等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

H MAS NMR monitoring of the C-labeled carbon scrambling for propane in zeolite H-ZSM-5

It has been demonstrated that ¹H MAS NMR spectroscopy can be used as a tool for in situ monitoring the reaction kinetics of ¹³C-labeled carbon scrambling in alkane molecules adsorbed on zeolite catalysts at the reaction temperature of 540–570 K. The accuracy of the results and the time resolution are improved compared to ¹³C MAS NMR spectroscopy.     

高硅MFI分子筛膜的合成与低温脱除膜内有机模板剂

采用旋涂法在粗糙的α-Al₂O₃载体片上制备出较完备的分子筛晶种层;以四丙基氢氧化铵(TPAOH)为有机模板剂,通过调控合成液的H₂O/Si摩尔比,实现了对分子筛晶体面内优先生长的调控;经过三次水热合成得到致密交联的h0h-轴取向高硅MFI分子筛膜,膜厚约为8 μm(包括~5 μm致密层和~3 μm过渡层)。采用先低温加氢裂解后低温空气氧化的两步法脱除工艺,有效脱除了分子筛膜内的有机模板剂。相比于传统高温煅烧法,该法可以避免分子筛膜因脱除模板剂而形成的较大晶间缺陷。因而采用低温两步法脱除模板剂的分子筛膜片在30 ℃时具有较好的CO₂分离效果,其CO₂/N₂分离因子达到5.2, CO₂渗透通量高达5.8 × 10^-7mol·m^-2·s^-11·Pa^-1。     

NEW STEROIDAL CONSTITUENTS FROM AMALOCALYX YUNNANESIS----Ⅰ.

Two C_(21)-steroids,named amalogenin A amd amaloside A were isola-ted from the rhizome of Amalocalyx yunnanesis.Their structures were estab-lished by analysis on the spectra of NMR including ~1H-~1H cosy,~(13)C-~1H COSYand confirmed by X-ray diffraction.     

DFT计算结合固体NMR研究富铝SSZ-13的铝分布和Br?nsted酸性

具有菱沸石(CHA)结构的SSZ-13分子筛在甲醇制烯烃(MTO)及柴油机车尾气氨选择性催化还原(NH_3-SCR)反应中具有重要的应用,采用富铝SSZ-13可以调节MTO反应的烯烃选择性和提升NH_3-SCR的低温脱硝活性,因此SSZ-13中的铝含量和分布与对应的酸性决定了其催化性能。本文采用密度泛函理论结合固体核磁共振实验研究了富铝和富硅HSSZ-13的Al位置与Br?nsted酸强度的内在关系。通过计算取代能发现,对于孤立Al位,质子位于Al周围4个不同O位时能量差异较小,最稳定的B酸位点是O(1)―H。对于富铝SSZ-13,两个Al原子位于同一六元环的对位是Al-Si-Si-Al (NNNN)序列中最稳定的结构,而Al-Si-Al (NNN)序列中能量最优的Al分布是两个铝原子排布于六棱柱上下不同的六元环上。通过计算最稳定构型下的质子亲和势、NH3脱附能和吸附氘代乙腈后的1H NMR化学位移,发现富铝SSZ-13中含有Si(2Al)分布的NNN序列导致了其Br?nsted酸强度弱于高硅的分子筛。分峰拟合29Si魔角旋转核磁共振(MASNMR)谱图表明富铝SSZ-13中Si(2Al)的含量在43%以上,而吸附氘代乙腈后的1H MAS NMR实验显示富铝SSZ-13的桥羟基化学位移向低场移动,进一步证明富铝SSZ-13具有较弱的Br?nsted酸强度。     

X-ray and spectroscopic studies of the molecular structure of bis(8-oxy-1-methylquinolinium) hydroiodide

Bis(8-oxy-1-methylquinolinium) hydroiodide has been studied by X-ray diffraction, FT-IR, ¹H and ¹³C NMR spectroscopy. In the crystalline state a homoconjugated OH  O⁻ hydrogen bond is formed. As indicated by the X-ray data this hydrogen bond is very short (2.457 Å) and structurally symmetrical. The existence of this bond is manifested in the FT-IR spectra by an intense and broad band in the 1500–400 cm⁻¹ region. This type of absorption indicates that this hydrogen bond can be described by one very broad potential energy minimum in which the proton shows a large proton polarizability due to its fast fluctuations, i.e., it shows the so-called Zundel’s polarizability.     

部分还原二氧化钛的NMR和EPR研究

Partially reduced TiO₂ nanomaterials have attracted significant interest because of their visible-light activity for catalysis and photodegradation. Herein, we prepared a partially reduced anatase TiO₂ (Re-A-TiO₂) nanoparticle material using a fast combustion method, demonstrating good activity toward decomposing methyl orange under visible light irradiation. The surface structure of the prepared material, after being surface-selectively ¹⁷O-labeled with H₂¹⁷O (¹⁷O-enriched water), was studied via ¹⁷O and ¹H solid-state magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and electron paramagnetic resonance (EPR) spectroscopy, and the obtained results were compared to those of non-reduced anatase TiO₂ (A-TiO₂). The EPR results showed that the concentrations of paramagnetic species (i.e., oxygen vacancies (OV) and Ti³⁺) in Re-A-TiO₂ were much higher than that in A-TiO₂, while the former was associated with a higher OV/Ti³⁺ ratio. The intensities of the EPR signals were significantly affected by the adsorbed water, and this phenomenon was explored in combination with ¹H NMR spectroscopy. The ¹H species on Re-A-TiO₂ appeared at larger chemical shifts, denoting the increased acidity of the sample, and these ¹H species on Re-A-TiO₂ were more difficult to remove than those on A-TiO₂. On the other hand, different features were observed for the signals arising from the two-coordinated oxygen atoms (μ₂-O) in ¹⁷O NMR, suggesting a typical anatase TiO₂(101) surface on A-TiO₂, but a more complex surface environment for Re-A-TiO₂. Furthermore, a larger amount of hydroxyl groups (OH) were observed on Re-A-TiO₂ compared to that on A-TiO₂, indicating a larger proportion of exposed (001) facets on Re-A-TiO₂. However, the μ₂-O signals broadened and became similar when the drying temperature was increased to 100 ℃, indicating a non-faceted anatase TiO₂ surface in such conditions. Based on the EPR and NMR results, a significant fraction of the OH species is believed to be formed from the reaction of the paramagnetic centers and adsorbed water molecules. The ¹H→¹⁷O cross polarization (CP) MAS and two-dimensional heteronuclear correlation (2D HETCOR) NMR spectra were used to verify the spatial proximity of the hydrogen and oxygen species, confirming the spectral assignments of a strongly adsorbed water and one type of surface OH species. In particular, the ¹H NMR signals at approximately 11 ppm were ascribed to the hydrogen species in the intramolecular hydrogen bond. In summary, this study investigated the paramagnetic species and surface structure of anatase TiO₂ materials by combining EPR along with ¹H and ¹⁷O solid-state NMR spectroscopy. The differences in the surface structures of Re-A-TiO₂ and A-TiO₂ should be closely related to their different properties toward the photodegradation of methyl orange.     

固体NMR研究PAA/PEO共混物中氢键相互作用与结构演化

分子间相互作用是决定材料结构和性能的关键因素之一,而如何在分子水上实现对复杂相互作用分子的检测仍然是一个挑战性课题。本工作首先在不同p H值条下以聚丙烯酸/聚环氧乙烷(PAA/PEO)的混合水溶液制备了系列的固体薄膜,然后采用多种基于连续相调制多脉冲技术的一维和二维~1H多脉冲去耦(CRAMPS)固体NMR新技术,并结合高分辨~(13)C交叉极化魔角旋转(CPMAS)、~(23)Na多量子(MQ)等多核固体NMR实验,对PAA/PEO聚合物共混物的微观结构和动力学进行了原位和系统的研究。通过不同类型的~1H高分辨CRAMPS实验检测到共混物中包含多种不同类型质子:通过氢键相互作用形成二聚体的COOH基团、自由COOH基团、与水结合的COOH基团和主链基团。随着p H值的升高,除主链质子外,大部分其它区域的信号都明显降低,这是由于PAA与PEO以及水的氢键作用减弱所致。这些CRAMPS NMR技术也被用来阐明不同p H值制备的样品中不同基团的分子运动性。此外,二维~1H-~1H自旋交换NMR实验提供了关于聚合物PAA与PEO大分子链间、以及水与聚合物的相互作用。~1H自旋扩散实验表明,在这些共混物中明显存在相微观相分离的结构,并且测定的分散相区尺寸约为17 nm。~(23)Na MQMAS实验揭示了在共混物中存在两种类型~(23)Na位,一种是自由的钠离子,另一种是与大分子相互作用的Na离子。特别是通过~1H-检测的~(23)Na-~1H CPMAS实验揭示了Na~+离子的位置远离PEO而与PAA临近。上述这些SSNMR实验结果在分子水平上提供了氢键相互作用对PAA/PEO共混物微观结构和动力学影响的详细信息,可以获得不同p H值对PAA与PEO的氢键作用、相容性、微观结构、水-聚合物相互作用和不同组分分子运动性的影响。在上述核磁共振研究的基础上,我们提出了一种新的PAA/PEO共混物的结构模型,该模型首次成功地揭示了不同的p H值对PAA/PEO共混物中微观结构和动力学的影响。本工作清楚地表明,固态核磁共振是在分子水平上研究具有复杂相互作用的多相聚合物材料的有力工具。本文的研究工作对于探索检测聚合物弱相互作用的新方法和发展基于氢键相互作用的聚合物新材料的开发具有重要意义。     

亚胺型比色探针的制备及阴离子识别性能研究

合成了两种亚胺型阴离子识别受体:2-[(2-羟基-5-硝基亚苄基)氨基]4-硝基苯酚(R1)和2-[(蒽-9-亚甲基)氨基]-4-硝基苯酚(R2),其结构经核磁氢谱和红外表征.在紫外光谱实验中,受体R1和R2分别在乙腈和DMSO溶液中可以高选择性识别F-,AcC-和H2PO4-,同时观察到明显的颜色改变.实验结果表明,...     

异苯橡胶环化反应动力学研究及产物微细结构表征

本文采用红外光谱法研究了前无报导的聚异苯橡胶环化反应动力学,测定了标题反应的动力学参数:反应级数n=1;活化能E_a=53.2kJ·mol^-1;指前因子A=2.24×10⁶min^-1,确立了该反应速率常数k_T与s反应温度T之间的函数关系为:Ln(k_T/min^-1)=14.62-6.40×10³K/T并采用核磁共振法分析了标题反应的产物环化异苯橡胶的微细结构,提出了标题反应的可能机理,并对活化能及指前因子进行了分析讨论。     

NMR Study of Pore Surface and Size in a Mesoporous Material FSM-16

Surface structure, pore size distribution and pore wall thickness of a mesoporous material FSM-16 have been studied by X-ray powder diffraction (XRD), ^lH and ²⁹Si MAS NMR and ¹H liquid-state NMR, and by applying surface silylation as a probe. Concentrations of surface hydroxyl groups for FSM-16 are estimated from ²⁹Si and ¹H MAS NMR, which are about 3×l0²¹ g^-1, corresponding to approximately 3 nm^-2. O₂ molecules contribute to ²⁹Si spin-lattice relaxation of Q² and Q³ as well as Q⁴, suggesting thin wall thickness. ¹H MAS NMR spectra indicate the presence of isolated and hydrogen-bonded hydroxyl groups. Both hydroxyl groups are silylated, where the silylated fraction is about 50%. The spatial distribution of surface hydroxyl groups is estimated from the line width in ¹H static spectra. A rather homogeneous distribution is demonstrated in one of the samples. The sample with less homogeneous distribution has a larger affinity for moisture. Pore size and pore wall thickness were determined by ¹H NMR measurements on water saturated FSM-16 samples, which are in good agreement with literature values obtained by N₂ adsorption isotherms and transmission electron micrographs on a similar sample. In benzene saturated samples, a non-freezing surface layer of benzene is much thicker than that of water, which indicates a stronger interaction between benzene and the FSM-16 surface.