高温热稳定性Au/β-Mo2C催化剂的制备及在逆水煤气变换反应中的应用

以程序升温碳化法合成β-Mo2C载体,采用原位沉淀法制备负载量不同的Au/β-M o2C催化剂,利用XRD、STEM和氮气吸附-脱附等手段对Au在载体表面的分散性、微观形貌及孔结构等进行表征,并在逆水煤气变换(RWGS)反应中对其高温热稳定性进行了研究。XRD表征结果表明,在34. 44°、38. 02°、39. 44°、52. 12°、61. 53°、69. 62°和74. 65°处出现了β-Mo2C对应的(100)、(002)、(101)、(102)、(110)、(103)和(200)晶面的X射线特征衍射峰;同时,未出现Au物种的特征吸收峰,说明Au负载量较低的0. 1%和0. 5%的催化剂上Au纳米粒子的分散性较好。STEM表征结果也显示,当负载量较低(0. 5%、1. 0%和2. 0%)时,金纳米粒子以2 nm左右的原子簇形式均匀分散并锚定在β-M o2C载体上。氮气吸附-脱附表征结果表明,催化剂具有良好的介孔结构。反应评价结果表明,0. 2%Au/β-Mo_2C催化剂在RWGS反应中具有较好的催化活性和较高的CO选择性,且反应后孔结构良好,Au纳米粒子仍然均匀分散,说明Au/β-Mo_2C催化剂在此反应中具有较高的催化性能和高温热稳定性。     

高温沉淀铁基催化剂上费托合成含氧化合物生成机理的研究

采用漫反射原位红外光谱法及化学捕获方法,考察了费托合成过程中高温沉淀铁基催化剂表面吸附物种的变化,并探讨了含氧化合物的生成机理。结果表明,CO在高温沉淀铁基催化剂上有线式和桥式两种吸附态存在,同时,CO的吸附在催化剂表面生成大量含氧化合物前驱体。费托原位实验捕获到了一些较关键的中间产物:表面乙酸盐、表面酰基、甲氧基等。同时发现高温沉淀铁基催化剂表面具有以下反应共性:醇类可与表面羟基结合生成烷氧基团;催化剂表面的吸附分子具有氧化性;一些基础化学物质如OH^-、晶格氧等可以与甲醇或乙醛分子发生反应。对CH₃OH + CO及CH₃I + CO + H₂两个反应的化学捕获实验表明,酰基是C₂⁺含氧化合物的重要中间产物,酰基加氢是形成C₂⁺含氧化合物的关键步骤。根据表面中间产物及反应特性,得到了高温沉淀铁基催化剂上费托合成含氧化合物的生成机理。     

非等温硼酸酯化反应动力学研究

通过对酯化反应特点的分析,建立了只需跟踪反应出水量、反应时间和相应的体系温度,便可对非等温条件下酯化反应动力学进行定量分析的实验方法,并导出了用于计算动力学参数的理论公式.在此基础上研究了二甘醇独丁醚硼酸酯的合成动力学,经计算得知该反应为二级反应,表现活化能为98.33kj/mol,频率因子为1.048×10^7L·mol^-1·S^-1.文中通过一组不同升温速率条件下的实验数据,对反应动力学参数及所导计算公式进行了验证.     

海螺状碳酸钙的可控合成与荧光性能

采用液相沉淀法,以硝酸铋[Bi(NO_3)_3]为添加剂来调控碳酸钙晶体的形状与大小,制备了海螺状碳酸钙粒子.通过扫描电子显微镜(SEM)、X射线衍射仪(XRD)、热重分析仪(TGA)、原子荧光光谱仪(AFS)等对产物的结构和性能进行了表征.结果表明,在60℃条件下,添加20 mL浓度为2 g/L的Bi(NO_3)_3溶液可得到海螺状球霰石型碳酸钙粒子,且其荧光性明显增强.在碳酸钙的成核过程中,Bi~(3+)的加入起到了显著的调控作用.     

原位氧化还原沉淀水热合成法制备LixMn2O4尖晶石

Li xMn2O4尖晶石是新一代的锂离子二次电池正极材料 [1], 其合成方法对材料的电化学性质影响很大[2].常规合成大多采用高温固相反应法, 此法具有反应温度高, 反应时间长, 容易产生缺陷和产物不纯净等缺点, 导致所合成的锂离子二次电池正极材料的性能较差. 目前用水热合成法制备电池正极材料Li xMn2O4尖晶石尚未见文献报道. 本文在常规水热合成法的基础上采用原位氧化还原沉淀水热合成法 [3]制备前驱物, 该法合成条件更温和, 而且使材料的综合性能得到了改善和提高.      

尼龙1218的等温及非等温结晶动力学研究

采用示差扫描量热计DSC考察了一种新型长烷基链偶偶尼龙 尼龙 12 18 自熔体的结晶过程 ,分别利用Avrami方程和Ozawa方程对等温及非等温结晶动力学进行了描述与研究 ,计算了相关的结晶动力学参数 ,得出相应的结晶机理 .最后计算了等温结晶活化能和非等温结晶活化能 ,依此得到烷基链段长度与尼龙结晶过程有密切关系     

升温与等温法非模型动力学研究环氧树脂固化反应

基于DSC数据,采用以Vyazovkin积分法为基础的升温法非模型动力学和等温法非模型动力学对双酚A型环氧树脂E51/4,4′-二氨基二苯基砜(DDS)体系及多官能度环氧树脂AG80/DDS体系的固化过程进行了研究,并结合玻璃化转变温度的变化和原位红外测试技术,对比分析了升温与等温条件下的固化反应规律.结果表明,与传统的模型拟合法相比,非模型动力学更适合定量预测树脂固化反应过程,并能为固化过程中反应机理变化的研究提供重要依据;等温法非模型动力学能够更好地预测两种树脂体系在不同恒温条件下的固化反应历程,并且升温法与等温法非模型动力学所得到的反应活化能-固化度之间的变化关系不同,表明不同温度条件下树脂的反应机理不同,这与升温和恒温条件下玻璃化效应及环氧官能团的变化规律相吻合.     

微型流化床反应分析仪中原位/非原位煤焦气化动力学研究

利用新开发的微型流化床反应分析仪(micro-fluidized bed reaction analysis, MFBRA) 考察了义马烟煤半焦的原位以及两种非原位半焦气化行为并测定了其动力学参数,其中,原位半焦气化是指煤热解温度和气氛与半焦气化过程一致,非原位半焦1气化是指煤在Ar气氛下热解,热态条件下直接在CO₂气氛下气化;非原位半焦2气化是指煤在Ar气氛下热解,冷却收集后再在CO₂气氛下气化。研究发现,原位半焦具有最大的比表面积和最小的平均孔径,石墨化程度最弱,且对CO₂的化学吸附能力最强,表面活性位点最多。在最小化气体扩散的实验条件下,原位半焦气化反应的反应速率明显比非原位半焦气化反应快,且求取的活化能数据较小。实验揭示了原位半焦和非原位半焦结构和反应性的差异,也证明了MFBRA对原位等温气化反应的适用性。     

花椰菜状碳酸钙的"一步法"制备及表征

以碱土金属锶的硝酸盐为添加剂, 采用“一步法”制备了大小均一、 分散性良好的花椰菜状碳酸钙粒子. 考察了反应温度、 反应时间等因素对碳酸钙结晶行为的影响, 确定了最佳反应条件. 利用扫描电子显微镜(SEM)、 X射线衍射仪(XRD)、 X射线能谱仪(EDAX)等对所得产物的结构和性能进行了表征, 并探讨了其反应原理.     

非等温液-固相酯化反应动力学研究

根据稀土盐催化剂催化的乙二醇单乙醚醋酸酯的液相合成反应的特点,导出了非等温变体积条件下的反应速率方程,并提出了利用一条实验曲线,计算动力学参数的动态方法、以此为基础,对不同实验条件下的多组实验数据进行了动力学处理.大量计算结果表明,该反应服从二级动力学模型,表观反应活化能为213.59kJ·mol~(-1),指前因子为5.903×10~(25)dm~3·mol~(-1)·min~(-1)计算结果的合理性及一致性,进一步证明了动态原理用于液-固相反应体系的动力学研究是简便可行的     

Thermal behaviour and non-isothermal decomposition kinetics of some Nd(III) coordination compounds

The authors present the results concerning the thermal behaviour of three polynuclear coordination compounds of Nd(III) and Co(II) or Fe(III) with triptophan. For the dehydration steps the values of the non-isothermal kinetic parameters have been determined.     

Kinetics of non-isothermal decomposition of three IRGANOX-type antioxidants

In the present work a comparative kinetic study was performed on the thermal behavior of three antioxidants of IRGANOX-type (L101, L109 and L115) in dynamic air atmosphere under non-isothermal conditions. The TG-DTG data were obtained at heating rates of 5, 7, 10 and 15 K min⁻¹. The kinetic parameters were obtained by processing these data with strategies corresponding to Flynn-Wall-Ozava (FWO), Friedman (FR), Budrugeac-Segal (BS) and non-parametric kinetic (NPK) methods. The thermal degradation by all the three compounds take place in melted state, so that any kinetic models regarding the decomposition of solids are inapplicable. Only with the NPK method it was possible a separation between the two functions of the reaction rate. For the temperature dependence, f(T), an Arrhenius-type model was searched; for the conversion dependence, the Ŝestak-Berggren equation was suggested in order to discriminate between physical (m) and chemical (n or p) steps of a complex thermodegradation process.     

Synthesis and kinetics of non-isothermal degradation of acetylene terminated silazane

Novel acetylene terminated silazane compounds,with three types of substituent,were synthesized by the aminolysis of dichlorosilane with 3-aminophenylacetylene(3-APA).Thermal property of the compounds is studied by thermogravimetry analysis (TGA).It shows that the acetylene terminated silazane has high temperature resistance.The char yield at 1000℃is 77.6,81.9 and 68.7 wt%for methyl,vinyl,and phenyl substituted silazane,respectively.The pyrolysis kinetics of the silazane is investigated by non-isothermal thermogravimetric measurement.The pyrolysis undergoes three stages,which is resolved by PEAKFTT.The kinetic parameters are calculated by the Kissinger method.The role of functionalities on the thermal resistance is discussed.The vinyl-silazane exhibits higher thermal stability because of higher cross-linking density.     

Decomposition of Cyclohexyl-t-butyl-Dimethylammonium Tetraphenylborate: Synthesis and kinetics

A new compound cyclohexyl-t-butyldimethylammonium tetraphenylborate, [C₆H₁₁N(CH₃)₂(C(CH₃)₃)]BPh₄ has been prepared, and its decomposition mechanism was studied by TG. The IR spectra of the products of thermal decomposition were examined at every stage. Kinetic analysis for the first stage of thermal decomposition process was obtained by TG and DTG curves, and kinetic parameters were obtained from the analysis of the TG-DTG curves with integral and differential equations. The most probable kinetic function was suggested by comparison of kinetic parameters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Products and kinetics of non-isothermal decomposition of vanadium(IV) oxide compounds

The kinetics of dehydration and decomposition of VOSO₄·2H₂O, VOSO₄ and VOSeO₃·H₂O was studied under non-isothermal heating on a derivatograph. The stages and products of the thermal decomposition were determined. It was proved that VOSO₄·2H₂O decomposes to V₂O₅ while VOSeO₃·H₂O − to V₂O₄. A number of kinetic models and calculation procedures were used to determine the values of the kinetic parameters characterizing the process. The parameters calculated were compared and analyzed. IR-spectra of the initial substances and the solid residue after decomposition are presented.     

Model-free method for isothermal and non-isothermal decomposition kinetics analysis of PET sample

Pyrolysis, one possible alternative to recover valuable products from waste plastics, has recently been the subject of renewed interest. In the present study, the isoconversion methods, i.e., Vyazovkin model-free approach is applied to study non-isothermal decomposition kinetics of waste PET samples using various temperature integral approximations such as Coats and Redfern, Gorbachev, and Agrawal and Sivasubramanian approximation and direct integration (recursive adaptive Simpson quadrature scheme) to analyze the decomposition kinetics.The results show that activation energy (E_α) is a weak but increasing function of conversion (α) in case of non-isothermal decomposition and strong and decreasing function of conversion in case of isothermal decomposition. This indicates possible existence of nucleation, nuclei growth and gas diffusion mechanism during non-isothermal pyrolysis and nucleation and gas diffusion mechanism during isothermal pyrolysis. Optimum E_α dependencies on α obtained for non-isothermal data showed similar nature for all the types of temperature integral approximations.     

Kinetics of exothermal decomposition of 2-nitrophenylhydrazine and 4-nitrophenylhydrazine using DSC non-isothermal data

Kinetics of exothermal decomposition of 2-nitrophenylhydrazine (2-NPH) and 4-nitrophenylhydrazine (4-NPH) was investigated by differential scanning calorimetry. The isoconversional methods, Friedman and Flynn-Wall-Ozawa, were applied to determine the activation parameters from the common analysis of multiple curves measured at different heating rates. For the processes involving two-step reactions the multivariate non-linear regression was used. A good agreement between the experimental and the fitted data was found.     

Isothermal and non-isothermal crystallisation kinetics of pCBT and PBT

The crystallisation behaviour of in situ polymerised cyclic butylene terephthalates (pCBT) and poly(butylene terephthalate)s (PBT) were studied by differential scanning calorimetry (DSC) both under isothermal and non-isothermal conditions. The crystallisation was analysed by adopting the Avrami, Ozawa and Kissinger methods for the isothermal and non-isothermal crystallisations, respectively. An Avrami exponent n between 2 and 3 was found for the pCBTs whereas the exponent ranged between 3 and 4 for the PBTs. The Ozawa exponent m varied for all materials between 2 and 3. Differences in the crystallisation kinetics were also reflected in the related activation energy data.     

Non-isothermal kinetics of high temperature oxidation studied by a fast X-ray diffraction method

Temperature resolved X-ray diffraction using a diffractometer equipped with a high temperature device was applied to the study of the oxidation of Fe-ARMCO below 570°C. The oxidation products are identified in situ and the difference method yields curvesY(T) showing the global changes. These curves were calibrated to the microscopically measured end thickness of the oxide layer obtaining the growthx(T). A calculated curve including the Arrhenius relation was fitted to thex(T) curve yielding activation energy and values of the oxidation rate constant as a function of temperature.

---

Zusammenfassung Unter Anwendung eines Diffraktometers mit einer Hochtemperatureinheit wurde unterhalb 570°C mittels Röntgendiffraktion die Oxidation von Fe-ARMCO untersucht. Die Oxidationsprodukte wurden in situ bestimmt und das Differenzverfahren ergabY(T)-Kurven, die die globalen Änderungen zeigen. Diese Kurven wurden anhand der mikroskopisch bestimmten resultierenden Dicken der Oxidschicht kalibriert, wobei man die Funktionx(T) erhält. Dieser Kurve wurde eine berechnete, die Arrheniussche Beziehung enthaltende Funktion angepaßt, wodurch man die Aktivierungsenergie und die Oxidations Geschwindigkeitskonstante als Funktion der Temperatur erhält.