Preparation of styrene/acrylonitrile copolymer microspheres and their composites with metal particles

 Monodispersed poly(styrene-co-acrylonitrile) [P(St-co-AN)] microspheres were prepared by emulsifier-free emulsion copolymerization of St with AN. Fourier transform IR spectroscopy and elemental analysis were used to measure the content of AN in the poly(St-co-AN) microspheres. X-ray photoelectron spectroscopy (XPS) measurements indicated the presence of an AN unit on the surface of the microspheres. The combined results of the elemental analysis and the XPS measurements showed that the copolymer on the surface of the P(St-co-AN) particles was rich in AN compared with that in the interior of the particles. P(St-co-AN)–metal composite particles were prepared by chemical metal deposition. The addition of nickel could improve the distribution of cobalt on surface of the polymer microspheres. The preparation of polymer–bimetal composite particles was tried. Transmission electron microscopy and XRD were used to study the distribution and structure of the deposited metal particles. Received: 30 June 1999/Accepted in revised form: 16 September 1999     

Morphological investigations of crosslinked polystyrene microspheres by seeded polymerization

 Crosslinked polystyrene microspheres with novel surface and inner morphologies were synthesized by seeded polymerization following a seed-swelling method, using uncrosslinked polystyrene microspheres as seeds and a mixture of toluene, styrene (St), and divinylbenzene (DVB) as the swelling agent. With the increasing toluene/ (St+DVB) ratio, the crosslinked particles changed from smooth-surfaced spheres to deformed spheres with dimples or heavy dents at the surface. A single hole inside the spherical particles was produced at low St/DVB ratio, while higher St/DVB ratios gave irregular dented or dimpled particles. Ultrathin cross-section observation by TEM revealed a non-uniformly crosslinked inner structure. Received: 20 January 1998 Accepted: 14 April 1998     

Preparation of styrene/methacrylic acid copolymer microspheres and their composites with metal particles

 Poly(styrene-co-methacrylic acid) [P(St-co-MAA)] microspheres were prepared by emulsifier-free emulsion copolymerization of St with MAA. Fourier transform IR spectroscopy and elemental analysis were used to study the change in the content of MAA in the microspheres. The results of X-ray photoelectron spectroscopy measurements indicated the presence of carboxylic functionality on the surface of the microspheres. The P(St-co-MAA) metal composite particles were prepared by chemical metal deposition. Transmission electron microscopy observation and X-ray diffraction measurement were used to study the distribution and structure of the metal particles deposited. Received: 15 September 1999 Accepted: 24 December 1999     

Assembly of Fe2O3 Nanoparticles with Polymer Microspheres by Encapsulated Copolymerization

Inorganic nanoparticles Fe₂O₃ in diameter of 3-5 nm have been assembled with polymer microspherer and then encapsulated in copolymer of St/BA/AA by polymerization process. Fe₂O₃ encapsulated microspheres can obtained through interaction between surface groups of the two component particles and by adjusting the pH value in the emulsion. Pre-treatment of the composite particles using a certain amount of surfactant before polymerization can give a good encapsulation.     

Synthesis of poly(styrene-co-3-trimethoxysilyl propyl methacrylate) microspheres coated with polysiloxane layer

A procedure has been developed to coat micron-sized poly(styrene-co-3-trimethoxysilyl propyl methacrylate) microspheres with a smooth layer of polysiloxane by the hydrolysis and condensation of methyl trimethoxylsilane (MTMS). Firstly, polystyrene microspheres containing silanol groups were prepared by conventional dispersion polymerization using 3-(trimethoxysilyl) propyl methacrylate (MPS) as a functional comonomer in an ethanol/water medium. Secondly, the synthesis of the polysiloxane shell was carried out using a sol–gel process of MTMS. The thickness of the shells can be easily varied with different copolymer seeds and MTMS feed ratio. When we used copolymer particles with 2.00 μm diameter as seeds, the thickness of the polysiloxane shells can be varied from 0.10 to 0.18 μm. The core/shell structure of the composite microspheres was characterized by transmission electron microscope (TEM).     

Emulsion copolymerization of styrene with acrylic or methacrylic acids – distribution of the carboxylic group

Studies on batch emulsion copolymeization of styrene with acrylic acid (AA) or methacrylic acid (MAA) were carried out. The effect of AA or MAA on the total conversion of the monomers was studied by a gravimetric method. The distribution of the carboxylic group in the copolymer microspheres was investigated by X-ray photoelectron spectroscopy and elemental analysis. The surface content of the carboxylic groups of styrene (St)/AA copolymer microspheres was found to be higher than that of St/MAA copolymer microspheres. The effects of partial neutralization of MAA in emulsifier-free emulsion copolymerization and seeded emulsion copolymerization on the distribution of the carboxylic group was also investigated. Received: 14 December 1999/Accepted: 23 August 2000     

Design of polylactide-grafted copolymeric stabilizer for dispersion polymerization of D,L-lactide

Poly(D,L-lactide) (PDLLA) microspheres with narrow diameter distribution were prepared by dispersion polymerization of D,L-lactide in xylene/heptane (1:2, v/v) using poly(dodecyl methacrylate)-g-poly(D,L-lactide) (PDMA-g-PDLLA) as a dispersion stabilizer. The particle diameters of PDLLA microspheres were controlled from 200 nm to 5 μm by altering the concentration and the graft chain number of PDMA-g-PDLLA. The effect of the copolymer composition on the particle diameter was investigated to clarify an important factor of the copolymer structure for the control of the particle diameter. As a result, it was necessary for anchor block in diblock copolymer as a dispersion stabilizer to have low solubility in the solution rather than the compatibility with particles. Moreover, we confirmed by dynamic light scattering measurement that PDMA-g-PDLLA formed micelles in the solution. In conclusion, it was clarified that PDLLA microspheres with a wide range of particle diameter were prepared due to the different kinetic stability of micelles.     

Preparation of P4VP-g-PSt Copolymer Microspheres with Controllable Size by Atom Transfer Radical Polymerization Synthesized Poly(4-vinylpyridine) Macromonomer

Poly(4‐vinylpyridine) macromonomer (St‐P4VP) with a styryl end group was synthesized by atom transfer radical polymerization (ATRP) of 4‐vinylpyridine using p‐(chloromethyl)styrene (CMSt) as functional initiator, CuCl as catalyst and tris[2‐(dimethylamino)ethyl]amine (Me₆TREN) as ligand in 2‐propanol. The structure of St‐P4VP macromonomer was identified by proton nuclear magnetic resonance (¹H NMR). The result of gel permeation chromatography (GPC) illustrated that the number‐average molecular weight of St‐P4VP could be controlled by adjusting polymerization conditions. Poly(4‐vinylpyridine) grafted polystyrene microspheres (P4VP‐g‐PSt) were then prepared by dispersion copolymerization of styrene with St‐P4VP macromonomers. The effects of polymerization reaction parameters such as medium polarity, concentration of St‐P4VP macromonomer and polymerization temperature on the sizes and size distribution of P4VP‐g‐PSt microspheres were investigated. The results of transmission electron microscopy (TEM), scanning electron microscopy (SEM) and laser light scattering (LLS) indicated that mono‐dispersed P4VP‐g‐PSt microspheres with average diameters of 100–200 nm could be obtained when the molar ratio of St to St‐P4VP was 0.25:100 in ethanol/water mixed solvents (V/V=80:20) at 60°C. Such kind of graft copolymer microspheres was expected to be applied to many fields such as drug delivery system and protein adsorption/separation system due to their particular structure.     

Nonswellable and swellable ethylene glycol dimethacrylate-acrylic acid copolymer microspheres

In this study, nonswellable and swellable poly(ethylene glycol dimethacrylate/acrylic acid) copolymer microspheres, in the size range of 50–150 μm, were produced by conventional and modified suspension copolymerizations of the respective monomers, i.e., ethyleneglycol dimethacrylate (EGDMA) and acrylic acid (AA) in aqueous media. Poly(vinyl alcohol) and benzoyl peroxide were used as the stabilizer and the initiator. The diluent, i.e., toluene was included in the polymerization recipe of the modified suspension polymerization. The microspheres were characterized by optical microscopy, FTIR, and FTIR-DRS, and potentiometric titrations. Highly crosslinked, transparent, and nonswellable poly(EGDMA/AA) microspheres were obtained with the conventional suspension polymerization procedure. The modified suspension polymerization provided swellable, opaque, and crosslinked copolymer microspheres. Acrylic acid incorporation into the copolymeric microspheres were significantly higher in the modified procedure, relative to the conventional procedure. © 1996 John Wiley & Sons, Inc.     

Mechanism of dispersion polymerization of L-lactide initiated with 2,2-dibutyl-2-stanna-1,3-dioxepane

 Biodegradable polyester microspheres were synthesized directly by ring-opening polymerization of l-lactide initiated with 2,2-dibutyl-2-stanna-1,3-dioxepane. The polymerizations were carried out at 95 °C in a mixture of organic solvents (heptane/1,4–dioxane 4:1 v:v), in the presence of poly(dodecyl acrylate)-g-poly(ɛ-caprolactone) used as a surface-active agent. Under these conditions the poly(L-lactide) synthesized was shaped into microspheres. The absence of new particles in the polymerizations with multistep monomer addition indicated that after the formation of particle seeds the propagation proceeds exclusively inside the microspheres. The mean volume of these microspheres was proportional to the monomer conversion. It was found that regardless of the initiator concentration the average number of poly(L-lactide) macromolecules in one microsphere was 1.84 × 10⁸. Matrix-assisted laser desorption ionization time of flight spectroscopy of poly(L-lactide) in the microspheres indicated that the propagation in the particles was accompanied by intra- and intermolecular transesterification side reactions, resulting in reshuffling of the polymer segments and the formation of cyclic oligomers. Received: 20 December 2000 Accepted: 7 June 2001     

Preparation of monodisperse polystyrene microspheres: effect of reaction parameters on particle formation,and optical performances of its diffusive agent application

There are three monodisperse polystyrene (PSt) microspheres, 1.10, 3.13, and 5.21 um in diameter were prepared by dispersion polymerization in ethanol/iso-propanol media. 2,2′-azobis(isobutyronitrile) (AIBN) and poly(acrylic acid) (PAA) were utilized as initiator and steric stabilizer, respectively. The effects of the PAA stabilizer, AIBN initiator, St monomer, and EtOH solvent on particle size and size distribution were reviewed in this article. Besides, optical properties including total transmittance (T%) and transmittance haze (H%) were performed when these three monodisperse PSt microspheres were applied as diffusive agents. The results were examined in terms of total interface area in a system, and came up an optimal situation between transmittance haze (H _max% = 65%) and T% when total surface area of particles is around 45,000 cm².     

Effect of water-soluble cross-linker on the growth and properties of ethyl acrylate–methacrylic acid emulsion opolymer particles

Model ethyl acrylate–methacrylic acid copolymer latices and latices of particles cross-linked by copolymerizing small amounts of water-soluble N,N′-methylenebisacrylamide were prepared by nonseeded semicontinuous emulsion copolymerization. Dynamic and static light scattering measurements indicated a slightly higher degree of polydispersity in the case of cross-linked particles, especially in the initial stages of polymerization. The hydrodynamic volume of the alkalinized particles controlling the viscosity properties of the dispersions decreased with the time of polymerization and in the case of cross-linked copolymer almost reached a constant value at about 1 h. The different character of the particle structure was confirmed by differences in particle disintegration after alkali addition or in the presence of methanol. Received: 2 February 1999/Accepted: 28 June 2000     

Synthesis of cross-linked magnetic composite microspheres containing carboxyl groups

Fe₃O₄ magnetic nano-particles were prepared by a co-precipitation method and were modified using oleic acid. Then, the cross-linked magnetic compsoite microspheres containing a carboxyl group were prepared by using an improved emulsion polymerization with divinylbenzene (DVB) as the cross-linking agent. The composite microspheres comprised the Fe₃O₄ magnetic nano-particles as cores and the copolymer of styrene and acrylic acid as shells. The morphology and structure of the composite microsphere were characterized by FT-IR, transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectrum (XPS) and so on. The results show that the composite microspheres were well dispersed in emulsion with uniform sizes and carboxyl groups on their surface. They were cross-linked and stable in 1 mol/L of HCl and DMF. __________ Translated from Journal of Functional Polymers, 2007, 19–20(1): 27–32 [译自: 功能高分子学报]     

Potentiometric titration behavior of poly(acrylic acid) within a cross-linked polymer network having amide groups

This study aimed to investigate the effect of COOH group distribution within a polymer network having amide groups, with which the COOH could form hydrogen bonds. We employed here two polyelectrolyte gels composed of N-isopropylacrylamide (NIPA) networks, either copolymerized with acrylic acid (AA) or within which poly(acrylic acid) (PAA) was entrapped. Both gels (AA–NIPA ∼ 1:4 mol/mol) were prepared by aqueous red-ox polymerization with N,N’-methylenebisacrylamide as the cross-linker. Finely divided gels in NaCl solutions (0.025 and 0.1 M) were titrated with NaOH and back-titrated with HCl at 25 °C. The results of the copolymer gel (CG) agreed well with those of a linear copolymer and a nanoscale gel which had a similar AA content to CG. However, marked differences were observed in the titration behaviors of the AA-copolymerized and PAA-entrapped gels, mainly due to the hydrogen bonding between the entrapped PAA chain and its surrounding NIPA network.     

包覆Fe2O3超微粒的苯乙烯/丙烯酸/丙烯酸丁酯核-壳型复合共聚物的性能研究

对采用种子乳液聚合法合成的包覆Fe₂O₃超微粒的苯乙烯/丙烯酸/丙烯酸丁酯(St/AA/BA)核-壳型复合共聚物材料进行玻璃化温度测试,结果表明,加入Fe₂O₃超微粒,使复合共聚物的玻璃化温度显著降低.对复合共聚物的流变行为研究表明,复合共聚物的非牛顿指数均小于1,且随着Fe₂O₃含量增加,非牛顿性增强,表观粘度下降,粘流活化能降低.     

Cationic amino-containing N-isopropyl- acrylamide–styrene copolymer latex particles: 1-Particle size and morphology vs. polymerization process

 Cationic hydrophilic copolymer latexes were synthesized at 70 °C either by batch or two-step emulsifier-free emulsion poly-merization of styrene (St), N-iso-propylacrylamide (NIPAM), and aminoethylmethacrylate hydro-chloride (AEM) using 2,2′-azobis (2-amidinopropane) dihydrochloride as initiator. At first, batch polymerization kinetics were followed by gas chromatography (GC), revealing that NIPAM rapidly homopolymerized, before the polymerization of styrene had started. Particle size analysis by quasi-elastic light scattering (QELS) and transmission electron microscopy (TEM) showed that monodispersed particles were obtained with the formation of a poly[NIPAM] rich shell. Adding a small amount of the cationic monomer caused a strong decrease of the particle size without affecting the size monodispersity. When a shot process was used, a narrow particle size distribution was maintained, provided that the monomer addition was performed at a relatively high conversion of the first batch step. The poly[NIPAM] rich shell layer was larger with the shot process, but increasing the amino-containing monomer in the recipe resulted in a dramatic decrease of the thickness. Combination of transmission, scanning and atomic force microscopy techniques showed that these hydrophilic particles exhibited odd-shaped structures, the unevenness being dependent upon the performed process. Kinetic data and particle morphology information were inferred for discussion of the polymerization mechanism of this system. Received: 21 August 1997 Accepted: 22 October 1997     

Amphoteric initiators suitable for emulsifier-free emulsion polymerization and the properties of the resulting latices

The soap-free emulsion polymerizations of styrene (St) and acrylamide (AAm) or methyl methacrylate (MMA) were carried out in the presence of three kinds of amphoteric initiators, and the polymerization kinetics and the colloidal properties of the latices produced were emphatically investigated. It was found that the number of carbon atoms between the amidino and carboxyl groups in each initiator exhibited an appreciable effect on the dissociation as well as on the solubility of the initiator in water, and therefore, that the properties of the colloidal particles depended on the structure of the initiators used. All the copolymerization runs, except for the polymerization using 2,2′-azobis(N-(2-caboxyethyl)-2-methylpropionamidine) under a strongly alkali condition, gave amphoteric latices, which indicated higher critical flocculation concentrations at lower or higher pHs than at a medium pH. The surface charge density measured by titration for poly(St/MMA) particles was about 3–10 times as high as that for the poly(St/AAm) ones, though these were prepared under the same conditions other than the monomer composition. The influence of the polymerization pH on both the polymerization rate and the surface charge density of the resulting latices was negligible even if the constants of the decomposition rate and the dissociation of the amphoteric initiators strongly depended on the pH of the medium. Received: 28 July 2000 Accepted: 1 November 2000     

Investigation of stabilizer‐free dispersion polymerization process of styrene and maleic anhydride copolymer microspheres

The copolymer microspheres of styrene (St) and maleic anhydride (MA) were synthesized by stabilizer‐free dispersion polymerization, and the polymerization process was explored in detail. The results showed that the homopolymerization of St formed in initial polymerization period served as stabilizer, and reaction solvent of closer solubility parameter would benefit the stabilizer‐free dispersion polymerization. In addition, some principal factors affecting the microspheres size, such as reaction time, reaction temperature, monomer concentration, molar feed ratio, reaction media, and cosolvent, were investigated as well. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Preparation of biodegradable microspheres by anionic dispersion polymerization with PLA copolymeric dispersion stabilizer

We prepared poly(d,l-lactide) (PLA) microspheres by anionic dispersion polymerization of d,l-lactide. The polymerization was carried out in xylene/heptane (1:2 in v/v) mixture solution at 368 K for 9 h, with poly(dodecyl methacrylate)-co-poly[α-methacryloxyethoxy-poly(l-lactide)] (PDMA-co-P(MA-PLLA)) synthesized in this study, as a dispersion stabilizer. The number-averaged diameter and diameter distribution (coefficient of variation) of obtained PLA microspheres ranged from 180 to 800 nm and 14–40%, respectively, depending on the preparation condition. Furthermore, the time courses of monomer conversion, particle diameter, and particle number were investigated to clarify the formation mechanism of microspheres with PDMA-co-P(MA-PLLA) as a dispersion stabilizer. From this experiment, we found that the aggregation of primary particles occurred in anionic dispersion polymerization, and the particle diameter of obtained PLA microspheres decreased with increasing PDMA-co-P(MA-PLLA) concentration. In conclusion, we clarified that PDMA-co-P(MA-PLLA) effectively contributed to the stability of primary particles.     

控制自由基聚合制备Fe3O4/SiO2/P(AA-MMA-St)磁性复合微球

用原硅酸乙酯对Fe3O4纳米粒子进行表面改性得到Fe3O4/SiO2磁流体.在Fe3O4/SiO2磁流体存在下,以1,1-二苯基乙烯(DPE)为自由基聚合控制剂,利用乳液聚合法制备了Fe3O4/SiO2/P(AA-MMA-St)核-壳磁性复合微球.用红外光谱(FTIR)、振动样品磁强计(VSM)、透射电镜(TEM)、X光电子能谱(XPS)、热重分析(TGA)、示差扫描量热仪(DSC)对所制备的磁流体、磁性高分子复合微球的结构、形态、性能进行了表征.研究发现,原硅酸乙酯水解后能在Fe3O4表面形成硅膜保护层从而避免Fe3O4的酸蚀,使Fe3O4/SiO2/P(AA-MMA-St)复合微球的比饱和磁化强度比同样条件下制备的Fe3O4/P(AA-MMA-St)微球提高了28%;DPE能有效控制自由基在Fe3O4/SiO2磁流体表面均匀地引发单体聚合,得到平均粒径为422 nm,无机粒子含量为40%,比饱和磁化强度为34.850 emu/g,表面羧基含量为0.176 mmol/g的磁性复合微球.