Czochralski Growth of Potassium Lithium Niobate Single Crystals with Low Li Content and Their Characterization

Single crystalline and crack free potassium lithium niobate (KLN) single crystals with low Li content were grown by the Czochralski method. The crystal composition can be written as K_2.60Li_1.17Nb_5.44O₁₅ (=K_2.95Li_1.33Nb_6.17O₁₇) which contain relatively fewer Li ions than ferroelectric K₃Li₂Nb₅O₁₅ crystals. All experimental results show that the deficiency of the Li ions in the KLN crystals strongly influences their physical properties. Especially, the as‐grown crystals do not indicate any signature for a ferroelectric phase transition in contrast to the ferroelectric K₃Li₂Nb₅O₁₅ crystals. However, due to ionic conduction, the temperature dependence of the dielectric constant of such KLN‐2 crystals show a broad anomaly near 300°C. In addition, the existence of proton defects can be revealed by infrared absorption spectroscopy near 3500 cm^‐1 in as‐grown crystals.     

Influence of the temperature and the oxygen partial pressure on the phase formation in the system Cu – Fe – O

Copper iron oxides, Cu_1‐xFe_2+xO₄ (0 ≤ x ≤ 0.5), have been synthesized by thermal oxidation of copper ‐ iron mixtures. In this process, the phase formation and the phase stability were investigated as function of the temperature (800°C – 1200°C) and the oxygen partial pressure (1.013 x 10¹ – 1.013 x 10⁵ Pa). The phase formation starts with the reaction of the metallic components to simple oxides (Fe₃O₄, Fe₂O₃, CuO). From these simple oxides, the formation of complex oxides requires a minimum temperature of 800°C. The synthesis of single phase spinel compounds Cu²⁺_1‐2x Cu¹⁺_xFe_2+xO_4±δ is realized for 0.1 ≤ x ≤ 0.5, using specific temperature – p(O₂) – conditions for a given value of x. Remarkably, to achieve our goal, we found that the increase of x implies that of the reaction temperature and/or a decrease of the p(O₂) in the reaction gas stream. Besides, a single phase spinel CuFe₂O₄ does not exist in the temperature / p(O₂)‐field investigated. Using the results of XRD ‐ phase analysis, T ‐ p(O₂) – x – diagrams were constructed. These diagrams allow the prediction of phase compositions expected for different synthesis conditions. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Czochralski growth and constitutional studies on single crystals of potassium lithium niobate (KLN)

The ferroelectric phase of potassium lithium niobate K₃Li_2−xNb_5+xO₁₅ (KLN) is a very promising material for the conversion of infrared light to light in the visible region. However, growing of single crystals is known to be complicated due to the considerable anisotropy of the growth rate and the thermal expansion behaviour. The single crystals of KLN, Mg²⁺‐doped KLN, as well as the mixed crystals of potassium lithium tantalate niobate K₃Li₂(Nb_1−xTa_x)₅O₁₅ (KLTN) were grown by the Czochralski technique. The chemical analyses of the samples were performed by atomic absorption spectroscopy (AAS) and X‐ray fluorescence analysis (XRF). The element concentrations along the single crystals were measured by the electron microprobe analysis (EMPA) to clarify the segregation phenomena in the grown crystals. The elements distribution coefficients were also calculated. (© 2003 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of big single crystals of Sr2YRu1‐xCuxO6 from high temperature solutions

Single crystals of Sr₂YRu_1‐xCu_xO₆ (x = 0 ‐ 0.4) have been grown from PbO‐PbF₂ based solutions in the temperature range 1150 – 1350°C. A silicon carbide heating element furnace (with a recrystallized alumina tube lining) in a vertical configuration was used to grow the crystals in platinum crucibles. Conditions for the stable growth of big crystals have been investigated. The morphology of the crystals containing Cu was found to change from octahedral to cube octahedral as the growth temperature is increased from 1150 to 1350°C. Crystals measuring up to 4.5 mm across and 2.5 mm thick have been grown from 1250°C. The incorporation of Cu into the crystals was ascertained by EDS and x‐ray diffraction analysis. A diamagnetic transition which increased in magnitude and temperature with x was observed. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structural properties of Zn1–xMgxO nanomaterials prepared by sol‐gel method

The mixed oxides Zn_1‐xMg_xO (ZMO) were prepared as nano‐polycrystalline powders and thin films by a simple sol–gel process and dip coating method. Thermogravimetric (TG) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structural and microstructural analysis was carried out applying x‐ray diffraction (XRD) and Rietveld method. Analysis showed that for x < 0.25, Mg replaces Zn substitutionally yielding ZMO single phase, while for x ≥ 0.25 two phases are identified ZMO and MgO. Replacing Zn²⁺ by Mg²⁺ distorts the cation tetrahedrons and decreases the lattice constants ratio c/a of the wurtzite ZMO which deviate the lattice gradually from the hexagonal structure as Mg⁺² increases. These distortions are attributed to the difference in electronic configuration of the two cations which suppress the paraelectric‐ferroelectric phase transition in the ZMO wurtzite. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth of big single crystals of a new magnetic superconducting double perovskite Ba2PrRu1–xCuxO6

Single crystals of Ba₂PrRu_1–xCu_xO₆ with x = 0 to 0.2, have been grown from high temperature solutions of a mixture of PbO‐PbF₂ in the temperature range 1100–1200 °C. Thin crystals with mostly a hexagonal and triangular plate like habit measuring up to 1–2 mm across and 0.1–0.2 mm thick were obtained. The size, quality and morphology of the crystals were improved by varying the solution volume as well as additives like B₂O₃. Large crystals measuring up to 3 mm across and 0.3 to 0.5 mm thick were obtained with 5–7 wt% solute concentration and 0.51 wt% of B₂O₃. The ZFC curves exhibit a spin glass like behavior with x = 0 and a superconducting transition at 8 to 11 K depending on x = 0.05 to 0.1. The transition was also influenced by the growth temperature and post growth annealing. Powder x‐ray diffraction, EDS and Raman spectroscopic measurements confirm the presence of Cu in the crystals. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

The relations of sintering conditions and microstructures of [Bi0.5(Na1‐x‐yKxLiy)0.5]TiO3 piezoelectric ceramics

Bismuth sodium titanate (abbreviated as BNT) based solid solution, [Bi_0.5(Na_1‐x‐yK_xLi_y)_0.5]TiO₃ (0 < x + y < 1) ceramics, was invented in our group. These ceramics, which are considered as new candidates for lead‐free piezoelectric materials, were prepared by conventional ceramic sintering technique. The results of X‐ray diffraction show that the ceramics possess a single perovskite phase. The relations of the sintering conditions and the microstructures of the ceramics were studied. It was found that the optimized sintering condition is at 1100‐1150 °C for 2‐3 h, the grains of the ceramics have very regular shape, and the grain size of the ceramics is in the range of 1.3‐2.2 μm. These ceramics with the compositions of high amount of K⁺ and low amount of Li⁺ have relatively large piezoelectric charge constant (d₃₃), and can be put into practical applications. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Laser heated pedestal growth of potassium lithium niobate for UV generation

Potassium lithium niobate (KLN) is a nonlinear optical material with a high nonlinearity. It has the potential to improve the performance and reduce the cost of blue and UV lasers. KLN crystals are not commercially viable because growth by traditional techniques is not possible. In an effort to develop commercially viable KLN, single crystals of the material were grown by the laser heated pedestal growth method (LHPG) with compositions of x=0.02, 0.06 and 0.2 following K₃Li_2?xNb_5+xO_15+2x. Noncritical phase matching at 20 °C for previously unreported compositions of x=0.02 and 0.06 was measured at 795 nm and 805 nm, respectively. Overall, the results suggest that single crystal KLN can be used for SHG into the UV region of the spectrum and can be developed into a commercially viable nonlinear optical material.     

Growth and characterization of superconductive Nd2‐xCexCuO4‐y single crystals

Nd_2‐xCe_xCuO_4‐y single crystals with different x values have been successfully grown by Traveling Solvent Floating Zone method (TSFZ). Electronic properties of Nd_2‐xCe_xCuO_4‐y single crystals with various x have been studied in detail. The results show that superconductivity can be found in crystals with x > 0.1 (0.13‐0.18) directly grown at oxygen‐reduced atmosphere without post‐annealed, while no superconductivity appears in crystals with x < 0.1 at the same atmosphere. It is also found that, the segregation coefficient of Ce is determined to be 0.946 and transition temperature Tc (onset) reaches maximum value of 23.5 K at nominal composition x = 0.165. With further increase of Ce concentration, transition temperature of single crystals declines due to the precipitation of secondary Phases. In addition, the variation of lattice constants of Nd_2‐xCe_xCuO_4‐y single crystals with different x is also given. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and properties of zirconium-doped RbTiOPO<Subscript>4</Subscript> single crystals

Single crystals of the solid solutions RbTi_{1 ? x} Zr _x OPO₄ (0.015 < x < 0.034) were grown and their physical properties were studied. In the presence of zirconium in the crystals with the maximum content x = 0.034, the ferroelectric phase transition and the high-temperature transition from the orthorhombic to the cubic phase are shifted to lower temperatures by 100 and 50°C, respectively. In the temperature range from 700°C to room temperature, the conductivity of doped crystals decreases compared to that of the undoped crystals. It is of particular interest that the intensity of the second-harmonic generation of the doped crystals is substantially higher than that of RbTiOPO₄.     

Sequence of phase transitions in PbHfO<Subscript>3</Subscript>

The temperature changes in the PbHfO₃ structure in the temperature range of 20 < t < 400°C have been studied by X-ray powder diffraction. The sequence of phase changes with an increase in temperature was found to be as follows: orthorhombic phase Pbam (O1), orthorhombic phase C2mm (O2), tetragonal phase P4mm (T), and cubic phase Pm3m (C). The C2mm and P4mm phases are ferroelectric, which is confirmed by measuring the dependences ɛ(t). The similarity of the transition pattern obtained with the known transition sequences for ferroelectric (barium titanate, potassium niobate, and lead titanate) and antiferroelectric (lead zirconate) oxides is analyzed.     

Synthesis and characterization of compounds LixMn1+xFe2–2xO4 with spinel structure in the quasiternary system “LiO0,5 – MnOx – FeOx“

The thermal decomposition of freeze‐dried Li‐Mn(II)‐Fe(III)‐formate precursors was investigated by means of DTA, TG and mass spectroscopy. By the thermal treatment of the prefired precursors between 400 and 1000°C, single phase solid solutions Li_xMn_1+xFe_2–2xO₄ (0 ≤ x ≤ 1) with cubic spinel structure were obtained. To get single phase spinels, special conditions concerning the temperature T and the oxygen partial pressure p(O₂) during the synthesis are required. Because of the high reactivity of the freeze‐dried precursors, in comparison with the conventional solid state reaction, the reaction temperature can be lowered by 200°C. The cation distribution and the properties of the Li‐Mn‐ferrites were studied by chemical analysis, X‐ray powder diffraction and magnetization measurements. It was found that for high substitution rates, almost all lithium occupies the tetrahedral coordinated A‐sites of the spinel lattice AB₂O₄, while at small x‐values, lithium ions are distributed over the tetrahedral and octahedral sites. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of Ba ions substitution on multiferroic properties of BiFeO3 perovskite

Dielectric, magnetic and ferroelectric properties of Bi_1‐xBa_xFeO₃(x = 0.1, 0.2 and 0.3) synthesized by solid state reaction method are reported. X‐ray diffraction pattern showed that Bi_1‐xBa_xFeO₃was single phase. Ba substitution has led to a decrease in grain size and hence an increase in the electrical resistivity. The variation of dielectric constant and loss has been studied over a frequency range of 1 kHz – 2 MHz at room temperature. Ba doping leads to effective suppression of the spiral spin structure of BiFeO₃, resulting in the appearance of net magnetization. Improved multiferroic properties of Bi_0.8Ba_0.2FeO₃ ceramic with remnant magnetization and polarization 0.093 emu/g and 0.808 µC/cm², respectively, were obtained. The evidence of ferromagnetism and ferroelectric hysteresis loops in Bi_1‐xBa_xFeO₃system at room temperature makes it a good candidate for potential applications. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Study on K(DxH1‐x)2PO4 Crystals: Growth Habit,Optical Properties and their Improvement by Thermal‐Conditioning

Phosphite, which often exists in growth solutions obtained directly from commercial P₂O₅ , was found to have significant inhibiting effects on the growth of pyramidal face of KDP crystals. K(D_xH_1‐x)₂PO₄ (referred to as DKDP) crystals with different deuterium fraction x were grown and the optical performances were investigated. The absorption coefficients at 1.05 μm decreases monotonically with the increase of x. The transmission threshold shift from 1.65μm at x=0 to 2.10 μm at x=0.96. The high temperature phase transition temperature and latent heat were measured using the method of differential scanning calorimetry (DSC). Thermal conditioning experiments were carried out at 180°C and 140°C for KDP and DKDP, respectively. After conditioning, a different degree of improvement was observed in the optical homogeneity of the samples, while the laser damage threshold and light absorption coefficient showed no significant change.     

Relaxation of polaronic charge carriers in lithium manganese spinels

Lithium manganese spinels Li_1+xMn_2−xO₄, 0 ⩽ x ⩽ 0.33, were prepared by wet chemistry technique followed by heat-treatment at 750 °C or 800 °C. Differential scanning calorimetry was used to reveal phase transitions. Electrical properties were studied by impedance spectroscopy. LiMn₂O₄ exhibited phase transition below room temperature. The transition, seen as an exothermic event in DSC and a steep decrease of conductivity upon cooling, was sharp in sample sintered at 800 °C and broadened over a range of temperature in sample sintered at 750 °C. In the low temperature phase of LiMn₂O₄, two relaxations of similar strength were observed in the frequency dependent permittivity. The low frequency process was identified as relaxation of charge carriers since the relaxation frequency followed the same temperature dependence as the dc conductivity. The high frequency process exhibited milder temperature dependence and was attributed to dipolar relaxation in the charge-ordered structure. The dipolar relaxation was barely visible in Li substituted samples, x ⩾ 0.05, which did not undergo structural phases transition. Measurements extended to liquid nitrogen temperature showed gradual lowering of the activation energy of conductivity and relaxation frequencies, behavior typical for phonon-assisted hopping of small polarons.     

Properties of AgGa1‐xInxSe2 single crystals grown by Bridgman method

High‐pure and single‐phase AgGa_1‐xIn_xSe₂ (x=0.2) polycrystalline was synthesized by the mechanical and temperature oscillation method. Adopting the modified Bridgman method an integral AgGa_1‐xIn_xSe₂ single crystal with diameter of 14 mm and length of 35 mm has been obtained at the rate of 6 mm/day. It was found that there is a new cleavage face which was (101), and observed the four order X‐ray spectrum of the {101} faces. By the method of DSC analysis the melting and freezing points of the AgGa_1‐xIn_xSe₂ (x=0.2) single crystal were about 828°C and 790°C. The transmission spectra of the AgGa_1‐xIn_xSe₂ (x=0.2) sample of 5×6×2 mm³ were obtained by means of UV and IR spectrophotometer. The limiting frequency was 774.316nm and the band gap was 1.6eV. It can be found in the infrared spectrum that the infrared transmission was above 60% from 4000cm^‐1 to 600cm^‐1. The value of α in 5.3µm and 10.6µm were 0.022cm^‐1 and 0.1cm^‐1 respectively. All results showed that the crystal was of good quality. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microwave dielectric properties of La(1‐2x/3)Bax(Mg0.5Sn0.5)O3 ceramics

This study examined the potential applications of microwave dielectric properties of La_(1‐2x/3)Ba_x(Mg_0.5Sn_0.5)O₃ ceramics in rectenna. The La_(1‐2x/3)Ba_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid‐state method with various sintering temperatures. An apparent density of 6.62 g/cm³, a dielectric constant of 20.3, a quality factor of 51,700 GHz, and a temperature coefficient of resonant frequency of ‐78.2 ppm/K were obtained for La_2.98/3Ba_0.01(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effects of annealing on structural,electrical and optical properties of AgGa(Se0.5S0.5)2 thin films deposited by using sintered stoichometric powder

The structural, electrical and optical properties of AgGa(Se_0.5S_0.5 )₂ thin films deposited by using the thermal evaporation method have been investigated as a function of annealing in the temperature range of 450–600 °C. X‐ray diffraction (XRD) analysis showed that the structural transformation from amorphous to polycrystalline structure started at 450 ^oC with mixed binary phases of Ga₂Se₃, Ga₂S₃, ternary phase of AgGaS₂ and single phase of S. The compositional analysis with the energy dispersive X‐ray analysis (EDXA) revealed that the as‐grown film has different elemental composition with the percentage values of Ag, Ga, Se and S being 5.58, 27.76, 13.84 and 52.82 % than the evaporation source powder, and the detailed information about the stoichometry and the segregation mechanisms of the constituent elements in the structure have been obtained. The optical band gap values as a function of annealing temperature were calculated as 2.68, 2.85, 2.82, 2.83, and 2.81 eV for as‐grown, annealed at 450, 500, 550, and 600 °C samples, respectively. It was determined that these changes in the band gap are related with the structural changes with annealing. The temperature dependent conductivity measurements were carried out in the temperature range of 250‐430 K for all samples. The room temperature resistivity value of as‐grown film was found to be 0.7x10⁸ (Ω‐cm) and reduced to 0.9x10⁷ (Ω‐cm) following to the annealing. From the variation of electrical conductivity as a function of the ambient temperature, the activation energies at specific temperature intervals for each sample were evaluated. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Temperature dependence of lattice parameters of SBN single crystals in the vicinity of their structural phase transitions

Changes of lattice parameters of Sr_xBa_1‒xNb₂O₆ (0.35 < x < 0.72) solid solution single crystals were measured as a function of temperature. The X‐ray Bond’ method was used to carry out very precise measurements of the lattice parameters. Fine correlations between values of the lattice parameter and the Sr concentration in the solid solution of Sr_xBa_1‒xNb₂O₆ single crystals are found. A conventional analysis of lattice parameter data in terms of spontaneous strain and strain/order parameter coupling shows that a normal structural phase transition does occur. While the ferroelectric system (SBN26) displays a nearly tricritical behavior, β ≈ 0.20, the relaxor one (SBN61) complies with the two‐dimensional Ising‐model‐like criticality, β ≈ 0.17.     

Growth and Characterisation of (CuInTe2)1‐x(2 ZnTe)x Solid Solution Single Crystals

The crystal structure as well as the optical properties in the band gap region of (CuInTe₂)_1‐x(2 ZnTe)_x solid solution single crystals grown by directional freezing have been studied. The lattice constants exhibit a linear dependence on crystal composition. The chalcopyrite‐sphalerite phase transition was observed between x = 0.3 and x = 0.4°. The variation of the band gap with respect to crystal composition can be described by a quadratic expression.