-mode. The measurement system consisted of 29 biaxial gauges for bending moment. The signals are processed to yield curvature and displacement and further to identify modes of vibration. A modal approach is used successfully employing a combination of signal filtering and least-squares fitting of precalculated mode-shapes. As a part of the modal analysis, it is demonstrated that the equally spaced instrumentation limited the maximum mode number to be extracted to be equal to the number of instrumentation locations. This imposed a constraint on the analysis of in-line (IL) vibration, which occurs at higher frequencies and involves higher modes than cross-flow (CF). The analysis has shown that in general the riser response was irregular (i.e. broad-banded) and that the degree of irregularity increases with the flow speed. In some tests distinct spectral peaks could be seen, corresponding to a dominating mode. No occurrences of single-mode (lock-in) were seen. The IL response is more broad-banded than the CF response and contains higher frequencies. The average value of the displacement r.m.s over the length of the riser is computed to indicate the magnitude of VIV motion during one test. In the CF direction the average displacement is typically 1/4 of the diameter, almost independent of the flow speed. For the IL direction the values are in the range 0.05–0.08 of the diameter. The peak frequency taken from the spectra of the CF displacement at riser midpoint show approximately to be equal to the Strouhal frequency. The peak frequency in IL direction was typically twice the Strouhal frequency.     

An experimental investigation on vortex induced vibration of a flexible inclined cable under a shear flow

In the present study, an experimental investigation was performed to characterize the vortex induced vibration (VIV) of a flexible cable in an oncoming shear flow. The VIV tests were conducted in a wind tunnel with a flexible cable model. It was found that, under different oncoming velocity profiles, the cable model behaved in single-mode and multi-mode VIVs. The displacement amplitudes of the single mode VIVs were found to be larger than those of multi-mode VIVs, and the cross-flow (CF) response was larger than that of in-line (IL) direction for either the single mode or multi-mode VIVs. For a single mode vibration, the largest CF response occurs in the 1st mode VIV, and the motion trajectory of the 1st mode VIV was found to be an inclined figure of eight shape, while other single mode VIVs behaved in ellipse or straight line trajectories. For multi-mode VIVs, no stable vibration trajectories were found to exist since the vibration frequency bands covered two or more vibration modes. The vortex-shedding frequencies in the wake behind the inclined cable were also characterized in the present study. The shedding frequencies of the wake vortices were found to coincide well with the vibration modes: for a single mode VIV, they were close to the dominant vibration mode; for a multi-mode VIV, they could also cover the appearing vibration modes.     

近壁面柱体涡激振动的迟滞效应

柱体涡激振动是典型的流固耦合问题,其响应规律标识码在升速流动和远离壁面条件下获得的. 而自然环境流动通常不断经历升速和降速过程,近壁面柱体的涡激振动可呈现与远离标识码体不同的响应特征. 本研究结合大型波流水槽,设计了具有微结构阻尼的柱体涡激振动装置. 基于量纲分析,开展系列水槽标识码验,通过同步测量柱体涡激振动位移时程和绕流流场变化,研究了升降流速作用下柱体涡激振动触发和停振的临界速度(即上临标识码临界速度)变化规律,探究了近壁面柱体涡激振动迟滞效应. 采用自下向上激光扫射的 PIV 流场测量系统,对比分析了固定柱体标识码振动柱体的绕流特征. 实验观测表明,近壁面柱体涡激振动触发的临界速度呈现随壁面间距比减小而逐渐减小的变化趋势;但标识码速条件下的涡激振动停振所对应的下临界速度却明显小于升速时的涡激振动触发所对应的上临界速度. 采用上临界与下临界约标识码差值可定量表征涡激振动迟滞程度,研究发现该值随着柱体间距比减小呈线性增大趋势. 涡激振动迟滞现象通常伴随振幅阶跃标识码阶跃值则随着间距比减小而非线性减小.      

Drag amplification of long flexible riser models undergoing multi-mode VIV in uniform currents

Measurement data of long flexible riser models are used to study the drag amplification due to multi-mode vortex induced vibration (VIV). The riser model was towed in a towing tank, and vibration along its length was measured indirectly at a set of discrete points using accelerometers, along with the total drag and lift forces on the model. These data were used to fit expressions for the drag amplification taking into account the spatial variation of the vibration amplitude along the riser length. The results were compared with the existing empirical expression used in the VIV analysis tool SHEAR7 as well as other test data. It was found that the expression in SHEAR7 agrees well with the test data. However, for larger vibration amplitudes, it appears to under-predict the drag amplification.     

Effects of tension on vortex-induced vibration (VIV) responses of a long tensioned cylinder in uniform flows

The effects of tension on vortex-induced vibra-tion (VIV) responses for a tension-dominated long cylinder with an aspect ratio of 550 in uniform flows are experimen-tally investigated in this paper. The results show that elevated tension suppresses fluctuations of maximum displacement with respect to flow velocity and makes chaotic VIV more likely to appear. With respect to periodic VIV, if elevated tension is applied, the dominant vibration frequency in the in-line (IL) direction will switch from a fundamental vibra-tion frequency to twice the value of the fundamental vibration frequency, which results in a ratio of the dominant vibration frequency in the IL direction to that in the cross-flow direc-tion of 2.0. The suppression of the elevated tension in the fluctuation of the maximum displacement causes the axial tension to become an active control parameter for the VIV maximum displacement of a tension-dominated long riser or tether of an engineering structure in deep oceans. However, the axial tension must be optimized before being used since the high dominant vibration frequency due to the elevated tension may unfavorably affect the fatigue life of the riser or tether.     

A harmonic balance technique for the reduced-order computation of vortex-induced vibration

We present a harmonic balance (HB) method to model frequency lock-in effect during vortex-induced vibration (VIV) of elastically mounted circular cylinder and a flexible riser section in a freestream uniform flow. The fluid flow and structure are coupled by a fixed-point iteration process through a frequency updating algorithm. By minimizing the structural residual in the standard least-square norm, the convergence of HB-based fixed-point algorithm is achieved for a range of reduced velocity. To begin with, the HB solver is first assessed for a periodic unsteady flow around a stationary circular cylinder. A freely vibrating circular cylinder is then adopted for the reduced-order computation of VIV at low Reynolds numbers of Re=100 and 180 with one- and two-degrees-of-freedom. The coupled VIV dynamics and the frequency lock-in phenomenon are accurately captured. The results show that the HB solver is able to predict the amplitude of vibration, frequency and forces comparable to its time domain counterpart, while providing a significant reduction with regard to overall computational cost. The proposed new scheme is then demonstrated for a fully-coupled three dimensional (3D) analysis of a linear-elastic riser section undergoing vortex-induced vibration in the lock-in range. The results reveal the 3D effects through isosurfaces of streamwise vorticity blobs distributed over the span of flexible riser section. In comparison to time domain results, the 3D flow-structure interactions are accurately predicted while providing a similar speed up rate that of 2D simulations. This further corroborates that the HB solver can be extended to 3D flow-structure dynamics without compromising efficiency and accuracy.