A Proposal and Demonstration for Photonic Generation of a Microwave Signal by Incorporating a Microring Resonator

A proposal for photonic generation of a microwave signal is presented by employing a dual wavelength erbiumdoped fibre ring laser. In the laser, a microring resonator is cascaded with a tunable bandpass filter to serve as a dual-wavelength selector, an unpumped polarization maintaining erbium-doped fibre is used as a saturable absorber. By replacing the microring resonator with a delay interferometer to verify the proposal, a wavelengthtunable dual wavelength single longitudinal mode laser is demonstrated, and a microwave signal at 10.01 GHz with a linewidth of less than 25 kHz is obtained by beating the two wavelengths at a photodetector.     

利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

A Single-Longitudinal-Mode Dual-Wavelength cw Tm,Ho:GdVO4 Microchip Laser

A liquid nitrogen cooled dual-wavelength Tm,Ho：GdVO4 microchip laser is reported. The output dual wavelengths axe at 2038.9nm and 2050.1 nm. At each wavelength, the laser has a single longitudinal mode. The threshold power is nearly 20mW and the slope efficiency is 18.7%. The single longitudinal mode output power reaches 98mW, and the ratio of power is about 60% （2038.9nm） and 40% （2050.1 nm）.     

Noise characteristic of sum-frequency mixing orange solid-state laser

A laser-diode-pumped Nd:YVO₄ orange solid-state laser is described in this paper. The fundamental wavelengths at 1064 and 1342 nm oscillate simultaneously and generate the 593.5 nm wavelength by intracavity sum-frequency mixing in a KTP crystal using type II phase matching. The noise characteristic of laser output has been measured and analyzed at different pumping powers. The relationship between the amplitude noise of sum-frequency mixing output and the longitudinal modes of fundamental frequency has been investigated. The results show that the sum-frequency mixing output has low noise if one of the fundamental wavelengths is single longitudinal mode. The experiment shows that amplitude noise of the intracavity sum-frequency mixing laser is lower than that of intracavity frequency doubled laser with the same structure.     

EIT as a tool to observe dual wavelength operation of a semiconductor laser

We propose a simplified technique for dual wavelength operation of an extended cavity semiconductor laser, and its characterization using electromagnetically induced transparency (EIT). In this laser cavity scheme light beam is made converging before it incidences on the cavity grating. The converging angle of the beam creates two longitudinal oscillating modes of resonating cavity. Frequency separation between the longitudinal modes are measured with the help of beat frequency generation in a photodiode and creating pair of EIT spectra in Rb vapor. The pair of EIT dips that are generated due to dual wavelength of this laser (that is used as control laser) can be used to estimate frequency difference between the generated wavelengths. Width of EIT spectra can be used to estimate linewidth of individual wavelength components.     

A double wavelength DFB laser with an identical active area for CWDM

A novel distribute feedback (DFB) laser which gave two different wavelengths under two distinct work conditions was fabricated. The laser consists of two Bragg gratings with different periods corresponding to wavelength spacing of 20 nm in an identical active area. When driving current was injected into one of the different sections separately, two different wavelengths at 1542.4 and 1562.5 nm were realized. The side mode suppression ratio (SMSR) of 45 dB or more both for the two Bragg wavelengths were achieved. The fabricating process of the laser was just the same as that of traditional DFB laser diode. This device can be potentially used in coarse wavelength division multiplexer (CWDM) as a promising light source and the technology idea can be used to enlarge the transmission capacity in metro area network (MAN).     

Switchable dual-wavelength Erbium-doped fiber ring laser with cascaded fiber Bragg gratings

We have experimentally shown wavelength mode switching in a dual-wavelength Erbium-doped single cavity fiber laser where the initial two wavelengths of 1 nm spacing are determined by the cascaded reflection type short-period fiber Bragg gratings having two different centre wavelengths of 1550.5 and 1551.5 nm. The lasing mode depends on the polarization in the ring cavity to migrate from one wavelength to another or operates in both modes in a polarization beam splitter output. To effectively control the polarization in the ring cavity, the polarization controllers were positioned before and after the polarization beam splitter. This method of wavelength switching provides a simple way of mode tuning in dual-wavelength fiber lasers.     

Axial mode tuning of a single frequency Yb:YAG thin disk laser

We describe an arrangement for an Yb:YAG thin disk laser, which enables narrow bandwidth operation in single-frequency mode at freely selectable wavelengths within the broad tuning range of the laser. This is facilitated by a combination of a double-stage birefringent filter and an etalon inside the laser cavity. We investigate the wavelength selection characteristics of the single elements as well as their combination. A simple procedure is implemented for a computer-based automation of wavelength tuning. The reflectivity of the partially reflecting resonator mirror is optimised, and the laser pump power is adapted for best tuning performance. Single-frequency emission is achieved in a frequency range of 9.75 THz (wavelength range 1020 nm to 1055 nm). Each axial laser mode in this range can be selected individually. The axial mode separation of 0.47 GHz corresponds to wavelength steps of 1.7 pm at 1030 nm. PACS 42.55.Xi; 42.60.Fc; 42.60.Lh     

Dual band multi-branch lasing from a hybrid CO2 laser

By judicious imposition of longitudinal mode control onto a resonator cavity, the Q-value of which increases with decreasing wavelength in the 11 to 9 μm region, simultaneous oscillation was obtained on all the four branches from a hybrid CO2 laser when its low pressure section operates in the sub-threshold condition. In the above threshold operation of this section, the hybrid laser lases simultaneously only on 9P, 9R, and 10P branch lines. This revised version was published online in November 2006 with corrections to the Cover Date.     

Simultaneous two-wavelegth tunable dye laser with no mode competition and with a wavelength separation of more than 200 nm

A versatile simultaneous two-wavelength tunable dye laser is described. The two wavelengths are generated by means of a novel pumping arrangement which is suitable for operating with a linewidth between 0.001 nm and the broadband regime. There is no mode competition between the two wavelengths and the power ratio is continuously variable. If required, separate dyes can be used to generate the two wavelengths so facilitating a broad range of wavelength separations. Each wavelength is independently tunable but only one dispersive element is required in the cavity.     

A 795 nm gain coupled distributed feedback semiconductor laser based on tilted waveguides

The 795 nm distributed feedback lasers have great application in pumping the Rb D1 transition. In this paper, in order to realize specific 795 nm lasing, we designed tilted ridge distributed feedback lasers based on purely gain coupled effect induced by periodic current injection windows through changing the angle of the tilted ridge. The fabricated devices were cleaved into 2 mm-cavity-length, including 5 tilted angles. The peak output powers of all devices were above 30 m W.Single longitudinal mode lasing was realized in all tilted Fabry–Perot cavities using periodic current injection windows,with side mode suppression ratio over 30 d B. The total wavelength range covered 8.656 nm at 20℃. It was disclosed theoretically and experimentally that the output powers, threshold currents, and central wavelengths of the tilted ridge purely gain coupled DFB lasers were relevant to the tilted angles. The results will be instructive for future design of DFB laser arrays with different central wavelengths.     

Temperature dependence of interband transition energy in InGaAsN strain-compensated quantum-well and ridge-waveguide lasers fabricated with pulsed anodic oxidation

Ridge-waveguide InGaAsN triple-quantum-well strain-compensated lasers grown by metal organic chemical vapor deposition were fabricated with pulsed anodic oxidation. The laser’s output power reached 145 mW in continuous-wave mode at room temperature for a 4-?m -stripe-width laser. Continuous-wave single longitudinal mode operation was maintained at a high injection current level with a wavelength of 1287.3 nm at room temperature. Single longitudinal mode operation at 1317.2 nm was achieved at twice the threshold current at 100 °C. The band gap of InGaAsN in the quantum wells at different temperatures was calculated and compared to the measured temperature-dependent laser wavelength.     

Frequency doubling of wavelength locked laser diOde with a transmission-type filter in a confocal optical configuratiOn

Direct frequency doubling of a wavelength locked laser diode with an optical bandpass filter in a confocal optical configuration is demonstrated. The wavelength of the laser diode was locked in single longitudinal mode oscillation and tuned to phase-matching wavelength of a quasi-phase-matched second harmonic generation device based on a LiTaO₃ Waveguide. Stable blue light of 4.2 mW was obtained for incident power of 48 mW.     

High-resolution cavity-tuned ringdown spectrometer using a narrow-bandwidth pulsed laser source

A novel method of cavity ringdown spectroscopy is proposed to achieve high spectral resolution with tunable narrow bandwidth pulsed lasers. We demonstrate a cavity-tuned ringdown configuration in which only a single cavity mode is kept excited near the carrier frequency of a narrow bandwidth pulse laser. This is done simply by making a cavity resonance actively track the frequency reference served by the cw injection seed of the pulsed laser source. We present the servo mechanism used in the cavity resonance tracking, reliable procedures for transverse mode matching, and the evidence of single longitudinal mode excitation. The spectrometer performance is tested to record weak molecular overtone features of acetylene around the wavelength of 570 nm, showing cavity tracking stability within 5-MHz uncertainty which overcomes the bandwidth limit of pulsed laser sources itself. PACS 42.62.Fi; 42.60.Da; 33.20.Kf     

Wavelength-switchable erbium-doped fiber ring laser combined with a Fabry-Perot laser diode and a sampled grating

We present a wavelength-switchable erbium-doped fiber ring laser consisting of an anti-reflection coated Fabry-Perot laser diode (FP-LD) and a sampled fiber Bragg grating (SFBG). The wavelength switching is obtained easily by the shift of FP mode with respect to the reflection peaks of the SFBG. The proposed laser apparatus not only simultaneously emits two wavelengths but also switches between the two wavelengths by adjusting the modes of FP-LD with a change of the injection current of the FP-LD as little as ∼1 mA. The proposed wavelength-switchable erbium-doped fiber ring laser exhibits high laser performance with side-mode suppression ratio (SMSR) ?50 dB.     

Ar+激光和532 nm激光及其线偏振激光辐照光学模型下人正常小肠组织光学特性

采用双积分球系统和光辐射测量技术的基本原理以及运用生物组织的光学模型 ,研究了 4 76 5 ,4 88,4 96 5 ,5 14 5 ,5 32nm激光及其线偏振激光辐照人正常小肠组织的光学特性。结果表明 :组织对激光及线偏振激光的衰减系数和散射系数随着波长的减小而增大 ,而 5 14 5～ 5 32nm波长之间 ,线偏振光与非线偏振光入射则开始有明显差异。吸收系数是随着波长的减小而缓慢地增大 ,而 5 14 5～ 5 32nm波长之间吸收系数的改变则明显变小 ,与是否线偏振光入射无明显差异。平均散射余弦也是随着波长的减小而增大 ,光学穿透深度则是随着波长的增大而增大 ,折射率在这五个波长范围内的值在 (1 38～ 1 4 8)之间。Kubel ka Munk二流模型下组织对同一波长的激光及其线偏振激光的吸收系数、散射系数、总衰减系数、有效衰减系数没有显著性差异 (P >0 0 5 )。组织对不同波长的激光或其线偏振激光的吸收系数、散射系数、总衰减系数、有效衰减系数是有差异的。而在 5 14 5～ 5 32nm波长之间其光学特性参数有较为明显的差异。     

Multi-wavelength erbium-doped fiber ring laser based on wavelength-dependent polarization rotation with a phase modulator and an in-line comb filter

A stable room-temperature multi-wavelength erbium-doped fiber ring laser has been proposed and investigated experimentally. A phase modulator composed of a piece of fiber wrapped around a cylindrical piezoelectric transducer is used to suppress the mode competition. And the combined action between optical fiber and polarization-dependent isolator provides the wavelength-dependent loss induced by wavelength-dependent polarization rotation mechanism to flatten the output spectrum, tune the locations and improve the number of the lasing lines. Stable multi-wavelength lasing with wavelengths up to 23 and the wavelength spacing of 0.4 nm is demonstrated. Moreover, the pulse train output was also observed.     

A 1550-nm linearly tunable CW single-mode external cavity diode laser based on a single-cavity all-dielectric thin-film Fabry–Pérot filter

A 1550-nm linearly tunable CW single-mode external cavity diode laser (ECDL) based on a single-cavity all-dielectric thin-film Fabry–Pérot filter (s-AFPF) is proposed and realized in this paper. Its internal optical components as well as their operation mechanisms are introduced first, and then its longitudinal mode output characteristic is theoretically analyzed. Afterwards, we set up the experimental platform for the output characteristic measurement of this tunable ECDL; under different experimental conditions, we execute accurate and real-time measurements for the output central wavelength, output optical power, output longitudinal mode distribution, and the line-width of the tunable ECDL in its tuning process. By summing up the optimal experimental condition from the measured data, we obtain the optimal tunable relevant parameters ECDL of the tunable ECDL has a linear mode-hop-free wavelength tuning region of 1547.203 nm-1552.426 nm, a stable output optical power in the range of 40 μW-50 μW, and a stable output longitudinal mode distribution of a single longitudinal mode with a line-width in the range of 100 MHz-150 MHz. This tunable ECDL can be used in environmental gas monitoring, atomic and molecular laser spectroscopy research, precise measurements, and so on.     

Laser ablation and desorption from calcite from ultraviolet to mid-infrared wavelengths

3 ) at wavelengths ranging from the ultraviolet to the mid-infrared, including a Nd:YAG laser operated at the fundamental, second and third harmonics, and a tunable infrared free-electron laser (wavelength range 2.5–8 μm). The threshold for ablation and the topography of the irradiated spot were characterized by scanning electron microscopy. A clear indication of two distinct excitation mechanisms was observed, namely, cracks and fractures followed by exfoliation at ultraviolet to near-infrared wavelengths, in contrast to evaporative holes and scattered droplets in the mid-infrared. Plume emission/absorption spectroscopy, plume transmission and photoacoustic beam deflection were used to characterize the ablation plasma. The composition of atoms, molecules, or particles in the ablation plumes also has a distinctive variation as a function of the wavelength. The excitation mechanisms leading to ablation appear to be defect activation at ultraviolet to near-infrared wavelengths, molecular impurity absorption and resonant vibrational absorption of the calcite at mid-infrared. Received: 5 December 1996/Accepted: 6 January 1997     

Simple wavelength pre-selection and stabilization of the single-frequency operation of a microchip laser

This paper presents the concept and experimental verification of a simple method of wavelength pre-selection of a single frequency, second-harmonic generation SHG solid state laser Nd:YAG/KTP with the Lyot filter. Apart from well-known configuration of single-frequency operation, the Lyot filter to stabilization of the wavelength was used. The idea presented is based on a measurement of the losses introduced by the Lyot filter inside the laser cavity, or the maximums of laser output power as a measure of the assessment of the Lyot filter tuning to a required laser longitudinal mode, not requiring any external frequency standards. This method allows for the synthesization and stabilization of a selected wavelength from the spectrum range of the gain curve of the laser with the period determined by the “Lyot comb”. In the developed system 15 values of wavelength spaced at about 32 pm (～ 7.9 GHz) for the infrared radiation were obtained.