Growth and characterization of photorefractive Bi12TiO20 single crystals

Photorefractive Bi₁₂TiO₂₀ single crystals of high optical quality were grown in a resistive heating furnace from high temperature nonstoichiometric (10:1) solutions of Bi₂O₃ and TiO₂ at pulling rates 0.3–0.8 mm/h at rotation 20–30 rpm along the <001> and <011> axis. Powder X-ray analysis, Laue method, and electron-probe microanalysis were used for characterization. BTO crystals have the bcc structure of sillenite type with a₀ = 10.178(8) Å. The chemical composition of the crystals can be written down as Bi_{12.1 ± 0.2}Tio_{0.96 ± 0.09}O_20.1. Natural optical activity ρ of BTO crystals is 6.3 ± 0.2 deg/mm at λ = 0.633 μm and 11.9 ± 0.2 deg/mm at λ = 0.5145 μm, optical absorption coefficient α = 0.42 ± 0.04 cm⁻¹ at λ = 0.633 μm and linear electro-optic coefficient r₄₁ = r₅₂ = r₆₃ = 5.3 pm/V. Fanning effect in the “fiber-like” BTO sample was studied and double phase conjugation with conversion efficiency up to 8% was observed in a wide range of incidence angles of the pump at λ = 0.633 μm for 2 × 3 mW input light power.     

Single‐crystal growth and characterization of mullite‐type orthorhombic Bi2M4O9 (M = Al3+, Ga3+, Fe3+)

Pure and homogeneous single crystals of orthorhombic mullite‐type Bi₂M₄O₉ (M = Al³⁺, Ga³⁺, Fe³⁺), and a mixed Bi₂Fe_1.7Ga_2.3O₉ crystal from an equimolar Ga/Fe composition were grown by the top seeded solution growth (TSSG) method. All these compounds melt incongruently in the range of about 800 and 1100 °C. In case of bismuth gallate and ferrate inclusion‐free crystals with dimensions up to several cubic centimeters can be grown. Limited solubility in Bi₂O₃ and the high steepness of the liquidus curve are the reasons for getting only small imperfect bismuth aluminate crystals. In contrast to ceramic materials preparation reported in literature, divalent calcium and strontium could not be incorporated into the mullite‐type structure during the melt growth process. Several fundamental physical properties like heat capacity, thermal expansion, heat conductivity, elastic constants, high‐pressure behavior and oxygen diffusivity were determined by different research groups using single‐crystalline samples from the as‐grown materials. Furthermore, the refractive indices of Bi₂Ga₄O₉ were measured in the range of 0.430 and 0.700 μm. Such as many other bismuth containing compounds the refractive indices of Bi₂Ga₄O₉ are larger than 2, and Bi₂Ga₄O₉ is an optic biaxial positive crystal. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Fluorescence properties of Nd3+ doped stoichiometric LiNbO3 fiber single crystals by micro‐pulling down method

Using the micro‐pulling down (μ‐PD) method, 1 and 3 mol% Nd₂O₃ doped near stoichiometric lithium niobate (LiNbO₃) single crystal fibers were grown in 1 mm diameter and 35∼40 mm length. The grown crystal fibers were free of cracks and the homogeneous distribution of Nd³⁺ ion concentrations were confirmed by the electron probe micro analysis. The changes of fluorescence spectra were measured with respect to the Nd³⁺ ion doping concentration. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

On the Iso‐Diameter Growth of β ‐BaB2O4 (BBO) Crystals by Flux Pulling Method

The iso‐diameter growth of β ‐BaB₂O₄ (BBO) crystals by the flux pulling method have been studied based on the phase equilibrium diagram in the BaB₂O₄‐Na₂O pseudo‐binary system and from the interface stability. The mathematical expressions for the cooling rate in the growth of the crystals with constant diameter under stable growth conditions are derived, the experimental phenomena such as diameter contraction and difficulty to grow a lengthy crystal by the flux pulling method are explained, the prerequisite for iso‐diameter BBO crystal growth from the flux is suggested; a new continuous charging flux pulling method is introduced to grow large‐sized high quality crystals with a relative high growth rate.     

Improved Single Crystal Growth of the Boron Sillenite “Bi24B2O39” and Investigation of the Crystal Structure

The boron sillenite, up to now known as the 12:1 compound Bi₂₄B₂O₃₉ in the system Bi₂O₃ – B₂O₃ andcrystallizing in the space group I23, melts incongruently at 655 °C only about 25 K above the eutectic tie line and corresponding to a steep liquidus line. Single crystals with dimensions larger then 1 cm ³ have been successfully grown in [100], [110], and [111] direction by an improved Top Seeded Solution Growth (TSSG) technique equipped with crucible weighing, accelerated crystal rotation technique and air‐cooled pulling rod. The structure of the boron sillenite was analyzed by X‐ray diffraction method, which was possible due to the high crystalline quality achieved. A defect‐free sublattice corresponding to a Bi‐O framework is isostructural with all sillenites, but a 2 Å environment around the origin is occupied by different cations with different population coefficients. The best calculation results in the formula Bi_24.5BO_38.25 which is more Bi‐rich than the 12:1 assumption.     

Crystal growth and scintillating properties of (Pr,Si)‐doped YAlO3

This paper deals with Pr‐doped and Pr, Si‐codoped YAlO₃ single crystal growth by the micro‐pulling‐down method and investigation of their spectroscopic and scintillating properties. The Pr³⁺ 5d ‐4f radioluminescence intensity is more than 10 times higher than that of Bi₄Ge₃O₁₂ standard sample, but the Si‐codoping decreases it. Absorption spectra of as‐grown and air‐annealed Si,Pr‐codoped YAlO₃ samples show along with an onset of 4f ‐5d transition round 230 nm the induced absorption band at 400 nm which possibly related to a hole center absorption (Pr⁴⁺ or O^‐). Thermoluminescence measurements above the room temperature were performed in order to monitor deep electron traps. Strong concentration dependence of thermoluminescence was observed for Pr:YAlO₃ glow curves. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal growth,optical and luminescence properties of (Ce,Sr)‐doped PrAlO3 single crystals

Using the micro‐pulling‐down method, (Ce,Sr)‐doped PrAlO₃ square‐shaped single crystals (4×4×12 mm) were grown. Structural parameters studied by X‐ray powder diffraction were consistent with R3m space group. Compositional homogeneity was checked with electron probe micro‐analysis and found quite uniform. Absorption spectra and luminescence characteristics under UV and X‐ray excitations were measured at room temperature with no Ce‐related emission appeared. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Flux growth and characterization of Ti‐ and Ni‐doped forsterite single crystals

Forsterite monocrystals doped with Ti and Ni were grown by the flux growth technique. A suitable mixture of flux (MoO₃, V₂O₅, Li₂CO₃) and nutrient was slowly cooled down to 750 °C from 1250 °C or 1350 °C. The crystals were then characterized by powder and single‐crystal X‐ray diffraction, scanning electron microscopy and differential scanning calorimetry (DSC). Variations observed in crystal size were attributed by both the varying experimental conditions in which they had been obtained, and to the amount of Ni substituted for Mg in the structure. High abundances of doped forsterite required a cooling rate of 1.8 K h^‐1. These synthetic, well‐characterized Ti and Ni doped forsterite crystals may have potential for exploitation in industrial fields. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Substitution effects on ferroelectric,leakage current and anti‐fatigue characteristic of Bi4‐xSbxTi3O12 thin films

Bi_4‐xSb_xTi₃O₁₂ (BSTO) (x = 0, 0.03, 0.04, 0.05, 0.06 and 0.07) thin films have been fabricated on Pt/Ti/SiO₂/Si substrates by sol‐gel method. The effects of various Sb³⁺ content on microstructure and ferroelectric properties of systems are investigated. XRD show that Bi_4‐xSb_xTi₃O₁₂ (x≠0) thin films prefer (117) orientation. The substitution Sb³⁺ for Bi³⁺ reduces the grain size of the film surface. Compared to the BTO (x = 0) film, Bi_4‐xSb_xTi₃O₁₂ films display exciting electric properties. Especially when x = 0.04, the film Bi_3.96Sb_0.04Ti₃O₁₂ has achieved the max 2Pr value of 87μC/cm². This film also has a better anti‐fatigue characteristic, which can be up to 10¹⁰ switching cycles without fatigue. The leakage current density improved with J = 8×10⁻⁸ A/cm².     

Micro‐Pulling Down Growth of Co‐doped Lithium Niobate Single Crystal Fibers According Er and Mg Contents and Photolumenescence Properties

The Er³⁺doped Mg:LiNbO₃single crystal fibers employed in our experiment were grown in air by a micro‐pulling down (μ‐PD) method from host materials of a congruent Li/Nb (0.945) ratio which were melt‐doped with a nominal molar concentration of 1, 3, 5% MgO and 0.6% Er₂O₃. The X‐ray diffraction analysis results indicated that the co‐doped crystals main tained the same structural characteristics as the undoped LiNbO₃, however the lattice parameters with Mg differed; c (Å) value decreased, and a (Å) increased than of pure LiNbO₃. The influence of dopants on the photoluminescence (PL) properties of the Er:Mg:LiNbO₃ single crystal fibers excited by laser lines of 514 nm was reported. Also, the PL properties according to temperature and the excitation power of Er:Mg:LiNbO₃ crystal fibers were analyzed.     

Growth,structure, and superconducting properties of Bi2Sr2Ca2Cu3O10 and (Bi,Pb)2Sr2Ca2Cu3O10‐y crystals

Large and high‐quality single crystals of both Pb‐free and Pb‐doped high temperature superconducting compounds (Bi_1‐xPb_x)₂Sr₂Ca₂Cu₃O_10‐y (x = 0 and 0.3) were grown by means of a newly developed “Vapour‐Assisted Travelling Floating Zone” technique (VA‐TSFZ). This modified zone‐melting technique was realised in an image furnace and allowed for the first time to grow Pb‐doped crystals by compensating for the Pb losses occurring at high temperature. Crystals up to 3×2×0.1 mm³ were successfully grown. Post‐annealing under high pressure of O₂ (up to 10 MPa at T = 500°C) was undertaken to enhance T_c and improve the homogeneity of the crystals. Structural characterisation was performed by single‐crystal X‐ray diffraction (XRD) and the structure of the 3‐layer Bi‐based superconducting compound was refined for the first time. Structure refinement showed an incommensurate superlattice in the Pb‐free crystals. The space group is orthorhombic, A2aa, with cell parameters a = 27.105(4) Å, b = 5.4133(6) Å and c = 37.009(7) Å. Superconducting studies were carried out by A.C. and D.C. magnetic measurements. Very sharp superconducting transitions were obtained in both kinds of crystals (ΔT_c ≤ 1 K). In optimally doped Pb‐free crystals, critical temperatures up to 111 K were measured. Magnetic critical current densities of 2�10⁵ A/cm² were measured at T = 30 K and μ₀H = 0 T. A weak second peak in the magnetisation loops was observed in the temperature range 40‐50 K above which the vortex lattice becomes entangled. We have measured a portion of the irreversibility line (0.1‐5 Tesla) and fitted the expression for the melting of a vortex glass in a 2D fluctuation regime to the experimental data. Measurements of the lower critical field allowed to obtain the dependence of the penetration depth on temperature: the linear dependence of λ(T) for T < 30 K is consistent with d‐wave superconductivity in Bi‐2223. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and crystal growth of sillenite phases in the Bi2O3 ‐ TiO2 ‐ Nb2O5 system

The synthesis of Bi₂O₃‐Nb₂O₅ sillenite phase (BNbO) and the solubility of this phase with Bi₁₂TiO₂₀ was investigated by solid‐state reaction synthesis and niobium doped Bi₁₂TiO₂₀ (BTO:Nb) crystals were grown by the Top Seeded Solution Growth (TSSG) technique. The structures of polycrystalline compounds were checked by X‐ray powder diffraction method at room temperature. The correct composition of the sillenite phase stabilized with niobium was determined as Bi₁₂[Nb_0.17Bi_0.83]O_19.7 (BNbO) with unit cell parameter a = 10.261(2) Å. The system BTO‐BNbO is poorly soluble, but niobium doped BTO crystals were grown from the liquid composition 10Bi₂O₃ : xTiO₂ : (1‐x)/2 Nb₂O₅, with x = 0.95 and 0.90. A niobium concentration limit in the liquid phase is established in order to grow BTO:Nb with good crystalline quality. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Infrared and Raman spectroscopy of mullite‐type Bi2Ga4O9

Mullite‐type Bi₂Ga₄O₉ single‐crystals were grown by the top‐seeded solution growth (TSSG) method and investigated by vibrational spectroscopy. Polarised IR specular reflectance and attenuated total reflectance (ATR) spectra, as well as polarised micro‐Raman spectra were acquired at room temperature. Powder IR spectra of sol‐gel‐derived samples were also recorded. Using model calculations and comparison to other mullite‐type compounds, bands at ∼ 850 – 400 cm^‐1 could be assigned to stretching and bending vibrations of the structural GaO₄ and GaO₆ units. Low‐energetic modes were attributed to motions involving Bi atoms. The IR spectra of Bi₂Ga₄O₉ display close similarities to those of the mullite‐type alkali gallates (9Ga₂O₃ · Rb₂O), while their differences to those of mullite sensu stricto (3Al₂O₃ · 2SiO₂ and 2Al₂O₃ · SiO₂, repectively) are assigned to Si‐O stretching vibrations of the corresponding tetrahedral units. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Flux growth of straw‐like rutile monocrystals

Millimetric straw‐like rutile monocrystals were grown by the flux growth technique. A suitable mixture of flux (MoO₃, V₂O₅, Li₂CO₃) and amorphous TiO₂ gel was slowly cooled down to 750°C from 1250°C or 1350°C. The best yields of straw‐like rutile were obtained with a nutrient/flux ratio and a cooling rate in the range 0.015‐0.006 and 1.8‐1.9 K h^‐1, respectively. The hollowed crystals were characterized by powder and single‐crystal X‐ray diffraction, scanning electron microscopy, microthermometry, and µ‐Raman spectroscopy. As for skeletal crystal, the formation of axial canals in rutile is attributed to a lack of nutrient due to the viscosity of the melt and the high growth rate along [001]. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Near‐stoichiometric LiNbO3:ZrO2 single crystal growth by micro pulling down method

Crack‐free, rod‐shaped single crystals of undoped and 0.5, 0.7 and 1.0 mol% ZrO₂‐doped LiNbO₃ with a near‐stoichiometric composition were grown by the micro‐pulling down (μ‐PD) method. The structural properties of the grown crystals were examined by powder X‐ray diffraction (XRD). Electron probe micro analysis (EPMA) of the near‐stoichiometric LiNbO₃ single crystals revealed the homogeneous incorporation of Zr ions. The change in the refractive index and IR transmission spectra of the grown crystals were examined as a function of the Zr concentration. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Characterization of dislocations in a LiNbO3 single crystal grown by micro pulling down method

LiNbO₃ single crystals grown by the micro pulling down (μ-PD) method have been revealed to be as free of dislocations and subgrain boundaries up to 500 μm in diameter. On the other hand, μ-PD LiNbO₃ single crystals grown along the x-axis in diameter of 800 μm were observed to be dislocated due to the size effect of crystal. The Burgers vectors of dislocations were determined to be [22 01], [101 1], and [01 11] by X-ray topography.     

A new nonlinear optical crystal: Bi2O2(OH)(NO3)

The nonlinear optical (NLO) properties of Bi₂O₂(OH)(NO₃) crystals have been reported for the first time. Bi₂O₂(OH)(NO₃) crystals with dimensions of 1.3×1.2×0.1 mm³ have been grown by hydrothermal method, and the crystals characterized by X‐ray powder diffraction (XRD), SEM and IR. The measured second harmonic generation (SHG) effect of Bi₂O₂(OH)(NO₃) was about 7 times that of KDP. The mechanism responsible for the large SHG of Bi₂O₂(OH)(NO₃) was explained according to its structure. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High‐temperature infrared and dielectric properties of large sapphire crystal for seeker dome application

In this paper, large‐sized (∅︁230 mm × 210 mm, 27.5 kg) sapphire was successfully grown by SAPMAC (sapphire growth technique with micro‐pulling and shoulder‐expanding at cooled center) method; and hemisphere dome (140 mm diameter, 5 mm thickness) was fabricated from as‐grown boule. Also, its high temperature infrared transmission (2∼7 µm, 20–800°C) and microwave dielectric properties (8–16.5 GHz, 30–1300°C) were investigated. The experimental results show that sapphire crystal exhibits high infrared transmittance (3 μm, 80–86%), essentially negligible dielectric loss (4.9×10^‐5–3.7×10^‐4), but fairly high dielectric constants (ε=9.4–12.5) in the temperature range of 30–1300°C. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical properties of non‐centrosymmetric mixed crystals K2(La1‐x Cex)(NO3)5 · 2 H2O (x = 0.0 – 1.0)

Large single crystals of optical quality of the non‐centrosymmetric orthorhombic potassium rare earth nitrate mixed crystals K₂(La_1–x Ce_x)(NO₃)₅ · 2 H₂O were grown at 38 °C from diluted HNO₃. For crystals with x = 0.0, 0.19, 0.38 and 0.66 refractive indices and their dispersion were determined with an error less than 1 · 10^–4 in the wavelength range 0.404 – 1.083 μm by the prism method. Phase matching conditions for collinear SHG frequency conversion were analysed in detail, including calculation of the effective nonlinear optical susceptibility. By an appropriate choice of the fraction x of cerium the mixed crystals K₂(La_1–x Ce_x)(NO₃)₅ · 2 H₂O allow an adjustment of non‐critical type I phase matching conditions to a desired wavelength of the fundamental wave within the range 1.055(4) – 1.107(6) μm. Non‐critical type II phase matching can be tuned in the wavelength range 0.949(2) – 0.931(2) μm. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Crystal Structure of Diethyl 2‐[2,2,2‐ trifluoro‐1‐(indole‐3‐yl)‐ethyl]‐2‐acetamidomalonate

The title compound (C₁₉H₂₁F₃N₂O₅) has been determined from three dimensional X‐ray diffraction data. The crystals are monoclinic, a = 7.626(4)Å, b = 17.515(4)Å, c = 15.066(3)Å, β = 101.02(3)°, V = 1975(1)ų, Z = 4, D_calc = 1.393g cm^‐3, space group P2₁/c. The structure was solved by direct methods and refined by full‐matrix least‐squares method (R = 0.039).