基质固相分散-反相液相色谱法测定蔬菜中二甲戊乐灵农药残留

应用基质固相分散-反相液相色谱技术建立了提取、检测蔬菜中二甲戊乐灵农药残留的分析方法。研究了提取及测定条件对检测二甲戊乐灵的影响,确定了最佳提取条件:萃取吸附剂为弗罗里硅土,样品与弗罗里硅土吸附剂的比例为1∶4,洗脱剂为20 mL乙酸乙酯。二甲戊乐灵的测定线性范围为0.02~2.0 mg/L、r0.999。应用此方法测定了某些蔬菜样品中二甲戊乐灵农药残留,测定相对标准偏差为2.2%~5.2%。在几种蔬菜中的加标回收率为85%~93%,当样品为0.5 g时,方法检出限在5.5~10 ng范围内。     

加速溶剂萃取-气相色谱/质谱法测定灯盏花及其土壤中阿特拉津和二甲戊乐灵残留

建立了加速溶剂萃取(ASE)-气相色谱/质谱法(GC/MS)同时测定灯盏花及其土壤中阿特拉津和二甲戊乐灵2种除草剂的农药残留。样品采用丙酮-二氯甲烷(1∶1,V/V)加速溶剂萃取,弗罗里硅土柱层析净化,用GC/MS选择离子监测(SIM)法测定。结果表明,2种除草剂在0.05~2.00mg/L范围内线性良好,相关系数分别为0.9987~1.0000(灯盏花),0.9880~0.9980(土壤);在0.1、0.5和1.0mg/L添加水平下,2种除草剂在灯盏花及其土壤中的平均回收率分别为67.38%~104.02%和71.69%~105.58%,相对标准偏差(RSD)分别为3.21%~13.48%和2.65%~18.26%,方法的检出限(LOD)在灯盏花中为3.00~4.10ng/g,在土壤中为1.50~2.50ng/g。应用该法成功测定了云南省灯盏花及其土壤样品中2种除草剂残留。     

凝胶渗透色谱-气相色谱质谱法测定：花生中6种除草剂农药残留

建立了凝胶渗透色谱一气相色谱质谱（GPC～GC=MS）法测定花生中6种除草剂（氟乐灵、异恶草酮、甲草胺、二甲戊乐灵、乙氧氟草醚、喹禾灵）农药残留的方法。样品经乙腈提取,氨基固相萃取柱和凝胶渗透色谱净化,在选择离子扫描（SIM）模式下进行气相色谱质谱法测定,外标法定量。6种除草剂浓度在0．02-1．00mg／L范围内与色谱峰面积呈良好的线性,线性相关系数为O．9949～0．9998,添加回收率为77．8％-101．6％,测定结果的相对标准偏差为4．4％～11．4％（月=5）,方法的检出限为0．1～1．3μg／kg。     

二甲戊乐灵在溪黄草及土壤中的残留分析方法研究

本文对溪黄草样品采用丙酮-正己烷提取,活性炭-中性氧化铝柱净化,石油醚-丙酮淋洗前处理;土壤样品经乙腈提取等步骤前处理,建立了溪黄草及土壤中二甲戊乐灵残留的气相色谱-电子捕获检测器(GC-ECD)的分析方法。结果表明:二甲戊乐灵的最小检出量为0.1ng,其在溪黄草和土壤中的最低检测浓度均为0.01mg/kg,在溪黄草中的平均回收率为88.53%~90.45%,相对标准偏差(RSD)为1.33%~2.76%;在土壤中的平均回收率为93.94%~96.23%,RSD为4.67%~4.80%,二甲戊乐灵在0.01~2mg/L范围内具有良好的线性关系。     

磁性石墨烯纳米粒子固相萃取与气相色谱-质谱相结合测定环境水样中的三嗪类除草剂

将磁性石墨烯作为磁性固相萃取的吸附剂与气相色谱-质谱(GC-MS)相结合建立了环境水样中7种三嗪类除草剂残留的测定新方法。对影响萃取效率的一些因素如吸附剂用量、萃取时间、样品溶液的pH值、离子强度和解吸条件等进行了优化。在优化的实验条件下,7种三嗪类除草剂的富集倍数在574~968之间。测定西玛津、扑灭津、嗪草酮、西草净、氰草津的线性范围为0.01~10.0 μg/L,莠去津的线性范围为0.05~10.0 μg/L,扑灭净的线性范围为0.01~8.0 μg/L。线性相关系数为0.9968~0.9998,检出限(S/N=3)为1.0~5.0 ng/L。将本方法应用于井水、自来水和湖水等实际水样的分析,在0.5 μg/L和2.0 μg/L下的加标回收率为79.8%~118.3%,相对标准偏差为3.6%~10.5%。该法操作简单、富集倍数高,可满足水样中三嗪类除草剂残留的检测要求。     

气相色谱-串联质谱检测烟草中15种苯氧羧酸类除草剂残留

建立了气相色谱-串联质谱技术对烟草中15种苯氧羧酸类除草剂农药残留量的分析方法。样品采用乙腈提取、Carbon TPT固相萃取柱净化、三甲基硅烷化重氮甲烷衍生化,采用气相色谱-串联质谱对15种苯氧羧酸类除草剂进行测定,通过保留时间、选择离子及相对丰度定性,外标法定量。结果表明,15种苯氧羧酸类除草剂在20~1 000μg/L浓度范围内均呈良好线性关系,相关系数大于0.992,检出限为0.9~3.3μg/kg,定量下限为3.2~10.8μg/kg。在20,100,200μg/kg 3个加标水平下的平均回收率为71.5%~105.6%,相对标准偏差(RSD)为4.5%~14.9%。该方法简便、快速、灵敏,适用于烟草中15种苯氧羧酸类除草剂的同时检测。     

顶空-固相微萃取/气相色谱-质谱联用法快速分析海水中13种苯系物

建立了同时测定海水中常见的13种痕量苯系物(BTEX)的顶空-固相微萃取/气相色谱-质谱联用(HS-SPME/GC-MS)检测方法。利用涂有100μm Polydimethylsiloxane(PDMS)涂层的萃取头顶空萃取海水样品,GC-MS检测和外标定量法对目标物进行分析。实验对萃取纤维头的类型、萃取温度、萃取时间、解吸时间、样品体积等主要萃取条件进行了优化。在优化萃取条件下,13种苯系物的线性范围为0.16~32μg/L,相关系数为0.999 0~1.000 0,检出限为0.006~0.043μg/L。在3个加标水平(0.16、1.6、16μg/L)下,海水样品中13种苯系物的回收率为80.0%~117%,相对标准偏差(RSD,n=6)为2.0%~5.6%。该方法前处理简便易行、灵敏度高,为海水中痕量苯系物的检测提供了一种简便、快捷、环保的测定方法。     

二甲戊乐灵的气相色谱分析

1　引　　言二甲戊乐灵 (ｐｅｎｄｉｍｅｔｈａｌｉｎ)又称除草通、胺硝草 ,其化学名称为Ｎ (1 乙基丙基 ) 2 ,6 二硝基 3,4 二甲基苯胺 ,二甲戊乐灵为二硝基苯胺类除草剂 ,适用于玉米、大豆、棉花、蔬菜及果园中防除稗草、马唐、狗尾草等杂草。尤其在烟草田使用 ,不仅除杂草 ,而且可作为烟草抑芽剂使用 ,提高烟草的产量及质量 ,目前国内主要是作为烟草抑芽剂使用。国外使用相当广泛。该药的分析 ,较多采用高效液相色谱和气相色谱 质谱联用技术 ,有少部分采用毛细管气相色谱法。本文采用气相色谱填充柱及氢火焰离子化检测器分析二甲戊乐…     

气相色谱-质谱法测定化妆品中苯酚和氢醌

建立了气相色谱-质谱联用测定化妆品中苯酚和氢醌的检测方法.用甲醇作为提取试样,经HP-INNOWAX毛细管色谱柱分离,选择特征离子监测扫描模式(SIM)测定.结果表明:苯酚的方法线性范围为0.01~50μg/m L(r=0.999 96),检出限为0.05μg/g,加标回收率为91.3%~99.6%,相对标准偏差为1.5%~6.0%.氢醌的方法线性范围为0.02~50μg/m L(r=0.999 87),检出限为0.10μg/g,加标回收率为91.5%~99.7%,相对标准偏差为3.2%~5.5%.方法简单、快速、灵敏,可有效消除化妆品基质的干扰,适用于化妆品中苯酚和氢醌的定性、定量测定.     

浊点萃取-超高效液相色谱法检测水中戊菌唑残留量

建立了浊点萃取-超高效液相色谱分析(CPE-UPLC)法测定水中戊菌唑残留量的方法。以非离子表面活性剂PEG-6000为萃取剂,对色谱检测条件和浊点萃取参数进行了探讨和优化。浊点萃取条件为27 g/L PEG-6000,120 g/L Na2SO4,溶液p H为1.5,在45℃水浴中平衡15 min。在选定的色谱条件下,戊菌唑在0.025~5.0μg/m L时其质量浓度与检测信号峰面积呈线性关系,相关系数为0.9997,检出限为1.5μg/L;水样平均添加回收率为91.4%~92.9%,相对标准偏差为1.8%~2.6%。水样中戊菌唑添加质量浓度(0.025~5.0μg/m L)经CPE处理与UPLC检测信号呈线性关系,相关系数为0.9979,检出限为0.2μg/L,方法能满足农药残留检测的要求。     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Trichlorotrirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of four Linkage Isomeric Trichlorotrirhodanoosmates(IV) By treatment of fac-[OsCl₃I₃]^2? with (SCN)₂ in dichloromethane the linkage isomers fac-[OsCl₃(NCS)₃]^2? ( 1 ), mer-[OsCl₃(NCS)₂^c(SCN)]^2? ( 2 ), mer-[OsCl₃(NCS)(SCN)₂^t]^2? ( 3 ), and mer-[OsCl₃(NCS)(SCN)₂^c]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. X-Ray structure determinations have been performed on single crystals of fac-(Ph₄As)₂[OsCl₃(NCS)₃] (triclinic, space group P1 , a = 12.142(5), b = 13.233(5), c = 19.300(5) Å, α = 98.642(5)º, β = 100.509(5)º, γ = 112.514(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)₂^c (SCN)] · acetone (triclinic, space group P1 , a = 11.707(5), b = 13.238(5), c = 19.048(5) Å, α = 75.960(5)º, β = 88.981(5)º, γ = 69.999(5)º, Z = 2), mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^t] (triclinic, space group P1, a = 10.6861(12), b = 11.6587(5), c = 12.5232(5) Å, α = 112.069(8)º, β = 95.052(8)º, γ = 92.559(7)º, Z = 1) and mer-(Ph₄As)₂[OsCl₃(NCS)(SCN)₂ ^c] · 2acetone (triclinic, space group P1 , a = 11.444(5), b = 14.661(5), c = 15.830(5) Å, α = 75.790(5)º, β = 80.273(5)º, γ = 75.205(5)º, Z = 2). The complex anions are completely ordered. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 169.1º, 171.5º, 175.7º ( 1 ), 175.6º, 178.6º ( 2 ), 172º ( 3 ), and 173.1º ( 4 ) and Os? S? C angles of 106.2º ( 2 ), 106.1º, 106.6º ( 3 ), 105.1º, and 108.2º ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers have been assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.71 ( 1 ), 1.46 and 1.62 ( 2 ), 1.69 ( 3 ), and 1.61 ( 4 ), f_d(OsS) = 1.27 ( 2 ), 1.36 ( 3 ), 1.32, and 1.49 mdyn/Å ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Darstellung,Kristallstrukturen, Schwingungsspektren und Normalkoordinatenanalyse von vier bindungsisomeren Tetrachlorodirhodanoosmaten(IV)

Preparation, Crystal Structures, Vibrational Spectra, and Normal Coordinate Analysis of Four Linkage Isomeric Tetrachlorodirhodanoosmates(IV) By treatment of cis- or trans-[OsCl₄I₂]^2? with (SCN)₂ in dichloromethane the linkage isomers cis-[OsCl₄(NCS)₂]^2? ( 1 ), trans-[OsCl₄(NCS)(SCN)]^2? ( 2 ), cis-[OsCl₄(NCS)(SCN)]^2? ( 3 ) and trans-[OsCl₄(SCN)₂]^2? ( 4 ) are formed which have been separated by ion exchange chromatography on diethylaminoethyl cellulose. The X-Ray structure determinations on single crystals of cis-(Ph₄As)₂[OsCl₄(NCS)₂] (triclinic, space group P1 , a = 10.019(5), b = 11.702(5), c = 21.922(5) Å, α = 83.602(5)°, β = 85.718(5)°, γ = 73.300(5)°, Z = 2), trans-(Ph₄As)₂[OsCl₄ · (NCS)(SCN)] (monoclinic, space group P2₁/c, a = 18.025(5), b = 11.445(5), c = 23.437(5) Å, β = 94.208(5)°, Z = 4), cis-(Ph₄As)₂[OsCl₄(NCS)(SCN)] (triclinic, space group P1 , a = 10.579(5), b = 11.682(5), c = 22.557(5) Å, α = 81.073(5)°, β = 85.807(5)°, γ = 87.677(5)°, Z = 2) and trans-(Ph₄As)₂ · [OsCl₄(SCN)₂] (triclinic, space group P1 , a = 10.615(5), b = 11.691(5), c = 11.907(5) Å, α = 111.314(5)°, β = 96.718(5)°, γ = 91.446(5)°, Z = 1) reveal the complete ordering of the complex anions. The via N or S coordinated thiocyanate groups are located nearly direct above one of the cis-positioned Cl ligands with Os? N? C angles of 171.2° and 174.3° ( 1 ), 162.3° ( 2 ), 172° ( 3 ) and Os? S? C angles of 108.3° ( 2 ), 105.7° ( 3 ) and 105.5° ( 4 ). Using the molecular parameters of the X-Ray determinations the low temperature (10 K) IR and Raman spectra of the (n-Bu₄N) salts of all four linkage isomers are assigned by normal coordinate analyses based on a modified valence force field. The valence force constants are f_d(OsN) = 1.59 ( 1 ), 1.67 ( 2 ), 1.60 ( 3 ) and f_d(OsS) = 1.27 ( 2 ), 1.31 ( 3 ) and 1.32 mdyn Å^?1 ( 4 ). Taking into account increments of the trans influence a good agreement between observed and calculated frequencies is achieved.     

Comparative Thermogravimetric Studies of Poly(ether-ketone/sulfone) Imides and Their Parent Polymers: I. Poly(ether-ketone/sulfone) ethylimide

Thermogravimetry (TG) was employed to study the thermal degradation kinetics of poly(etherketone/sulfone)ethylimide (PEK-IE and PES-IE). The corresponding decomposition activation energies and reaction orders were obtained and the comparison was made with their parent polymerspoly(ether-ketone/sulfone) with Cardo group (PEK-C and PES-C). The results show that the degradation activation energies of PEK-IE and PES-IE were lower than that of PEK-C and PES-C; and two stages of the degradation process were found for all the four polymers. For PEK-IE and PES-IE, the activation energies in the first decomposition stage are much lower than that in the second stage and the two stages can be taken as slow induction and fast degradation, whereas for PEK-C and PES-C the activation energies in the first decomposition stage are larger than that in the second stage, and the two stages can both be taken as two fast degradation stages. The decomposition mechanism of the two stages was also speculated.This revised version was published online in November 2005 with corrections to the Cover Date.     

Darstellung und Kristallstruktur von (n-Bu4N)3[Ir(NCS)(SCN)5]

Preparation and Crystal Structure of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] The evaporated ethanolic extrakt of the reaction product of K₃[IrCl₆] and HNO₃, refluxed with an aqueous KSCN solution yields a mixture of the linkage isomers [Ir(NCS)_n(SCN)_6?-n]^3?, n = 0? 2, and small amounts of linkage isomeric chloropentarhodanoiridates(III), from which [Ir(NCS)(SCN)₅]^3? has been isolated by ion exchange chromatography on DEAE-cellulose. The X-Ray structure determination on a single crystal of (n-Bu₄N)₃[Ir(NCS)(SCN)₅] (monoclinic, space group P 2₁/a, a = 17.513(5), b = 32.607(5), c = 23.661(5) Å, β = 94.757(5)°, Z = 8) confirms the existance of a heteroleptic hexakis(thiocyanato(N)-thiocyanato(S))iridate(III) with an Ir? N distance of 2.03 Å and Ir? S bond lengths between 2.29 and 2.38 Å. The SCN groups with angles between 166 and 175° are nearly linear with Ir? S? C angles from 99.9 to 109.4°. The Ir? N? C angles of the two crystallographic independent anions are 166 and 174°.     

SYNTHESIS AND CHARACTERIZATION OF METAL COMPLEXES WITH AMPICILLIN

Abstract

The reaction, in water, of Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) ions with sodium ampicillinate at room temperature has allowed isolation of dimers with the following general formula [M(amp)Cl]₂ × nH₂O (n = 1.5?3.2). The complexes were characterized by elemental analyses, conductivity measurements, magnetic susceptibilities and spectroscopic methods (IR, Raman, EPR and UV-Visible). A dinuclear structure based on octahedrally coordinated metal ions is proposed.     

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性

PMDA-BPDA-HAB聚苯并噁唑的合成及耐热性;均苯四甲酸二酐;联苯四羧酸二酐;二羟基联苯胺;聚酰亚胺;聚苯并噁唑;耐热性     

Thermal Degradation of Poly(ε-caprolactone), Poly(L-lactic acid) and their Blends with Poly(3-hydroxy-butyrate) Studied by TGA/FT-IR Spectroscopy

Summary: The thermal degradation behavior of poly(ε-caprolactone) (PCL) and poly(L-lactic acid) (PLA) have been studied in different environment. It was found that these polymers undergo completely different degradation processes in nitrogen and oxygen atmosphere. In oxygen environment PCL and PLA mainly decompose to CO₂, CO, water and short-chain acids. In nitrogen atmosphere PCL releases 5-hexenioc acid, CO₂, CO and ε-caprolactone, whereas PLA decomposes to acetaldehyde, CO₂, CO and lactide. The polymer blends of poly(3-hydroxybutyrate) (PHB) with PCL and PLA decompose similar to the individual homopolymers with crotonic acid as the initial decomposition product of PHB.     

Energy relationship and the polarization of C_(60) cage in the endohedral complexes (X@C_(60))

In this paper, we carry out the calculation on the system (X@C60)(X=Li, Na, K, Kb, Cs; F, Cl, Br, I), where the position of X changes along 5 typical symmetry directions. For the calculation of quantum chemistry we use EHMO/ASED method, for the calculation of molecular mechanics we use Buckingham potential (exp-6-1) function, and for the calculation of thermo-chemical cycle we use individually isolating the processes such as the structure variation, charge transfer and charge distribution, and their interactions etc. The calculation results show that (1) In the region of radius r≈0.2 nm of the Ceo cage, the potential field is nearly spherical; (2) Except for Li and Na, the systems are the most stable with minimum energies at the center of C60 cage. For Li and Na, the systems are the most stable with minimum energies at r≈0.16 nm and r≈0.13 nm, respectively. In view of the interactive region of chemical bonds, the interactions between X and the C60 cage do not belong to the classical chemical bonds; (     

铜在3%NaCl溶液中腐蚀行为的光电化学研究

Cu以其优异的导电性、导热性和易加工性广泛用于工农业生产中．自然Cu的腐蚀和防腐成为人们很关注的问题．人们已经注意到，Cl-对Cu的腐蚀有影响，并进行过一些研究．但目前使用光电化学方法研究这一问题的文章尚不多见，特别是利用测量开路光电压及其瞬态波形这一现场的、无损的、灵敏的监测方法研究户对Cu电极腐蚀全过程的文章尚未见到．本文正是利用如上方法及XPS，AES方法，研究了Cl-对Cu电极腐蚀的全过程，取得了一些有意义的结果．1实验方法Cu电极用99．99％（质量分数）的Cu制成，面积约为39mm2；电极底部由Cu导线焊接引出，…     

On the morphological behavior of ABC miktoarm stars containing poly(cis 1,4-isoprene), poly(styrene), and poly(2-vinylpyridine)

Fundamental understanding of microphase separation in ABC miktoarm copolymers is vital to access a plethora of nonconventional morphologies. Miktoarm stars based on poly(cis 1,4-isoprene) (I), poly(styrene) (S), and poly(2-vinylpyridine) (V) are model systems, which allow systematic studies of the effects of composition, chemical microstructure, and temperature on the thermodynamics of microphase separation. Eleven ISV-x (I:S:V = 1:1:x, v:v:v) miktoarm copolymers were synthesized by anionic polymerization affording well-defined copolymers with a variable V arm. Equilibrium bulk morphologies of all samples, as evidenced by small-angle X-ray scattering, transmission electron microscopy (TEM), and self-consistent field theory, showed a systematic transition from lamellae (x ≈ 0–0.2) to [8.8.4] tiling (x ≈ 0.6–0.9) to cylinders in undulating lamellae (x ≈ 2–4) and, finally, to hexagonally packed core–shell cylinders (x ≈ 5–8). Chemical microstructure of the I arm [poly(cis 1,4-isoprene)] versus poly(3,4-isoprene) is shown to play important role in affecting morphological behavior. To reconcile differences between ISV-x star morphologies reported in the literature and those reported herein, even for the same composition, effects of the microstructure of I arm on the Flory–Huggins parameter between I and V arms were taken into account in a qualitative manner. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 1491–1504